Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “binder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Development of a Printable Prill Formulation Technique and Demonstration of Monomodal Prill Size on Compaction Density and Compressive Strength

Polymer-bonded explosive molding powder, or “prills,” are relied on for the fabrication of pressed high explosives since the 1950's. The wet granulation technique, also known as “slurry coating,” that is used to formulate prills, is a complex process that results in polydisperse and variable yields. This makes it difficult to study the mesoscale effect that prills have on the microstructure of a pressed article. The following study introduces a novel approach to energetic granulation that leverages techniques used in the additive manufacturing of paste-like energetic materials. This extrusion granulation, or prill printing technique, makes it possible to tailor the sizes and shapes of prills, allowing for their morphological influences to be studied in a controlled manner. The following work details the fabrication and characterization of four monomodal size lots of prills using an inert formulation (95 wt.% melamine, 5 wt.% polymer binder). Prills from each size lot were die-pressed using a fixed recipe to investigate how prill size impacts compaction density and therefore compressive strength. It was found that larger prills influence the pressing density by creating larger defects within the microstructure of a pressed article, resulting in a decrease in compressive strength.

direct ink write↗

Modeling The Effects of Shock Pressure and Pore Morphology on Hot Spot Mechanisms in HMX

Here, we investigate the effects of shock pressure and pore morphology on the formation and growth of hot spots in HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine). Both non-reactive and reactive ALE3D simulations are used in these studies. Our non-reactive simulations show a viscous-dominated pore collapse mode at lower shock pressures (2–10 GPa) with shear band formation and a hydrodynamic-dominated mode at higher shock pressures (20-40 GPa) due to bulk melting. When normalized by bulk shock heating, viscous-dominated pore collapse modes are more efficient at generating hot spots. Pore morphology influences the post-collapse temperature distributions and reaction rate for a fixed pore area and shock pressure. We find that multiple surface pores at the binder-grain interface tend to react the fastest. Due to their upstream location in the HMX grain, the surface pores collapse sooner than interior pores; thus, the extent of reaction will generally favor these morphologies because they have more time to grow. In general, multiple smaller hot spots tend to react faster than a single larger hot spot because they accelerate one another's burning. The rank order of morphology effects, however, is not the same for non-reactive and reactive simulations. For example, while multiple surface pores produce the highest reaction rates they do not produce the highest (non-reactive) hot spot temperatures. In conclusion, our numerical studies provide insights on hot spot mechanisms in lieu of direct measurements and can be used to develop advanced shock initiation models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and Evaluation of 3-Picrylamino-1,2,4-Triazole (PATO) Formulations

3–Picrylamino–1,2,4–triazole (PATO) is a thermally stable explosive invented at Los Alamos National Laboratory (LANL) almost half a century ago. Despite a rapid and high yielding synthesis, performance data for this promising explosive are scant. We prepared material using Coburn's synthesis, and discovered that the particle size distribution and morphology leads to difficulty in pressing formulations to high density. Three formulations were made using glycidyl azide polymer (GAP), FK–800, and Estane 5703/nitroplasticizer (NP) as binders. The maximum pressed density of these formulations was 89 % of theoretical maximum density (TMD). We determined detonation velocity and, for the FK–800 formulation, detonation pressure. Furthermore, the performance of PATO is similar to TATB at equivalent pressed density.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hot Spot Chemistry in Several Polymer-Bound Explosives under Nanosecond Shock Conditions

Initial hot spot temperatures and temperature evolutions for 4 polymer-bound explosives under shock compression by laser-driven flyer plates at speeds from 1.5–4.5 km s -1 are presented. A new averaging routine allows for improved signal to noise in shock compressed impactor experiments and yields temperature dynamics which are more accurate than has been previously available. The PBX formulations studied here consist of either pentaerythritol tetranitrate (PETN), 1,3,5-trinitro-1,3,5-triazinane (RDX), 2,4,6-trinitrotoluene (TNT), or 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) in a 80/20 wt.% mixture with a silicone elastomer binder. The temperature dynamics demonstrate a unique shock strength dependence for each base explosive. The initial hot spot temperature and its evolution in time are shown to be indicative of chemistry occurring within the reaction zone of the four explosives. The number density of hot spots is qualitatively inferred from the spatially-averaged emissivity and appears to increase exponentially with shock strength. An increased emissivity for formulations consisting of TNT and TATB is consistent with carbon-rich explosives and in increased hot spot volume. Finally, qualitative conclusions about sensitivity were drawn from the initial hot spot temperature and rate at which the number of hot spots appear to grow.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Coefficient of Thermal Expansion during Ratchet Growth of TATB Compactions

Triamino trinitrobenzene (TATB) is an insensitive high explosive, meaning that it is quite immune from accidental detonation and only performs in appropriately engineered configurations. While this is advantageous for applications, the TATB crystal is graphitic and possesses significant thermal and mechanical anisotropy. Compactions of TATB crystals, with or without binder, have been shown to have oriented TATB crystals that relate to the pressing geometry and process, and this TATB texture necessarily imparts microscale and macroscale anisotropy to the compaction. By a mechanism not fully understood, thermal cycling results in irreversible volume expansion (also called ratchet growth) of the compaction likely by creating stress points on the microscale. Changes in density caused by thermal cycling can certainly effect the explosive performance. Our past characterization of the ratchet growth phenomenon has focused on the magnitude of the irreversible strain as measured before and after a thermal cycle. Finally, in the work presented here, we analyze the evolving thermal expansion behavior during the ascending and descending temperature ramps, providing further insight into the material changes taking place during the ratchet growth phenomenon.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Cookoff of Powdered and Pressed Explosives using a Micromechanics Pressurization Model

Cookoff experiments of powdered and pressed TATB-based plastic bonded explosives (PBXs) have been modeled using a pressure-dependent universal cookoff model (UCM) in combination with a micromechanics pressurization (MMP) model described in a companion paper. The MMP model is based on the accumulation of decomposition gases at nucleation sites that load the surrounding TATB crystals and binder. This is the first cookoff model to use an analytical mechanics solution for compressibility and thermal expansion to describe internal pressurization caused by both temperature and decomposition occurring within closed-pore explosives. This approach produces more accurate predictions of ignition time and pressurization within high-density explosives than simple equation-of-state models. The current paper gives details of the reaction chemistry, model parameters, predicted uncertainty, and validation using experiments from multiple laboratories with errors less than 6 %. The UCM/MMP model framework gives more accurate thermal ignition predictions for high density explosives that are initially impermeable to decomposition gases.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Segmentation of RDX and TNT in X‐Ray Computed Tomography Reconstructions of Melt‐Cast Explosives

ABSTRACT Three‐dimensional mesoscale characterization of heterogeneous melt‐cast high explosives is challenging because of the difficulty differentiating binder from explosive crystals: two functionally different materials which are typically similar in density by design. Here, we report an algorithm which can differentiate hexahydro‐1,3,5‐trinitro‐1,3,5‐triazine (RDX) from 2,4,6‐trinitrotoluene (TNT) in x‐ray computed tomography (CT) volumes with tens of microns resolution. This method allows us to quantify RDX/TNT content, porosity, and RDX domain size. We calibrated the segmentation algorithm using simulated x‐ray CT volumes containing object models of RDX crystals within a TNT matrix. We then segmented and analyzed CT data for Composition B (Comp B), a 60/40 RDX/TNT mixture, and Cyclotol, a 75/25 RDX/TNT mixture. We examined melt‐cast samples fabricated with 100% theoretical maximum density (TMD) and 85% TMD. For the 100% TMD Comp B and Cyclotol samples, the RDX content values calculated by segmentation were 3% and 9% lower, respectively, than the values measured by high‐performance liquid chromatography on material from the same synthesis lots. This result is consistent with the expected underreporting of RDX content resulting from x‐ray CT resolution limits on RDX particles with diameters smaller than 25 µm. The 85% TMD samples were less accurately segmented with our algorithm due to the confounding presence of voids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Extrusion‐Spheronization of Mock Energetic Materials

The primary method for producing plastic bonded explosive (PBX) granules, or “prills”, has remained relatively unchanged for 70 years despite the complex nature of the process. In this work, we demonstrate the feasibility of using an extrusion‐spheronization technique to produce prills for PBX applications. We begin by detailing an inert formulation with similar properties of PBXs and then demonstrate the extrusion‐spheronization processing of these materials. A study is then performed where the spheronization process time of the extruded materials is varied and the resultant prills are morphologically characterized. Further, these prills are then pressed into high‐density articles and subject to compression testing to elucidate trends in process, properties, and performance. It was found that, for our formulation (95 wt.% melamine/5 wt.% polymer binder) and process, a spheronization time of 60 s yielded relatively uniform particles that exhibited improved poured, tapped, and pressed densities. Mechanical strength did not have a strong trend with process time as all spheronized materials had similar peak compression stress at failure. After further optimization, extrusion‐spheronization may be a promising path for future PBX formulation.

extrusion spheronization↗

Extrusion‐Spheronization of Energetic Materials

The prevailing method to produce plastic‐bonded explosive (PBX) molding powder, or “prills”, is a complex, multiphase, and bespoke process that was developed by the high explosives (HEs) manufacturing industry several decades ago. This work demonstrates the utility of a simpler, widely‐used mechanical process—extrusion‐spheronization—to produce PBX prills. We begin by detailing precautions taken to enable safe remote operation of extrusion‐spheronization equipment with HE. We then perform a study investigating the effect of lacquer solvent composition on the particle packing, pressed density, and compressive strength properties of a 95 wt.% TATB/5 wt.% polymer binder formulation akin to PBX 9502. It was found that increased composition of low vapor pressure solvents caused prolonged retention of the solvent, resulting in tackier materials that would agglomerate and form larger prills. The larger prills also led to lower poured density and tapped density of HE prills and compressive strength of pressed PBX articles. The samples prepared with a 75% propyl acetate/25% butyl acetate lacquer solvent composition exhibited the highest compressive strength. However, it is believed that the prill packing and compressive strength properties are primarily driven by the prill size rather than the chemical composition of the lacquer itself. Extrusion‐spheronization remains a promising method to reliably and repeatably produce HE prills that is less sensitive to feedstock or process variation than traditional methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Silicon‐Based Anodes for Lithium‐Ion Batteries: From Fundamentals to Practical Applications

Abstract Silicon has been intensively studied as an anode material for lithium‐ion batteries (LIB) because of its exceptionally high specific capacity. However, silicon‐based anode materials usually suffer from large volume change during the charge and discharge process, leading to subsequent pulverization of silicon, loss of electric contact, and continuous side reactions. These transformations cause poor cycle life and hinder the wide commercialization of silicon for LIBs. The lithiation and delithiation behaviors, and the interphase reaction mechanisms, are progressively studied and understood. Various nanostructured silicon anodes are reported to exhibit both superior specific capacity and cycle life compared to commercial carbon‐based anodes. However, some practical issues with nanostructured silicon cannot be ignored, and must be addressed if it is to be widely used in commercial LIBs. This Review outlines major impactful work on silicon‐based anodes, and the most recent research directions in this field, specifically, the engineering of silicon architectures, the construction of silicon‐based composites, and other performance‐enhancement studies including electrolytes and binders. The burgeoning research efforts in the development of practical silicon electrodes, and full‐cell silicon‐based LIBs are specially stressed, which are key to the successful commercialization of silicon anodes, and large‐scale deployment of next‐generation high energy density LIBs.

Feng, Kun↗

Additive‐Free Aqueous MXene Inks for Thermal Inkjet Printing on Textiles

Abstract Direct printing of functional inks onto flexible substrates allows for scalable fabrication of wearable electronics. However, existing ink formulations for inkjet printing require toxic solvents and additives, which make device fabrication more complex, limit substrate compatibility, and hinder device performance. Even water‐based carbon or metal nanoparticle inks require supplemental surfactants, binders, and cosolvents to produce jettable colloidal suspensions. Here, a general approach is demonstrated for formulating conductive inkjet printable, additive‐free aqueous Ti 3 C 2 T x MXene inks for direct printing on various substrates. The rheological properties of the MXene inks are tuned by controlling the Ti 3 C 2 T x flake size and concentration. Ti 3 C 2 T x ‐based electrical conduits and microsupercapacitors (MSCs) are printed on textile and paper substrates by optimizing the nozzle geometry for high‐resolution inkjet printing. The chemical stability and electrical properties of the printed devices are also studied after storing the devices for six months under ambient conditions. Current collector‐free, textile‐based MSCs show areal capacitance values up to 294 mF cm −2 (2 mV s −1 ) in poly(vinyl alcohol)/sulfuric acid gel electrolyte, surpassing reported printed MXene‐based MSCs and inkjet‐printed MSCs using other 2D nanomaterials. This work is an important step toward increasing the functional capacity of conductive inks and simplifying the fabrication of wearable textile‐based electronics.

Uzun, Simge↗

Polycarbonate‐Based Solid‐Polymer Electrolytes for Solid‐State Sodium Batteries

Solid-polymer electrolytes comprised of polypropylene carbonate (PPC) and varied sodium bis(fluorosulfonyl)imide (NaFSI) salt concentrations are investigated for implementation as a conductive solid polymer electrolyte into solid-state cathode composites utilizing a sodium-layered oxide active material. The ionic conductivity generally increases with NaFSI salt content, reaching ≈1 mS cm −1 at 80 °C at the highest salt concentration (PPC:NaFSI = 0.5:1). Through an all-in-one slurry casting method, Na 2/3 Ni 1/3 Mn 2/3 O 2 cathode composites are fabricated in which the dispersed PPC electrolyte acts as the primary binder. Enabled by a bilayer polymer electrolyte system, cycling performance with the PPC cathode electrolyte is optimized with respect to salt concentration and anode material. The best cyclability is achieved with a moderate salt concentration electrolyte (PPC:NaFSI = 5:1), showcasing an initial capacity of 83 mA h g −1 with a remarkable 80% capacity retention after 150 cycles at C/5 rate and 60 °C. The superior performance of the lower salt concentration electrolyte is attributed to better electrochemical stability, as confirmed by linear sweep voltammetry and online electrochemical mass spectrometry measurements. In conclusion, these results underscore the potential of carbonate-based polymer electrolytes and the importance of balancing electrolyte conductivity and stability in cell design.

25 ENERGY STORAGE↗

Stable Cycling with Intimate Contacts Enabled by Crystallinity–Controlled PTFE–Based Solvent–Free Cathodes in All–Solid–State Batteries

All-solid-state batteries (ASSBs) employing Li-metal anodes and inorganic solid electrolytes are attracting great attention due to high safety and energy density for next-generation energy storage devices. However, the volume change of cathode active materials can cause contact loss, resulting in charge carrier isolation, heterogeneous current distribution, and poor electrochemical properties in ASSBs. Here, a simple, yet effective, solvent-free electrode engineering approach with polytetrafluoroethylene (PTFE) as a binder for ASSBs is reported, enabling intimate contact and stable interfaces with the cathode. It is substantiated that the crystallinity of PTFE can be controlled depending on the heat history, and highly crystalline PTFE displays robust mechanical properties. High-nickel LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode prepared with crystalline PTFE show improved cycle and rate performances in ASSBs. In addition, it is revealed that the intimate contact between cathode particles with a stable cathode electrolyte layer is maintained during cycling by postmortem studies. Furthermore, this simple engineering method can be applied to prepare cathodes with a variety of active materials and solid electrolytes in ASSBs.

25 ENERGY STORAGE↗

Structure of Shock Waves and Inelasticity in Shock-Compressed Cemented Tungsten Carbides

In this study, shock wave experiments are conducted on General Carbide cemented tungsten carbide with 3.7wt.% cobalt binder to determine its shock-induced compression behavior up to 100 GPa. The measured wave profiles indicate the cemented tungsten carbide to undergo elastic-plastic deformation during shock compression. A three-stage particle velocity profile is observed in the experiments -- an initial elastic-rise to the Hugoniot Elastic Limit (HEL), an elastic-plastic ramp indicating substantial post-yield hardening, and finally a rise to the peak shocked Hugoniot state. The results of the experiments are used to determine the HEL, the shock velocity (U s ) vs. particle velocity (u p ) Hugoniot relation, and the longitudinal stress (σ x ) vs. specific volume (V) curve for the samples. The HEL of the material was determined to lie between 4.41 GPa and 4.58 GPa. The U s - u p relation was determined to be U s = 4.97 + 1. 457u p for particle velocities greater than 0.75 km/s. The measured plastic shock velocities for particle velocities less than 0.7 km/s were found to be larger than those predicted using the linear U s - u p Hugoniot relationship, indicating the cemented WC samples to preserve substantial shear strength in the post-yield deformation region. No phase transformation was observed up to 100 GPa.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Accelerating Battery Simulations by Using High Performance Computing and Opportunities with Machine Learning

The US Department of Energy (DOE) estimates that the battery pack cost of $60 per kilowatt-hour while increasing the driving range to over 300 miles and vehicle charging under 15 min or less would enable mass penetration of electric vehicles in the USA by 2030. These projections are based on the currently available high-density cell chemistry combined with a system level design and optimized electrodes. Electrodes for current state-of-the-art lithium-ion cell technology are fabricated from electrode slurry comprising of active material, polymeric binder, and conductive diluent such as carbon black that are coated on metal current collectors such as copper and aluminum. Given these challenging requirements for development of electrical energy storage devices for future transportation needs, a predictive simulation capability which can accelerate design by considering performance and safety implications of different geometry, materials, and chemistry choices is required. In this chapter, we discuss our state-of-the-art three-dimensional modeling framework, providing examples on battery performance and safety simulations. We also present approaches to use machine learning in the context of large datasets that are becoming available.

Allu, Srikanth↗

Additive Manufacturing – A New Challenge for Automation and Robotics

Additive manufacturing (AM) is a rapidly growing technology descended from the first stereolithography systems. AM describes a variety of material deposition technologies for forming objects in a digital manner layer-by-layer under computer control. Now commonly known as 3D printing, AM quickly branched out into several key directions – material extrusion, sheet lamination, direct energy deposition, vat polymerization, powder bed fusion, binder jetting, and material jetting. The common factor in all AM branches is a foundation in robotics and automation. While most of the mechanical 3D printing structures are based on simple gantry systems, there are Gough-Stewart platforms and, more recently, six or more DoF manipulator-based systems that have been developed. Currently available commercial systems are based on open-loop control with minimum sensing capabilities; the latest systems in development are starting to take advantage of complex feedback loops and layers of advanced sensing and data logging. The Manufacturing Demonstration Facility of Oak Ridge National Laboratory is leading the efforts in applying advanced robotics in the creation of large-scale 3D printers. The recent demonstration of an additively manufactured excavator at the CONEXPO 2017 exhibition in Las Vegas showed that the use of cutting edge robotics and automation is essential for the next generation of additive systems. The future of AM will heavily rely on advanced robotics, machine learning, and the internet of things. This paper summarizes progress in AM; presents the practical aspects, challenges, and lessons learned in developing robotic-based AM systems; and outlines the needs and future directions of robotics for AM.

Nycz, Andrzej↗