Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Photocurrent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Current enhancement of CdTe-based solar cells

We report on the realization of CdTe solar cell photocurrent enhancement using an n-type CdSe heterojunction partner sputtered on commercial SnO 2 /SnO 2 :F coated soda-lime glass substrates. With high-temperature close-space sublimation CdTe deposition followed by CdCl 2 activation, this thin-film stack allows for substantial interdiffusion at the CdSe/CdTe interface facilitating a CdSe x Te 1-x alloy formation. The bowing effect causes a reduced optical bandgap of the alloyed absorber layer and, therefore, leads to current enhancement in the long-wavelength region and a decrease in open-circuit voltage (V OC ). To overcome the V OC loss and maintain a high short-circuit current (J SC ), the CdTe cell configuration has been modified using combined CdS:O/CdSe window layers. The new device structure has demonstrated enhanced collection from both short-and long-wavelength regions as well as a V OC improvement. With an optimized synthesis process, a small-area cell using CdS:O/CdSe window layer showed an efficiency of 15.2% with a V OC of 831 mV, a J SC of 26.3 mA/cm 2 , and a fill factor of 69.5%, measured under an AM1.5 illumination without antireflection coating. Furthermore, the results provide new directions for further improvement of CdTe-based solar cells.

14 SOLAR ENERGY↗

A Framework for Process-to-Module Modeling of a-Si/c-Si (HIT) Heterojunction Solar Cells to Investigate the Cell-to-Module Efficiency Gap

The cell-to-module efficiency gap observed in a-Si/c-Si heterojunction solar cells is a key challenge to the broad adoption of this technology. To systematically address this issue, we describe an end-to-end modeling framework to explore the implications of process and device variations at the module level. First, a process model is developed to connect the a-Si deposition parameters to the material properties. Next, a physics-based device model is presented; the model uses the thermionic emission/diffusion theory to capture the essential features of photocurrent and diode injection current. Using the process and device models, the effects of process conditions on cell performance are explored. Finally, the performance of the module, as a function of device and process parameters, is explored to establish the cell-to-module efficiency gap. As a result, the insights developed through this process-to-module modeling framework will help close the cell-to-module efficiency gap of this commercially promising technology.

14 SOLAR ENERGY↗

Measurements and Modeling of III-V Solar Cells at High Temperatures up to 400 °C

Here in this paper, we study the performance of 2.0 eV Al 0.12 Ga 0.39 In 0.49 P and 1.4 eV GaAs solar cells over a temperature range of 25-400 degrees °C. The temperature-dependent J 01 and J 02 dark currents are extracted by fitting current-voltage measurements to a two-diode model. We find that the intrinsic carrier concentration ni dominates the temperature dependence of the dark currents, open-circuit voltage, and cell efficiency. To study the impact of temperature on the photocurrent and bandgap of the solar cells, we measure the quantum efficiency and illuminated current-voltage characteristics of the devices up to 400 °C. As the temperature is increased, we observe no degradation to the internal quantum efficiency and a decrease in the bandgap. These two factors drive an increase in the short-circuit current density at high temperatures. Finally, we measure the devices at concentrations ranging from ~30 to 1500 suns and observe n = 1 recombination characteristics across the entire temperature range. These findings should be a valuable guide to the design of any system that requires high-temperature solar cell operation.

14 SOLAR ENERGY↗

Comparison of CIGS solar cells made with different structures and fabrication techniques

Cu(In, Ga)Se2 (CIGS)-based solar cells from six fabricators were characterized and compared. The devices had differing substrates, absorber deposition processes, buffer materials, and contact materials. The effective bandgaps of devices varied from 1.05 to 1.22 eV, with the lowest optical bandgaps occurring in those with metal-precursor absorber processes. Devices with Zn(O, S) or thin CdS buffers had quantum efficiencies above 90% down to 400 nm. Most voltages were 250-300 mV below the Shockley-Queisser limit for their bandgap. Electroluminescence intensity tracked well with the respective voltage deficits. Fill factor (FF) was as high as 95% of the maximum for each device's respective current and voltage, with higher FF corresponding to lower diode quality factors (~1.3). An in-depth analysis of FF losses determined that diode quality reflected in the quality factor, voltage-dependent photocurrent, and, to a lesser extent, the parasitic resistances are the limiting factors. As a result, different absorber processes and device structures led to a range of electrical and physical characteristics, yet this investigation showed that multiple fabrication pathways could lead to high-quality and high-efficiency solar cells.

14 SOLAR ENERGY↗

Low-Cd CIGS solar cells made with a hybrid CdS/Zn(O,S) buffer layer

In Cu(In,Ga)Se2 (CIGS) solar cells, CdS and Zn(O,S) buffer layers were compared with a hybrid buffer layer consisting of thin CdS followed Zn(O,S). We explore the physics of this hybrid layer that combines the standard (Cd) approach with the alternative (Zn) approach in the pursuit to unlock further potential for CIGS technology. CdS buffer development has shown optimal interface properties, whereas Zn(O,S) buffer development has shown increased photocurrent. Although a totally Cd-free solar module is more marketable, the retention of a small amount of Cd can be beneficial to achieve optimum junction properties. As long as the amount of Cd is reduced to less than 0.01% by weight, the presence of Cd does not violate the hazardous substance restrictions of the European Union (EU). We estimate the amount of Cd allowed in the EU for CIGS on both glass and stainless steel substrates, and we show that reducing Cd becomes increasingly important as substrate weights decrease. As a result, this hybrid buffer layer had reduced Cd content and a wider space charge region, while achieving equal or better solar cell performance than buffer layers of either CdS or Zn(O,S) alone.

14 SOLAR ENERGY↗

The Critical Role of AlInP Window Design in III–V Rear-Emitter Solar Cells

This article highlights the critical role of window design on short circuit carrier collection in rear-emitter solar cells, as demonstrated through modeling and experiment using metamorphic GaAs y P 1-y . Ultimately, if the window design is not carefully considered, surface depletion caused by Fermi level pinning at the window/air interface can extend into regions of active collection resulting in a large increase in effective window/base interface recombination velocity. This was experimentally shown here to result in a potential AM1.5G photocurrent loss of 8.1 mA/cm 2 , or nearly 50%, based on integrated internal quantum efficiency (IQE). Associated IQE modeling and curve fitting indicate that the effective IRV at the GaAs 0.75 P 0.25 /Al 0.64 In 0.36 P interface is increased by multiple orders of magnitude when the window is not sufficiently thick or doped to fully contain the surface depletion to within the window layer. Calculations of the surface depletion depth as a function of doping and the surface Fermi pinning energy level provides insight into the fundamental limits of window thickness. As a result, this allows the estimation of the Al 0.64 In 0.36 P surface pinning level to be at least 1.25 eV below the conduction band edge, or in the bottom half of the bandgap.

14 SOLAR ENERGY↗

Advanced Photovoltaic Module Characterization: Using Image Transformers for Current–Voltage Curve Prediction From Electroluminescence Images

Individual photovoltaic (PV) module health monitoring can be a daunting task for operation and maintenance of solar farms. Modules can be inspected through luminescence, thermal imaging, and current–voltage (I–V) curve analyzes for identification of damage and power loss. I–V curves provide easily interpretable data to determine module health as they directly provide electrical performance metrics. However, in order to obtain these curves, modules must be disconnected from the array and either removed to a solar simulator or characterized in situ with corrections for module temperature, the incident solar spectrum, and intensity. Luminescence or thermal images of a module are relatively easy to acquire in situ. Electroluminescence (EL) images highlight physical defects in the modules but do not provide easily interpretable features to correlate with electrical performance. This work presents a SWin transformer network to predict I–V curves for PV modules from their corresponding EL images. The predicted I–V curves allow the accurate prediction of the maximum power point (MPP), short-circuit current I sc , and open-circuit voltage V oc with a mean error less of than 1%. Comparing single diode model (SDM) parameters extracted from the predicted curves to those extracted from the true curves, the series resistance R s demonstrates a mean error of 5.19%, and the photocurrent I a mean error of 0.197%. The shunt resistance R sh and dark current Io parameters are predicted with larger errors because of their sensitivity to small changes in the I–V curve.

Byford, Brandon K. [New Mexico State Univ., Las Cr↗

Outdoor Performance of a Thin-Film Gallium-Arsenide Photovoltaic Module

We deployed a 855 cm2 thin-film, single-junction gallium arsenide (GaAs) photovoltaic (PV) module outdoors. Due to its fundamentally different cell technology compared to silicon (Si), the module responds differently to outdoor conditions. On average during the test, the GaAs module produced more power when its temperature was higher. We show that its maximum-power temperature coefficient, while actually negative, is several times smaller in magnitude than that of a Si module used for comparison. The positive correlation of power with temperature in GaAs is due to temperature-correlated changes in the incident spectrum. We show that a simple correction based on precipitable water vapor (PWV) brings the photocurrent temperature coefficient into agreement with that measured by other methods and predicted by theory. The low operating temperature and small temperature coefficient of GaAs give it an energy production advantage in warm weather.

14 SOLAR ENERGY↗

Resetting the Defect Chemistry in CdTe

CdTe cell efficiencies have increased from 17% to 21% in the past three years and now rival polycrystalline Si [1]. Research is now targeting 25% to displace Si, attain costs less than 40 cents/W, and reach grid parity. Recent efficiency gains have come largely from greater photocurrent. There is still headroom to lower costs and improve performance by increasing open-circuit voltage (Voc) and fill factor. Record-efficiency CdTe cells have been limited to Voc <; 880 mV, whereas GaAs can attain Voc of 1.10 V with a slightly smaller bandgap [2,3]. To overcome this barrier, we seek to understand and increase lifetime and carrier concentration in CdTe. In polycrystalline structures, lifetime can be limited by interface and grain-boundary recombination, and attaining high carrier concentration is complicated by morphology.

14 SOLAR ENERGY↗

Interfacial Characterization of Positive Bias Voltage Degradation in PV Modules

Degradation from high system voltage is a prevailing failure mode in fielded photovoltaic modules, and the degradation mechanism is inherently dependent on the bias polarity. Here we report the effects of positive bias. Modules under positive bias demonstrated a significant photocurrent loss caused by two routes. First, delamination and discoloration of the silicon nitride layer, leading to optical loss determined by reflectance measurements. Second, chemical discoloration of the cell gridlines and encapsulant (EVA), which is linked to an electrochemical reaction at the silver electrodes. Chemical compositional analysis using X-ray photoemission spectroscopy demonstrated that the discoloration is attributed to Ag 2 S and/or Ag 2 O. Evidence of Ag ion migration from the cell grid into the encapsulant is observed after shallow depth profiling on the EVA surface. However, Ag was not detected at the EVA/glass interface, inferring limited Ag ion transport through the EVA. The source of sulfur is believed to be ambient air, which diffused into the module through the breathable backsheet.

characterization↗

UV-Induced Degradation of High-Efficiency Solar Cells with Different Architectures

The ultraviolet-induced degradation (UVID) of solar panels is associated with the deterioration of cell performance and reduced reliability of packaging materials. Here we examine the UV stability of different architectures of high-efficiency solar cells without any encapsulation. Identical UV exposure tests were performed at two different labs using UVA-340 fluorescent lamps under different electrical bias configurations (open- or short-circuit) and irradiated cell surfaces (for bifacial technologies). Cell technologies, including heterojunction (HJ), interdigitated back-contact cells (IBC), passivated emitter rear contact (PERC), passivated emitter rear totally-diffused (PERT), are found to be more susceptible to UVID, leading to significant Isc loss (up to 4%) and P max loss (up to 15%) as compared to the conventional back surface field (Al-BSF) cells after exposure to UV irradiation of 8.92 MJ-m -2 -nm -1 at 340 nm. Additionally, the bifacial cells when irradiated from the backside exhibited greater photocurrent loss compared to the front side exposure, indicating potential sensitivity of rear surface passivation to UV radiation.

crystalline silicon↗

Evaluation of Fe-βGa 2 O 3 for Photoconductive Semiconductor Switching

We present iron-doped beta gallium oxide (Fe- β Ga2O3) as a candidate for photoconductive semiconductor switches (PCSSs) with sub-bandgap light. From a commercially available Fe- β Ga2O3 wafer, we first did material characterization. This included measurements of absorption coefficient and dopant composition, carrier activation energy up to 200 °C, break down field of planar electrodes (limited from material passivation), and free carrier recombination lifetime, and thermal effects up to 203 °C on photocurrent with a 447 nm light emitting diode (LED) source. Here, we then demonstrated pulsed operation of a Fe- β Ga2O3 PCSS under different sub-bandgap wavelengths (355, 532, and 1064 nm) and sub-ns pulses. Fe- β Ga2O3 is a candidate for high temperature PCSS with 355 nm responsivity of 7×10 -7 A-cm/W-kV at room temperature and up to 5.5×10 -4 A-cm/W-kV at 200 °C. From these investigations, we discuss a simple trap model to describe the illumination process of the PCSS. Fe- β Ga2O3 has a high breakdown field and has moderate responsivity characteristics, but the dark current at high temperature leads to low photo-to-dark current ratio (PDCR). Regardless, we verify its potential as a PCSS material for harsh environment applications.

42 ENGINEERING↗

Bistable Optical Semiconductor Switching Based on C-Doped GaN

Highly resistive gallium nitride (GaN) is an essential material for power optoelectronic applications. While carbon doping is widely used to achieve semi-insulating properties in GaN, the persistent photoconductivity (PPC) arising from deep-level defect traps remains a major obstacle for high-speed power switching. This study demonstrates a novel approach: leveraging the ultrahigh photoresponsivity of GaN:C (up to 2.1 A ⋅ cm/W ⋅ kV, surpassing alternatives such as GaN:Fe) and employing defect-selective optical control to effectively quench the PPC. By synchronizing a short infrared (1064 nm) quenching pulse with UV (385 nm) excitation in an epitaxially grown GaN:C layer on a heavily doped n-type GaN substrate, we achieve a dramatic reduction in photocurrent fall time by approximately 293× (from 470 to 1.6 μ s), increasing modulation bandwidth from 745 Hz to nearly 218 kHz. Here, this advancement not only establishes a new pathway for controlling PPC in GaN:C but also enables the practical integration of GaN:C in fast power switching devices. Enhanced modulation bandwidth, along with GaN:C excellent photoresponsivity, makes it a promising candidate for optically controlled high-voltage, high-power electronic systems, such as photoconductive semiconductor switches (PCSSs) used in pulsed-power drivers, high-power microwave (HPM) sources, and high-voltage gate drivers for wide bandgap (WBG) power electronics.

Carbon-dopped Gallium nitride (GaN:C)↗

The Effects of Gamma Ray Integrated Dose on a Commercial 65-nm SRAM Device

Here this work shows that the static random access memory (SRAM) error rate for a commercial 65-nm device in a dose rate environment can be highly dependent upon the integrated dose (dose rate × pulse duration). While the typical metric for such testing is dose rate upset (DRU) level in rad(Si)/s, a series of dose rate experiments at Little Mountain Test Facility (LMTF) shows dependence on the integrated dose. The error rate is also found to be dependent on the core voltage, and the preradiation value of the bits. We believe that these effects are explained by a well charge depletion caused by gamma ray photocurrent.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Effect of Gamma Radiation on TaOₓ ECRAM

Electrochemical random access memory (ECRAM) is an emerging three-terminal nonvolatile memory (NVM) with highly controllable channel conductance which is promising for use as an analog memory (or synapse) in analog in-memory computing (IMC) systems. Energy-efficient analog IMC computing is particularly desirable for power-constrained, high-radiation environments such as satellites. However, little is known about the suitability of ECRAM for use in a total ionizing dose (TID) environment. Here, this work investigates the effect of Co-60 gamma radiation on the channel conductance and noise—two properties critical for analog IMC systems—of a TaO x -based ECRAM up to 17.3 Mrad(SiO 2 ) for both low- and high-channel-conductance state devices. A transient increase in conductance is observed in response to radiation which consists of two elements: an immediate increase in conductivity due to photocurrent and a secondary increase in conductivity, which has a slower rise and saturation and can persist for hours after exposure. This secondary, persistent photoconductivity is attributed to charging caused by hole trapping. These transient effects would not likely occur in a space environment due to the low dose rate compared with this experiment. No permanent change is found in the low conductance state (LCS) following exposure and the minor shift in the high conductance change would be less significant than the regular retention decay in this state. A permanent increase in the random telegraph noise is observed, possibly due to increased traps created in the channel. This work demonstrates that TaO x -based ECRAM is suitable for use in spaceborne analog IMC systems that are subject to significant TID.

ECRAM↗

Photo-induced surface functionalization of carbon surfaces: The role of photoelectron ejection

Carbon-based materials are attractive for a wide range of applications, from biomaterials to fuel cells; however, their effective use often requires controlling the surface chemistry to incorporate recognition moieties or reactive centers. The high stability of carbon also makes it a challenging material to functionalize; recently, the use of ultraviolet light (254 nm) to initiate functionalization of carbon surfaces has emerged as a way to obtain carbon/organic interfaces with tailored properties. The authors have investigated the mechanism of covalent grafting of amorphous carbon surfaces with functional organic molecules using the photochemical reaction of terminal alkenes. Measurements comparing the reactivity of different n-alkenes bearing different terminal groups at the terminus opposite the olefin showed pronounced differences in reactivity. They characterized the rate and final coverage of the resulting organic layers using x-ray photoelectron spectroscopy and infrared reflection-absorption spectroscopy. Ultraviolet photoelectron spectroscopy and photocurrent measurements suggested that the reaction involves photoelectron emission from the carbon surface into the liquid phase. Density functional calculations show a strong correlation between the electron affinity of the alkenes and the observed reactivity. The specific terminal group opposite to the olefin was found to play an important role in the stabilization of excess negative charges on the molecule, thus explaining the strong dependence of reactivity on the particular terminal group. These findings suggest that the reaction involves injection of photoelectrons into the alkene acceptor levels, leading to the formation of radical anions in the liquid phase. Finally, the authors demonstrate that the grafting of marginally reactive alkenes can be enhanced by seeding the surface with a small amount of good electron accepting groups. These results provide fundamental new insights into the role of electronic excitations in controlling rates and mechanisms of olefin reactions at surfaces. While demonstrated here for amorphous carbon, these results may also be significant for the UV initiated grafting of olefins on other semiconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characterization of x-ray photocathode in transmission mode for imaging application

The performance of an Al x-ray transmission photocathode was experimentally characterized by measuring the total electron yield from backsurface photocathodes of varying thickness. It was demonstrated that the backsurface electron yield is proportional to the x-ray photocurrent transmitted through the photocathode for thicknesses thicker than the optimum thickness. The optimum photocathode thickness with the highest conversion efficiency was found to be approximately 70 nm at 2.963 keV. An escape depth of the secondary electrons was determined to be approximately 13 nm from the yield-versus-thickness data fitted with a semiempirical equation. Using this parameter, the dependence of the optimum photocathode thickness on the x-ray energy was calculated for the 30-10000 eV range. As one example of imaging applications, different photoemission images in the transmission and reflection modes are also presented.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗