Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Amino acids as performance-controlling additives in carbonation-activated cementitious materials

This article presents an investigation on the application of amino acids to control the CaCO{sub 3} crystallization in carbonation cured wollastonite composites. It was observed that wollastonite carbonated without any amino acid formed calcite as the primary polymorph of CaCO{sub 3}. In contrast, the use of amino acids as admixtures resulted in the formation of stable amorphous calcium carbonate (ACC), vaterite, and aragonite during the carbonation of wollastonite. The carbonated composites produced with amino acids were observed to have a lower critical pore size, but a higher total porosity, compared to the control batch. Additionally, the utilization of amino acids was observed to increase the flexural strength and compressive strength of the composites up to 106% and 48%, respectively, compared to the control batch. Such performance enhancement of the carbonated composites in the presence of amino acids was attributed to the reduced critical pore size and the formation of organic-inorganic hybrid phases in the matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Carrier Diffusion Lengths in Continuously Grown and Etched-and-Regrown GaN Pin Diodes

Advanced GaN power devices are promising for many applications in high power electronics but performance limitations due to material quality in etched-and-regrown junctions prevent their widespread use. Carrier diffusion length is a critical parameter that not only determines device performance but is also a diagnostic of material quality. Here we present the use of electron-beam induced current to measure carrier diffusion lengths in continuously grown and etched-and-regrown GaN pin diodes as models for interfaces in more complex devices. Variations in the quality of the etched-and-regrown junctions are observed and shown to be due to the degradation of the n-type material. Finally, we observe an etched-and-regrown junction with properties comparable to a continuously grown junction.

42 ENGINEERING↗
DOE OSTI2022

Direct visualization of polaron formation in the thermoelectric SnSe

SnSe is a layered material that currently holds the record for bulk thermoelectric efficiency. The primary determinant of this high efficiency is thought to be the anomalously low thermal conductivity resulting from strong anharmonic coupling within the phonon system. Here we show that the nature of the carrier system in SnSe is also determined by strong coupling to phonons by directly visualizing polaron formation in the material. We employ ultrafast electron diffraction and diffuse scattering to track the response of phonons in both momentum and time to the photodoping of free carriers across the bandgap, observing the bimodal and anisotropic lattice distortions that drive carrier localization. Relatively large (18.7 Å), quasi-one-dimensional (1D) polarons are formed on the 300-fs timescale with smaller (4.2 Å) 3D polarons taking an order of magnitude longer (4 ps) to form. This difference appears to be a consequence of the profoundly anisotropic electron–phonon coupling in SnSe, with strong Fröhlich coupling only to zone-center polar optical phonons. These results demonstrate a high density of polarons in SnSe at optimal doping levels. Strong electron-phonon coupling is critical to the thermoelectric performance of this benchmark material and, potentially, high performance thermoelectrics more generally.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Protonic Ceramic Electrochemical Cells for Synthesizing Sustainable Chemicals and Fuels

Abstract Protonic ceramic electrochemical cells (PCECs) have been intensively studied as the technology that can be employed for power generation, energy storage, and sustainable chemical synthesis. Recently, there have been substantial advances in electrolyte and electrode materials for improving the performance of protonic ceramic fuel cells and protonic ceramic electrolyzers. However, the electrocatalytic materials development for synthesizing chemicals in PCECs has gained less attention, and there is a lack of systematic and fundamental understanding of the PCEC reactor design, reaction mechanisms, and electrode materials. This review comprehensively summarizes and critically evaluates the most up‐to‐date progress in employing PCECs to synthesize a wide range of chemicals, including ammonia, carbon monoxide, methane, light olefins, and aromatics. Factors that impact the conversion, selectivity, product yield, and energy efficiencies are discussed to provide new insights into designing electrochemical cells, developing electrode materials, and achieving economically viable chemical synthesis. The primary challenges associated with producing chemicals in PCECs are highlighted. Approaches to tackle these challenges are then offered, with a particular focus on deliberately designing electrode materials, aiming to achieve practically valuable product yield and energy efficiency. Finally, perspectives on the future development of PCECs for synthesizing sustainable chemicals are provided.

03 NATURAL GAS↗
DOE OSTI2020

Autonomous Strategies for Improved Performance and Reliability of Li‐Ion Batteries

Abstract The battery community has devoted significant effort to improve the performance and reliability of Li‐ion batteries through the development of new materials. The integration of autonomous function provides an alternative strategy to further extend performance. Autonomous material systems mimic the ability of biological systems to self‐protect, sense, regulate, and heal in response to damage and other environmental changes. When incorporated in batteries, these materials enable autonomic restoration of battery performance upon degradation, as well as autonomic shutdown or extinguishment in response to thermal runaway. Successful strategies for improving Li‐ion battery performance include controlled release of microencapsulated functional additives and the integration of self‐healing or adaptive interlayers and binders. These methods have been effective for stabilizing the solid electrolyte interface, preventing battery fires, restoring electrode conductivity, and suppressing Li dendrite growth. Challenges and opportunities exist in the further application of autonomous strategies in the battery environment. A greater variety of encapsulated additives with precise triggered‐release are needed to address specific battery degradation mechanisms. Incorporation of self‐healing polymers in solid‐state batteries facilitates improvement in interfacial and mechanical stability. The integration of autonomous strategies with battery management systems potentially enables enhanced control over multiple battery cycling parameters.

Zhao, Lihong↗
DOE OSTI2022

Ultra-fast and Thick Boriding of Geothermal Casing to Enhance Reliability

Harnessing the heat that is continuously generated underneath the Earth’s crust (geothermal) is a clean and renewable source of energy. Geothermal energy can be used to heat and cool buildings, including greenhouses, and to generate electrical power. Compared to other renewable energy sources such as solar and wind, geothermal energy is more reliable because it is available all the time and versatile in its many forms of application and deployment. Nonetheless, the deployment and extensive use of geothermal energy still lags behind other renewable sources due to some technical, but mainly economic challenges. Upfront costs of geothermal power well development are relatively high. Some of this high cost is attributed to the use of expensive construction materials to ensure adequate performance during operation. For example, Inconel 625, super duplex 2507, and titanium alloy materials are used in downhole casings, piping, and other components exposed to brine solution to withstand harsh operating environments (high temperature and corrosive environments). Relatively low-cost carbon steel can be used in many of these components in geothermal power plants; however, they are susceptible to excessive corrosion, thereby limiting their useful lifespan. Ultra-fast boriding (UFB) surface treatment of carbon steel may drastically increase its corrosion resistance thereby providing a cost-effective material solution in geothermal applications. Scientists at Argonne National Laboratory (ANL) recently developed a technique to accelerate the boriding process using a high-temperature electrochemical process to produce relatively thick boride layers on various metal and alloy materials in minutes rather than the several hours it takes through the typical pack boriding process; hence, the process is designated UFB. The process uses molten borax salt at 900– 1000°C in an electrochemical cell in which the material to be borided is the cathode and a graphite plate is the anode. Continuous and durable boride layers with thicknesses of 100–300 µm have been produced on a variety of metals and alloys in one hour. Such a surface layer can indeed be a cost-effective pathway to prevent corrosion of casing materials in contact with the chemically aggressive and corrosive geothermal brine fluids.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Application of Machine Learning to Assist a Moisture Durability Tool

The design of moisture-durable building enclosures is complicated by the number of materials, exposure conditions, and performance requirements. Hygrothermal simulations are used to assess moisture durability, but these require in-depth knowledge to be properly implemented. Machine learning (ML) offers the opportunity to simplify the design process by eliminating the need to carry out hygrothermal simulations. ML was used to assess the moisture durability of a building enclosure design and simplify the design process. This work used ML to predict the mold index and maximum moisture content of layers in typical residential wall constructions. Results show that ML, within the constraints of the construction, including exposure conditions, does an excellent job in predicting performance compared to hygrothermal simulations with a coefficient of determination, R2, over 0.90. Furthermore, the results indicate that the material properties of the vapor barrier and continuous insulation layer are strongly correlated to performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Alkyl-Substituted Polycaprolactone Poly(urethane-urea)s as Mechanically Competitive and Chemically Recyclable Materials

We report the mechanical performance and chemical recycling advantages of implementing alkyl-substituted poly(ε-caprolactones) (PCLs) as soft segments in thermoplastic poly(urethane-urea) (TPUU) materials. Poly(4-methylcaprolactone) (P4MCL) and poly(4-propylcaprolactone) (P4PrCL) were prepared, reacted with isophorone diisocyanate, and chain-extended with water to form TPUUs. The resulting materials’ tensile properties were similar or superior to a commercially available polyester thermoplastic poly(urethane) and had superior elastic recovery properties compared to a PCL analogue due to the noncrystalline nature of P4MCL and P4PrCL. Additionally, monomers were recovered from the TPUU materials in high yields via ring-closing depolymerization using a reactive distillation approach at an elevated temperature and a reduced pressure (240–260 °C, 25–140 mTorr) with zinc chloride (ZnCl 2 ) as the catalyst. The thermodynamics of polymerization were estimated using Van’t Hoff analyses for 4MCL and 4PrCL; these results indicated that the propyl group in 4PrCL results in a lower practical ceiling temperature (T c ) for P4PrCL.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Modeling Interfaces to Support Low-Level Waste Disposal System Performance Assessments - 20366

In low-level waste (LLW) disposal sites, interfaces between cementitious materials, used as waste forms and/or engineered barriers, and the surrounding soil or backfill material are often encountered. Reactions across these interfaces may lead to chemical and structural alteration of the cementitious and backfill materials that may ultimately affect long-term performance. For example, the ingress of carbon dioxide from soil gas into a waste tank concrete shell at the Hanford Site or Savannah River Site (SRS) or a low-level waste disposal vault at SRS leads to carbonation of cement hydration products (e.g. portlandite, calcium-silicate hydrate or C-S-H, and ettringite). The result of carbonation is a decrease in pH in the cement paste portion of the tank wall or vault concrete structure that could ultimately lead to de-passivation of the embedded structural steel and, eventually, to cracking. Cracking can lead to increased ingress of water into the structure, corresponding increased release of constituents of concern, and to subsequent increased transport of these constituents to the surrounding environment. The mobility of trace constituents (e.g., radionuclides of concern) in waste forms may increase in response to changes in pH, pore structure, and mineralogical gradients. Depletion of portlandite results in subsequent decalcification of C-S-H that leads to changes in the cement strength and may lead to structural failure. At the boundary between waste forms and concrete vaults, the migration of sulfate ions from the salt waste form (e.g., the saltstone waste form used for LLW disposal at the Savannah River Site in Saltstone Disposal Units, or SDUs) into the barrier or vault concrete has been predicted to result in expansive mineral phase formation (or 'sulfate attack'). Expansive mineral formation could result in cracking and potential loss of structural integrity in the vault concrete. In the performance assessment (PA) for the SRS SDUs, prediction of both the carbonation and sulfate attack fronts are critical to assessing the long-term performance of these LLW disposal vaults. A general purpose geochemical reactive transport model has been developed in LeachXS/ORCHESTRA to evaluate typical interfaces for LLW disposal environments, including SDUs at SRS. The model may be used to predict the long-term performance of interfaces between cementitious materials and saltstone or backfill materials with respect to primary phases by considering mass transport, cement chemistry, geochemical speciation, and multi-ionic diffusion over interfaces between different materials. The present study compares the performance and interactions between vault concrete and saltstone waste form for a representative SDU scenario. The materials were characterized using pH-dependence leaching test (EPA 1313) and semi-dynamic transport tests (EPA 1315) with test results used to parameterize the interface model. The development of a credible inter model provides an important basis for supporting future PAs where carbonation and sulfate attack are important aging and degradation mechanisms. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Nano Filters for Selective Metal Capture (CRADA Final Report)

As part of the Cyclotron Road program, Sunchem investigated novel nanoporous materials and their metal extraction performance in both batch and dynamic continuous flow operations. The proposed project developed novel nanoporous materials for selective metal extraction from complex industrial mixtures. The technical objectives were to synthesize and characterize the nanoporous materials, structure the nanoporous materials with binders along with structuring techniques and evaluate its performance in both a batch and dynamic continuous flow operation. The nanoporous material was structured through a disc granulation method to obtain particles in the size range of 250 to 500 micron diameter. This structured material was packed into a continuous flow column which achieved up to 48 wt% of gold capture. This work aimed to address the key technical risk of the materials’ capability to be employed in an industrial operation with competitive performance compared to other adsorbents.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Investigation of the Mechanical Degradation of Zinc-Based Cold Spray Coatings for Steel Pipelines

Internal corrosion in wet natural gas is a big challenge in the oil and gas industry due to corrosive constituents such as carbon dioxide (CO2), hydrogen sulfide (H2S), other forms of sulfur, and water in the gas stream. To mitigate internal corrosion, zinc-based cold spray coatings were designed for use in natural gas pipelines to increase the lifespan of the pipeline network. However, one of the requirements in designing internal coatings is the resistance of the coatings to mechanical forces applied on the pipeline's internal wall during pigging operations. These forces are primarily compressive and shear/friction forces. This study examines material properties that must be considered when evaluating mechanical considerations. To determine the viability of the developed coatings with respect to the shear/friction forces, the shear adhesion and wear resistance of the materials have been evaluated. Shear adhesion testing was performed with modified clevises to determine the shear stress required to cause adhesion failure at the coating/substrate interface. Scanning electron microscopy was utilized to characterize the interfaces after failure. Wear testing was performed on coatings and pipeline materials utilizing pin-on-drum testing. These tests display the stress limitations and wear that the coatings can tolerate from pigging.

mechanical degradation↗
DOE OSTI2023

Imaging Light‐Induced Migration of Dislocations in Halide Perovskites with 3D Nanoscale Strain Mapping

Abstract In recent years, halide perovskite materials have been used to make high‐performance solar cells and light‐emitting devices. However, material defects still limit device performance and stability. Here, synchrotron‐based Bragg coherent diffraction imaging is used to visualize nanoscale strain fields, such as those local to defects, in halide perovskite microcrystals. Significant strain heterogeneity within MAPbBr 3 (MA = CH 3 NH 3 + ) crystals is found in spite of their high optoelectronic quality, and both 〈100〉 and 〈110〉 edge dislocations are identified through analysis of their local strain fields. By imaging these defects and strain fields in situ under continuous illumination, dramatic light‐induced dislocation migration across hundreds of nanometers is uncovered. Further, by selectively studying crystals that are damaged by the X‐ray beam, large dislocation densities and increased nanoscale strains are correlated with material degradation and substantially altered optoelectronic properties assessed using photoluminescence microscopy measurements. These results demonstrate the dynamic nature of extended defects and strain in halide perovskites, which will have important consequences for device performance and operational stability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Extrusion‐Spheronization of Mock Energetic Materials

The primary method for producing plastic bonded explosive (PBX) granules, or “prills”, has remained relatively unchanged for 70 years despite the complex nature of the process. In this work, we demonstrate the feasibility of using an extrusion‐spheronization technique to produce prills for PBX applications. We begin by detailing an inert formulation with similar properties of PBXs and then demonstrate the extrusion‐spheronization processing of these materials. A study is then performed where the spheronization process time of the extruded materials is varied and the resultant prills are morphologically characterized. Further, these prills are then pressed into high‐density articles and subject to compression testing to elucidate trends in process, properties, and performance. It was found that, for our formulation (95 wt.% melamine/5 wt.% polymer binder) and process, a spheronization time of 60 s yielded relatively uniform particles that exhibited improved poured, tapped, and pressed densities. Mechanical strength did not have a strong trend with process time as all spheronized materials had similar peak compression stress at failure. After further optimization, extrusion‐spheronization may be a promising path for future PBX formulation.

extrusion spheronization↗
DOE OSTI2022

A Subspace-Inclusive Sampling Method for the Computational Design of Compositionally Graded Alloys

Abstract Compositionally graded alloys, a subclass of functionally graded materials (FGMs), utilize localized variations in composition with a single metal part to achieve higher performance than traditional single material parts. In previous work [Kirk, T., Galvan, E., Malak, R., and Arroyave, R., 2018, “Computational Design of Gradient Paths in Additively Manufactured Functionally Graded Materials,” J. Mech. Des., 140, p. 111410. 10.1115/1.4040816], the authors presented a computational design methodology that avoids common issues which limit a gradient alloy’s feasibility, such as deleterious phases, and optimizes for performance objectives. However, the previous methodology only samples the interior of a composition space, meaning designed gradients must include all elements in the space throughout the gradient. Because even small amounts of additional alloying elements can introduce new deleterious phases, this characteristic often neglects potentially simpler solutions to otherwise unsolvable problems and, consequently, discourages the addition of new elements to the state space. The present work improves upon the previous methodology by introducing a sampling method that includes subspaces with fewer elements in the design search. The new method samples within an artificially expanded form of the state space and projects samples outside the true region to the nearest true subspace. This method is evaluated first by observing the sample distribution in each subspace of a 3D, 4D, and 5D state space. Next, a parametric study in a synthetic 3D problem compares the performance of the new sampling scheme to the previous methodology. Lastly, the updated methodology is applied to design a gradient from stainless steel to equiatomic NiTi that has practical uses such as embedded shape memory actuation and for which the previous methodology fails to find a feasible path.

Engineering↗
DOE OSTI2024

Progress and Application of Halide Perovskite Materials for Solar Cells and Light Emitting Devices

Halide perovskite materials have attracted worldwide attention in the photovoltaic area due to the rapid improvement in efficiency, from less than 4% in 2009 to 26.1% in 2023 with only a nanometer lever photo-active layer. Meanwhile, this nova star found applications in many other areas, such as light emitting, sensor, etc. This review started with the fundamentals of physics and chemistry behind the excellent performance of halide perovskite materials for photovoltaic/light emitting and the methods for preparing them. Then, it described the basic principles for solar cells and light emitting devices. It summarized the strategies including nanotechnology to improve the performance and the application of halide perovskite materials in these two areas: from structure–property relation to how each component in the devices affects the overall performance. Moreover, this review listed the challenges for the future applications of halide perovskite materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

NNSA Advanced Photon Source Sector Opportunities Workshop (Workshop Summary)

An NNSA-Argonne National Laboratory workshop to define NNSA and external partner mission needs and opportunities at the Advanced Photon Source was held February 15-17, 2022. This workshop summary provides a fresh look at NNSA’s evolving mission needs, partner agency and university interests, x-ray photon characteristics, and technical requirements to meet those needs. The workshop was organized according to four breakout groups: Coupling dynamic drivers to a synchrotron, High explosives and chemical sciences, Process-structure-performance: X-ray experiments to understand materials behaviors, and Process-structure-performance: manufacturing and aging. This summary report describes the workshop outcomes, and the preliminary conceptual design for a dedicated Defense Materials Science Sector (DMSS) at the Advanced Photon Source.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Progress and Challenges in Self-Healing Cementitious Materials

Concrete is the most used man-made material today consisting of a mixture of aggregates (sand, gravel, crashed rock) and paste. The paste component, made up of cement and water, cracks with time. Despite this shortcoming, research towards next-generation cement and concrete has only taken a boost in the past 10-15 years. In particular, self-healing cementitious materials is a research area that has attracted a great deal of attention. A number of reported novel formulations have demonstrated an increase in mechanical and chemical stability with respect to conventional Portland cement, through the addition of inorganic, organic, and even biological additives. This review reports on the latest advances in cement research related to the synthesis of self-healing cements applied in concrete structures. These include geopolymers, engineered cementitious materials (ECC), bacterial cement composites, microencapsulated self-healing materials, shape memory alloys (SMA), and polymer-cement composites. This work describes the performance of each cementitious material and the mechanism responsible for self-healing, including a section on the latest computational modeling studies towards this end. A detailed understanding of these various self-healing cement technologies, including their strengths and weaknesses, is critical at the time of determining the type of structures that these materials could be used for.

Fernandez, Carlos A.↗
DOE OSTI2021

Tribological behavior of ceramic-alloy bearing contacts in molten salt lubrication for concentrating solar power

Molten salts are considered as candidate heat transfer fluids and thermal energy storage media for next generation concentrating solar power (CSP). A molten salt circulates inside the piping and heat exchanger and also functions as a lubricant for the sleeve bearings of the CSP pump. Furthermore, wear- and corrosion-resistant high-temperature bearing materials are critical for the pump efficiency and durability. This study evaluated the tribological performance of candidate bearing materials in lubrication of a molten chloride salt mixture (20% NaCl + 40% MgCl 2 + 40% KCl) at 750 °C in an inert argon gas (a simulative CSP pump environment). Six ceramic-alloy pairs were tested, zirconia and silicon nitride against Haynes 244, Hastelloy C276, and Tribaloy T900 alloy, and ranked by the friction coefficient and wear loss. Characterization of worn surfaces suggested the wear mechanism as a combination of abrasion, adhesion, and tribocorrosion. Results from this study provide fundamental insight for the development and selection of bearing materials for molten salt powered CSP pumps.

14 SOLAR ENERGY↗