Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “morphological”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Mechanism for atmosphere dependence of laser damage morphology in HfO{sub 2}/SiO{sub 2} high reflective films

We show in this paper single-shot and multi-shot laser-induced damage thresholds (LIDTs) of HfO{sub 2}/SiO{sub 2} high reflective films (the reflectance = 99.9%) are affected by the presence of a water layer absorbed on the surface of the porous films. When the water layer was removed with the process of pumping, the single-shot LIDT measured in vacuum dropped to {approx}48% of that measured in air, while the multi-shot LIDT in vacuum dropped to {approx}47% of its atmospheric value for the high reflective films. Typical damage micrographs of the films in air and in vacuum were obtained, showing distinct damage morphologies. Such atmosphere dependence of the laser damage morphology was found to originate from that formation of a water layer on the surface of porous films could cause an increase of horizontal thermal conductivity and a reduction of vertical thermal conductivity. Moreover, laser-induced periodic ripple damages in air were found in the SiO{sub 2} layer from the micrographs. A model of deformation kinematics was used to illustrate the occurrence of the periodic ripple damage, showing that it could be attributed to a contraction of the HfO{sub 2} layer under irradiation by the 5-ns laser pulses in air.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The mechanism of the surface morphology transformation for the carbon nanotube thin film irradiated via excimer laser

In this paper, the surface morphology transformation of the sprayed carbon nanotube (CNT) thin film irradiated with the excimer laser has been systematically investigated. Under the excimer-laser irradiation, two phenomena, including the annealing and ablation effects, were found to be dependent on the incident laser energy and overlapping ratios. Moreover, the extremely high protrusions would be produced in the interface between the annealing and ablation regions. The mechanism of the CNT thin film under the excimer laser irradiation was, therefore, proposed to derive the surface morphology modifications and the further reinforced crystallinity with proper laser energy densities and overlapping ratios.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Cellulose nanocrystal from pomelo (C. Grandis osbeck) albedo: Chemical, morphology and crystallinity evaluation

Citrus peel is one of the under-utilized waste materials that have potential in producing a valuable fibre, which are cellulose and cellulose nanocrystal. Cellulose was first isolated from pomelo (C. Grandis Osbeck) albedo by combination of alkali treatment and bleaching process, followed by acid hydrolysis (65% H{sub 2}SO{sub 4}, 45 °C, 45min) to produce cellulose nanocrystal. The crystalline, structural, morphological and chemical properties of both materials were studied. Result reveals the crystallinity index obtained from X-ray diffraction for cellulose nanocrystal was found higher than extracted cellulose with the value of 60.27% and 57.47%, respectively. Fourier transform infrared showed that the chemical treatments removed most of the hemicellulose and lignin from the pomelo albedo fibre. This has been confirmed further by SEM and TEM for their morphological studies. These results showed that cellulose and cellulose nanocrystal were successfully obtained from pomelo albedo and might be potentially used in producing functional fibres for food application.

60 APPLIED LIFE SCIENCES↗

Role of sonic energy on growth morphology and optical properties of ZnO:S nanostructures

ZnO nanopowders doped with sulphur were prepared by sonochemical method. The input power of ultrasound was varied as 40%, 50% and 60% of the maximum power (375 W) in both continuous and pulsed mode. XRD results show the average size of the nanoparticles is the least for those prepared with 50% input power as well as the micro-strain. FESEM studies showed the formation of nanorods clubbed together to form flower like structure for these samples. In rest of the cases, no definite morphology was obtained. High resolution transmission electron microscopy (HRTEM) reveals the formation of nanorods oriented along c-axis for those samples prepared with 50% input power. No cavitation at 40% and excessive dissolution at 60% may lead to this type of morphology. Absorption studies showed high absorbance for sulphur doped samples but this was highest for the samples prepared with 60% input power.

36 MATERIALS SCIENCE↗

Effect of ZnO seed layer on the morphology and optical properties of ZnO nanorods grown on GaN buffer layers

ZnO nanorods were grown by chemical bath deposition on sputtered, polycrystalline GaN buffer layers with and without ZnO seed layer. Scanning electron microscopy and X-ray diffraction show that the ZnO nanorods on GaN buffer layers are not vertically well aligned. Photoluminescence spectrum of ZnO nanorods grown on GaN buffer layer, however exhibits a much stronger near-band-edge emission and negligible defect emission, compared to the nanorods grown on ZnO buffer layer. These features are attributed to gallium incorporation at the ZnO-GaN interface. The introduction of a thin (25 nm) ZnO seed layer on GaN buffer layer significantly improves the morphology and vertical alignment of ZnO-NRs without sacrificing the high optical quality of ZnO nanorods on GaN buffer layer. The presence of a thick (200 nm) ZnO seed layer completely masks the effect of the underlying GaN buffer layer on the morphology and optical properties of nanorods.

36 MATERIALS SCIENCE↗

Surface diffusion driven morphological instability in free-standing nickel nanorod arrays

Metallic nanostructures are thermodynamically unstable due to the excess of energy of large numbers of surface atoms. Morphological instability, such as Rayleigh breakup, sintering, and coalescence, can be observed at a temperature much lower than the bulk melting point of the metal. We study the morphological and crystalline evolution of well-aligned free-standing nickel nanorod arrays at elevated temperatures up to 600 °C. The as-deposited nickel nanorods are faceted with sharp nanotips, which are deformed at annealing temperatures higher than 400 °C due to strong surface diffusion. A mud-crack like pattern is formed in the samples annealed above 400 °C, leading to the generation of interconnected porous structure. Meanwhile, the X-ray diffraction reveals the recrystallization of nickel nanocrystals when annealed from 300 to 600 °C.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Impact of annealing on the chemical structure and morphology of the thin-film CdTe/ZnO interface

To enable an understanding and optimization of the optoelectronic behavior of CdTe-ZnO nanocomposites, the morphological and chemical properties of annealed CdTe/ZnO interface structures were studied. For that purpose, CdTe layers of varying thickness (4–24 nm) were sputter-deposited on 100 nm-thick ZnO films on surface-oxidized Si(100) substrates. The morphological and chemical effects of annealing at 525 °C were investigated using X-ray Photoelectron Spectroscopy (XPS), X-ray-excited Auger electron spectroscopy, energy dispersive X-ray spectroscopy, scanning electron microscopy, and atomic force microscopy. We find a decrease of the Cd and Te surface concentration after annealing, parallel to an increase in Zn and O signals. While the as-deposited film surfaces show small grains (100 nm diameter) of CdTe on the ZnO surface, annealing induces a significant growth of these grains and separation into islands (with diameters as large as 1 μm). The compositional change at the surface is more pronounced for Cd than for Te, as evidenced using component peak fitting of the Cd and Te 3d XPS peaks. The modified Auger parameters of Cd and Te are also calculated to further elucidate the local chemical environment before and after annealing. Together, these results suggest the formation of tellurium and cadmium oxide species at the CdTe/ZnO interface upon annealing, which can create a barrier for charge carrier transport, and might allow for a deliberate modification of interface properties with suitably chosen thermal treatment parameters.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of annealing on the growth dynamics of ZnPc LB thin film and its surface morphology

The ZnPc molecules in the thin film prepared by Langmuir-Blodgett (LB) process in asdeposited state has been found to have an edge on orientation with average tilt angle of 64.3 ° as confirmed from the Pressure-Area (π-A) isotherm and X-ray diffraction (XRD) study. The ZnPc LB thin film has been observed to have abnormal growth mode at higher annealing temperature and it is mainly driven by minimization of surface free energy which lead to large increase in crystallinity of the film. Kinetically favored orientational and structural transitions of ZnPc thin film during annealing and their effect on the surface morphology of the thin film has been studied using scaling concepts. The scaling exponents 1) root mean square (RMS) roughness σ, 2) roughness exponent α and, 3) in plane correlation length ξ are calculated from the HDCF g(r) and ACF C(r). The RMS surface roughness σ is found to be dependent on the as defined short wavelength undulations (ρ) and long wavelength undulations (χ). Both ρ and χ are the function of all the three scaling exponents. σ has been observed to be maximum for the ZnPc thin film annealed at 290 °C, since the χ shoot to maximum value at this temperature due to the formation of small domains of ZnPc nanorods. The self affinity of the ZnPc thin film is found to decrease on annealing as obtained from both power spectral density (PSD) and HDCF g(R) and ACF C(R) study, which confirms that the dimension of surface morphology of the ZnPc LB thin film transform towards 2D with increase in annealing temperature.

36 MATERIALS SCIENCE↗

InGaN: Direct correlation of nanoscopic morphology features with optical and structural properties

A comprehensive study on the impact of growth modes on the structural and optical properties of thick InGaN layers suitable for photovoltaic application is presented. Samples grown by metalorganic vapour phase epitaxy with different growth rates and thicknesses have been analyzed. The application of slow growth rates result in smooth layers while higher growth rates induce a meandering surface morphology. Using low-temperature cathodoluminescence, a direct correlation of the morphology to local luminescent properties is obtained: the top of meandering structures reveals a spectrally red-shifted emission compared to the emission wavelength expected from the average indium content determined by X-ray diffraction. The origin of this shift is identified and explained by increased indium incorporation on top of the meander due to a spatially localized compositional pulling effect.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Communication: Non-Hadwiger terms in morphological thermodynamics of fluids

We demonstrate that the Hadwiger form of the free energy of a fluid in contact with a wall is insufficient to describe the low-density behavior of a hard-sphere fluid. This implies that morphological thermodynamics of the hard-sphere fluid is an approximate theory if only four geometric measures are included. In order to quantify deviations from the Hadwiger form we extend standard fundamental measure theory of the bulk fluid by introducing additional scaled-particle variables which allow for the description of non-Hadwiger coefficients. The theory is in excellent agreement with recent computer simulations. The fact that the leading non-Hadwiger coefficient is one order of magnitude smaller than the smallest Hadwiger coefficient lends confidence to the numerous results that have been previously obtained within standard morphological thermodynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Dielectric Breakdown Model applied to explain various morphologies of deposited metallic structures in thin gap metal electro-deposition

The phenomenon of metal electro-deposition in thin-gap geometry leads to very interesting and diverse two dimensional morphologies. This varies from dense ramified growth to thin dendritic projections. In this paper, we have proposed a stochastic model that incorporates such diversity. We carried out thin-gap electro-deposition of Copper and Zinc with varying electrolytic concentrations. A well known model, that until this work was used to explain dielectric breakdown patterns, was employed to explain the variation in deposition morphology with concentration. The sole parameter in the model was varied and the numerically obtained patterns was seen to correlate well with those obtained from electro-deposition. A linear relationship between the parameter and molar concentration was established. The established relationship was then analysed and interpreted.

36 MATERIALS SCIENCE↗

Morphological impact on the reaction kinetics of size-selected cobalt oxide nanoparticles

Apart from large surface areas, low activation energies are essential for efficient reactions, particularly in heterogeneous catalysis. Here, we show that not only the size of nanoparticles but also their detailed morphology can crucially affect reaction kinetics, as demonstrated for mass-selected, soft-landed, and oxidized cobalt clusters in a 6 nm to 18 nm size range. The method of reflection high-energy electron diffraction is extended to the quantitative determination of particle activation energies which is applied for repeated oxidation and reduction cycles at the same particles. We find unexpectedly small activation barriers for the reduction reaction of the largest particles studied, despite generally increasing barriers for growing sizes. We attribute these observations to the interplay of reaction-specific material transport with a size-dependent inner particle morphology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optical and morphological characterizations of pyronin dye-poly (vinyl alcohol) thin films formed on glass substrates

Thin films of pyronin dye mixed with poly(vinyl alcohol) (PVA) on glass substrate were prepared by using spin-coating technique. The optical and morphological properties of the thin films were studied by UV-Vis., steady-state fluorescence spectroscopies and atomic force microscopy (AFM). The thin films on glass substrate were fabricated at various [PVA]/[dye] (P/D) ratios. Hence, the monomeric and H-aggregates thin films of pyronin dye mixed with PVA were formed as a function of the dye and PVA concentration. It was determined that while the monomeric thin films showed strong fluorescence, the formation of H-aggregates in the thin film caused to decreasing the fluorescence intensity. AFM studies demonstrated that the morphology of the thin film was drastically varied with changing the optical property of the thin film such as monomeric and H-aggregates thin films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural and morphological modifications of polymer thin film in the presence of nonsolvent

Thin films of sodium poly(acrylic acid) salt (Na-PAA) have been investigated to obtain the modification of the out-of-plane structure and surface morphology in the presence of toluene which is considered as nonsolvent for Na-PAA. X-ray reflectivity analysis show that the out-of-plane thickness of the Na-PAA film increases if the film is kept for longer time inside the toluene. For the thicker film the effect of toluene is more pronounced than the thinner one. Surface morphology obtained from the atomic force microscopy shows that the top surface becomes relatively rough after the dipping of the Na-PAA film inside toluene. Although toluene is nonsolvent for Na-PAA molecules, however, the effect of restructuring of the nanometer-thick polymer film cannot be ignored. The reason for such structural modification has been proposed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of bath temperature on structure, morphology and thermoelectric properties of CoSb{sub 3} thin films

CoSb{sub 3} thin films are deposited on conducting glass substrates (FTO) by electrodeposition at different bath temperatures (60°C, 70°C and 80°C) and the resulting influence of the bath temperature on the structure, morphology and electrical properties of films is investigated. X-ray diffraction confirms the formation of CoSb{sub 3} phase in the films. Scanning electron microscopy reveals that different morphologies ranging from branched nano-flakes to nano-needles evolve as bath temperature increases. It is concluded that a growth temperature of 80°C is suitable for producing CoSb{sub 3} films with such properties that show potential feasibility for thermoelectric applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A study on different morphological structures of zinc oxide nanostructures for humidity sensing application

Effects of different morphological structures of ZnO to the performance of the device in the humidity sensing have been studied. Two different kinds of nanostructures were obtained which are nanords and nanoflakes. From the surface morphology image, the ZnO nanoflakes has lower diameter size of 100 nm compared to ZnO nanorods of 250 nm. The ZnO nanoflakes are not aligned and has low porous structure compared to ZnO nanorods. The humidity sensor performance of ZnO nanorods has superior performance compared to ZnO nanoflakes. The sensitivity of the ZnO nanorods sensor is 3.20 which are almost two times higher than the ZnO nanoflakes of 1.65. The structural properties of the samples have been characterized using field emission scanning electron microscopy (FESEM) electrical properties has been characterized using current voltage (I-V) measurement.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Morphology and proton diffusion in a coarse-grained model of sulfonated poly(phenylenes)

A coarse-grained model previously used to simulate Nafion using dissipative particle dynamics (DPD) is modified to describe sulfonated Diels-Alder poly(phenylene) (SDAPP) polymers. The model includes a proton-hopping mechanism similar to the Grotthuss mechanism. The intramolecular parameters for SDAPP are derived from atomistic molecular dynamics (MD) simulation using the iterative Boltzmann inversion. The polymer radii of gyration, domain morphologies, and cluster distributions obtained from our DPD model are in good agreement with previous atomistic MD simulations. As found in the atomistic simulations, the DPD simulations predict that the SDAPP nanophase separates into hydrophobic polymer domains and hydrophilic domains that percolate through the system at sufficiently high sulfonation and hydration levels. Increasing sulfonation and/or hydration leads to larger proton and water diffusion constants, in agreement with experimental measurements in SDAPP. In the DPD simulations, the proton hopping (Grotthuss) mechanism becomes important as sulfonation and hydration increase, in qualitative agreement with experiment. The turning on of the hopping mechanism also roughly correlates with the point at which the DPD simulations exhibit clear percolated, hydrophilic domains, demonstrating the important effects of morphology on proton transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Morphology and reactivity of size-selected titanium oxide nanoclusters on Au(111)

The morphology and reactivity of mass-selected titania clusters, Ti 3 O 6 and Ti 3 O 5 , deposited onto Au(111) were studied by scanning tunneling microscopy (STM) and temperature programmed desorption (TPD). Despite differing by only one oxygen atom, the stoichiometric Ti 3 O 6 and the sub-stoichiometric (“reduced”) Ti 3 O 5 clusters exhibit very different structures and preferred binding sites. The Ti 3 O 6 clusters preferentially bind at step edges and form small assemblies (2-4 clusters) on Au terraces, while the “reduced” Ti 3 O 5 clusters form much larger fractal-like assemblies that can extend across step boundaries. Annealing the Ti 3 O 5,6 /Au(111) systems to higher temperatures causes changes in the size-distributions of cluster assemblies but does not lead to the formation of TiO x nanoislands for temperatures ≤ 700 K. Reactivity studies show that the reduced Ti 3 O 5 cluster has higher activity than Ti 3 O 6 for 2-propanol dehydration, although both clusters exhibit substantial activity for dehydrogenation to acetone. Calculations using DFT+U suggest that the differences in aggregate morphology and reactivity are associated with the number of undercoordinated Ti 3c sites in the supported clusters.

36 MATERIALS SCIENCE↗