Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stress testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Analysis of remote reflectin spectroscopy to monitor plant health

Remote non-contact reflection spectroscopy is examined as a method for detecting stress in Controlled Ecological Life Support System (CELSS) type crops. Lettuce (Latuca Sativa L. cv. Waldmans Green) and wheat (Triticum Aestivum L. cv. Yecora Rojo) were grown hydroponically. Copper and zinc treatments provided toxic conditions. Nitrogen, phosphorous, and potassium treatments were used for deficiency conditions. Water stress was also induced in test plants. Reflectance spectra were obtained in the visible and near infrared (400nm to 2600nm) wavebands. Numerous effects of stress conditions can be observed in the collected spectra and this technique appears to have promise as a remote monitor of plant health, but significant research remains to be conducted to realize the promise.

Woodhouse, R.↗
DOE OSTI2021

Investigating the relationship between radial pre-stress magnitude and ballistic projectile dwell in heavy confined ceramic targets

A series of bare silicon carbide ceramic armour disks were manufactured with high-strength steel containment to induce varying magnitudes of radial pre-stress. The induced radial stresses, ranging from 0 to 900 MPa, were measured via neutron diffraction and verified by comparison with numerical calculations. Four targets of each configuration, referred to as slip-fit, moderate pre-stress, and high pre-stress, were subject to ballistic testing with hemispherical-nose, tungsten heavy alloy long rod projectiles to determine the interface defeat transition velocity. In-situ diagnostics were unsuccessful in aiding the identification of interface defeat, necessitating a reliance on post-mortem assessment. A transition velocity of approx. 1000 m/s was identified for the unstressed target, increasing to approx. 1200 m/s for the pre-stressed configurations. No performance effect was discernible between the moderate (372 MPa) and high (899 MPa) pre-stress configurations, suggesting that an optimal performance may be achieved for lower pre-stress levels (i.e., <372 MPa). Additionally, the test results were compared with four semi-analytical predictions of interface defeat performance and good agreement was found, albeit with significant range in the model predictions.

42 ENGINEERING↗
NASA NTRS1990

Regolith-structure modeling of lunar facilities

The mechanical properties of lunar regolith are significantly different from terrestrial soils; at low stress levels, the ultimate strength envelope is highly nonlinear, and the material is essentially dilatant. The effects of platen friction, membrane confinement, and material self weight in triaxial tests have been shown to be of great significance in low stress level tests. An inverse identification technique has been devised to account for these effects where the load-displacement response of the entire specimen, including the boundary conditions and the self-weight, was analyzed by nonlinear finite element techniques so as to obtain true material parameters.

Perkins, Steven W.↗
NASA NTRS1984

Verification and application of the Iosipescu shear test method

Finite element models were used to study the effects of notch angle variations on the stress state within an Iosipescu shear test speciment. These analytical results were also studied to determine the feasibility of using strain gage rosettes and a modified extensometer to measure shear strains in this test specimen. Analytical results indicate that notch angle variations produced only small differences in simulated shear properties. Both strain gage rosettes and the modified extensometer were shown to be feasible shear strain transducers for the test method. The Iosipoescu shear test fixture was redesigned to incorporate several improvements. These improvements include accommodation of a 50 percent larger specimen for easier measurement of shear train, a clamping mechanism to relax strict tolerances on specimen width, and a self contained alignment tool for use during specimen installation. A set of in-plane and interlaminar shear properties were measured for three graphite fabric/epoxy composites of T300/934 composite material. The three weave patterns were Oxford, 5-harness satin, and 8-harness satin.

Walrath, D. E.↗
DOE OSTI2020

Experimental investigation on the effects of fabric architectures on mechanical and damage behaviors of carbon/epoxy woven composites

The mechanical behaviors and damage evolutions of carbon/epoxy woven fabric composites with three different geometries, i.e., one plain weave and two twill weave patterns with different areal densities, are studied under tensile loading. The effects of weave patterns on mechanical properties are investigated by monotonic and cyclic tension tests. Remarkable variations in stress–strain curve, Poisson’s ratio, residual strain and strain map exist in the three composites. Crimp ratio is found to be a critical factor to govern the mechanical properties. With smaller crimp ratio, a quasi-linear stress–strain curve with higher elastic modulus and strength is observed. The stress–strain curves of composites with higher crimp ratio contain transition stages with significant tangent modulus degradation. Elastic modulus, strength and damage initiation are all correlated with the crimp ratio linearly regardless of the fabric pattern. Dramatic nonlinear evolution in Poisson’s ratio occurs in the composite with higher crimp ratio. Cyclic tension results indicate that the residual strain is a more appropriate damage indicator than the unloading elastic modulus. Microstructure examination shows that damage developments are essentially related to the fabric geometry, and result in various mechanical behaviors. This work provides important insights into the geometry-deformation mechanism-mechanical property relationship of the woven composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural effects on the rotating bending fatigue behavior of Ti–6Al–4V produced via laser powder bed fusion with novel heat treatments

The rotating bending fatigue (RBF) behavior (fully reversed, R = -1) of additively manufactured (AM) Ti–6Al–4V alloy produced via laser powder bed fusion (PBF-L) was investigated with respect to different microstructures achieved through novel heat treatments. The investigation herein seeks to elucidate the effect of microstructure by controlling variables that can affect fatigue behavior in Ti–6Al–4V, such as chemistry, porosity, and surface roughness. In order to control these variables, different hot isostatic pressing (HIP) treatments at 800 °C, 920 °C, and 1050 °C with a 920 °C temper were applied to three sets of Ti–6Al–4V cylinders that originated from the same PBF-L build, such that there were 30 tests per condition. After HIP treatment, the specimens were machined and tested. The highest runout stress was achieved after sub-β transus HIP at 800 °C for 2 h at 200 MPa of pressure. A significant drop in fatigue strength was attributed to large prior-β grains and grain boundary α resulting from super-β transus HIP treated specimens. In conclusion, for the sub-β transus HIP specimens, differences in fatigue strength were attributed to α lath thickness, relative dislocation density, and dislocation boundary strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Relationships between fault characteristics and seismic responses in a large lab-scale tri-axial injection test conducted on a faulted Castlegate Sandstone

Here to investigate mechanisms causing microseismicity (M w < 2) at a CO 2 injection site, a large-scale triaxial block experiment was carried out on a faulted (saw-cut) cubic-meter of Castlegate Sandstone. The experiment consisted of injection tests at varying differential stresses, while monitoring and recording pore pressure and acoustic emissions (AEs). During the experiment, ~33,000 AEs and ~14 mm of horizontal displacement/slip, like a strike-slip fault movement, occurred. To understand the AE responses and ascertain fault characteristics near the located AEs, we modeled the topography of the fault surface, fault aperture, and fault-gouge thickness using pre- and post-experiment laser scans of the fault surface on each half of the block. Additionally, we characterized surface roughness parallel and perpendicular to slip. Models show crushing and flattening of the fault surfaces can be linked to the spatiotemporal distribution of AEs within 50 mm of the fault surface. Approximately 65% of AEs were in areas with small aperture (≤300 μm); thicker fault gouge was observed in adjacent areas with wider aperture and shows a two-fold reduction in grain size relative to unaltered Castlegate Sandstone. This work provides a conceptual understanding on fault surface evolution, which can be applied towards modeling of seismic slip.

58 GEOSCIENCES↗
DOE OSTI2025

Establishing a process-structure-property-performance framework for SLS additive manufacturing through integrated multiscale modeling

This study presents a comprehensive suite of high-fidelity computational models that integrate multiscale and multiphysics simulations to capture the full Selective Laser Sintering (SLS) additive manufacturing process—from initial melting and solidification to mechanical response under external loads. Process simulations are linked with mechanical analysis through Representative Volume Elements (RVEs), establishing a process-structure–property-performance framework. The interaction between laser light and polyamide 12 (PA12) powder is modeled, accounting for laser characteristics and the optical, thermal, and geometrical properties of the powder. The heat source is incorporated into a heat transfer model, coupled with crystallization kinetics and densification models to predict material density and crystallinity. The porosity distribution from the densification model and crystallinity interpolated from experimental data are used to construct the RVEs. A multi-mechanism constitutive model is then calibrated using mechanical tests to predict the stress–strain response. Simulation results show good agreement with experimental data in terms of porosity, crystallinity, and mechanical performance when sufficient laser power (62 W or higher) is used. This research supports the inverse design of 3D-printed structures by introducing a high-fidelity framework that combines multiscale and multiphysics modeling with experimental calibration for predictive and performance-driven additive manufacturing.

SLS↗
DOE OSTI2024

Crystal plasticity modeling and analysis for the transition from intergranular to transgranular failure in nickel-based alloy Inconel 740H at elevated temperature

The precipitation-strengthened Nickel alloy Inconel® 740H® (IN740H) exhibits increased ductility at higher applied strain rates during quasi-static tensile tests at an elevated temperature of 760°C. The examination of fracture surfaces in this context reveals a noteworthy transition of underlying fracture mechanisms from transgranular to intergranular fracture as the applied strain rate decreases from 1×10 -3 / s to 0.83×10 -4 / s . To thoroughly understand the mechanical response of IN740H under these conditions, this study develops a crystal plasticity finite element (CPFE) model. Further, this model incorporates various deformation mechanisms including dislocation slips, climb, and grain boundary sliding, which are relevant to the test conditions. The model is calibrated using data from both tensile tests at different strain rates and creep tests across a broad stress range at 760°C, enabling the accurate determination of model parameters for each mechanism. Simulation results well captured the experimental observations of different failure modes. At higher strain rates, the model shows a dominance of dislocation slip leading to heterogeneous plastic deformation and formation of transgranular shear bands causing the failure, while at lower strain rates, an increased activity of grain boundary sliding causes grain boundaries crack leading to intergranular failure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Additive manufacturing of an ultrastrong, deformable Al alloy with nanoscale intermetallics

Abstract Light-weight, high-strength, aluminum (Al) alloys have widespread industrial applications. However, most commercially available high-strength Al alloys, like AA 7075, are not suitable for additive manufacturing due to their high susceptibility to solidification cracking. In this work, a custom Al alloy Al 92 Ti 2 Fe 2 Co 2 Ni 2 is fabricated by selective laser melting. Heterogeneous nanoscale medium-entropy intermetallic lamella form in the as-printed Al alloy. Macroscale compression tests reveal a combination of high strength, over 700 MPa, and prominent plastic deformability. Micropillar compression tests display significant back stress in all regions, and certain regions have flow stresses exceeding 900 MPa. Post-deformation analyses reveal that, in addition to abundant dislocation activities in Al matrix, complex dislocation structures and stacking faults form in monoclinic Al 9 Co 2 type brittle intermetallics. This study shows that proper introduction of heterogeneous microstructures and nanoscale medium entropy intermetallics offer an alternative solution to the design of ultrastrong, deformable Al alloys via additive manufacturing.

Science & Technology - Other Topics↗
DOE OSTI2024

Transient behavior of oxide fuels with controlled microstructure and Cr2O3 additive

Abstract Microstructure and Cr 2 O 3 doping profoundly impact the thermal-mechanical properties and fracture of oxides fuels. It is a challenge to study the transient behavior of nuclear fuels under loss-of-coolant-event (LOCA). In this study, the crack behavior of UO 2 pellets with controlled grain structure and Cr 2 O 3 doping was tested with rapid power ramping (300−900 °C per min) mimicking a prototypical LOCA heating profile. Dense micron-sized UO 2 pellets display well-maintained integrity without cracking with the ramping up to 1500 °C at a heating rate of 8 °C per second. Fracture occurs in both pure and Cr 2 O 3 -doped dense nano-sized UO 2 pellets. The Cr 2 O 3 doped oxide fuel pellet with a larger grain size (~ 22.2 μm) displays the best performance under LOCA testing due to its highest thermal conductivity under high temperature. FEA calculations suggest a temperature gradient across the fuel pellet during transient testing, resulting in residual stress and cracking, which can be correlated with their thermal-mechanical properties.

Zhao, Dong (ORCID:0000000191377257)↗
DOE OSTI2022

Nonnuclear Experimental Capabilities to Support Design, Development, and Demonstration of Microreactors

This work provides a summary of selected experimental capabilities being developed to support nonnuclear testing and demonstration of technology in support of microreactors under the U.S. Department of Energy’s (DOE’s) Microreactor Program. Major capabilities include the Single Primary Heat Extraction and Removal Emulator (SPHERE) and the Microreactor Agile Non-nuclear Experimental Test Bed (MAGNET). The SPHERE facility allows for controlled testing of the steady-state and transient heat rejection capabilities of a single heat pipe using electrical heaters that simulate nuclear heating. The facility is capable of monitoring axial temperature profiles along the heat pipe and surrounding test articles during startup, steady-state operation, and transients. Instrumentation includes noncontact infrared thermal imaging, surface thermocouples, spatially distributed fiber optic temperature and strain sensors, electrical power meters, and a water-cooled, gas-gap calorimeter for quantifying heat rejection from the heat pipe. The facility can be operated under both vacuum and inert-gas conditions. The MAGNET facility is a large-scale, 250-kW electrically heated microreactor test bed to enable nonnuclear experimental evaluation of a variety of microreactor concepts. It can be supplied to electrically heat a scaled section of a microreactor and further test the capabilities of heat rejection systems. The initial MAGNET experiments will support technology maturation and reduce uncertainty and risk associated with the design, operation, and deployment of monolithic heat pipe–based reactors. However, this test bed can broadly be applied to multiple microreactor concepts to evaluate a wide range of thermal-hydraulic and structural phenomena such as interface coupling with power conversion units and other collocated systems. MAGNET can evaluate integral thermomechanical effects during electrical heating of an array of heat pipes in a larger test article. Examples of initial testing will include thermal stresses in the monolith and the impact of debonding of a heat pipe from the core block and how that failure could impact surrounding heat pipes, i.e., understanding the potential for cascading failure. This work also discusses some modeling capabilities that can support experiment design, analysis, and interpretation, including the heat pipe code Sockeye and a comparison of thermal-structural simulations performed using ABAQUS and STAR-CCM+.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Formation and dissociation of shear-induced high-energy dislocations: insight from molecular dynamics simulations

Solid-phase processing (SPP) allows one to create complex microstructures, not achievable via thermal processing alone. The resulting structures exhibit a rich palette of defects, both thermal and non-thermal, including defect substructures, such as dislocation networks. It is essential to understand the mechanisms of deformation and defect structure formation to guide SPP towards achieving desired microstructures and material properties. In this study, large-scale molecular dynamics simulations are used to investigate the effects of inhomogeneous strain distribution, that mimics deformation conditions of tribological tests, on the evolution of defects under severe shear deformation in polycrystalline Al. Analysis of defect nucleation and reaction pathways reveals that strong geometric constraints suppress the nucleation and slide of low energy dislocation 1/2$\langle110\rangle${111} but promote the nucleation and slide of high energy dislocations, such as [$1\bar1$0] (001) and 1/2 [$1\bar1$$\bar2$]($1\bar1$1). Further, a rough contact surface, characteristic to tribological tests, imposes an inhomogeneous stress field leading to inhomogeneous defect substructures due to location-dependent activation of slip systems. The results suggest that high-energy dislocations can dominate the evolution of grain structures in highly constrained environments, which should be considered in modeling plastic deformation and grain refinement during SPP.

42 ENGINEERING↗
DOE OSTI2021

Load Deflection Data (LDDATA)

The current data set is load deflection data (Stress vs strain for compression stress and stress vs elongation for tension stress) from a material test. The goal of the test was to characterize this rubber-like material by looking at different variables: sample creation process, anisotropy, temperature, etc. The data will be used with the Texas A&M Online Research Experience for Undergraduates (O-REU) program. This program is joint with LANL. The student is not an official LANL student so they will not be able to access data and documents on the yellow. The load deflection data set is unclassified and will be sent to the student for analysis. Analysis will include curve fitting, scalar value analysis (stiffness, toughness, etc.) and analysis of variance to determine what variables statistically affect the response while correcting for covariates (temperature soak time and humidity). Data will be stored as Matlab structs and as HDF5 files. Same data, different formats.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Systems Framework to Enhance the Potential of Camelina as Oilseed Crop (Final Report)

To alleviate the dependency of the United States on fossil fuels, particularly from foreign sources, the transition to biofuel crops has long been proposed as a crucial part of the long-term solution. Camelina sativa has emerged as one of the most promising oilseed crops for domestic biofuel and bioproduct production due to its low agronomic input requirements, natural resilience to a wide range of biotic and abiotic stresses, and the successful testing and approval of its oil-based blends for use in liquid transportation fuels.

09 BIOMASS FUELS↗