Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance prediction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Further Development of the NASA X-57 Maxwell Mission Planning Tool for Mods II, III, and IV

The experimental, fully electric X-57 Maxwell is designed to enable lower energy con-sumption at cruise compare to a fuel burning baseline. This is to be achieved using a sumof subsystem benefits incorporated in the electric, airframe, and propulsion systems. AMission Planning Tool captures the three stages of X-57 development in order to assess thedesign of each subsystem in the context of the whole aircraft. The Mission Planning Toolfor the fully electric X-57 Maxwell captures the aerodynamics, propulsion, heat transfer,and power system of the aircraft with trajectory optimization capabilities. It is able tomodel these subsystems through all phases of flight, from taxi to landing. Through thismultidisciplinary approach, we are able to predict the benefit of each subsystem and theeffect of key design assumptions and how the aircraft will react if they are not met or ex-ceeded. As the aircraft progresses and systems are tested, we can use the Mission PlanningTool to continue to predict performance. This paper details the continued development ofthe X-57 Mission Planning Tool and demonstrates its capabilities.

trajectory↗
NASA NTRS2019

A Proposal for Standardized MMOD Shielding for Robotic Spacecraft

NASA robotic spacecraft are required to assess the potential for small debris induced failure for all disposal-critical components. Additional shielding might then be necessary in order to meet the acceptable risk requirement for the overall mission. Traditionally this requirement had been met with little or no additional shielding. Since the introduction of a high density debris population in ORDEM 3.0, some missions, especially those in higher portions of Low Earth Orbit, have needed additional MMOD-specific shielding in order for the mission to meet the requirement. This is a costly design effort when performed late in the project life cycle, which adds unexpected mass to the spacecraft components during the integration phase, and could disrupt thermal management.A proposal is discussed to develop a more cost-effective approach to MMOD-shielding, which can be employed earlier in the hardware design phase. The development and adoption of standardized shielding assemblies allows early tailoring of the shielding around a component, so that the mass is accounted for, as well as the small particle penetration risk, at a point in the design phase when the cost and schedule impact are more manageable. A set of several assemblies can be developed with a range of protection thresholds, in order to control mass where less shielding is needed. Such shielding assemblies would be developed in collaboration with blanket assembly specialists and thermal control engineers to ensure manufacturability and thermal performance challenges are known and acceptable. One clear benefit of such an approach is that hypervelocity testing can be performed on each of the standard shield assemblies to refine and confirm their performance prior to use.The challenges inherent in designing supplemental MMOD shielding will be discussed, including variations in the orbital debris environment and performance prediction. The benefits of a standardized shielding approach and example applications will also be presented.

Hull, Scott M.↗
NASA NTRS2019

A Proposal for Standardized MMOD Shielding for Robotic Spacecraft

NASA robotic spacecraft are required to assess the potential for small debris induced failure for all disposal-critical components. Additional shielding might then be necessary in order to meet the acceptable risk requirement for the overall mission. Traditionally this requirement had been met with little or no additional shielding. Since the introduction of a high density debris population in ORDEM 3.0, some missions, especially those in higher portions of Low Earth Orbit, have needed additional MMOD-specific shielding in order for the mission to meet the requirement. This is a costly design effort when performed late in the project life cycle, which adds unexpected mass to the spacecraft components during the integration phase, and could disrupt thermal management. A proposal is discussed to develop a more cost-effective approach to MMOD-shielding, which can be employed earlier in the hardware design phase. The development and adoption of standardized shielding assemblies allows early tailoring of the shielding around a component, so that the mass is accounted for, as well as the small particle penetration risk, at a point in the design phase when the cost and schedule impact are more manageable. A set of several assemblies can be developed with a range of protection thresholds, in order to control mass where less shielding is needed. Such shielding assemblies would be developed in collaboration with blanket assembly specialists and thermal control engineers to ensure manufacturability and thermal performance challenges are known and acceptable. One clear benefit of such an approach is that hypervelocity testing can be performed on each of the standard shield assemblies to refine and confirm their performance prior to use.The challenges inherent in designing supplemental MMOD shielding will be discussed, including variations in the orbital debris environment and performance prediction. The benefits of a standardized shielding approach and example applications will also be presented.

Hull, Scott M.↗
NASA NTRS2019

Microwave SQUID Multiplexing for the Lynx X-Ray Microcalorimeter

The Lynx x-ray microcalorimeter (LXM) is an imaging spectrometer for the Lynx satellite mission, an x-ray telescope being considered by NASA to be a new flagship mission. Lynx will enable unique astrophysical observations into the x-ray universe due to its high angular resolution and large field of view. The LXM consists of an array of over 100,000 pixels and poses a significant technological challenge to achieve the high degree of multiplexing required to read out these sensors. We discuss the details of microwave superconducting quantum interference device (SQUID) multiplexing and describe why it is ideally suited to the needs of the LXM. This case is made by summarizing the current and predicted performance of microwave SQUID multiplexing and describing the steps needed to optimize designs for all the LXM arrays. Finally, we describe our plan to advance the technology readiness level (TRL) of microwave SQUID multiplexing of the LXM microcalorimeters to TRL-5 by 2024.

Bennett, Douglas A.↗
NASA NTRSDate not supplied

RDE Nozzle Computational Design Methodology Development and Application

The Open National Combustion Code (OpenNCC) is used to simulate the aerospike exhaust nozzle region of a rotating detonation engine (RDE).The main objectives of the current study are twofold. The first goal is to validate the proposed computational methodology using the experimental data. The second goal is to demonstrate how the validated prediction tool can be used to optimize the nozzle geometry. To achieve a significant speed-up of computational time, the computational domain in divided into two parts: a combustion region and a throat-nozzle section. In the combustion region, a validated quasi-two-dimensional in-house code is utilized to generate an unsteady RDE flow field solution just upstream of the combustor throat. Subsequently, the unsteady flow data is fed into the three-dimensional throat-nozzle section as the inflow boundary condition. This facilitates the design optimization process since the unsteady inflow can be reused, and a relatively coarse mesh (i.e., larger time-step) can be used to analyze the flow fields around the nozzle. Five nozzle designs were studied and the predicted performance (i.e., thrust)compared. The optimized nozzle was found to produce 3.2% more overall thrust than a baseline nozzle design. Without the nozzle, there is a large low-pressure region at the throat exit, which significantly reduces the overall performance. This methodology is shown to be a promising approach to explore a wide variety of nozzle geometries in a relatively short amount of time.

CFD↗
NASA NTRS1996

Cassini Stellar Reference Unit: Performance Test Approach and Results

The Cassini Stellar Reference Unit (SRU) is the prime attitude determination sensor on the Cassini spacecraft...To ensure that the SRU will operate within specification for the entire mission, an extensive test program has been undertaken to characterize the SRU performance prior to launch and to quantify any expected performance degradation. Results from several eomplimentary test programs are presented and compared with pre-test performance predictions.

star↗
NASA NTRS2017

Characterization of the Teledyne CHROMA HgCdTe Detector for Imaging Spectrometers

Imaging spectroscopy places high demands upon detector performance. The dynamic range, linearity, and sensitivity must be maintained at high frame rates, and artifacts must be minimized across large focal plane array (FPA) formats. In this contribution, we discuss the Teledyne CHROMA HgCdTe FPA in the context of imaging spectrometer applications. The FPA was characterized in a laboratory thermal-vacuum chamber that allowed the read noise, dark current, well capacity, linearity, and crosstalk to be measured. Results are presented across a range of operating temperatures and pixel clock rates. Additionally, the outcomes of radiation testing to 100 krad TID are discussed. The results of these characterizations are critical to the designs and performance predictions of future imaging spectrometers utilizing the HgCdTe CHROMA FPA.

Green, Robert↗
NASA NTRS2017

LCRD Optical Ground Station 1

NASA’s Laser Communications Relay Demonstration (LCRD) will demonstrate and study bi-directional space-to-ground optical links. Optical Ground Station 1 (OGS-1) for LCRD will be developed at the Optical Communications Telescope Laboratory (OCTL), a 1-meter telescope in the San Gabriel Mountains northeast of the Jet Propulsion Laboratory. This paper will present an updated overview of OGS-1, its systems and capabilities, and its preparations for integrating and verifying readiness of the completed system. It will conclude with predicted performance of the OGS-1 system.

Piazzolla, Sabino↗
NASA NTRS2019

Thermal design of the sample handling assembly in the sampling and caching subsystem on the Mars 2020 rover

The Mars 2020 Rover is scheduled to land on Mars on February 18, 2021. One of the primary mission objectives for the Mars 2020 Rover is to collect a set of Martian regolith samples for potential future return to Earth. Regolith and rock samples will be collected and placed into sample tubes using a coring drill, located at the end of a large Robotic Arm, on the outside of the rover. Filled sample tubes will be transferred from the outside of the Rover into the Adaptive Caching Assembly (ACA), located inside the Rover chassis, via the Bit Carousel. Once the filled sample tube is brought into the ACA, the Sample Handling Assembly (SHA) will transfer it to all of the internal processing stations of the ACA for volume assessment, sealing and finally drop-off on the Martian surface. The ACA is a volume within the rover chassis that is not temperature-controlled. Actuators inside the SHA and its End Effector (EE) must be warmed to above -55°C and -25°C, respectively, prior to use. This paper discusses the thermal design of the SHA that uses heaters and temperature sensors to warm up and maintain the temperature-sensitive arm components within temperature limits during operation. Thermal performance predictions for Mars surface operations are also presented.

Lee, Chern-Jiin↗
NASA NTRSDate not supplied

Integral Velocity Sampling for Unsteady Rotor Models on Cartesian Meshes

An unsteady body-force rotor model utilizing integral velocity sampling is developed for Cartesian meshes with a focus on accurate performance predictions. In this approach, the rotors are modeled as body-force source terms, and integral sampling is used to define the local freestream velocity vector. The method is verified in two dimensions for airfoils, providing accurate angle of attack and freestream Mach number estimates even on relatively coarse meshes, and demonstrating excellent mesh convergence across a variety of source region thicknesses. Extensions of the model to three dimensions for both fixed and rotating wings are considered, with numerical experiments demonstrating the need for a spanwise-continuous representation of the induced velocity or angle of attack. The model provides reasonable spanwise lift distributions without any explicit tip-loss model. Comparisons to high-fidelity simulations and experimental data show excellent agreement for predictions of an isolated DJI Phantom 3 propeller in hover. Finally, simulations of the full aircraft in edgewise forward flight also compare well with wind tunnel data across a variety of pitch angles and propeller speeds.

ARMD↗
NASA NTRSDate not supplied

Scaling of Liquefaction Systems and the Effects of Gravity

Recent exploration initiatives both by NASA and others have produced interest in the liquefaction of fluids produced through in-situ processes on the surfaces of the Moon and Mars. Liquefaction of fluids in cryogenic temperatures is routinely done at large scale for terrestrial uses, but these processes do not necessarily scale down in an economical or technologically feasible manner for the anticipated rates of initial Lunar or Martian production plants. To understand appropriate processes and scaling parameters, various options should be considered. A multi-center team at NASA considered multiple different refrigeration cycles and refrigeration integration methodologies as well as how these might fit into early liquefaction plants. These studies resulted in the conclusion that integrating the tubing on the storage tank wall (for both structural and heat spreading reasons), preferably the tank which will actually use the fluid, is the nearest path forward. Given that assumption on the general framework of the liquefaction system, there are several different heat transfer mechanisms to consider from a scaling perspective. These include forced convection heat removal to the refrigeration system (or cryocooler), conduction through the tank wall heat exchanger, and condensation (with some natural convection) on the inner tank wall. Analysis of these mechanisms shows that while there is some sensitivity to gravitational level, that within the bounds of current interest (Lunar and Martian applications), this sensitivity does not dominate the liquefaction application. While there will be some effect, perhaps in a limiting manner as the tanks approach some high fill level, system level testing on the Earth should suffice for the performance prediction and demonstration of liquefaction operations as applicable to Lunar and Martian applications. However, as one approaches orbital conditions, this general approach to liquefaction will not be appropriate as the scaling of the heat transfer mechanisms is not appropriate. At this point, other approaches will need to be developed and demonstrated in the micro-gravity environment.

Cryogenics↗
NASA NTRSDate not supplied

Gravitational Effects on Liquefaction Systems for Lunar and Mars xploration

There is interest at NASA, other space agencies, and industry, in the liquefaction of fluids produced through in-situ processes on the surfaces of the Moon and Mars. A multi-center team at NASA recently considered multiple different refrigeration cycles and refrigeration integration methodologies and how these might fit into early liquefaction plants for NASA's exploration initiatives. The rate of liquefaction for these initiatives is quite slow in comparison to large scale terrestrial applications. These studies concluded that, for both structural and heat spreading reasons, integrating the refrigeration tubing on the surface of the storage tank wall is an attractive path to pursue in the near term. An analysis is performed of the condensation processes within the tank to determine the sensitivity of liquefaction to gravitational effects. The heat transfer mechanisms include forced convection heat removal to the refrigeration system (or cryocooler), conduction through the tank wall heat exchanger, and condensation on the inner tank wall. Gravity affects the liquefaction process via condensate liquid drainage, natural convection in the ullage, and the shape of the liquid-vapor interface in the tank. Analysis of these mechanisms shows that while there is some sensitivity to gravitational level in general, within the bounds of current interest (rate of liquefaction appropriate to Lunar and Martian applications), this sensitivity of liquefaction to gravity is quite small. Thus, system level testing on the Earth should suffice for the performance prediction and demonstration of liquefaction operations as applicable to lunar and Martian applications.

Cryogenics↗
NASA NTRSDate not supplied

Pretest Comprehensive Analysis for the Urban Air Mobility Side-by-Side Test Stand

The Urban Air Mobility (UAM) Side-by-Side Test Stand (SBS) is a two-rotor test stand designed and built at NASA Ames Research Center under the Revolutionary Vertical Lift Technology (RVLT) Project. The SBS entered service in the wind tunnel in the latter part of 2021 and allows for the experimental analysis of rotor-rotor interactions for UAM vehicles of the side-by-side variety. The SBS will allow investigation of the effect of numerous variables such as rotor lateral separation, rotor collective pitch, model pitch angle (𝛼), rotor rotation direction, and flight speed. This paper presents performance predictions for the SBS. These predictions, which were generated using CAMRAD II, provided increased assurance of the safe operational limits of the system. Additionally, these results, when compared with future data, will be used for validation of the computational models.

Comprehensive Analysis↗
NASA NTRS2020

Recent Developments in Tolerancing Methods for Imaging Spectrometers

We discuss detailed tolerancing methods developed for imaging spectrometers at NASA Jet Propulsion Laboratory, California Institute of Technology using the Earth Surface Mineral Dust Source Investigation (EMIT) imaging spectrometer as an illustrative example. We tolerance five metrics simultaneously: along-track response function, cross-track response function, spectral response function, spectral centroid uniformity, and spatial centroid uniformity. A method to calculate tolerancing sensitivities for each metric directly, a method to statistically combine Monte Carlo files from multiple tolerancing runs, and an example summary error budgets that communicate the key and driving tolerances for each metric are discussed. These methods facilitate rapid and semi-automated assessment of the predicted performance of imaging spectrometer systems from design through to assembly and launch life cycle, using metrics that are directly relevant to the extraction of accurate spectroscopic data from these instruments.

Mouroulis, Pantazis↗
NASA NTRS2020

Roman Space Telescope Coronagraph Engineering Design and Operating Concept

NASA’s Nancy Grace Roman Space Telescope (formerly known as WFIRST) is a flagship astrophysics mission planned for launch in 2025. The coronagraph instrument (CGI) on Roman will demonstrate the technology for direct imaging and spectroscopy of exoplanets around nearby stars. It will work with the obscured 2.4 meter diameter telescope and demonstrate starlight suppression that is up to 3 orders of magnitude deeper than the preceding space-based and ground-based coronagraphs by using active wavefront control in space with deformable mirrors. CGI has passed its Preliminary Design Review (PDR) in September 2019 and is working toward the instrument Critical Design Review (CDR) in the spring of 2021. We will describe the flow down of key and driving CGI requirements from high level performance to the instrument hardware and software, current instrument configuration and engineering design, operational concept planned for CGI observations, integrated modeling status, and performance predictions.

Tanga, Hong↗
NASA NTRS2022

Gravitational Effects on Liquefaction Systems for Lunar and Mars Exploration

There is interest at NASA, other space agencies, and industry, in the liquefaction of fluids produced through in-situ processes on the surfaces of the Moon and Mars. A multi-center team at NASA recently considered multiple different refrigeration cycles and refrigeration integration methodologies and how these might fit into early liquefaction plants for NASA's exploration initiatives. The rate of liquefaction for these initiatives is quite slow in comparison to large scale terrestrial applications. These studies concluded that, for both structural and heat spreading reasons, integrating the refrigeration tubing on the surface of the storage tank wall is an attractive path to pursue in the near term. In order to develop a technology development path and inform investors, it was desired to investigate the sensitivity of gravity of the processes involved. An analysis of the condensation processes within the tank is performed. The objective is to determine the sensitivity of liquefaction to gravitational effects. The heat transfer mechanisms include forced convection heat removal to the refrigeration system (or cryocooler), conduction through the tank wall heat exchanger, and convection and condensation on the inner tank wall. Gravity affects the liquefaction process via condensate liquid drainage, natural convection in the ullage, and the shape of the liquid-vapor interface within the tank. Analysis of these mechanisms shows that while there is some sensitivity to gravitational level in general, within the bounds of current interest (rate of liquefaction appropriate to Lunar and Martian applications, and cooling capacity of the cryocooler), this sensitivity of liquefaction to gravity is quite small. Thus, system level testing on the Earth should suffice for the performance prediction and demonstration of liquefaction operations as applicable to Lunar and Martian applications.

ISRU↗
NASA NTRS2021

Maximizing Dust Devil Follow-up Observations on Mars Using Cubesats and On-board Scheduling

Several million dust devil events occur on Mars every day. These events last, on average, about 30 minutes and range in size from meters to hundreds of meters in diameter. Designing low-cost missions that will improve our knowledge of dust devil formation and evolution, and their connection to atmospheric dynamics and the dust cycle, is fundamental to informing future crewed Mars lander missions about surface conditions. In this paper we present a mission for a constellation of low orbiting Mars cubesats, each carrying imagers with agile pointing capabilities. The goal is to maximize the number of dust devil follow-up observations through real-time, on-board scheduling. We study scenarios where cubesats are equipped with a 2.5 degree boresight angle camera that accommodates five slew positions (including nadir). We assume a concept of operations where the cubesats autonomously survey the surface of Mars and can autonomously detect dust devils from their surface imagery. When a dust devil is detected, the constellation is autonomously re-tasked through an on-board distributed scheduler to capture as many follow-on images of the event as possible, so as to study its evolution. The cubesat orbits are propagated assuming two-body dynamics and the ground tracks and camera field of view are computed assuming a spherical Mars. Realistic inter-agent communication link opportunities are computed and included in our optimization, which allow for real-time event detection information to be shared within the constellation. We compare against a powerful ``omniscient'' mission which has a priori knowledge of all dust devil activity to show the gap between predicted performance and the best possible outcome. In particular, we show that the communications are especially important for acquiring follow-up observations, and that a realistic distributed scheduling mechanism is sufficient to capture nearly all dust devil observations that are possible for a given orbit configuration.

Hook, Joshua Vander↗