Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “emulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Investigation of magnetic noise from conductive shields in the 10–300 kHz frequency range

Here we present experimental and theoretical investigations of magnetic noise originating from radio-frequency (RF) conductive shields of flat geometry in the inductance-dominated impedance regime below 300 kHz. The measurement is based on a Q-factor determination of a coil that provides a sufficient sensitivity, placed at the position where the shield magnetic noise is measured. The theory is based on calculations of magnetic field and inductance of one or a few flat rings that emulate a conductive shield. The theoretical model is found to be in close agreement with experimental data. It can be used to predict the magnetic noise of a conductive shield with different thicknesses, conductivities, and temperatures at different distances for a wide range of frequencies. Although the model can be generalized for a more arbitrary shield geometry, in its presented form, it can be applied to the magnetic noise predictions when the shield surface curvature is not large. One important conclusion is that the RF conductive shield can generate the magnetic noise much lower than femtotesla, and, thus, it can be used in many precision experiments targeting minute high-frequency magnetic signals, such as detection of magnetic resonance imaging and nuclear quadrupole resonance signals and search for axion dark matter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Quantum simulations employing connected moments expansions

Further advancement of quantum computing (QC) is contingent on enabling many-body models that avoid deep circuits and excessive use of CNOT gates. To this end, we develop a QC approach employing finite-order connected moment expansions (CMX) and affordable procedures for initial state preparation. We demonstrate the performance of our approach employing several quantum variants of CMX through the classical emulations on the H2 molecule potential energy surface and the Anderson model with a broad range of correlation strength. The results show that our approach is robust and flexible. Good agreements with exact solutions can be maintained even at the dissociation and strong correlation limits.

quantum computing, quantum chemistry, Electron cor↗

Energy-angle distribution of the ions in the RF sheath of ICRH antennas

Radio-frequency sheaths forming at the surface of ion cyclotron resonance heating (ICRH) actuators in fusion experiments are associated with enhanced impurity sputtering from ICRH plasma-facing components (PFCs). The minimization of impurity fluxes from the ICRH PFC is a vital task for the usage of ICRH systems. Capturing the ion kinetics is important for an accurate description of plasma–material interactions, because the ion dynamics plays a crucial role in RF sheaths. Here, we present a hybrid particle-in-cell (hPIC) model able to capture the kinetic behavior of the ions. We analyze the kinetic ion energy-angle distributions (IEADs) impacting the RF antenna and its dependence on different plasma and RF sheath parameters. In particular, the IEAD dependence on RF frequency and magnetic field alignment is investigated. Using hPIC, we simulated a case emulating the latest experimental campaign from JET. The simulation showed that under specific plasma and RF parameters, the kinetic motion of ions results in a cusp formation in the IEAD.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The design of a photoionization front experiment using the Z-Machine as a driving source and estimated measurements

Radiation-driven heat fronts are present in the early universe during reionization, the circumstellar medium of supernovae, and in high-energy-density physics experiments. Dedicated experiments to observe and diagnose the behavior of these types of heat fronts can improve our understanding of these phenomena. A simulation study of photoionization fronts using the HELIOS-CR radiation hydrodynamics code provides an experimental design for the Z-Machine at Sandia National Laboratory using a measurement-calibrated input radiation flux to drive the photoionization front. The simulations use detailed atomic physics and non-diffusive radiation transport in 1D to determine an optimal gas pressure of 0.75 atm for an experiment in N gas as well as the effects of increasing the thickness of the window that seals the gas cell. Post-processing of these simulations demonstrates that ratios of atomic rate coefficients place the heat front in a physics regime where photoionization dominates the energy deposition. Here, to see the sensitivity of the simulations to changes in the model and spatial grid, this analysis performed resolution, atomic model detail, and radiation transport angular grid studies showing less than 10% deviation from the nominal model for increased complexity, when possible. An effort to emulate 3D geometric effects on the radiation flux using an artificial attenuation scheme has shown that, even for conservative estimates of the flux, simulations still produce a photoionization front. Estimations of a streaked, visible spectroscopy measurement using SPECT3D showed that line emission measurements are present early in time and that later in time thermal emission should become dominant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Intrinsic synaptic plasticity of ferroelectric field effect transistors for online learning

Nanoelectronic devices emulating neuro-synaptic functionalities through their intrinsic physics at low operating energies is imperative toward the realization of brain-like neuromorphic computers. In this work, we leverage the non-linear voltage dependent partial polarization switching of a ferroelectric field effect transistor to mimic plasticity characteristics of biological synapses. Here, we provide experimental measurements of the synaptic characteristics for a 28nm high-k metal gate technology based device and develop an experimentally calibrated device model for large-scale system performance prediction. Decoupled read-write paths, ultra-low programming energies and the possibility of arranging such devices in a cross-point architecture demonstrate the synaptic efficacy of the device. Our hardware-algorithm co-design analysis reveals that the intrinsic plasticity of the ferroelectric devices has potential to enable unsupervised local learning in edge devices with limited training data

42 ENGINEERING↗

Detecting hidden transient events in noisy nonlinear time-series

The information impulse function (IIF), running Variance, and local Hölder Exponent are three conceptually different time-series evaluation techniques. These techniques examine time-series for local changes in information content, statistical variation, and point-wise smoothness, respectively. Using simulated data emulating a randomly excited nonlinear dynamical system, this study interrogates the utility of each method to correctly differentiate a transient event from the background while simultaneously locating it in time. Computational experiments are designed and conducted to evaluate the efficacy of each technique by varying pulse size, time location, and noise level in time-series. Our findings reveal that, in most cases, the first instance of a transient event is more easily observed with the information-based approach of IIF than with the Variance and local Hölder Exponent methods. While our study highlights the unique strengths of each technique, the results suggest that very robust and reliable event detection for nonlinear systems producing noisy time-series data can be obtained by incorporating the IIF into the analysis.

42 ENGINEERING↗

Hybrid stochastic synapses enabled by scaled ferroelectric field-effect transistors

Achieving brain-like density and performance in neuromorphic computers necessitates scaling down the size of nanodevices emulating neuro-synaptic functionalities. However, scaling nanodevices results in reduction of programming resolution and emergence of stochastic non-idealities. While prior work has mainly focused on binary transitions, in this work, we leverage the stochastic switching of a three-state ferroelectric field-effect transistor to implement a long-term and short-term two-tier stochastic synaptic memory with a single device. Experimental measurements are performed on a scaled 28 nm high-k metal gate technology-based device to develop a probabilistic model of the hybrid stochastic synapse. In addition to the advantage of ultra-low programming energies afforded by scaling, our hardware–algorithm co-design analysis reveals the efficacy of the two-tier memory in comparison to binary stochastic synapses in on-chip learning tasks—paving the way for algorithms exploiting multi-state devices with probabilistic transitions beyond deterministic ones.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A gas dynamic perspective on particle lifting in electrostatic discharge-like devices using multiphase particle-in-cell approach

Although particle–laden electrostatic discharges are widely used in laboratories as well as in industrial applications, the mechanism of particle lifting for particles initially at rest in such highly unsteady systems is not well understood. A multiphase gas–particle solver is developed using the multiphase particle-in-cell (MP-PIC) approach to emulate the interaction of a compressible shock-dominated gas phase with the dense particle phase. First, the two-way coupled solver is initially used to study the interaction of a planar traveling shock with a vertical curtain of particulates. The gas and particle phase evolution was found to be in good agreement with a similar experimental study in Ling et al. [Phys. Fluids 24, 113301 (2012)]. Second, the MP-PIC code is used to study the interaction of an expanding blast wave with a thick bed of particles. The simulation considered forces such as quasi-steady drag, pressure-gradient, added-mass, Saffman, and Magnus forces. We observe that the vertical liftoff particles close to the shock impingement point in this configuration are associated with the quasi-steady drag, pressure gradient, and added-mass forces. Also, the Saffman lift and Magnus forces contribute to lifting particles located radially farther away from the shock impingement point. In addition, the study finds a decrease in particle lifting efficiency with decreasing plasma kernel length and shock strength.

42 ENGINEERING↗

A comparison of QTP functionals against coupled-cluster methods for EAs of small organic molecules

EA-EOM-CCSD electron affinities and LUMO energies of various Kohn–Sham density functional theory (DFT) methods are calculated for an a priori IP benchmark set of 64 small, closed-shell molecules. The purpose of these calculations was to investigate whether the QTP KS-DFT functionals can emulate EA-EOM-CC with only a mean-field approximation. We show that the accuracy of DFT—relative to CCSD—improves significantly when elements of correlated orbital theory are introduced into the parameterization to define the QTP family of functionals. In particular, QTP(02), which has only a single range separation parameter, provides results accurate to a MAD of <0.15 eV for the whole set of 64 molecules compared to EA-EOM-CCSD, far exceeding the results from the non-QTP family of density functionals.

Chemistry↗

Deep learning-based predictive models for laser direct drive at the Omega Laser Facility

The rich and complex physics of inertial confinement fusion provides a unique and challenging space for high-fidelity first-principles modeling. Consequently, simulation codes that are used to design experiments are computationally expensive and lack the predictive capability required for extensive parameter exploration in search of a high-performing design for laser direct drive. In this article, we present two deep-learning-based predictive models intended to address these difficulties. The first model (TL DNN) acts as a fast emulator of simulations as well as experiments at the Omega Laser Facility. This model is trained on a simulation database and subsequently calibrated on experimental data using transfer learning. To facilitate the development of this model, an autoencoder is developed to reduce the dimensionality of the input space by compressing the laser pulse input. The model predicts key experimental scalar observables of Omega experiments with high accuracy and minimal computational cost. This deep neural net enables rapid exploration of a high-dimensional input parameter space for an optimal implosion design. The second model (DNN SM+) aims to extend the statistical modeling work of Lees et al. [Phys. Rev. Lett. 127, 105001 (2021)], by increasing the complexity of the model space and allowing for coupling between degradation terms. Since the model capacity of DNN SM+ is higher than the model of Lees et al., DNN SM+ can potentially provide an improvement in predictive capability, and we use this model to provide insight into complicated degradation dependencies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaluating the impact of air terminal geometry on lightning intercept efficacy under a strong background electric field

A comparative analysis of the attachment efficacy of sharpened vs blunted air terminals under a strong background DC electric field, similar to conditions found in naturally occurring lightning events, is presented. Testing was conducted using an oil-free, 17-stage, 1.4 MV bipolar Marx generator with a biased discharge plane that emulated the conditions found prior to the lightning return stroke. The biased discharge plane allowed the introduction of a strong DC electric field and subsequent corona formation on a time scale much longer than the brief duration over which the downward leader propagates. Initial observations indicate that despite a higher background electric field at the sharpened terminals, leading to pre-discharge corona formation where none is seen on the blunt terminal, both the sharpened and blunted terminals exhibit similar attachment probabilities during discharge events, with some discharge events attaching to both terminals.

54 ENVIRONMENTAL SCIENCES↗

Prevention of resistive wall tearing mode major disruptions with feedback

Resistive wall tearing modes (RWTMs) can cause major disruptions. A signature of RWTMs is that the rational surface is sufficiently close to the wall to interact with it. For (m,n) = (2,1) modes, a RWTM requires normalized minor radius of the rational surface ρ q2 ≥ 0.75, which can also be expressed as q 75 ≤ 2. Major disruptions can occur when the criterion is satisfied. This is confirmed in simulations and theory and in a DIII-D locked mode disruption database. The q 75 < 2 criterion is valid at high β as well as at low β. A very important feature of RWTMs is that they can be feedback stabilized. If the ρ q2 criterion is not satisfied, or if the wall is ideally conducting, then the mode does not produce a major disruption, although it can produce a minor disruption. Feedback, or rotation of the mode at the wall by complex feedback, can emulate an ideal wall, preventing major disruptions. The ρ q2 criterion depends weakly on the wall radius. A simple geometric model of its dependence on wall radius is given.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Irradiation-induced gas production in REBCO-based magnet materials used for future compact fusion reactors

Nuclear fusion is an enticing alternative to current sources of energy, with multilayered Rare-Earth Barium Copper Oxide (REBCO) coated conductors deemed pivotal in the race toward fully realized, commercially viable, and magnetic confinement fusion reactors. In this study, we simulated the ion spectrum expected to evolve from REBCO's nickel-based Hastelloy C-276 substrate and copper stabilizer in an affordable robust compact-like reactor. We then emulated this gas production through helium implantation to investigate changes in materials and superconducting properties. Our results revealed that the substrate and stabilizer are capable of producing protons energetic enough to recoil throughout the tape thickness in appreciable doses, and alphas energetic enough to deposit 7.54 × 1014 ions/cm2 or 50.1 helium appm in the superconducting layer over a 30-year reactor lifetime. The superconducting layer of SuperPower® tapes exhibited at least double the swelling rate of the other major layers, and both SuperPower and Fujikura Ltd. tapes displayed microstructural changes in the REBCO layer not observed in isotropic metals. For the estimated lifetime fluence, the Fujikura tapes showed a ∼1 K reduction in critical temperature and a 32% degradation in critical current for compact reactor-relevant conditions (16 T, 20 K). Nuclear transmutation, low-temperature solder implantations, gas-ion evolution, the influence of gas production on vortex dynamics, and other related considerations are also discussed.

Reis, Chris↗

Comparing ICME simulations with scaled laboratory experiment

In stellar physics and astrophysics, numerical simulations and laboratory experiments are often compared to observational data to support their representation of the real world. However, there is also merit in comparing numerical simulations to properly scaled experiments, especially when the experiment and the simulation are both emulating the solar phenomena. Confirming the credibility of scaled experiments and their scaling with well-validated models is important to expand our knowledge of the associated physical phenomena. This is significant because experiments and simulations can be performed frequently, whereas observations may be limited by location, field of view, and missing data. In this work, we use the Alfvén Wave Solar atmosphere Model, a well-validated magnetohydrodynamic model, to simulate an interplanetary coronal mass ejection (ICME) and compare it to an experiment which provides a scaled analog to a physical ICME. The experiment was performed on the Big Red Ball facility and scaled using dimensionless parameters such as plasma β and magnetosonic Mach number to reproduce the main structure of an ICME. We compare the model-simulated temperature, density, and magnetic field to those from the experiment, as well as the scaling parameters used in the experiment, to those calculated from the simulation. This comparison is performed to further justify the scaling arguments made by the experiment. Additionally, the comparison would lead to the development of stronger scaling arguments for future experiments.

Bryant, K. [University of Michigan, Ann Arbor, MI ↗

Complexity analysis of a CT injection experiment on BRB

In this work, we use Jensen–Shannon complexity and permutation entropy to analyze the magnetic field fluctuations of an astrophysically scaled plasma experiment. The experiment was intended to emulate an interplanetary coronal mass ejection event in the lab, recreating the major sections seen in satellite data. We also use a technique called “delay,” in which we use select elements, skipping one or more data points at a time, in our time series data to obtain Jensen–Shannon complexity as a function of frequency and investigate the frequency of maximized complexity. We then compare the delay frequencies to other frequencies in the plasma. We found that the frequencies for maximum complexity do not correspond to the frequencies investigated, implying that other physical mechanisms lead to an increase in complexity at these frequencies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Neural operator transformers capture bifurcating drift-wave turbulence in fusion plasma simulations

Self-consistent modeling of turbulence-driven transport is critical for optimizing confinement in magnetically confined fusion plasmas, such as tokamaks and stellarators. In particular, capturing the long-term co-evolution of turbulence, flow, and background plasma profiles remains computationally challenging. Direct numerical simulation of these multiscale, highly nonlinear processes is often demanding and impractical for real-time control or design optimization. To address this bottleneck, we investigate transformer-based neural operator partial differential equation surrogates for emulating the dynamics of drift-wave turbulence bifurcation mediated by zonal flows, using the modified Hasegawa–Wakatani (MHW) model as a prototypical system. We find that the finetuned neural operator model has excellent performance in capturing the multi-spatiotemporal-scales of MHW turbulence bifurcation and is robust to testing on rare and out-of-distribution dynamics. Specifically, we demonstrate that a single unified model accurately predicts both quasi-steady-state turbulence and a wide range of dynamical transition processes, such as nonlinear saturation, spontaneous suppression of turbulence, and the emergence of macroscopic zonal flows, over time horizons vastly exceeding the local turbulence correlation time. This computationally efficient approach establishes a strong foundation for fast, AI-based modeling of complex, multiscale phenomena in magnetized fusion plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Chemically tunable mucin chimeras assembled on living cells

Significance Mucins are a diverse and heterogeneous family of glycoproteins that have been implicated in immunity and cancer. This work establishes a rapid and scalable route to synthetic mucin constructs with precisely defined glycan densities and chain lengths. Physical characterization indicates that the constructs both chemically and structurally emulate biological mucins and that dense mucin-type O-glycosylation imparts a remarkable degree of rigidity to the peptide backbone. Dual end-functionalized mucins were covalently conjugated to an engineered membrane protein on live mammalian cells. This strategy allows systematic variation in display of cell surface mucins with numerous applications in understanding the many biological roles of this unusual glycoprotein family.

59 BASIC BIOLOGICAL SCIENCES↗

Multivalent, multiflavored droplets by design

Nature self-assembles functional materials by programming flexible linear arrangements of molecules and then folding them to make 2D and 3D objects. To understand and emulate this process, we have made emulsion droplets with specific recognition and controlled valence. Uniquely monovalent droplets form dimers: divalent lead to polymer-like chains, trivalent allow for branching, and programmed mixtures of different valences enable a variety of designed architectures and the ability to subsequently close and open structures. Our functional building blocks are a hybrid of micrometer-scale emulsion droplets and nanoscale DNA origami technologies. Functional DNA origami rafts are first added to droplets and then herded into a patch using specifically designated “shepherding” rafts. Additional patches with the same or different specificities can be formed on the same droplet, programming multiflavored, multivalence droplets. The mobile patch can bind to a patch on another droplet containing complementary functional rafts, leading to primary structure formation. Further binding of nonneighbor droplets can produce secondary structures, a third step in hierarchical self-assembly. The use of mobile patches rather than uniform DNA coverage has the advantage of valence control at the expense of slow kinetics. Droplets with controlled flavors and valences enable a host of different material and device architectures.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗