SEARCH · Engineering Papers

Results for “edge current”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Aerodynamic Effects of High Turbulence Intensity on a Variable-Speed Power-Turbine Blade with Large Incidence and Reynolds Number Variations

The effects of high inlet turbulence intensity on the aerodynamic performance of a variable speed power turbine blade are examined over large incidence and Reynolds number ranges. These results are compared to previous measurements made in a low turbulence environment. Both high and low turbulence studies were conducted in the NASA Glenn Research Center Transonic Turbine Blade Cascade Facility. The purpose of the low inlet turbulence study was to examine the transitional flow effects that are anticipated at cruise Reynolds numbers. The current study extends this to LPT-relevant turbulence levels while perhaps sacrificing transitional flow effects. Assessing the effects of turbulence at these large incidence and Reynolds number variations complements the existing database. Downstream total pressure and exit angle data were acquired for 10 incidence angles ranging from +15.8deg to −51.0deg. For each incidence angle, data were obtained at five flow conditions with the exit Reynolds number ranging from 2.12×10(exp 5) to 2.12×10(exp 6) and at a design exit Mach number of 0.72. In order to achieve the lowest Reynolds number, the exit Mach number was reduced to 0.35 due to facility constraints. The inlet turbulence intensity, Tu, was measured using a single-wire hotwire located 0.415 axial-chord upstream of the blade row. The inlet turbulence levels ranged from 8 to 15 percent for the current study. Tu measurements were also made farther upstream so that turbulence decay rates could be calculated as needed for computational inlet boundary conditions. Downstream flow field measurements were obtained using a pneumatic five-hole pitch/yaw probe located in a survey plane 7 percent axial chord aft of the blade trailing edge and covering three blade passages. Blade and endwall static pressures were acquired for each flow condition as well. The blade loading data show that the suction surface separation that was evident at many of the low Tu conditions has been eliminated. At the extreme positive and negative incidence angles, the data show substantial differences in the exit flow field. These differences are attributable to both the higher inlet Tu directly and to the thinner inlet endwall boundary layer that the turbulence grid imposes.

Flegel, Ashlie B.↗

NASA NTRS2019

First Detection of Plasmoids from Breakout Reconnection on the Sun

Transient collimated plasma ejections (jets) occur frequently throughout the solar corona, in active regions, quiet Sun, and coronal holes. Although magnetic reconnection is generally agreed to be the mechanism of energy release in jets, the factors that dictate the location and rate of reconnection remain unclear. Our previous studies demonstrated that the magnetic breakout model explains the triggering and evolution of most jets over a wide range of scales, through detailed comparisons between our numerical simulations and high-resolution observations. An alternative explanation, the resistive-kink model, invokes breakout reconnection without forming and explosively expelling a flux rope. Here we report direct observations of breakout reconnection and plasmoid formation during two jets in the fan-spine topology of an embedded bipole. For the first time, we observed the formation and evolution of multiple small plasmoids with bidirectional flows associated with fast reconnection in 3D breakout current sheets (BCSs) in the solar corona. The first narrow jet was launched by reconnection at the BCS originating at the deformed 3D null, without significant flare reconnection or a filament eruption. In contrast, the second jet and release of cool filament plasma were triggered by explosive breakout reconnection when the leading edge of the rising flux rope formed by flare reconnection beneath the filament encountered the preexisting BCS. These observations solidly support both reconnection-driven jet models: the resistive kink for the first jet, and the breakout model for the second explosive jet with a filament eruption.

Kumar, Pankaj↗

DOE OSTI2021

EXTRACTING HUMAN RELIABILITY FINDINGS FROM HUMAN FACTORS STUDIES IN THE HUMAN SYSTEMS SIMULATION LABORATORY

Modernization of U.S. nuclear power plants (NPPs) is widespread, with most plants currently replacing and transitioning equipment, control systems, and human system interfaces (HSI)s from analog to digital displays. This conversion remedies the obsolescence of analog parts along with needs for increased intuitiveness of design, safety, and capabilities. The Human Factors and Reliability team at Idaho National Laboratory (INL) carried out twelve control room modernization studies in the newly designed Human Systems Simulation Laboratory (HSSL) over nine years. The HSSL was constructed as a testbed for evaluating human factors techniques and performance measures, HSI frameworks, and cutting-edge operational concepts in NPPs. Installing a full-scope training simulator enabled direct design and evaluation work on the same instrumentation and control (I&C) and HSIs located at U.S. plants. The subsequent addition of glass top bays afforded crews opportunities to implement operations via the simulator using full-scale representations of their home NPP. Additionally, functional HSI prototypes were created, providing an environment for operator-in-the-loop benchmark studies. The HSSL has assisted in upgrades of six commercial NPP control rooms and served as an invaluable proving ground for new NPP operations technology. Human reliability analysis (HRA) was not originally the focus of the studies; however, data relating to HRA such as type and frequency of human errors can be extracted from the studies. INL is currently extracting data from the HSSL study reports to apprise how information gathered from simulation, HSI, and other related studies can create a broad look across different data sources to help inform HRA methods.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2025

Basic Physical Processes Involving Dust in Fusion Plasmas

This report presents the main outcomes of our research focused on understanding the behavior and effects of dust particles in fusion plasmas, particularly in the edge regions of tokamaks and stellarators. We conducted computer modeling studies of burst injections of carbon and tungsten dust particles in DIII-D like divertor plasmas. The studies investigated effects of transient influx of the low- and high-Z material plasma contaminants in form of dust on the edge plasma dynamics in a modern mid-size tokamak. We also performed theoretical and computational studies of the forces acting on non-spherical dust grains in magnetized and nonmagnetized plasmas. In addition, we cooperated with General Atomics slag management group on development of DIII-D dust injection experiments to measure trajectories of dust grains in the divertor plasma and compare them with DUSTT code predictions for validation of the dust modeling capabilities. We collaborated with JET experimentalists on evaluation of radiative losses induced by injection of mixed neon-deuterium ice pellets for disruption and run-away electron generation mitigation during thermal and current quench phases. We also cooperated with experimentalists at LHD fusion device (Japan) on modeling support of experiments on injection of boron granules in fusion plasma discharges to assess their dynamics and effectiveness for in situ dynamic wall conditioning.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

A numerical and experimental approach to compare the effect of sample thickness in small in-situ SEM and large ex-situ tensile testing in Alloy 709

ASTM standards for tensile tests define specific sample size requirements regardless of grain size of the material. However, sample size requirements for testing should be considered in conjunction with the number of grains within its reduced cross-sectional area. This is particularly important for in-situ Scanning Electron Microscope (SEM) tensile tests, as they have to be conducted on smaller samples. In this study, a comprehensive experimental and numerical evaluation of the effect of specimen thickness (and the resulting number of grains within the cross-section) were conducted using in-situ SEM tensile test (on submillimeter thick samples) and ex-situ tensile tests (on samples of 0.68–5.9 mm thickness) and the results are compared with FEM simulations outcome. All tests were conducted at room temperature and the results are correlated to the number of grains within the thickness of specimens. The tensile test results indicated that even though the 0.2% proof stress and the tensile strength do not vary for the current range of thicknesses (with number of grains in the cross-section varying from 13 to 118), a difference in necking mechanism exists. Post tensile strength, thinner samples undergo more shear failure and diagonal localized necking whereas thicker samples experience more diffuse necking indicated by decreased area of shear failure at the edges and increased area of dimpled tensile failure at the center of the sample. Further, FEM results complement the experimental findings by showing the formation of conjugated localized shear bands on the upper and lower surface in the 0.68 mm thick sample and shear bands combining to form singular shear bands in thicker samples. These results also confirm the validity of the in-situ SEM tensile tests conducted on thinner samples as long as the required minimum number of grains exist within the cross-section.

36 MATERIALS SCIENCE↗

DOE OSTI2020

The Role of Metal-Semiconductor Interface in Hybrid Perovskite Devices for High-Performance Radiation Photon Counting

Halide perovskites are promising optoelectronic semiconductors. For applications in solid-state detectors that operate in low photon flux counting mode, blocking interfaces are essential to minimize the dark current noise. Here, we investigate the interface between methylammonium lead tri-iodide (MAPbI 3 ) single crystals and commonly used high and low work function metals to achieve photon counting capabilities in a solid-state detector. Using scanning photocurrent microscopy, we observe a large Schottky barrier at the MAPbI 3 /Pb interface, which efficiently blocks dark current. Moreover, the shape of the photocurrent profile indicates that the MAPbI 3 single-crystal surface has a deep fermi level close to that of Au. Rationalized by first-principle calculations, we attribute this observation to the defects due to excess iodine on the surface underpinning emergence of deep band-edge states. The photocurrent decay profile yields a charge carrier diffusion length of 10–25 μm. Using this knowledge, we demonstrate a single-crystal MAPbI 3 detector that can count single γ-ray photons by producing sharp electrical pulses with a fast rise time of <2 μs. Overall, our study indicates that the interface plays a crucial role in solid-state detectors operating in photon counting mode.

36 MATERIALS SCIENCE↗

DOE OSTI2022

EJFAT: Towards Intelligent Compute Destination Load Balancing

To handle increased data flow, Jefferson Lab (JLab) is partnering with ESnet for development of an AI/ML directed compute work Load Balancer (LB) of UDP streamed data. The LB is FPGA based featuring dynamically configurable, low latency and high throughput destination address switching. The LB provides integration of edge and core computing to support JLab experimental programs, the Electron-Ion Collider, as well as data centers of the future. In the ESnet/JLab FPGA Accelerated Transport (EJFAT) initiative, the function of the LB Data Plane (DP) is to redirect data streams to selectable (but unknown to sender) destination hosts based on current worload and within that host to destination ports as a function of sub- stream id. This effects hierarchical scaling, first across compute machines for processing over a series of events and second, across ports so different data source sub-streams may be assigned to different processors for further parallelization. The LB Control Plane (CP) programs the DP using compute farm telemetry to direct and balance workloads across a compute cluster as the operating conditions require. While Proportional/Integrative/Derivative (PID) controllers are often seen in similar applications, here we investigate the feasibility of a Reinforcement Learning (RL) based schedule manager running in the CP to provide dynamic updates to the DP scheduling policy.

Lawrence, David↗

NASA NTRS1984

Potential flow analysis of glaze ice accretions on an airfoil

The results of an analytical/experimental study of the flow fields about an airfoil with leading edge glaze ice accretion shapes are presented. Tests were conducted in the Icing Research Tunnel to measure surface pressure distributions and boundary layer separation reattachment characteristics on a general aviation wing section to which was affixed wooden ice shapes which approximated typical glaze ice accretions. Comparisons were made with predicted pressure distributions using current airfoil analysis codes as well as the Bristow mixed analysis/design airfoil panel code. The Bristow code was also used to predict the separation reattachment dividing streamline by inputting the appropriate experimental surface pressure distribution.

Zaguli, R. J.↗

NASA NTRS1985

Electrodynamics of the westward traveling surge

It is shown that the global convection pattern, the ionospheric current, and the field-aligned current associated with the westward traveling surge in the asymptotic state can be modeled quantitatively as consequences of a blockage of the Hall current from closure in the magnetosphere via field-aligned currents. The conductivity is allowed to increase self-consistently with increasing upward field-aligned current in the model. This inclusion of the self-consistent enhanced ionospheric conductivity due to discrete auroral precipitations is found to generate a localized intense westward electrojet on the poleward side of the Harang discontinuity. The westward electrojet is also found to rotate counterclockwise, merging into the eastward electrojet around the leading edge of the surge. Thus the major features of the westward traveling surge can be reproduced reasonably well in the model.

Kan, J. R.↗

NASA NTRS1988

Chemical warfare protection for the cockpit of future aircraft

Currently systems are being developed which will filter chemical and biological contaminants from crew station air. In order to maximize the benefits of these systems, a method of keeping the cockpit contaminant free during pilot ingress and egress is needed. One solution is to use a rectangular plastic curtain to seal the four edges of the canopy frame to the canopy sill. The curtain is stored in a tray which is recessed into the canopy sill and unfolds in accordion fashion as the canopy is raised. A two way zipper developed by Calspan could be used as an airlock between the pilot's oversuit and the cockpit. This system eliminates the pilot's need for heavy and restrictive CB gear because he would never be exposed to the chemical warfare environment.

Pickl, William C.↗

NASA NTRS1992

Oxygen isotopes implanted in the LDEF spacecraft

Depth profiles of O-16 and O-18/O-16 were measured on stainless steel nuts and copper sheet (from a grounding strap) recovered from the leading edge of LDEF (Tray E10). The measurements were obtained by dynamic SIMS (secondary ion mass spectrometry) using a VG Isolab 54 ion microprobe. Plots of O-18/O-16 against time, show large depletions of up to a factor of 2 compared to the O-18/O-16 value at sea level. The O-16 current decreases by 2 orders of magnitude in the interior of the metal, and the corresponding profile of anomalous O-16 is strongly peaked in the outer few tens of nanometers of the surface. This depth scale is a tentative one based on estimated sputtering rates. Plots of O-18/O-16 against 1/O-16 should be linear if two isotopically distinct components, one of variable concentration (orbital component) and one of fixed concentration (normal oxygen), are mixed. Data to be presented at the meeting show departures from linearity which result from variability in the concentration of normal oxygen, but may also arise from the implantation of oxygen with a range of fractionation due to the decaying orbit of the LDEF, sputtering of the surface by atomic oxygen, and the different momenta of the two isotopes due to their equal velocities. The potential for using this method as a means of identifying exposure to low-Earth orbit, de-convoluting the effects of space exposure from terrestrial contamination, and using the implanted anomolous oxygen as a means of studying the atomic oxygen density and upper atmosphere temperature height profile will be discussed at the meeting.

Saxton, J. M.↗

NASA NTRS2003

Third Generation RLV Structural Seal Development Programs at NASA GRC

NASA is currently developing technologies for the 3rd Generation Reusable Launch Vehicle (RLV) that is being designed to enter service around the year 2025. In particular, NASA's Glenn Research Center (GRC) is working on advanced high temperature structural seal designs including propulsion system and control surface seals. Propulsion system seals are required along the edges of movable panels in advanced engines, while control surface seals seal the edges and hinge lines of movables flaps and elevons on the vehicle. The overall goal is to develop reusable, resilient seals capable of operating at temperatures up to 2000 F. High temperature seal preloading devices (e.g., springs) are also being evaluated as a means of improving seal resiliency. In order to evaluate existing and potential new seal designs, GRC has designed and is installing several new test rigs capable of simulating the types of conditions that the seals would endure during service including temperatures, pressures, and scrubbing. Two new rigs, the hot compression test rig and the hot scrub test rig, will be used to perform seal compression and scrub tests for many cycles at temperatures up to 3000 F. Another new test rig allows simultaneous flow and scrub tests to be performed on the seals at room temperature to evaluate how the flow blocking performance of the seals varies as they accumulate damage during scrubbing. This presentation will give an overview of these advanced seal development efforts.

Dunlap, Patrick H., Jr.↗

NASA NTRS2004

Characterization of the Micro Textures in a Friction Stir Weld

In friction stir welding (FSW), a rotating threaded pin tool is inserted into a weld seam and literally stirs the edges of the seam together. The Dynamically-Recrystallized-Zone (DXZ) of a polished and etched FSW cross-section exhibits contrasting bands (the "onion-ring" structure), the origins of which are unclear. An orientation image mapping (OIM) study suggests that the corresponding bands may correspond respectively to a "straight-through" current of metal bypassing the pin tool in a single rotation or less and a "maelstrom" current rotating a number of times around the pin tool.

Schneider, Judy↗

NASA NTRS2003

Fabrication And Evaluation Of Sic/Sic Tubes With Various Fiber Architectures

SiC/SiC composites are excellent material candidates for high temperature applications where the performance requirements are high strength, high creep-rupture resistance, high environmental durability, and high thermal conductivity. In the past, the NASA UEET program has demonstrated fabrication of high-performance SiC/SiC flat panels reinforced by Sylramic-iBN SiC fibers. Currently NASA UEET is scaling up this SiC/SiC system by fabrication of more complex shaped components using the same fiber type. This paper reports the effects of various fiber architectures on the processing, mechanical, and durability behavior of small-diameter 0.5" ID SiC/SiC tubes, which are potential sub-elements for leading edges and cooling channels in turbine vanes and blades. Nine different fiber architectures were utilized for construction of seamless tube preforms, from simple 2D jelly-rolling to complex braiding, pin-weaving, filament-winding and 3D orthogonal weaving with approximately 5% fibers in the thru-thickness direction. Using the BN interphase and Sic matrix processing steps established for the flat panels, SiC/SiC tubes were fabricated with wall thicknesses of approximately 60 mils and total fiber fractions of approximately 35%. The "D" split ring tests for hoop tensile properties, micro-structural examinations for relationship between fiber architecture formation and matrix infiltration, and the low-pressure burner rig tests for the high temperature durability under thru-thickness thermal gradient were conducted. The better matrix infiltration and higher hoop strength were achieved using the tri-axial braided and the three-float pin woven SiC/SiC tubes. In general, it needs not only higher hoop direction fibers but also axial direction fibers for the higher hoop strength and the better infiltration, respectively. These results are analyzed to offer general guidelines for selecting fiber pre-form architectures and SiC/SiC processes that maximize tube hoop strength, thru-thickness thermal conductivity, and burner-rig durability under a high thermal gradient.

Yun, H. M.↗

NASA NTRS2011

Microwave Tissue Soldering for Immediate Wound Closure

A novel approach for the immediate sealing of traumatic wounds is under development. A portable microwave generator and handheld antenna are used to seal wounds, binding the edges of the wound together using a biodegradable protein sealant or solder. This method could be used for repairing wounds in emergency settings, by restoring the wound surface to its original strength within minutes. This technique could also be utilized for surgical purposes involving solid visceral organs (i.e., liver, spleen, and kidney) that currently do not respond well to ordinary surgical procedures. A miniaturized microwave generator and a handheld antenna are used to deliver microwave energy to the protein solder, which is applied to the wound. The antenna can be of several alternative designs optimized for placement either in contact with or proximity to the protein solder covering the wound. In either case, optimization of the design includes the matching of impedances to maximize the energy delivered to the protein solder and wound at a chosen frequency. For certain applications, an antenna could be designed that would emit power only when it is in direct contact with the wound. The optimum frequency or frequencies for a specific application would depend on the required depth of penetration of the microwave energy. In fact, a computational simulation for each specific application could be performed, which would then match the characteristics of the antenna with the protein solder and tissue to best effect wound closure. An additional area of interest with potential benefit that remains to be validated is whether microwave energy can effectively kill bacteria in and around the wound. Thus, this may be an efficient method for simultaneously sterilizing and closing wounds. Using microwave energy to seal wounds has a number of advantages over lasers, which are currently in experimental use in some hospitals. Laser tissue welding is unsuitable for emergency use because its large, bulky equipment cannot be easily moved between operating rooms, let alone relocated to field sites where emergencies often occur. In addition, this approach is highly dependent on the uniformity and thickness of the protein solder as well as the surgeon s skills. In contrast, the use of microwave energy is highly tolerant of the thickness of the protein solder, level of fluids in and around the wound, and other parameters that can adversely affect the outcome of laser welding. However, controlling the depth of penetration of the microwave energy into the wound is critical for achieving effective wound sealing without damaging the adjacent tissue. In addition, microspheres that encapsulate metallic cores could also be incorporated into the protein solder to further control the depth of penetration of the microwave energy.

Arndt, G. Dickey↗

NASA NTRS2011

Microwave Tissue Soldering for Immediate Wound Closure

Arndt, G. Dickey↗

DOE OSTI2023

From Hydrometeor Size Distribution Measurements to Projections of Wind Turbine Blade Leading-Edge Erosion

Wind turbine blade leading-edge erosion (LEE) is a cause of increased operation and maintenance costs and decreased annual energy production. Thus, detailed, site-specific quantification of likely erosion conditions are critically needed to inform wind plant owner/operator decisions regarding mitigation strategies. Estimating the damage potential at a wind plant site requires accurate measurement of precipitation intensity, phase, droplet size distributions, wind speeds and their joint statistics. The current work quantifies the effect of disdrometer type on the characterization of LEE potential at a site in the US Southern Great Plains. using observations from three co-located disdrometers (an optical, an impact and a video disdrometer), along with hub-height wind-speed observations from a Doppler lidar and two LEE models: a kinetic energy model and the Springer model. Estimates of total kinetic energy of hydrometeor impacts over the four-year study period vary by as much as 38%, and coating lifetime derived from accumulated distance-to-failure estimates from the Springer model differ by an even greater amount, depending on disdrometer type. Damage potential at this site is concentrated in time, with 50% of impact kinetic energy occurring in 6–12 h per year, depending on which set of disdrometer observations is used. Rotor-speed curtailment during the most erosive 0.1–0.2% of 10 min periods is found to increase blade lifetimes and lead to the lowest levelized cost of energy.

17 WIND ENERGY↗

NASA NTRS1980

Characteristics of edge breakdowns on Teflon samples

The characteristics of electrical discharges induced on silverbacked Teflon samples irradiated by a monoenergetic electron beam have been studied under controlled laboratory conditions. Measurements of breakdown threshold voltages indicate a marked anisotropy in the electrical breakdown properties of Teflon: differences of up to 10 kV in breakdown threshold voltage are observed depending on the sample orientation. The material anisotropy can be utilized in spacecraft construction to reduce the magnitude of discharge currents.

Yadlowsky, E. J.↗