Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transient electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Proton radiation effects on electronic defect states in MOCVD-grown (010) β -Ga 2 O 3

The impact of 1.8 MeV proton irradiation on metalorganic chemical vapor deposition grown (010) β-Ga 2 O 3 Schottky diodes is presented. It is found that after a 10.8 × 10 13 cm –2 proton fluence the Schottky barrier height of (1.40 ± 0.05 eV) and the ideality factor of (1.05 ± 0.05 ) are unaffected. Capacitance–voltage extracted net ionized doping curves indicate a carrier removal rate of 268 ± 10 cm –1 . The defect states responsible for the observed carrier removal are studied through a combination of deep level transient and optical spectroscopies (DLTS/DLOS) as well as lighted capacitance–voltage (LCV) measurements. The dominating effect on the defect spectrum is due to the E c -2.0 eV defect state observed in DLOS and LCV. This state accounts for ~75 % of the total trap introduction rate and is the primary source of carrier removal from proton irradiation. Of the DLTS detected states, the E c -0.72 eV state dominated but had a comparably smaller contribution to the trap introduction. These two traps have previously been correlated with acceptor-like gallium vacancy-related defects. Several other trap states at E C -0.36, E C -0.63, and E C -1.09 eV were newly detected after proton irradiation, and two pre-existing states at E C -1.2 and E C -4.4 eV showed a slight increase in concentration after irradiation, together accounting for the remainder of trap introduction. However, a pre-existing trap at E c -0.40 eV was found to be insensitive to proton irradiation and, therefore, is likely of extrinsic origin. Furthermore, the comprehensive defect characterization of 1.8 MeV proton irradiation damage can aid the modeling and design for a range of radiation tolerant devices.

42 ENGINEERING↗
DOE OSTI2026

Pursuing Heteroleptic Ligand Design Principles for Photoactive Fe Complexes with Ultrafast X-ray Emission and Variable-Temperature Optical Spectroscopies

Understanding the key parameters that govern the photophysical and photochemical properties of transition metal complexes is essential for the development of efficient photosensitizers for photocatalytic applications. Achieving this objective necessitates clear and detailed investigations of their electronic excited states, for which time-resolved metal Kβ X-ray emission spectroscopy (XES) has proven highly effective. Here, we present a time-resolved Fe Kβ XES study of a heteroleptic Fe(II) polypyridyl carbene complex, [Fe(phen) 2 (C 4 H 10 N 4 )] 2+ (1; phen = 1,10-phenanthroline), utilizing both the valence-to-core and Kβ mainline spectral regions, complemented by variable-temperature transient optical absorption (VT-TA) spectroscopy. Detailed analysis of the time-resolved Kβ XES data, supported by density functional theory (DFT) calculations and an Eyring analysis of the VT-TA data, reveals parallel excited state relaxation dynamics that support an assignment of the long-lived excited state to a triplet metal-centered state. Placing these results in the context of prior studies of heteroleptic Fe(II) polypyridyl cyanide complexes motivated a series of DFT calculations to investigate the effects of ligand structural flexibility and arrangement. These calculations reinforce the experimentally derived conclusion that constraining structural flexibility with multidentate ligands significantly impacts the excited state relaxation dynamics. Furthermore, our study emphasizes that the arrangement of strong field ligands in heteroleptic complexes substantially affects the energy of Jahn–Teller active triplet metal-centered states in low-spin d 6 metal complexes. Together, these findings provide synthetic design principles for extending metal-to-ligand charge transfer excited state lifetimes of heteroleptic Fe complexes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Polymer connectivity governs electrophotocatalytic activity in the solid state

The reductive functionalization of inert substrates such as chloroarenes is a critical yet challenging transformation relevant to both environmental remediation and organic synthesis. Combining electricity and light is an emerging strategy to access the deeply reducing potentials required for single electron transfer to chloroarenes, yet this approach is limited by poor stability and mechanistic ambiguity. Here, in this work, we demonstrate heterogeneous electrophotocatalysis using redox-active rylene diimide polymers for the reduction of chloroarenes. We find that the electrophotocatalytic activity varies dramatically as a function of the rylene diimide and the redox-inactive polymer backbone. In particular, a flexible, non-conjugated perylenediimide polymer outperforms all other tested electrophotocatalysts. Transient absorption spectroscopy reveals that precomplexation between the doubly reduced perylenediimide and the haloarene substrate is key to productive catalysis. Overall, this work highlights heterogeneous electrophotocatalysis using insoluble redox-active organic materials and provides critical structure–property insights into solid-state electrophotocatalytic activity, informing the development of next-generation materials for sustainable synthesis.

electrocatalysis↗
DOE OSTI2023

Large-volume CdZnTe bar detectors characterized by laser-induced transient currents

In this work, we studied the free-carrier transport properties and space-charge formation/polarization in a CdZnTe bar-shaped radiation detector using the Laser-Induced Transient Current technique. We found out that a steady-state space charge ranging from 8 x 10 8 to 2.1 x 10 9 cm -3 is formed throughout the detector at about 0.5 s following biasing. The measured current waveforms were modeled by Monte Carlo simulations after taking into account the electric and weighting fields inside the detector and shielding box. Modeling of the unpolarized waveforms revealed an exceptionally high electron mobility-lifetime product μ e τ e ≥0.095cm 2 V -1 . The observed formation of positive space charge in the biased detector and linear scaling of the current waveform shapes on applied bias revealed that the detector polarization is attributed to carrier injection at the anode. In conclusion, measurements in pulsed and DC bias in modified electrode geometry proved the surface-charge formation.

47 OTHER INSTRUMENTATION↗
NASA NTRS1986

1986 Annual Conference on Nuclear and Space Radiation Effects, 23rd, Providence, RI, July 21-23, 1986, Proceedings

The present conference on the effects of nuclear and space radiation on electronic hardware gives attention to topics in the basic mechanisms of radiation effects, dosimetry and energy-dependent effects, electronic device radiation hardness assurance, SOI/SOS radiation effects, spacecraft charging and space radiation, IC radiation effects and hardening, single-event upset (SEU) phenomena and hardening, and EMP/SGEMP/IEMP phenomena. Specific treatments encompass the generation of interface states by ionizing radiation in very thin MOS oxides, the microdosimetry of meson energy deposited on 1-micron sites in Si, total dose radiation and engineering studies, plasma interactions with biased concentrator solar cells, the transient imprint memory effect in MOS memories, mechanisms leading to SEU, and the vaporization and breakdown of thin columns of water.

Ellis, Thomas D.↗
NASA NTRS2014

Temperature Control with Two Parallel Small Loop Heat Pipes for GLM Program

The concept of temperature control of an electronic component using a single Loop Heat Pipe (LHP) is well established for Aerospace applications. Using two LHPs is often desirable for redundancy/reliability reasons or for increasing the overall heat source-sink thermal conductance. This effort elaborates on temperature controlling operation of a thermal system that includes two small ammonia LHPs thermally coupled together at the evaporator end as well as at the condenser end and operating "in parallel". A transient model of the LHP system was developed on the Thermal Desktop (TradeMark) platform to understand some fundamental details of such parallel operation of the two LHPs. Extensive thermal-vacuum testing was conducted with two thermally coupled LHPs operating simultaneously as well as with only one LHP operating at a time. This paper outlines the temperature control procedures for two LHPs operating simultaneously with widely varying sink temperatures. The test data obtained during the thermal-vacuum testing, with both LHPs running simultaneously in comparison with only one LHP operating at a time, are presented with detailed explanations.

0000↗
DOE OSTI2022

Modelling general-relativistic plasmas with collisionless moments and dissipative two-fluid magnetohydrodynamics

ABSTRACT Relativistic plasmas are central to the study of black hole accretion, jet physics, neutron star mergers, and compact object magnetospheres. Despite the need to accurately capture the dynamics of these plasmas and the implications for relativistic transients, their fluid modelling is typically done using a number of (overly) simplifying assumptions, which do not hold in general. This is especially true when the mean free path in the plasma is large compared to the system size, and kinetic effects start to become important. Going beyond common approaches used in the literature, we describe a fully relativistic covariant 14-moment based two-fluid system appropriate for the study of electron–ion or electron–positron plasmas. This generalized Israel-Stewart-like system of equations of motion is obtained directly from the relativistic Boltzmann–Vlasov equation. This new formulation can account for non-ideal effects, such as anisotropic pressures and heat fluxes, not present in previous formulations of two-fluid magnetohydrodynamics. We show that a relativistic two-fluid plasma can be recast as a single fluid coupled to electromagnetic fields with (potentially large) out-of-equilibrium corrections. We keep all electron degrees of freedom, which provide self-consistent evolution equations for electron temperature and momentum. The out-of-equilibrium corrections take the form of a collisional 14-moment closure previously described in the context of viscous single fluids. The equations outlined in this paper are able to capture the full two-fluid character of collisionless plasmas found in black hole accretion and flaring processes around compact objects, as well Braginskii-like two-fluid magnetohydrodynamics applicable to weakly collisional plasmas inside accretion discs.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2009

Prognostics for Electronics Components of Avionics Systems

Electronics components have and increasingly critical role in avionics systems and for the development of future aircraft systems. Prognostics of such components is becoming a very important research filed as a result of the need to provide aircraft systems with system level health management. This paper reports on a prognostics application for electronics components of avionics systems, in particular, its application to the Isolated Gate Bipolar Transistor (IGBT). The remaining useful life prediction for the IGBT is based on the particle filter framework, leveraging data from an accelerated aging tests on IGBTs. The accelerated aging test provided thermal-electrical overstress by applying thermal cycling to the device. In-situ state monitoring, including measurements of the steady-state voltages and currents, electrical transients, and thermal transients are recorded and used as potential precursors of failure.

Celaya, Jose R.↗
DOE OSTI2023

Interactive Power to Frequency Dynamics Between Grid-Forming Inverters and Synchronous Generators in Power Electronics-Dominated Power Systems

With increased attention on grid-forming inverters as a power system stabilizing device during high shares of inverter-based resource operations, there is a present need for a transparent and methodical investigation of the inverted and direct power to frequency control capabilities and impacts of these devices on emerging power systems. Here, analysis of the frequency dynamics of the droop-controlled grid-forming inverter and the synchronous generator illuminates the inverted active power-frequency relationship and the frequency response order reduction, forming the basis for novel, nonlinear frequency control approaches. Device-level electromagnetic transient domain simulations corroborate the order-reduction findings, establish that a properly designed dc-side system has a negligible impact on power transfer and will not impede frequency regulation, and confirm the primary frequency response improvement with nonlinear control. Simulations of the 9- and 39-bus test systems validate the order reduction and associated decoupling of the nadir and rate of change of frequency in larger networks. Oscillatory mode analysis confirms the grid-forming benefit of increased damping; decreased damping is observed at shares above 80%, but not at 100%. Finally, simulations on a validated Maui power system model with a 96% of inverter-based resources model yield a trend toward a first-order response.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Reductive Dynamic and Static Excited State Quenching of a Homoleptic Ruthenium Complex Bearing Aldehyde Groups

A new homoleptic Ru polypyridyl complex bearing two aldehyde groups on each bipyridine ligand, [Ru(dab) 3 ](PF 6 ) 2 , where dab is 4,4′-dicarbaldehyde-2,2′-bipyridine, was synthesized, characterized, and utilized for iodide photo-oxidation studies. In acetonitrile (CH 3 CN) solution, the complex displayed an intense metal-to-ligand charge transfer (MLCT) absorbance maximum at 475 nm (ε = 22,000 M –1 cm –1 ) and an infrared (IR) band at 1712 cm –1 assigned to the pendent aldehyde groups. Visible light excitation in air-saturated solution resulted in room temperature photoluminescence (PL) with a maximum at 675 nm, a quantum yield, ϕ PL = 0.048, and an excited state lifetime, τ ο = 440 ns, from which radiative and nonradiative relaxation rate constants were extracted, k r = 9.1 × 10 4 s –1 and knr = 1.8 × 10 6 s –1 . Pulsed visible light excitation yielded transient UV–vis and IR absorption spectra consistent with an MLCT excited state; relaxation occurred with the maintenance of two isosbestic points in the visible region, and a lifetime that agreed with that measured by time-resolved PL. Cyclic voltammetry studies in a CH 3 CN solution with 0.1 M TBAPF 6 electrolyte revealed a quasi-reversible oxidation, E°(Ru III/II ) = +1.25 V vs. Fc +/0 , and three sequential one-electron reductions at −1.10, −1.25, and −1.54 V vs. Fc +/0 . Here, an excited state reduction potential of E°(Ru *2+/+ ) = +0.89 V vs. Fc +/0 was estimated with the Rehm–Weller expression. Titration of tetrabutylammonium iodide, TBAI, into a CD 3 CN solution of [Ru(dab) 3 ](PF 6 ) 2 resulted in significant shifts in the aldehyde H atom and 3,3′-biypridyl resonances that were analyzed with a 1:1 equilibrium model, from which K eq = 460 M –1 was extracted, increasing to 5800 M –1 when the solvent was changed to acetone-d 6 . Iodide titrations resulted in a significant quenching of the [Ru(dab) 3 ] *2+ lifetime and quantum yield in both CH 3 CN and acetone solvents. In CH 3 CN, the quenching was mainly dynamic and well described by the Stern–Volmer model, from which a quenching rate constant, k q , of 4.5 × 10 10 M –1 s –1 and an equilibrium constant, K eq , of 8.3 × 10 3 M –1 were obtained. In acetone, the static quenching pathway by iodide was greatly enhanced, with a K eq of 1.2 × 10 4 M –1 and a higher k q of 9.2 × 10 10 M –1 s –1 .

Aldehydes↗
DOE OSTI2025

Modulating Hole Transfer from CdSe Quantum Dots by Manipulating the Surface Ligand Density

The structure and density of surface capping ligands in cadmium chalcogenide quantum dots (QDs) are important considerations for controlling the efficiency of charge separation via the transfer of electrons or holes to molecular acceptors. Here we show how the manipulation of the surface ligand density of oleic acid-capped cadmium selenide (CdSe) QDs impacts the efficiency of hole transfer (HT) to polyoxovanadate alkoxides. Meerwein’s salt is used as a ligand-stripping agent, providing opportunities to quantitatively manipulate the ligand density at the surface of the nanocrystal, as evidenced by 1 H NMR spectroscopy. Time-resolved photoluminescence and transient absorption spectroscopies reveal that the extent of HT is quantitatively related to increased surface accessibility. Collectively, these results show that the reduction of surface ligand density can be used to tune the extent of interactions of molecular acceptors with QDs, providing a route to control charge-transfer processes relevant to improving the efficiency of QDs as photosensitizers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Fragmentation dynamics through geometrical distortion in low-energy electron attachment to carbon disulfide

The dissociation dynamics of dissociative electron attachment to carbon disulfide is studied using the velocity map imaging technique. Ion yields of the S− and CS− fragments are measured as a function of incident electron energy between 2 and 12 eV. Energy and angle-differential yields of the S− fragments are analyzed to investigate the dynamics of the CS2− anion around the 3.8-eV peak. The resonances involved in this fragmentation are identified and characterized in calculations using the well-known R-matrix method. Based on our measurements and the geometry dependence of the calculated resonances, we propose that a geometrical distortion of the transient negative-ion state of CS2 is necessary for S-CS bond dissociation to occur.

Paul, Anirban↗
NASA NTRS1974

HYDES: A generalized hybrid computer program for studying turbojet or turbofan engine dynamics

This report describes HYDES, a hybrid computer program capable of simulating one-spool turbojet, two-spool turbojet, or two-spool turbofan engine dynamics. HYDES is also capable of simulating two- or three-stream turbofans with or without mixing of the exhaust streams. The program is intended to reduce the time required for implementing dynamic engine simulations. HYDES was developed for running on the Lewis Research Center's Electronic Associates (EAI) 690 Hybrid Computing System and satisfies the 16384-word core-size and hybrid-interface limits of that machine. The program could be modified for running on other computing systems. The use of HYDES to simulate a single-spool turbojet and a two-spool, two-stream turbofan engine is demonstrated. The form of the required input data is shown and samples of output listings (teletype) and transient plots (x-y plotter) are provided. HYDES is shown to be capable of performing both steady-state design and off-design analyses and transient analyses.

Szuch, J. R.↗
NASA NTRS1979

Some TEM observations of Al2O3 scales formed on NiCrAl alloys

The microstructural development of Al2O3 scales on NiCrAl alloys has been examined by transmission electron microscopy. Voids were observed within grains in scales formed on a pure NiCrAl alloy. Both voids and oxide grains grew measurably with oxidation time at 1100 C. The size and amount of porosity decreased towards the oxide-metal growth interface. The voids resulted from an excess number of oxygen vacancies near the oxidemetal interface. Short-circuit diffusion paths were discussed in reference to current growth stress models for oxide scales. Transient oxidation of pure, Y-doped, and Zr-doped NiCrAl was also examined. Oriented alpha-(Al, Cr)2O3 and Ni(Al, Cr)2O4 scales often coexisted in layered structures on all three alloys. Close-packed oxygen planes and directions in the corundum and spinel layers were parallel. The close relationship between oxide layers provided a gradual transition from initial transient scales to steady state Al2O3 growth.

Smialek, J.↗
NASA NTRS1980

Study of radiation induced deep-level defects in proton irradiated AlGaAs-GaAs solar cells

Radiation induced deep-level defects (both electron and hole traps) in proton irradiated AlGaAs-GaAs p-n junction solar cells are investigated along with the correlation between the measured defect parameters and the solar cell performance parameters. The range of proton energies studied was from 50 KeV to 10 MeV and the proton fluence was varied from 10 to the 10th power to 10 to the 13th power P/sq cm. Experimental tools employed include deep-level transient spectroscopy, capacitance-voltage, current voltage, and SEM-EBIC methods. Defect and recombination parameters such as defect density and energy level, capture cross section, carrier lifetimes and effective hole diffusion lengths in n-GaAs LPE layers were determined from these measurements.

Li, S. S.↗
NASA NTRS1991

Characterization of devices, circuits, and high-temperature superconductor transmission lines by electro-optic testing

The development of a capability for testing transmission lines, devices, and circuits using the optically-based technique of electro-optics sampling was the goal of this project. Electro-optic network analysis of a high-speed device was demonstrated. The project involved research on all of the facets necessary in order to realize this result, including the discovery of the optimum electronic pulse source, development of an adequate test fixture, improvement of the electro-optic probe tip, and identification of a device which responded at high frequency but did not oscillate in the test fixture. In addition, during the process of investigating patterned high-critical-temperature superconductors, several non-contacting techniques for the determination of the transport properties of high T(sub c) films were developed and implemented. These are a transient, optical pump-probe, time-resolved reflectivity experiment, an impulsive-stimulated Raman scattering experiment, and a terahertz-beam coherent-spectroscopy experiment. The latter technique has enabled us to measure both the complex refractive index of an MgO substrate used for high-T(sub c) films and the complex conductivity of a YBa2Cu3O(7-x) sample. This information was acquired across an extremely wide frequency range: from the microwave to the submillimeter-wave regime. The experiments on the YBCO were conducted without patterning of, or contact to, the thin film. Thus, the need for the more difficult transmission-line experiments was eliminated. Progress in all of these areas was made and is documented in a number of papers. These papers may be found in the section listing the abstracts of the publications that were issued during the course of the research.

Whitaker, John F.↗
NASA NTRS2012

Temperature Induced Voltage Offset Drifts in Silicon Carbide Pressure Sensors

We report the reduction of transient drifts in the zero pressure offset voltage in silicon carbide (SiC) pressure sensors when operating at 600 C. The previously observed maximum drift of +/- 10 mV of the reference offset voltage at 600 C was reduced to within +/- 5 mV. The offset voltage drifts and bridge resistance changes over time at test temperature are explained in terms of the microstructure and phase changes occurring within the contact metallization, as analyzed by Auger electron spectroscopy and field emission scanning electron microscopy. The results have helped to identify the upper temperature reliable operational limit of this particular metallization scheme to be 605 C.

Okojie, Robert S.↗
DOE OSTI2026

Grand Challenges and Opportunities in Stimulated Dynamic and Resonant Catalysis

Traditional heterogeneous catalysis is constrained by kinetic and thermodynamic limits, such as the Sabatier principle and reaction equilibrium. Dynamic and resonant catalysts hold promise to overcome these limitations by actively oscillating a catalyst’s physical or electronic structure at the time scale of the catalytic cycle, allowing programmable control over reaction pathways, and leading to improved rate and selectivity. External stimuli such as temperature swing, mechanical strain, electric charge, and light can perturb catalyst surfaces in different ways, altering adsorbate coverage, binding energies, and transition states beyond what steady-state catalysis allows. This work surveys the current state of dynamic catalysis, introduces the concept of “ stimulando ” characterization for observing transient dynamics, and outlines key modeling, mechanistic, and benchmarking strategies to advance the field toward improved chemical transformation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗