Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high current densities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Fusion Pilot Plant performance and the role of a Sustained High Power Density tokamak

Recent U.S. fusion development strategy reports all recommend that the U.S. should pursue innovative science and technology to enable construction of a Fusion Pilot Plant (FPP) that produces net electricity from fusion at low capital cost. Compact tokamaks have been proposed as a means of potentially reducing the capital cost of a fusion pilot plant. However, compact steady-state tokamak FPPs face the challenge of integrating a high fraction of self-driven current with high core confinement, plasma pressure, and high divertor parallel heat flux. This integration is sufficiently challenging that a dedicated sustained-high-power-density (SHPD) tokamak facility is proposed by the U.S. community as the optimal way to close this integration gap. Performance projections for the steady-state tokamak FPP regime are presented and a preliminary SHPD device with substantial flexibility in lower aspect ratio (A=2-2.5), shaping, and divertor configuration to narrow gaps to a FPP is described.

core-edge integration↗
DOE OSTI2022

Overview of the LANL Double Shell Campaign [Slides]

A volume burning ignition target allows for high temperature with comparitvely lower areal density. The large number of interfaces allows for a deep investigation of the impact of hydrodynamic instabilities on implosion quality. Machine learning is currently being leveraged to improve the quality of the design. Due to the presence of high-z material we must take a deeper level of hohlraum physics into account compared to single shell designs.

36 MATERIALS SCIENCE↗
NASA NTRS2007

High Specific Power Motors in LN2 and LH2

A switched reluctance motor has been operated in liquid nitrogen (LN2) with a power density as high as that reported for any motor or generator. The high performance stems from the low resistivity of Cu at LN2 temperature and from the geometry of the windings, the combination of which permits steady-state rms current density up to 7000 A/cm2, about 10 times that possible in coils cooled by natural convection at room temperature. The Joule heating in the coils is conducted to the end turns for rejection to the LN2 bath. Minimal heat rejection occurs in the motor slots, preserving that region for conductor. In the end turns, the conductor layers are spaced to form a heat-exchanger-like structure that permits nucleate boiling over a large surface area. Although tests were performed in LN2 for convenience, this motor was designed as a prototype for use with liquid hydrogen (LH2) as the coolant. End-cooled coils would perform even better in LH2 because of further increases in copper electrical and thermal conductivities. Thermal analyses comparing LN2 and LH2 cooling are presented verifying that end-cooled coils in LH2 could be either much longer or could operate at higher current density without thermal runaway than in LN2.

Brown, Gerald V.↗
NASA NTRS2007

High Specific Power Motors in LN2 and LH2

A switched reluctance motor has been operated in liquid nitrogen (LN2) with a power density as high as that reported for any motor or generator. The high performance stems from the low resistivity of Cu at LN2 temperature and from the geometry of the windings, the combination of which permits steady-state rms current density up to 7000 A/sq cm, about 10 times that possible in coils cooled by natural convection at room temperature. The Joule heating in the coils is conducted to the end turns for rejection to the LN2 bath. Minimal heat rejection occurs in the motor slots, preserving that region for conductor. In the end turns, the conductor layers are spaced to form a heat-exchanger-like structure that permits nucleate boiling over a large surface area. Although tests were performed in LN2 for convenience, this motor was designed as a prototype for use with liquid hydrogen (LH2) as the coolant. End-cooled coils would perform even better in LH2 because of further increases in copper electrical and thermal conductivities. Thermal analyses comparing LN2 and LH2 cooling are presented verifying that end-cooled coils in LH2 could be either much longer or could operate at higher current density without thermal runaway than in LN2.

Brown, Gerald V.↗
NASA NTRS2006

Current Sheet Evolution In The Aftermath Of A CME Event

We report on SOHO UVCS observations of the coronal restructuring following a coronal mass ejection (CME) on 2002 November 26, at the time of a SOHO-Ulysses quadrature campaign. Starting about 1.5 hr after a CME in the northwest quadrant, UVCS began taking spectra at 1.7 R, covering emission from both cool and hot plasma. Observations continued, with occasional gaps, for more than 2 days. Emission in the 974.8 A line of [Fe XVIII], indicating temperatures above 6 x 10(exp 6) K, was observed throughout the campaign in a spatially limited location. Comparison with EIT images shows the [Fe XVIII] emission to overlie a growing post-flare loop system formed in the aftermath of the CME. The emission most likely originates in a current sheet overlying the arcade. Analysis of the [Fe XVIII] emission allows us to infer the evolution of physical parameters in the current sheet over the entire span of our observations: in particular, we give the temperature versus time in the current sheet and estimate its density. At the time of the quadrature, Ulysses was directly above the location of the CME and intercepted the ejecta. High ionization state Fe was detected by the Ulysses SWICS throughout the magnetic cloud associated with the CME, although its rapid temporal variation suggests bursty, rather than smooth, reconnection in the coronal current sheet. The SOHO-Ulysses data set provided us with the unique opportunity of analyzing a current sheet structure from its lowest coronal levels out to its in situ properties. Both the remote and in situ observations are compared with predictions of theoretical CME models.

Bemporad, A.↗
DOE OSTI2020

Kinetically Stable Oxide Overlayers on Mo 3 P Nanoparticles Enabling Lithium–Air Batteries with Low Overpotentials and Long Cycle Life

The main drawbacks of today's state-of-the-art lithium–air (Li–air) batteries are their low energy efficiency and limited cycle life due to the lack of earth-abundant cathode catalysts that can drive both oxygen reduction and evolution reactions (ORR and OER) at high rates at thermodynamic potentials. Here, inexpensive trimolybdenum phosphide (Mo 3 P) nanoparticles with an exceptional activity—ORR and OER current densities of 7.21 and 6.85 mA cm –2 at 2.0 and 4.2 V versus Li/Li + , respectively—in an oxygen-saturated non-aqueous electrolyte are reported. The Tafel plots indicate remarkably low charge transfer resistance—Tafel slopes of 35 and 38 mV dec –1 for ORR and OER, respectively—resulting in the lowest ORR overpotential of 4.0 mV and OER overpotential of 5.1 mV reported to date. Using this catalyst, a Li–air battery cell with low discharge and charge overpotentials of 80 and 270 mV, respectively, and high energy efficiency of 90.2% in the first cycle is demonstrated. Furthermore, a long cycle life of 1200 is also achieved for this cell. Density functional theory calculations of ORR and OER on Mo 3 P (110) reveal that an oxide overlayer formed on the surface gives rise to the observed high ORR and OER electrocatalytic activity and small discharge/charge overpotentials.

25 ENERGY STORAGE↗
NASA NTRS1995

Variation of fractional electron density fluctuations inside 40 R(sub 0) observed by Ulysses ranging measurements

The first measurements of fractional electron density fluctuations delta-n(sub e)/n(sub e), where delta-n(sub e) is rms electron density fluctuation and n(sub e) is the mean electron density, have been carried out inside 40 R(sub 0) using 1991 Ulysses dual-frequency S- and X-band (13 and 3.6 cm) ranging (time delay) measurements. In the frequency band of approximately 6 x 10(exp -5) - 8 x 10(exp -4) Hz (periods of 20 min to 5 hr), delta-n(sub e)/n(sub e) varies from a high near 20% in the slow wind close to the neutral line to a low of 1% in the fast wind far from the neutral line. For spatial wavenumber K approximately = 1.4 x 10(exp -6)/km (period of 5 hr at 250 km/s), delta-n(sub e)/n(sub e) is essentially independent of heliocentric distance over 0.03-1.0 AU in the slow wind; it is a factor of 30 lower in the fast wind than in the slow wind inside 0.1 AU, but exhibits dramatic growth with heliocentric distance inside 0.3 AU. This latter result reinforces current views of the evolution of MHD turbulence and the association of Alfven waves with high speed streams based on in situ fields and particles measurements beyond 0.3 AU. That regions of enhanced density fluctuations near or above the neutral line coincide with regions of enhanced density confirms previous conclusions that they are the interplanetary manifestation of the heliospheric current sheet and extensions of coronal streamers. While the regions of enhanced density fluctuations lie within those of enhanced density, they have boundaries that are distinctly more abrupt, suggesting the separation of plasma of different nature and origin.

Woo, Richard↗
DOE OSTI2024

High power density compact drive integrated motor for electric transportation

This project, initially part of OPEN 2018, and subsequently the ASCEND effort, targeted demonstration of significant enhancements in internal permanent magnet (IPM) motor torque and power density for current and future ground and air electric transportation applications. These were achieved through: (1) embedded two-phase system thermal management, (2) coupled, multi-scale electrical-electromagnetic-thermal-mechanical co-design and optimization, (3) size and weight reduction of motor and drive electronics through elimination of redundant cooling and coupling hardware, and (4) higher efficiency operation of SiC wide bandgap power electronics packaging through high temperature operation (200 oC). The proposed approach utilizes a single dielectric coolant for closed loop two-phase thermal management, and a combined heat rejection unit for the IPM and drive. Wick assisted liquid delivery for evaporative thermal management is utilized for the motor, and the drive electronics utilize the same coolant in flow boiling within the cold plate structures. Through the use of three-dimensional packaging for SiC, and novel drive topologies with reduced switching losses, significant increases in power density and compactness were targeted.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1975

Review of NASA short-haul studies

The paper summarizes the results of NASA-conducted technological and economic studies of low, medium, and high density short-haul transportation systems. Aircraft concepts considered included CTOL, RTOL, STOL, and general aviation aircraft. For low density systems, it was found that viable air service becomes possible if city pairs are at least 100 km apart and a two-way total travel demand of at least 200 daily passengers exists. Currently available aircraft were found suitable. The medium-density study showed that a 60-passenger twin engine turbofan was the best suited aircraft. For high density systems, STOL appears to be an economically viable means of reducing noise and congestion at major hub airports. Adequate runways 914 m in length or greater either already exist or could be added to most existing major hub airports.

Kenyon, G. C.↗
NASA NTRS2018

Characterization of a 100-kW Class Nested-Channel Hall Thruster

The next generation of electric propulsion consists of systems in excess of 300 kW of power. These systems enable a wide variety of missions, including crewed missions to near-Earth asteroids and Mars. Hall thrusters are a particularly attractive technology for these missions, but development and demonstration of 100-kW class devices has been limited to date. Here, a 100-kW class three-channel nested Hall thruster called the X3 was operated up to 102 kW total discharge power. The three channels of the X3 can be operated in any combination, providing seven unique configurations and a total throttling envelope of 2-200 kW. Previous testing of the X3 was limited to 30 kW and found that it was not providing state-of-the-art performance.Two low-power test campaigns were completed at the University of Michigan which identified potential mechanisms for this under-performance. Improvements to the thruster were made before a high-power performance characterization at NASA Glenn Research Center. There, the X3 was fired on xenon propellant from 5-102 kW total power. The thruster demonstrated stable operation in all seven channel combinations at discharge voltages from 300 V to 500 V and three different current densities. All seven channel combinations demonstrated similar performance at a given discharge voltage and current density. The largest thrust recorded was 5.4 N, and total efficiency and specific impulse ranged from 0.54 to 0.67 and 1800 seconds to 2650 seconds, respectively.In addition to the performance measurements, a suite of plasma diagnostics and a high-speed camera were used to study the operation of the thruster in greater detail. The probe results are compared against those in the literature and demonstrate that the X3, even in multi-channel operation, is producing similar charge, mass, current, and voltage utilization efficiencies as state of the art single-channel Hall thrusters. High-speed camera analysis identified that the X3 operated with similar discharge current oscillations at all conditions tested. Additionally, a preliminary calculation of cross-channel ingestion and its effect on thruster efficiency is made. This work represents the highest total power (102 kW), thrust (5.4 N), and discharge current (247 A) demonstrated by a Hall thruster to date, improvements of 6 percent, 64 percent, and 119 percent respectively over previous values. These results are discussed in the context of continued high-power Hall thruster development and future mission applications.

Hall, Scott James↗
DOE OSTI2024

Theoretical Prediction and Experimental Verification of IrO x Supported on Titanium Nitride for Acidic Oxygen Evolution Reaction

Reducing iridium (Ir) catalyst loading for acidic oxygen evolution reaction (OER) is a critical strategy for large-scale hydrogen production via proton exchange membrane (PEM) water electrolysis. However, simultaneously achieving high activity, long-term stability, and reduced material cost remains challenging. To address this challenge, we develop a frame-work by combining density functional theory (DFT) prediction using model surfaces and proof-of-concept experimental ver-ification using thin films and nanoparticles. DFT results predict that oxidized Ir monolayers over titanium nitride (IrO x /TiN) should display higher OER activity than IrO x while reducing Ir loading. Further, this prediction is verified by depositing Ir monolayers over TiN thin films via physical vapor deposition. The promising thin film results are then extended to commercially viable powder IrO x /TiN catalysts, which demonstrate a lower overpotential and higher mass activity than commercial IrO 2 , and a long-term stability of 250 hours to maintain a current density of 10 mA cm -2 . The superior OER performance of IrO x /TiN is further confirmed using proton exchange membrane water electrolyzer (PEMWE), which shows a lower cell voltage than commercial IrO 2 to achieve a current density of 1 A cm -2 . Both DFT and in situ X-ray absorption spectroscopy reveal that the high OER performance of IrO x /TiN strongly depends on the IrO x - TiN interaction via direct Ir-Ti bonding. This study highlights the importance of close interaction between theoretical prediction based on mechanistic understanding and experimental verification based on thin film model catalysts to facilitate the development of more practical powder IrO x /TiN catalysts with high activity and stability for acidic OER.

08 HYDROGEN↗
DOE OSTI2024

Fluorine-Tuned Carbon-Based Nickel Single-Atom Catalysts for Scalable and Highly Efficient CO 2 Electrocatalytic Reduction

Electrocatalytic CO 2 reduction is garnering significant interest due to its potential applications in mitigating CO 2 and producing fuel. However, the scaling up of related catalysis is still hindered by several challenges, including the cost of the catalytic materials, low selectivity, small current densities to maintain desirable selectivity. In this study, Fluorine (F) atoms were introduced into an N-doped carbon-supported single nickel (Ni) atom catalyst via facile polymer-assisted pyrolysis. This method not only maintains the high atom utilization efficiency of Ni in a cost-effective and sustainable manner but also effectively manipulates the electronic structure of the active Ni-N 4 site through F doping. The catalyst has also been further optimized by controlling the F states, including convalent and semi-ionic states, by adjusting the fluorine sources involved. Consequently, this catalyst with unique structure exhibited comparable electrocatalytic performance for CO 2 -to-CO conversion, achieving a Faradaic efficiency (FE) of over 99% across a wide potential range and an exceptional CO evolution rate of 9.5 x 10 4 h -1 at -1.16 V vs reversible hydrogen electrode (RHE). It also delivered a practical current of 400 mA cm -2 while maintaining more than 95% CO FE. Experimental analysis combined with density functional theory (DFT) calculations have also shown that F-doping modifies the electron configuration at the central Ni-N 4 sites. In conclusion, this modification lowers the energy barrier for CO 2 activation, thereby facilitating the production of the crucial *COOH intermediate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Robust Avalanche (1.5 kV, 2 kA/cm²) in Vertical GaN Diodes on Patterned Sapphire Substrate

The lack of avalanche capability is a key limitation of current lateral GaN devices. Despite the report of avalanche in vertical GaN-on-GaN devices, the high wafer cost hinders device commercialization. Here, in this work, we demonstrate a circuit-level avalanche in vertical GaN diodes on low-cost patterned sapphire substrate (PSS), with the avalanche voltage (1.57 kV) and avalanche current density (>2 kA/cm 2 ) both being the highest reported in GaN devices on foreign substrates. The PSS enables a lower dislocation density than conventional sapphire substrate and is employed in high-voltage GaN devices for the first time. The avalanche voltage in the circuit test reaches 98% of the parallel-plane limit, further affirming that near-ideal avalanche breakdown can be realized on GaN devices on foreign substrates. These results show the promise of the GaN-on-PSS platform for low-cost, robust power devices.

42 ENGINEERING↗
DOE OSTI2021

Scalable fabrication of high activity nanoporous copper powders for electrochemical CO 2 reduction via ball milling and dealloying

Electrochemical CO 2 reduction (ECR) is a promising technology to close the anthropic CO 2 circle using renewable energy to achieve carbon neutrality. Future commercialization of ECR will require the development of new catalyst synthesis routes that will allow significant upscaling of catalyst production from current research-level milligram quantities to the kilogram scale and beyond while maintaining the activity and selectivity demonstrated at the research level. Here, we report on generating and testing submicron-sized nanoporous copper (npCu) particles by using a scalable approach consisting of ball milling brittle Cu-based intermetallics followed by dealloying to add nanoporosity for high surface area. The resulting npCu particles have been tested in an industry-relevant large area (25 cm 2 ) electrolyzer platform and showed Faraday efficiencies (FE) for ethylene up to 34 % at current densities of 75–100 mA/cm 2 while keeping FE for hydrogen less than 30 %. Our results demonstrate that a combination of ball milling and dealloying is a promising approach to generate large quantities of high activity and high surface area npCu particles for ECR at an industry-relevant scale.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS2003

Ground Tests of High-Voltage Solar Arrays Immersed in a Low Density Plasma

Five different types of solar arrays have been tested in large vacuum chamber. Arc inception voltages, arc rates, and current collections are measured for samples with different coverglass materials and thickness, interconnect designs, and cell sizes. It is shown that the array with wrapthrough interconnects have the highest arc threshold and the lowest current collection. Coverglass design with overhang results in decrease of current collection and increase of arc threshold. Doubling coverglass thickness does not improve measured array parameters. Both arc inception voltage and current collection increase significantly with increasing a sample temperature to 80 C. Sustained discharges are initiated between adjacent cells with potential differences of 40 V for the sample with 300 pm coverglass thickness and 60 V for the sample with 150 urn coverglass thickness.

Vayner, Boris↗
DOE OSTI2022

Current‐Dependent Lithium Metal Growth Modes in “Anode‐Free” Solid‐State Batteries at the Cu|LLZO Interface

Abstract Controlling the lithium growth morphology in lithium reservoir‐free cells (RFCs), so‐called “anode‐free” solid‐state batteries, is of key interest to ensure stable battery operation. Despite several benefits of RFCs like improved energy density and easier fabrication, issues during the charging of the cell hinder the transition from lithium metal batteries with a lithium reservoir layer to RFCs. In RFCs, the lithium metal anode is plated during the first charging step at the interface between a metal current collector and the solid electrolyte, which is prone to highly heterogeneous growth instead of the desired homogeneous film‐like growth. Herein, the lithium morphology during the first charging step in RFCs is explored as a function of current density and current collector thickness. Using operando scanning electron microscopy, an increase in the lithium particle density is observed with increasing current density at the Cu|Li 6.25 Al 0.25 La 3 Zr 2 O 12 interface. This observation is then applied to improve the area coverage of lithium by pulsed plating. It is also shown that thin current collectors ( d = 100 nm) are unsuited for RFCs, as lithium whiskers penetrate them, resulting in highly heterogeneous interfaces. This suggests the use of thicker metal layers (several µm) to mitigate whisker penetration and facilitate homogeneous lithium plating.

25 ENERGY STORAGE↗
DOE OSTI2026

Carbon nanodot precursors enable ultrahigh-loading copper single-atom catalysts for oxygen reduction reaction

Single-atom catalysts (SACs) have attracted significant attention in electrocatalysis due to their high metal utilization and tunable electronic structures; however, their practical implementation is often limited by poor atomic dispersion, low metal loadings (typically < 1 wt%), and insufficient anchoring of single metal atoms on catalyst supports. Herein, we report a simple and versatile strategy to synthesize copper single-atom catalysts (Cu-SACs) with ultrahigh metal loading using citric-acid-derived carbon nanodots as metal-capturing precursors. Through hydrothermal treatment followed by pyrolysis in the presence of urea, atomically dispersed copper atoms coordinated with nitrogen are incorporated into a carbon framework, achieving a Cu loading of up to 20 wt% while maintaining atomic dispersion. Notably, a significant fraction of the copper single atoms exists as Cu+–N2 coordination, which provides under-coordinated and catalytically active sites. The resulting Cu-SAC exhibits promising oxygen reduction reaction (ORR) activity in alkaline media, delivering a limiting current density comparable to that of commercial 20 wt% Pt/C with a predominant four-electron reduction pathway. Despite this high intrinsic activity, durability tests reveal gradual performance degradation under prolonged electrochemical operation, which is attributed to demetallation and aggregation of copper single atoms into metallic nanoparticles. These results demonstrate the potential of carbon nanodot-based platforms for synthesizing high-loading SACs, while underscoring the critical need to simultaneously control carbon porosity and metal–nitrogen coordination to enhance active-site accessibility and durability.

Sharma, Prakhar [University of Kentucky]↗
NASA NTRS1993

Process for producing a high emittance coating and resulting article

Process for anodizing aluminum or its alloys to obtain a surface particularly having high infrared emittance by anodizing an aluminum or aluminum alloy substrate surface in an aqueous sulfuric acid solution at elevated temperature and by a step-wise current density procedure, followed by sealing the resulting anodized surface. In a preferred embodiment the aluminum or aluminum alloy substrate is first alkaline cleaned and then chemically brightened in an acid bath The resulting cleaned substrate is anodized in a 15% by weight sulfuric acid bath maintained at a temperature of 30.degree. C. Anodizing is carried out by a step-wise current density procedure at 19 amperes per square ft. (ASF) for 20 minutes, 15 ASF for 20 minutes and 10 ASF for 20 minutes. After anodizing the sample is sealed by immersion in water at 200.degree. F. and then air dried. The resulting coating has a high infrared emissivity of about 0.92 and a solar absorptivity of about 0.2, for a 5657 aluminum alloy, and a relatively thick anodic coating of about 1 mil.

Le, Huong G.↗