Results for “performance test” — Page 68

DOE OSTI2020

AFIP6-MkII and RERTR-12 Porosity Data Collection and Analysis for Modeling and Simulation

Gathering data for the improvement of nuclear fuel modeling and simulation efforts is the primary driver for this work. Mechanistic models allow for a better understanding of the material on a micro- and macrostructural level while saving time and money over traditional experiment efforts. Historically, summarized data and correlations are the inputs for empirical material models and model validation. When improving these models for nuclear fuels with experimental results, there is a lack of reliable data readily available. Experiments - RERTR-12 and AFIP6-MkII - were conducted to understand the irradiation behavior of metallic U-10Mo monolithic fuels for use in extreme reactor environments such as research reactors like the Advanced Test Reactor (ATR) or the High Flux Isotope Reactor (HFIR). Microstructural characteristics of fission gas pores (FGP) in each experiment are collected using an automated image analysis technique developed at the University of Florida and presented here. A series of statistical tests are performed to explore the reliability of the results, as well as understand where the data is lacking and what future data collection is necessary to provide sufficient information to assist modeling efforts. The focus is on the porosity, pore size, and eccentricity of FGPs formed during irradiation in three AFIP6-MkII samples and one RERTR-12 sample. From the analysis, it is clear there are substantial impacts of fission density on the pore structure, but there also exist also underlying connections between each sample and the behavior observed in the pores. Further analyses of the pre- and post-irradiation microstructure are needed to improve the understanding of these connections. An early method for microstructural data analysis is presented within and is currently being expanded to include other microstructure data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Cost Effective 6.5% Silicon Steel Laminate for Electric Machines

Iowa State University teamed with United Technologies Research Center and the University of Delaware and demonstrated a high switching frequency non-rare earth permanent magnet motor. A prototype motor with 400 Hz switching frequency, dummy MnBi permanent magnet with 8 MGOe energy density, and 6.5%Si steel as the laminate materials was designed, built, and tested. The performance of the prototype met the expectations showing a higher frequency motor enabled by 6.5%Si steel is a viable approach to meet DOE 2022 cost and performance targets for electric vehicle drive. Adoption of 6.5%Si steel will result in 3% improvement in energy conversion efficiency of the soft magnetic materials. In addition, the ability to use non-rare earth magnet for high power density application effectively mitigate the risk of EV traction motor from the rising rare earth price.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Mixed-Mechanism Stimulation Enabled Enhanced Geothermal Systems (CRADA FP00007509 Final Report)

In this project, we aimed to develop a robust, novel EGS design that would enable broad deployment of geothermal energy at costs competitive with other sources of renewable energy. The technical objectives included developing reservoir models for synthetic geothermal systems that meet target reservoir performance characteristics, performing a quantitative assessment of selection criteria for candidate geothermal sites, perform proppant studies under relevant geothermal conditions, and complete an induced seismicity risk analysis for potential geothermal development sites. The project team made significant progress towards these objectives. Specifically, we developed a prioritization to rank candidate sites for suitability of our technology based on 10 separate technical, operational, logistic, regulatory, and commercial criteria. The team performed laboratory testing at Lawrence Berkeley National Laboratory to characterize the functionality of several different types of proppant materials at temperatures of up to 200 C for durations of up to 9 weeks. We also created an Induced Seismicity Mitigation Plan for the top two sites selected for our future field demonstrations.

58 GEOSCIENCES↗

DOE OSTI2021

Diagnostic Testing for COVID-19 Bridging Study for QIAamp Viral RNA Extraction vs Beckman RNAdvance vs Thermofisher MagMAX

This report describes testing that was performed by LANL’s Biological Agent Testing Lab (BATL) to validate modifications to the CDC EUA 2019-Novel Coronavirus (2019- nCoV) Real-Time RT-PCR Diagnostic Panel (EUA-CDC-nCoV-IFU). BATL intends to implement the modifications to increase thoughput for daily testing . BATL validated the viral RNA extraction process, using the orignial component, QIAamp Viral RNA Mini Kit (Cat # 52906) and the new components, Beckman Coulter magnetic 96-well plate RNAdvance Viral kit (Cat # C63510), Thermofisher MagMAX Viral/Pathogen Nucleic Acid Isolation Kit (Cat # A48310). Equivalency was demonstrated between the original component and the Beckman Coulter magnetic 96-well plate RNAdvance Viral kit (Cat # C63510). Equivalency was also demonstrated between the original component and the Thermofisher MagMAX Viral/Pathogen Nucleic Acid Isolation Kit (Cat # A48310). Subsequently, substitution of the original component with either of these kits for viral RNA extraction increased BATL’s extraction capability from 100 samples per day to 279 samples per day.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

Connecting Dynamic Strain Aging to Deformation Processing in Magnesium-Calcium-Based Alloys

Fuel consumption can be improved by reducing car weight with substitution of aluminum and steel parts with magnesium (Mg). Magnesium formability at room temperature is limited due to strong basal texture generated prior processing. Shear band nucleation, observed under conditions in which dynamic strain aging (DSA), have been attributed to be responsible for texture weakening in dilute Mg – Rare Earths (RE) alloys. A low–cost substitution of RE is calcium (Ca) with similar atomic size. It is hypothesized that deformation of Mg – Ca alloys under DSA conditions improves Mg formability. In this study, Mg–Ca and Mg–Ca–Zn alloys were characterized using optical microscopy, XRD, and SEM/EDS. Compression testing was performed between 200 and 300C at different strain rates to observe DSA behavior. This work was performed under DOE Award Number DE-EE0007756.

Manuel, Michele↗

DOE OSTI2021

Analysis and Testing of Parsons NGS Solvent Formulation

Three drums containing solvent used during the Next Generation Solvent Test (NGST) conducted by Parsons in 2014-2015 were received at SRNL. After homogenization, samples from each drum were removed, and a composite sample prepared. This composite was analyzed to determine current SRNL characterization method efficacy, and to determine if the 1,3-dicyclohexyl-2- (isotridecyl) guanidine (DCiTG) suppressor could be selectively removed. The results of this work indicate that the titration analytical method currently employed at SRNL is effective at quantitating the DCiTG. The nuclear magnetic resonance (NMR) method at SRNL can detect the DCiTG, as well its amine and urea decomposition products. However, further development work will be required to allow the 1 H NMR method to quantitate these species. A series of three washing tests were performed on composite samples of the solvent. The results show that up to 67% of the DCiTG was removed from the solvent by simple washing, at multiple ratios of solvent: aqueous phase. This may indicate that a simple pathway exists to wash out the DCiTG and reclaim the solvent (~150 gallons) for future use at the Salt Waste Processing Facility (SWPF).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

Co-Development of Oscillating Water Column (OWC) and Offshore Power Station

The project proposed an Oscillating Water Column (OWC) at a low power rating (1-5kW); to build a prototype and perform field testing within 1–3 years and achieving a commercial version of the OWC 3–5 years. We selected the OWC off-the-shelf components to secure the supply-chain sources and to warrant stable and minimum pricing. We want to curtail the capital cost by reducing the weight and volume of the overall system structure at the design level by designing a high-speed turbine generator and optimizing the airspeed amplification. We want to minimize the operational and maintenance (O&M) costs through simplified architecture, minimal parts, modular/plug-and-play, and easy access designs.

16 TIDAL AND WAVE POWER↗

DOE OSTI2021

Library of Advanced Materials for Engineering (LAMÉ) 5.0

Accurate and efficient constitutive modeling remains a cornerstone issue for solid mechanics analysis. Over the years, the LAMÉ advanced material model library has grown to address this challenge by implementing models capable of describing material systems spanning soft polymers to stiff ceramics including both isotropic and anisotropic responses. Inelastic behaviors including (visco)plasticity, damage, and fracture have all incorporated for use in various analyses. This multitude of options and flexibility, however, comes at the cost of many capabilities, features, and responses and the ensuing complexity in the resulting implementation. Therefore, to enhance confidence and enable the utilization of the LAMÉ library in application, this effort seeks to document and verify the various models in the LAMÉ library. Specifically, the broader strategy, organization, and interface of the library itself is first presented. The physical theory, numerical implementation, and user guide for a large set of models is then discussed. Importantly, a number of verification tests are performed with each model to not only have confidence in the model itself but also highlight some important response characteristics and features that may be of interest to end-users. Finally, in looking ahead to the future, approaches to add material models to this library and further expand the capabilities are presented

36 MATERIALS SCIENCE↗

DOE OSTI2021

Welded and Hydrogen Charged Zircaloy-4 and Welded Stainless Steel 347 Property Data and Microstructures for the Target Solution Vessel and Support Lines of SHINE

SHINE Medical Technologies is developing a facility that will produce molybdenum-99 for medical isotope procedures. As part of this facility, a metal tank, called the target solution vessel (TSV), will hold a uranyl sulfite solution. The TSV must withstand neutron irradiation near room temperature and potential corrosion from the aqueous solution. The large cylindrical TSV will be fabricated by welding and will have numerous pipes and connections also attached via welding. The vessel and those pipes will have varying thicknesses so both gas tungsten arc welding (GTAW) and flux-cored arc welding (FCAW) will be necessary to fabricate different sections. The original material under consideration for the TSV was Zircaloy-4 (Zry-4), but it is known to form a hydride which can degrade its mechanical properties. Thus, some investigation here is focused on the effects of hydrogen uptake in the Zry-4. Additionally, the alternative material being considered is AISI 347, a stainless steel. Both materials have little existing data for their neutron irradiation behavior below 100°C, and both have open questions on the weld behavior under neutron irradiation. Testing has focused on characterizing their weld properties with tensile tests and performing neutron irradiation of samples in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL).

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2021

Library of Advanced Materials for Engineering (LAMÉ) 5.2

Accurate and efficient constitutive modeling remains a cornerstone issue for solid mechanics analysis. Over the years, the LAMÉ advanced material model library has grown to address this challenge by implementing models capable of describing material systems spanning soft polymers to stiff ceramics including both isotropic and anisotropic responses. Inelastic behaviors including (visco)plasticity, damage, and fracture have all incorporated for use in various analyses. This multitude of options and flexibility, however, comes at the cost of many capabilities, features, and responses and the ensuing complexity in the resulting implementation. Therefore, to enhance confidence and enable the utilization of the LAMÉ library in application, this effort seeks to document and verify the various models in the LAMÉ library. Specifically, the broader strategy, organization, and interface of the library itself is first presented. The physical theory, numerical implementation, and user guide for a large set of models is then discussed. Importantly, a number of verification tests are performed with each model to not only have confidence in the model itself but also highlight some important response characteristics and features that may be of interest to end-users. Finally, in looking ahead to the future, approaches to add material models to this library and further expand the capabilities are presented.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Staged OMB for Modular Gasifier/Burner

The goal of this final project report is to comprehensively summarize the work conducted on project DE-FE0031506. In accordance with the Statement of Project Objectives (SOPO), the University of Kentucky Center for Applied Energy Research (UK CAER) (Recipient) has developed a staged opposed multi-burner (OMB) gasifier, scaled down from a commercial gasification technology to utilize coal slurry as feed for the high-temperature gasification. The project involved the design, fabrication, commissioning, parametric testing, and performance validation of the entrained gasifier with multiple burners to narrow the major near-term technical gaps that impede the application of small-size gasification by modularizing the system. Project results verified the UK CAER approach to address the major technical challenges on the gasification modularization for a distributed application at a small scale of 1-5 MWe, while maintaining advantages in cost and flexibility, which include: 1) a cost-effective burner configuration to provide high flexibility in both load and fuel feed; 2) the modularized staged-OMB to provide better gasification performance such as a desired temperature profile, better fuel conversion, better gasification efficiency, and long lifetimes of the refractory wall and burners; and 3) load control simply through changing the number of burners firing. UK CAER’s staged gasifier configuration, fuel blend performance, and economic evaluation shows promise, as summarized in this report, as an effective means for improved gasification efficiency with reduced operation cost and process complexity.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Laboratory Wind Turbine Blade Static Testing of the Sandia National Rotor Testbed 13-Meter Wind Turbine Blade

The Sandia National Laboratories (SNL or Sandia) National Rotor Testbed (NRT) blade is a new design for experimental research and development at the Sandia Scaled Wind Farm Technology (SWiFT) facility, located at Texas Tech University’s National Wind Institute Research Center in Lubbock, TX. Four NRT blades were manufactured, with three blades for operation at the SWiFT facility, and one blade intended for structural validation. A series of structural validation tests including property testing, static strength testing, and fatigue testing were performed at the National Renewable Energy Laboratory (NREL). This report documents the static and fatigue load cases applied to the NRT blade.

17 WIND ENERGY↗

DOE OSTI2021

Structural Health Monitoring: Using an Autoencoder to Identify Damage in a Bolted Joint [Capstone Project]

Los Alamos National Laboratory (LANL) is an important fixture in the United States Department of Energy’s (DOE) National Nuclear Security Agency (NNSA) complex. LANL is one of the largest national laboratories in the country, and the laboratory’s primary mission is to support the nation’s nuclear stockpile. The lab functions as a design agencies for the NNSA and performs extensive testing on weapons as part of that mission. The shock and vibration test team at LANL utilizes electrodynamic shaker systems for important qualification testing in support of the laboratory’s mission. Modern engineering relies heavily on bolted joints to connect two objects. During these shaker tests, engineers depend on bolted joints to secure the test article to a fixture and the fixture to the table. The test article may be hazardous and contain high explosives which could create a safety issue if a bolted joint failed. A loss of preload in a bolt will affect the way energy is input to the system and may introduce nonlinearities as the joint opens and closes. The loss of preload can create challenges controlling the test and make acquired signals useless. Being able to monitor preload within bolted joints during testing can improve the quality of the data and keep workers safe.

42 ENGINEERING↗

DOE OSTI2021

Library of Advanced Materials for Engineering (LAMÉ) 5.4

Accurate and efficient constitutive modeling remains a cornerstone issue for solid mechanics analysis. Over the years, the LAMÉ advanced material model library has grown to address this challenge by implementing models capable of describing material systems spanning soft polymers to stiff ceramics including both isotropic and anisotropic responses. Inelastic behaviors including (visco)plasticity, damage, and fracture have all incorporated for use in various analyses. This multitude of options and flexibility, however, comes at the cost of many capabilities, features, and responses and the ensuing complexity in the resulting implementation. Therefore, to enhance confidence and enable the utilization of the LAMÉ library in application, this effort seeks to document and verify the various models in the LAMÉ library. Specifically, the broader strategy, organization, and interface of the library itself is first presented. The physical theory, numerical implementation, and user guide for a large set of models is then discussed. Importantly, a number of verification tests are performed with each model to not only have confidence in the model itself but also highlight some important response characteristics and features that may be of interest to end-users. Finally, in looking ahead to the future, approaches to add material models to this library and further expand the capabilities are presented.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Technical Documents for Gateway for Accelerated Innovation in Nuclear (GAIN)

The Gateway for Accelerated Innovation in Nuclear (GAIN) provides the nuclear energy community with access to the technical, regulatory, and financial support necessary to move new or advanced nuclear reactor designs toward commercialization. GAIN provides the nuclear community with a single point of access to the broad range of capabilities (i.e., people, facilities, materials, and data) across the U.S. Department of Energy (DOE) complex and its National Lab capabilities. The Fast Flux Test Facility (FFTF) is the most recent liquid metal reactor (LMR) to be designed, constructed, and operated by DOE. The 400-MWt sodium-cooled, fast-neutron flux reactor plant was designed for irradiation testing of nuclear reactor fuels and materials for liquid metal fast breeder reactors. Following the demise of the breeder reactor program in the United States, FFTF continued to play a key role in providing a test bed for demonstrating performance of advanced fuel designs and demonstrating operation, maintenance, and safety of advanced liquid metal reactors. The FFTF Program provides valuable information for potential follow-on reactor projects in the areas of plant system and component design, component fabrication, fuel design and performance, reactor control, prototype testing, and site construction. This report provides documents related to three important aspects of FFTF design and operation: 1) irradiation behavior of structural alloys and absorber materials, 2) thermohydraulics of rod bundles (i.e., coolant mixing), and 3) natural circulation heat transfer in the areas of modeling and validation. These technical documents are believed to be of interest to the nuclear industry and in particular to designers of new liquid metal reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Concentric Ring Gas Atomization Die Design for Optimized Particle Production

In partnership with Linde plc (formerly Praxair, Inc.), Ames Laboratory will further develop and commercialize its concentric-ring high pressure gas atomization (CR-HPGA) gas-die technology with a goal to improve the precision of metal powder production in a desired size range and quality. The successful commercialization of this technology could reduce production cost of metal powders and improve reliability of this industrial process, increasing specialty alloy powder availability for new applications and adoption into additive manufacturing and multiple materials sectors. The project scope is to [1] utilize AMES compressible gas flow and melt break-up models to explore a wide swath of parameter space available for the CR-HPGA technology, identifying the most promising gas-die designs for fabrication, [2] verify and optimize the new gas-die design, fabricate it and select preferred operating parameters by gas-only flow imaging and aspiration pressure measurements, down-selecting gas compositions and atomization parameters for full scale testing, [3] perform pilot-scale atomization trials with Al and/or Cu alloys of a new CR-HPGA gas-die at selected parameters, [4] evaluate gas-die performance by comparing resulting powder size distribution and powder quality attributes with equivalent powders made by conventional close-coupled HPGA technology, and [5] assess (through Praxair partnership) reduction in operational costs of new CR-HPGA gas-die through the use of an inert gas recovery/recycling system. In partnership with Praxair, Inc., the team, led by Ames Laboratory senior metallurgist Iver Anderson, intend to demonstrate the performance of an optimized CR-HPGA gas-die design in a pilot scale atomizer and better understand the design and operational controls to increase overall benefits for precision metal powder production.

42 ENGINEERING↗

DOE OSTI2023

Enabling Dark Energy Measurements from DESI and LSST (Final Technical Report)

This grant enabled efforts to lead the Survey Validation of the Luminous Red Galaxy (LRG) sample for DESI, entailing intensive work to prepare target samples, test their performance with DESI data, and validate that the requirements of the survey for this key sample are met. Luminous Red Galaxies represent the gold standard target class for Baryon Acoustic Observation experiments to study Dark Energy. It also funded work to co-leading the Follow-up Task Force within the LSST Dark Energy Science Collaboration (LSST DESC), which is intended to help develop collaborations with external groups and to produce cross-working group proposals for telescope time, policy proposals and white papers as needed in order to help the collaboration obtain and make use of complementary data which will strengthen LSST Dark Energy constraints. The PI has been particularly engaged in efforts to obtain access to spectroscopic training sets for LSST photometric redshifts in the first years of the survey, which requires developing relationships with groups that are obtaining such data for other purposes. This group has evolved into an External Synergies working group within DESC, also co-led by the PI. These groups have developed white papers for Astro2020, letters of intent and white papers for Snowmass2021, and a response to a DOE-NASA RFI. It also has enabled smaller contributions to improving LSST DESC pipeline infrastructure for photometric redshifts.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2022

Library of Advanced Materials for Engineering ((LAMÉ) 5.6

Accurate and efficient constitutive modeling remains a cornerstone issue for solid mechanics analysis. Over the years, the LAMÉ advanced material model library has grown to address this challenge by implementing models capable of describing material systems spanning soft polymers to stiff ceramics including both isotropic and anisotropic responses. Inelastic behaviors including (visco)plasticity, damage, and fracture have all incorporated for use in various analyses. This multitude of options and flexibility, however, comes at the cost of many capabilities, features, and responses and the ensuing complexity in the resulting implementation. Therefore, to enhance confidence and enable the utilization of the LAMÉ library in application, this effort seeks to document and verify the various models in the LAMÉ library. Specifically, the broader strategy, organization, and interface of the library itself is first presented. The physical theory, numerical implementation, and user guide for a large set of models is then discussed. Importantly, a number of verification tests are performed with each model to not only have confidence in the model itself but also highlight some important response characteristics and features that may be of interest to end-users. Finally, in looking ahead to the future, approaches to add material models to this library and further expand the capabilities are presented.

36 MATERIALS SCIENCE↗