Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SALTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Molten salt electrolysis and room temperature ionic liquid electrochemical processes for refining rare earth metals: Environmental and economic performance comparison

Circularizing end of life products such as electronic waste can open a new source for rare earth elements (REEs) that will decrease the demand pressure on conventional virgin production. The last step to produce REEs consists of a refining process to convert rare earth oxide (REO) to REE metal. One promising technology is processing REO via a room temperature ionic liquid, which is characterized by low energy requirements in contrast to existing REEs extraction processes. In this work, life cycle and techno-economic assessments are performed and compared against molten salt electrolysis. Here, the results show that both processes have advantages and disadvantages in terms of environmental performance, and that they are similarly competitive in terms of economic performance. A breakeven analysis suggests that future research should focus on coupling the production of REOs with the refining processes to attempt to lower REO cost and make them economically feasible in the U.S.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

An additively-manufactured molten salt-to-supercritical carbon di-oxide primary heat exchanger for solar thermal power generation – Design and techno-economic performance

The design and techno-economic performance of a compact additively manufactured (AM) molten salt (MS)-to-supercritical carbon di-oxide (sCO2) primary heat exchanger (PHE) for solar thermal application is described. The PHE design consists of sCO2 flow through an array of microscale pin fins while the MS flows through mm-scale rectangular channels. Constraints imposed by AM using laser powder bed fusion method are considered in the design. Structural and fluid flow simulations are performed to arrive at a viable design of the core and headers. A simplified one-dimensional steady state model for the PHE is developed including the impact of surface roughness from the AM process. A process-based cost model is used to determine the tradeoff between thermofluidic design and manufacturing cost. A parametric study is performed using the thermo-fluidic and cost models to determine the set of geometrical and flow variables that result in high power density and low cost, while restricting the pressure drop on the sCO2 side to less than 2% of line pressure. Flow rates of MS and sCO2 were varied over heat capacity rate ratios ranging from 0.2 to 1. Results indicate that it is possible to design a low-pressure drop AM PHE with an effectiveness of 90% and a power density in excess of 10 MW/m3 (including headers). Fabrication of representative nickel superalloy specimens are shown to demonstrate that low-porosity parts with the requisite dimensional tolerance of PHE core can be generated.

14 SOLAR ENERGY↗
DOE OSTI2022

Convective heat transfer and friction factor characteristics of molten salts in spirally fluted tubes

Spirally fluted tubes have been widely used for heat exchangers due to their superior heat transfer enhancement. However, most of the previous studies focused on the effects of a limited number of geometric parameters, i.e., the flute pitch and flute depth, on convective heat transfer and friction factor characteristics of low-Prandtl-number fluids, i.e., air and water. The correlations developed in these studies may not be accurate or applicable for medium-Prandtl-number fluids, such as molten salts. A numerical analysis using a Computational Fluid Dynamics (CFD) tool, STAR–CCM+, is therefore carried out in this study to systematically investigate the effects of four geometric parameters, including the flute pitch ρ, flute depth e, flute start number N s (or flute helix angle θ), and trough length L tr on convective heat transfer and friction factor characteristics of a medium-Prandtl-number fluid, FLiNaK (46.5LiF-11.5NaF-42KF mol %), in spirally fluted tubes. Additionally, the convective heat transfer and Darcy friction factor correlations are proposed and validated, with ± 20% uncertainties, for medium-Prandtl-number fluids under the following conditions: Re = 88–1600, Pr = 2.5–40, ρ/D c = 0.44–3.51, e/D c = 0.10–0.40, θ/90= 0.20–0.81, and L tr /D c = 0.71–2.16. The correlations proposed help improve the design of spirally fluted-tube heat exchangers.

42 ENGINEERING↗
DOE OSTI2023

Understanding the reversible electrodeposition of aluminum in low-cost room-temperature molten salts

Aluminum is the most earth-abundant metal, trivalent, and inert in ambient air; it also has a density approximately five times that of lithium at room temperature, making it attractive for cost-effective, long-duration storage in batteries. Here, we investigate structural requirements and physicochemical and transport properties of ionic liquid (IL) electrolytes thought to enable high reversibility of Al battery anodes. We find that intentionally designed, low-cost IL analogs, including ammonium-based molten salts, offer comparable Al anode reversibility to state-of-the-art imidazolium-based IL melts. A critical ratio of solvated Al-ion species is required to balance the effects of Lewis acidity needed to continuously etch native Al 2 O 3 and form a stable solid electrolyte interphase on Al. Our findings open new opportunities for developing simple, cost-effective, room-temperature Al batteries that enable long-duration electrical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2020

Controlling the Interface between Salts, Solvates, Co-crystals, and Ionic Liquids with Non-stoichiometric Protic Azolium Azolates [Plus Supporting Information]

In this work, a non-stoichiometric approach to control the solid-state behavior of protic ionic liquids (PILs) was demonstrated by direct mixing of 4,5-dicyanoimidazole (HDCNim) with either 1-ethylimidazole (C 2 im) or 1-butylimidazole (C 4 im) in different mole fractions. Isolation and characterization of three crystalline materials (all having melting points < 100 °C, thus fitting the PIL definition) revealed three different but closely related systems. The structure of [HC 2 im][DCNim] consists of a confused proton system, which is so named for the fast proton exchange between basic and acidic fragments and the formation of hydrogen-bonded anionic oligomers. The compound [HC 2 im][DCNim]·HDCNim consists of an oligomeric delocalized anion (a confused proton located between two azole fragments, in which one acts as a neutral moiety while the other as an ionic fragment, DCNim-H-DCNim) and [HC 4 im][DCNim]·HDCNim can be classified as a salt co-crystal. We believe that these observations will allow a deeper understanding of the behavior of “confused protons” and provide additional strategies for controlling the properties of important classes of materials such as active pharmaceutical ingredients.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Reaction Mechanism of the Synthesis of a Disordered Rock Salt Cathode Material

Li-rich disordered rock salt (DRX) materials have recently emerged as a class of promising cathode materials for cobalt- and nickel-free Li-ion batteries that can achieve a high energy density and high electrochemical storage capacity. Here, the synthesis conditions of DRX were found to have a significant impact on the electrochemical performance of the final product formed and hence need to be carefully controlled. To date, the formation pathway of DRX materials has remained largely unexplored. In this work, the phase evolution of a DRX material, Li 1.1 Mn 0.8 Ti 0.1 O 1.9 F 0.1 (LMTF1811), during solid-state synthesis, was monitored using in situ synchrotron X-ray diffraction (sXRD). We have observed several crystalline intermediates formed during the synthesis process before the full formation of DRX. Ex situ X- ray absorption spectroscopy (XAS) was used to assess the local structure and charge states of the transition metals. F K-edge XAS collected from the final product LMTF1811 shows that the degree of F incorporation into the DRX phase is low.

Diffraction↗
DOE OSTI2022

Volatilized Molten Salts: An Alternative Avenue for Synthesizing Single-Phase Perovskites

Single phase La 0.8 Sr 0.2 MnO 3 (LSM) and core-shell La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF)-LSM have been synthesized using a volatilized mol-ten salt synthesis (vMSS) method for the first time with a LiCl-KCl eutectic. While deleterious to LSM formation when the MSS takes place in the liquid phase, LiCl-KCl eutectic successfully facilitates LSM formation when volatilized. Specifically, KCl evaporates before LiCl and promotes formation of LSM via the gaseous phase. As time progresses, LiCl volatilizes and contributes negatively to Sr retention in the perovskite phase in accordance with Lux-Flood chemistry and to product phase purity. The vMSS is therefore a way to obviate the more immediate restrictions of Lux-Flood chemistry in the liquid phase. LiCl-KCl eutectic can also be used to successfully synthesis core-shell LSCF-LSM nanoparticles in times as short as 1 hour at 600 °C. These results demonstrate the surprising versatility and flexibility of the MSS method to synthesize numerous potential energy relevant materials with greater ease than previously thought.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Influence of Nd(II) and Nd(III) Ions on the Speciation and Kinetic Dynamics of Radiolytic Transients in Molten LiCl-KCl Eutectic Salt Mixtures

In the pyrochemical reprocessing of used nuclear fuel, understanding the effects of ionizing radiation on the chemical behavior of fission products in molten chloride eutectic salt is crucial. Here, this study investigates the impact of radiation on the chemical and kinetic speciation of Nd ions in molten LiCl-KCl eutectic, which are challenging to separate due to their multivalent oxidation states and comproportionation reactions. Electron pulse radiolysis techniques were used to determine transient absorption spectra, chemical kinetics, and activation parameters for the reaction of Nd ions with the primary products of molten LiCl-KCl eutectic radiolysis: the solvated electron (e S - ) and dichlorine radical anion (Cl 2 •- ). Initially, Nd(III) reacted rapidly with e S - , forming Nd(II) with a second-order rate coefficient of k = (4.54 ± 0.07) × 10 10 M -1 s -1 at 673 K. The resulting Nd(II) ions then reacted slowly with Cl 2 •- , regenerating Nd(III) with an estimated rate of k = (1.72 ± 0.04) × 10 10 M -1 s -1 at 673 K. Additionally, the comproportionation reaction of Nd(III) and Nd(s) to form Nd(II) was monitored chemically and electrochemically. This work suggests that the comproportionation reaction of Nd(III) with Nd(s) to form Nd(II) is unstable in molten LiCl-KCl eutectic.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

Critical Role of Anion–Solvent Interactions for Dynamics of Solvent-in-Salt Solutions

Most polar solvent molecules are unstable toward electrode materials used in Li-based batteries. Solid electrolytes and ionic liquids are far more stable; however, they have relatively low conductivity, and therefore electrical energy storage devices based on them would suffer from low power. Solvent-in-salt (SIS) systems combine chemical stability with relatively high conductivity. Here, we show how the nature of the employed anion affects the structure and dynamics of SIS systems. The transport of ions in lithium bis(fluorosulfonyl)imide (Li-FSI) systems was determined to be always faster than that in lithium bis(trifluoromethanesulfonyl)imide (Li-TFSI) systems. Moreover, we found that viscosity does not solely control conductivity and that the lower conductivity of TFSI – solutions is related to their stronger interaction with the solvent. This restricts solvent dynamics and slows down ion motions compared to that of FSI – . Interestingly, the TFSI–solvent interaction also leads to better charge separation (weaker ion–ion correlations) and a higher transference number for Li. Finally, our results suggest that the ability to tune the solvent network formed around the anions may further improve electrolyte conductivity and Li transference number for safer and more efficient energy storage devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Asymmetric Composition of Ionic Aggregates and the Origin of High Correlated Transference Number in Water-in-Salt Electrolytes

"Water-in-salt" electrolytes open up exciting new avenues for expanding the electrochemical window of aqueous electrolytes. We investigated the solvation structure and dynamics of highly concentrated lithium bis(trifluoromethane)sulfonimide aqueous electrolyte using experimentally corroborated molecular dynamics simulations. The simulations revealed that the heterogeneous structure of the electrolyte comprises percolating networks of ion and water domains/aggregates. Interestingly, the ionic regions are composed of more TFSI - ions than Li + ions. The Li + -ion transport mechanism was further explored. Li + ions can hop along the coordinated TFSI- ions in the ionic aggregates. The calculated correlated transference number of the 20 m electrolyte is similar to 0.32, which is reasonably high for the high concentration due to a weak negative correlation between the motion of cations and anions within the heterogeneous microscopic domains. These molecular dynamics results connect the heterogeneous structure of the electrolyte to the correlated dynamics of the Li + ion and provide a new understanding of the Li + -ion transport mechanism in this novel electrolyte.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Centimeter-Scale Pillared-Layer Metal–Organic Framework Thin Films Mediated by Hydroxy Double Salt Intermediates for CO 2 Sensor Applications

Fabrication of metal–organic framework (MOF) thin films over macroscopic surface areas is a subject of great interest for gas sensor application platforms such as optics and microelectronics. However, a direct synthesis of MOF films at ambient conditions, in particular pillared-layer MOF films due to their anisotropic structures, remains a significant challenge. Herein, we demonstrate for the first time a facile construction of dense and continuous pillared-layer MOF thin films on a centimeter scale via an aluminum-doped zinc oxide template and hydroxy double salt (HDS) intermediates at room temperature. A series of Cu(II)-based pillared MOFs with different 1,4-benzenedicarboxylic acid (bdc) ligands were explored for optimizing MOF film formation for CO 2 sensor applications. Nonpolar ligands with lower water solubility preferentially formed crystalline pillared MOF structures from HDS intermediates. A Cu 2 (ndc) 2 (dabco) (ndc = 1,4-naphthalene-bdc; dabco = 1,4-diazabicyclo[2.2.2]octane) MOF demonstrated the most dense and uniform film growth with micrometer thickness over one square centimeter area. This synthetic approach for growing Cu 2 (ndc) 2 (dabco) MOF thin films was successfully translated toward two sensing platforms: a quartz crystal microbalance and an optical fiber sensor. These Cu 2 (ndc) 2 (dabco) MOF-coated sensors displayed sensitivity toward CO 2 and response/recovery time on the scale of seconds, even at moderate humidity levels. Finally, this work provides a road map for producing continuous and anisotropic crystalline MOF thin films over a centimeter scale area on various substrates, which will greatly facilitate their utilization in MOF-based sensor devices, among other applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A Polymer-in-Salt Electrolyte with Enhanced Oxidative Stability for Lithium Metal Polymer Batteries

Lithium (Li) metal polymer batteries (LMPBs) are a promising candidate of solid-state batteries with high safety. However, rare progress has been demonstrated so far in high voltage stability of polyethylene oxide (PEO) based polymer electrolytes for LMPBs. Herein, we revived the polymer-in-salt electrolyte (PISE) strategy based on the PEO-LiFSI system with EO/Li = 8 through a dry process to avoid the contamination of the residual solvent. The obtained PISEs exhibit quite different morphologies and coordination structures which greatly enhance the oxidative stability of polymer electrolytes. P(EO)1LiFSI has a low melting temperature, a high ionic conductivity at 60 ?C and an oxidative stability of ~4.5 V vs. Li/Li+ (overcoming the inherent low oxidative stability of PEO). With an effective interphase rich in inorganic species, in combination with good stability of the hybrid polymer electrolyte towards Li metal, the cycling stability of Li||LiNi1/3Co1/3Mn1/3O2 is greatly improved. The LMPB can retain 74.4% of capacity after 186 cycles at 60 ?C under the charge cutoff voltage of 4.3 V. The findings point out a promising strategy to develop high-voltage stable polymer electrolytes for high energy-density and safe LMPBs.

Polymer-in-salt electrolyte, lithium metal battery↗
DOE OSTI2023

Effect of Salt Concentration on the Interfacial Solvation Structure and Early Stage of Solid–Electrolyte Interphase Formation in Ca(BH 4 ) 2 /THF for Ca Batteries

The Ca 2+ solvation structure at the electrolyte/electrode interface is of central importance to understand electroreduction stability and solid–electrolyte interphase (SEI) formation for the novel multivalent Ca battery systems. Here, using an exemplar electrolyte, the concentration-dependent solvation structure of Ca(BH 4 ) 2 -tetrahydrofuran on a gold model electrode has been investigated with various electrolyte concentrations via electrochemical quartz crystal microbalance with dissipation (EQCM-D) and X-ray photoelectron spectroscopy (XPS). For the first time, in situ EQCM-D results prove that the prevalent species adsorbed at the interface is CaBH 4 + across all concentrations. As the salt concentration increases, the number of BH 4 – anions associated with Ca 2+ increases, and much larger solvated complexes such as CaBH 4 + ·4THF or Ca(BH 4 ) 3 – ·4THF form at the interface at high concentrations prior to Ca plating. Different interfacial chemistries lead to the formation of SEIs with different components demonstrated by XPS. High electrolyte concentrations reduce the solvent decomposition and promote the formation of thick, uniform, and inorganic-rich (i.e., CaO) SEI layers, which contribute to improved Ca plating efficiency and current density in electrochemical measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Ionic Associations and Hydration in the Electrical Double Layer of Water-in-Salt Electrolytes

Water-in-Salt-Electrolytes (WiSEs) are an exciting class of concentrated electrolytes finding applications in energy storage devices because of their expanded electrochemical stability window, good conductivity and cation transference number, and fire-extinguishing properties. These distinct properties are thought to originate from the presence of an anion-dominated ionic network and interpenetrating water channels for cation transport, which indicates that associations in WiSEs are crucial to understanding their properties. Currently, associations have mainly been investigated in the bulk, while little attention has been given to the electrolyte structure near electrified interfaces. Here, we develop a theory for the electrical double layer (EDL) of WiSEs, where we consistently account for the thermoreversible associations of species into Cayley tree aggregates. The theory predicts an asymmetric structure of the EDL. At negative voltages, hydrated Li + dominates, and cluster aggregation is initially slightly enhanced before disintegration at larger voltages. At positive voltages, when compared to the bulk, clusters are strictly diminished. Performing atomistic molecular dynamics (MD) simulations of the EDL of WiSE provides EDL data for validation and bulk data for parametrization of our theory. Validating the predictions of our theory against MD showed good qualitative agreement. Furthermore, we performed electrochemical impedance measurements to determine the differential capacitance of the studied LiTFSI WiSE and also found reasonable agreement with our theory. Overall, the developed approach can be used to investigate ionic aggregation and solvation effects in the EDL, which, among other properties, can be used to understand the precursors for solid-electrolyte interphase formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Pathways to High-Performance Salt Hydrate Thermochemical Energy Storage Materials and Systems

Thermochemical materials (TCMs) based on salt hydrates are promising for thermal energy storage as they combine high energy densities with low reaction temperatures. However, their adoption is hindered by poor structural integrity and degradation under hygrothermal cycling. Storage performance is governed not only by the chemical reaction, but also by the coupled thermo-chemo-mechanical behavior that evolves with cycling. Understanding and controlling this coupling across length scales (material-to-reactor) is necessary to improve TCM stability and lifetime. In this perspective, we discuss the shortcomings of current characterization approaches and emphasize the need for measuring transport properties and structural transformations using in situ techniques that capture the dynamic evolution of these materials. We also outline opportunities for multiscale modeling frameworks that link thermodynamics and mechanics, enabling predictive evaluation of composite architectures designed for cycling stability. We conclude by identifying research questions that must be addressed to transform TCMs into viable energy storage technologies.

Composites↗
DOE OSTI2025

Photochemical and Cloud and Aerosol Aqueous Contributions to Regionally-Emitted Shipping and Biogenic Non-Sea-Salt Sulfate Aerosol in Coastal California

Aerosol nonsea-salt sulfate (NSS sulfate) forms in the atmosphere by secondary reactions of emissions from marine phytoplankton and shipping, with gas-phase as well as cloud and aerosol aqueous reactions controlling production. Twelve months of Atmospheric Radiation Measurements (ARM) during the Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE) at Scripps Pier in La Jolla, California, showed the highest NSS sulfate mass concentrations occurred for the northwesterly back-trajectories over 64% of the year, with an average of 0.90 μg/m 3 that contributed 76% of annual NSS sulfate concentration. Multiple Linear Regression (MLR) and a refractory black carbon tracer method attributed 76–80% of the regionally emitted sulfur dioxide (SO 2 ) sources of submicron NSS sulfate to marine biogenic emissions and 20–24% to shipping emissions. MLR for oxidation processes explained 21% of the variability with Downwelling Shortwave Radiation (DSW) driving photochemical reactions to account for 34% of annual regional sulfate production, Upwind Cloud Vertical Fraction (UCVF) controlling cloud-associated oxidation to account for 29%, and relative humidity (RH) describing aerosol-phase oxidation to account for 36%. NSS sulfate was correlated moderately to UCVF during April-June and August but to RH in October-January. These findings show the apportionment of SO 2 emissions to biogenic and shipping sources and provide observational constraints for the mechanisms for sulfate production from SO 2 in the atmosphere.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Titanium Carbide MXene Shows an Electrochemical Anomaly in Water-in-Salt Electrolytes

Identifying and understanding charge storage mechanisms is important for advancing energy storage. Well-separated peaks in cyclic voltammograms (CVs) are considered key indicators of diffusion-controlled electrochemical processes with distinct Faradaic charge transfer. Herein, we report on an electrochemical system with separated CV peaks, accompanied by surface-controlled partial charge transfer, in 2D Ti 3 C 2 T x MXene in water-in-salt electrolytes. The process involves the insertion/desertion of desolvation-free cations, leading to an abrupt change of the interlayer spacing between MXene sheets. This unusual behavior increases charge storage at positive potentials, thereby increasing the amount of energy stored. This also demonstrates opportunities for the development of high-rate aqueous energy storage devices and electrochemical actuators using safe and inexpensive aqueous electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗