Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Program Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Application of the direct simulation Monte Carlo method to the full shuttle geometry

A new set of programs has been developed for the application of the direct simulation Monte Carlo (or DSMC) method to rarefied gas flows with complex three-dimensional boundaries. The programs are efficient in terms of the computational load and also in terms of the effort required to set up particular cases. This efficiency is illustrated through computations of the flow about the Shuttle Orbiter. The general flow features are illustrated for altitudes from 170 to 100 km. Also, the computed lift-drag ratio during re-entry is compared with flight measurements.

Bird, G. A.↗
NASA NTRS2011

CFD Simulations of Supersonic Highly Swirling Flow Exiting a Turbine Vane Row Compared with Experimental Observations

Marshall Space Flight Center (MSFC) has been heavily involved in developing the J2-X engine. The Center has been testing a Work Horse Gas Generator (WHGG) to supply gas products to J2-X turbine components at realistic flight-like operating conditions. Three-dimensional time accurate CFD simulations and analytical fluid analysis have been performed to support WHGG tests at MSFC. The general purpose CFD program LOCI/Chem was utilized to simulate flow of products from the WHGG through a turbine manifold, a stationary row of turbine vanes, into a Can and orifice assembly used to control the back pressure at the turbine vane row and finally through an aspirator plate and flame bucket. Simulations showed that supersonic swirling flow downstream of the turbine imparted a much higher pressure on the Can wall than expected for a non-swirling flow. This result was verified by developing an analytical model that predicts wall pressure due to swirling flow. The CFD simulations predicted that the higher downstream pressure would cause the pressure drop across the nozzle row to be approximately half the value of the test objective. With CFD support, a redesign of the Can orifice and aspirator plate was performed. WHGG experimental results and observations compared well with pre-test and post-test CFD simulations. CFD simulations for both quasi-static and transient test conditions correctly predicted the pressure environment downstream of the turbine row and the behavior of the gas generator product plume as it exited the WHGG test article, impacted the flame bucket and interacted with the external environment.

West, Jeff S.↗
NASA NTRS1990

Inflight replanning for diversions

Current procedures for handling flight plan diversions can require too much of the crew's resources. This increases workload and may compromise safety and cause delays in modifying the flight plan. The goal of NASA Langley Research Center's Diverter research program is to develop guidelines for a prototype pilot decision aid for diversions that will reduce cognitive workload, improve safety, increase capacity and traffic flow, and increase aircraft efficiency. The Diverter program has been partitioned into five phases, the first three of which were performed under contract by Lockheed Aeronautical Systems Company, Marietta, GA. In the first two phases, which have been completed, the system requirements and desired functions were defined and a prototype decision-making aid was implemented and demonstrated on a workstation. In phase three, which is currently under way, the pilot/vehicle interface is being defined and the capability of the prototype is being improved. In the last two phases, which will be performed at NASA Langley Research Center, the interface will be implemented, tied into the prototype aiding software, and installed in an advanced simulation facility for testing. In addition, significant implementation issues may be addressed through flight testing on NASA research aircraft. Information is given in viewgraph form.

Palmer, Michael↗
NASA NTRS1973

Calculation of eddy viscosity in a compressible turbulent boundary layer with mass injection and chemical reaction, volume 2

As described in Vol. 1, the eddy viscosity is calculated through the turbulent kinetic energy, in order to include the history of the flow and the effect of chemical reaction on boundary layer characteristics. Calculations can be performed for two different cooling concepts; that is, transpiration and regeneratively cooled wall cases. For the regenerative cooling option, coolant and gas side wall temperature and coolant bulk temperature in a rocket engine can be computed along the nozzle axis. Thus, this computer program is useful in designing coolant flow rate and cooling tube geometry, including the tube wall thickness as well as in predicting the effects of boundary layers along the gas side wall on thrust performances.

Omori, S.↗
NASA NTRS1978

Recent theoretical developments and experimental studies pertinent to vortex flow aerodynamics - With a view towards design

A review is presented of recent progress in a research program directed towards the development of an improved vortex-flow technology base. It is pointed out that separation induced vortex-flows from the leading and side edges play an important role in the high angle-of-attack aerodynamic characteristics of a wide range of modern aircraft. In the analysis and design of high-speed aircraft, a detailed knowledge of this type of separation is required, particularly with regard to critical wind loads and the stability and performance at various off-design conditions. A description of analytical methods is presented. The theoretical methods employed are divided into two classes which are dependent upon the underlying aerodynamic assumptions. One conical flow method is considered along with three different nonconical flow methods. Comparisons are conducted between the described methods and available aerodynamic data. Attention is also given to a vortex flow drag study and a vortex flow wing design using suction analogy.

Lamar, J. E.↗
NASA NTRS1993

Computerized atmospheric trace contaminant control simulation for manned spacecraft

Buildup of atmospheric trace contaminants in enclosed volumes such as a spacecraft may lead to potentially serious health problems for the crew members. For this reason, active control methods must be implemented to minimize the concentration of atmospheric contaminants to levels that are considered safe for prolonged, continuous exposure. Designing hardware to accomplish this has traditionally required extensive testing to characterize and select appropriate control technologies. Data collected since the Apollo project can now be used in a computerized performance simulation to predict the performance and life of contamination control hardware to allow for initial technology screening, performance prediction, and operations and contingency studies to determine the most suitable hardware approach before specific design and testing activities begin. The program, written in FORTRAN 77, provides contaminant removal rate, total mass removed, and per pass efficiency for each control device for discrete time intervals. In addition, projected cabin concentration is provided. Input and output data are manipulated using commercial spreadsheet and data graphing software. These results can then be used in analyzing hardware design parameters such as sizing and flow rate, overall process performance and program economics. Test performance may also be predicted to aid test design.

Perry, J. L.↗
NASA NTRS1996

Droplet Deformation in an Extensional Flow: The Role of Surfactant Physical Chemistry

Surfactant-induced Marangoni effects strongly alter the stresses exerted along fluid particle interfaces. In low gravity processes, these stresses can dictate the system behavior. The dependence of Marangoni effects on surfactant physical chemistry is not understood, severely impacting our ability to predict and control fluid particle flows. A droplet in an extensional flow allows the controlled study of stretching and deforming interfaces. The deformations of the drop allow both Marangoni stresses, which resist tangential shear, and Marangoni elasticities, which resist surface dilatation, to develop. This flow presents an ideal model system for studying these effects. Prior surfactant-related work in this flow considered a linear dependence of the surface tension on the surface concentration, valid only at dilute surface concentrations, or a non-linear framework at concentrations sufficiently dilute that the linear approximation was valid. The linear framework becomes inadequate for several reasons. The finite dimensions of surfactant molecules must be taken into account with a model that includes surfaces saturation. Nonideal interactions between adsorbed surfactant molecules alter the partitioning of surfactant between the bulk and the interface, the dynamics of surfactant adsorptive/desorptive exchange, and the sensitivity of the surface tension to adsorbed surfactant. For example, cohesion between hydrocarbon chains favors strong adsorption. Cohesion also slows the rate of desorption from interfaces, and decreases the sensitivity of the surface tension to adsorbed surfactant. Strong cohesive interactions result in first order surface phase changes with a plateau in the surface tension vs surface concentration. Within this surface concentration range, the surface tension is decoupled from surface concentration gradients. We are engaged in the study of the role of surfactant physical chemistry in determining the Marangoni stresses on a drop in an extensional flow in a numerical and experimental program. Using surfactants whose dynamics and equilibrium behavior have been characterized in our laboratory, drop deformation will be studied in ground-based experiment. In an accompanying numerical study, predictive drop deformations will be determined based on the isotherm and equation of state determined in our laboratory. This work will improve our abilities to predict and control all fluid particle flows.

Stebe, Kathleen J.↗
NASA NTRS1983

Data flow methods for dynamic system simulation - A CSSL-IV microcomputer network interface

A major problem in employing networks of microcomputers for the real-time simulation of complex systems is to allocate computational tasks to the various microcomputers in such a way that idle time and time lost in interprocess communication is minimized. The research reported in this paper is directed to the development of a software interface between a higher-level simulation language and a network of microcomputers. A CSSL-IV source program is translated to a data flow graph. This graph is then analyzed automatically so as to allocate computing tasks to the various processors.

Makoui, A.↗
NASA NTRS1994

Program Computes Performances Of Scramjets

SRGULL, a scramjet-cycle-analysis computer code, engineer's software tool capable of nose-to-tail simulation of hydrogen-fueled, scramjet engine integrated with air-frame. Simulated flow that of real gas with equilibrium thermodynamic properties. Program facilities initial estimates of performance of scramjet cycle by linking code for two-dimensional forebody, inlet, and nozzle with code for one-dimensional combustor. Five computer codes (SCRAM, SEAGUL, INLET, Program HUD, and GASH) integrated in program to provide capability for analysis of changing flow conditions. Written in FORTRAN 77.

Walton, J. T.↗
NASA NTRS1992

Large eddy simulations and direct numerical simulations of high speed turbulent reacting flows

The basic objective of this research is to extend the capabilities of Large Eddy Simulations (LES) and Direct Numerical Simulations (DNS) for the computational analyses of high speed reacting flows. In the efforts related to LES, we were primarily involved with assessing the performance of the various modern methods based on the Probability Density Function (PDF) methods for providing closures for treating the subgrid fluctuation correlations of scalar quantities in reacting turbulent flows. In the work on DNS, we concentrated on understanding some of the relevant physics of compressible reacting flows by means of statistical analysis of the data generated by DNS of such flows. In the research conducted in the second year of this program, our efforts focused on the modeling of homogeneous compressible turbulent flows by PDF methods, and on DNS of non-equilibrium reacting high speed mixing layers. Some preliminary work is also in progress on PDF modeling of shear flows, and also on LES of such flows.

Givi, P.↗
NASA NTRS1976

Computer program for design analysis of radial-inflow turbines

A computer program written in FORTRAN that may be used for the design analysis of radial-inflow turbines was documented. The following information is included: loss model (estimation of losses), the analysis equations, a description of the input and output data, the FORTRAN program listing and list of variables, and sample cases. The input design requirements include the power, mass flow rate, inlet temperature and pressure, and rotational speed. The program output data includes various diameters, efficiencies, temperatures, pressures, velocities, and flow angles for the appropriate calculation stations. The design variables include the stator-exit angle, rotor radius ratios, and rotor-exit tangential velocity distribution. The losses are determined by an internal loss model.

Glassman, A. J.↗
NASA NTRS1988

An overview of rotorcraft propulsion research at Lewis Research Center

Rotorcraft propulsion research at Lewis Research Center is discussed, stressing programs in four areas of component research: compressors, combustors, turbines and transmissions, and three developmental programs: the Small Turboshaft Engine Research (STER) Project, the Advanced Rotorcraft Transmission (ART) program, and the Compound Cycle Engine (CCE) program. The component research emphasizes special problems of turboshaft engines in the 5 lb/sec to 30 lb/sec range. The objectives of the STER program are to evaluate the application of advanced concepts to small turboshaft engine systems and to investigate system related phenomena, such as distortion effects and secondary flow phenomena. The goals of the ART program are to reduce transmission weight by 25 percent, noise generation by 10 dB and mean time between removal to 5,000 hrs. The CCE program is working to combine the airflow capacity and light-weight features of a gas turbine with the more efficient, but heavier diesel turbine.

Bill, Robert C.↗
NASA NTRS2006

Seals/Secondary Fluid Flows Workshop 1997; Volume I

The 1997 Conference provided discussions and data on (a) program overviews, (b) developments in seals and secondary air management systems, (c) interactive seals flows with secondary air or fluid flows and powerstream flows, (d) views of engine externals and limitations, (e) high speed engine research sealing needs and demands, and (f) a short course on engine design development margins. Sealing concepts discussed include, mechanical rim and cavity seals, leaf, finger, air/oil, rope, floating-brush, floating-T-buffer, and brush seals. Engine externals include all components of engine fluid systems, sensors and their support structures that lie within or project through the nacelle. The clean features of the nacelle belie the minefield of challenges and opportunities that lie within. Seals; Secondary air flows; Rotordynamics; Gas turbine; Aircraft; CFD; Testing; Turbomachinery

Hendricks, Robert C.↗
NASA NTRS1973

Flowfield analysis for successive oblique shock wave interactions with a turbulent boundary layer

A computation procedure is described for predicting flow fields which develop when successive interactions between oblique shock waves and a turbulent boundary layer occur. Computations were carried out for axisymmetric internal flows at free stream Mach numbers = 3.82 and 2.82. The effect of boundary layer bleed was considered for the free stream Mach number = 2.82 flow. A control volume analysis is used to predict changes in the flow field across the interactions. Two bleed flow models were considered. A turbulent boundary layer program was used to compute changes in the boundary layer between the interactions. The results given are for flows with two shock wave interactions and for bleed at the second interaction site. In principle the method described may be extended to account for additional interactions. The predicted results are compared with measured results and are shown to be in good agreement when the bleed flow rate is low (on the order of 3 percent of the boundary layer mass flow), or when there is no bleed. As the bleed flow rate is increased, differences between the predicted and measured results become larger. Shortcomings of the bleed flow models at higher bleed flow rates are discussed.

Sun, C. C.↗
NASA NTRS1992

Design for a complete SOHO mission under the ISTP

The Solar and Heliospheric Observatory (SOHO) occupies a crucial slot in the International Solar Terrestrial Physics (ISTP) program, which investigates the energy and material flows in key regions of the geospace. Prior space missions which have brought understanding of the corona to what it is today are reviewed. Similarly, space science programs on the horizon will build on SOHO discoveries and insights. SOHO program structure and cost control methods are sketched; tasks have been transferred off the spacecraft where possible, and capabilities will be delivered just before needed. The team analyses of data will be augmented by a SOHO guest investigator program after launch. Theorists on teams would similarly be joined by participants in a proposed SOHO theory program. The ISTP program is built on a foundation of collaborative science, implying the need for observational campaigns directed from a user friendly operations center.

Wagner, W. J.↗
NASA NTRS1999

Study of the Transition Flow Regime using Monte Carlo Methods

This NASA Cooperative Agreement presents a study of the Transition Flow Regime Using Monte Carlo Methods. The topics included in this final report are: 1) New Direct Simulation Monte Carlo (DSMC) procedures; 2) The DS3W and DS2A Programs; 3) Papers presented; 4) Miscellaneous Applications and Program Modifications; 5) Solution of Transitional Wake Flows at Mach 10; and 6) Turbulence Modeling of Shock-Dominated Fows with a k-Enstrophy Formulation.

Hassan, H. A.↗
NASA NTRS1973

A method for calculating unsteady turbulent boundary layers in two- and three-dimensional flows.

The governing equations for an unsteady turbulent boundary layer on a swept infinite cylinder, composed of a continuity equation, a pair of momentum equations and a pair of rate equations for the shear stress, based on the turbulent kinetic-energy equation, are solved numerically. These rate equations for the shear-stress express a balance between the convection, production, dissipation and diffusion of the turbulent shear stress components. Due to the physical model of turbulence employed, this system of equations is hyperbolic. An explicit, second-order accurate, conditionally stable difference scheme for this system, together with appropriate boundary and initial conditions, is formulated and developed into a computer program. Calculations for oscillating free stream flows with no pressure gradient show significant unsteady effects on the turbulent boundary layer.

Singleton, R. E.↗