Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase transformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Pressure-induced velocity softening in natural orthopyroxene at mantle temperature

In this study, we have measured the compressional and shear wave velocities of (Mg 1.77 Fe 0.22 Ca 0.01 )Si 2 O 6 natural orthopyroxene up to 13.5 GPa and 873 K using ultrasonic interferometry in conjunction with in situ synchrotron X-ray diffraction and imaging techniques. Previous acoustic experiments on orthoenstatite (OEn) MgSiO 3 indicated that both compressional and shear velocities (V P and V S ) of OEn undergo continuous velocity softening above 9 GPa at room temperature, which has been attributed to the phase transition from OEn to the metastable, high-pressure clinoenstatite HPCEn2. For the first time, our results suggest that pressure-induced velocity softening can occur in natural orthopyroxene at high-temperature conditions relevant to the Earth's cold subduction zones. As a result, estimates of the impedance and velocity contrasts between orthopyroxene (Opx) and high-pressure clinopyroxene (HPCpx) have been calculated, and the possibility of this phase transformation being a plausible candidate for seismic X-discontinuities at depth around 250–350 km is re-evaluated.

36 MATERIALS SCIENCE↗

A residual stress study in similar and dissimilar welds

Residual strain distributions in similar and dissimilar welds were measured using neutron diffraction (ND) method. Then, using three strain components, three-dimensional stress states were calculated. The results were used to determine the effect of the martensitic phase transformation and material properties on residual stress (RS) distribution. It was observed that smaller longitudinal RS was induced in the low carbon steel side of dissimilar weld when compared to its similar weld. Also, it was found that the transverse RS near and within the weld zone (WZ) in dissimilar weld exhibited a distinctive trend, with tensile mode reaching the yield strength of the base metal (BM). In order to characterize the WZ in dissimilar weld, we deployed optical microscopy, hardness, and energy dispersive X-ray spectroscopy (EDAX). This study not only provides further insight into the RS state in similar and dissimilar welds; it also delivers important consequences of phase transformation in the latter case.

36 MATERIALS SCIENCE↗

Dopant Distribution in Co-Free High-Energy Layered Cathode Materials

The practical implementation of Co-free, LiNiO 2 -derived cathodes has been prohibited by their poor cycle life and thermal stability, concluded from the structural instability, phase transformations, reactive surfaces, and chemomechanical breakdown. With the hierarchical distribution of Mg/Ti dual dopants in LiNiO 2 , we report a Co-free layered oxide that exhibits enhanced bulk and surface stability. Ti shows a gradient distribution and is enriched at the surface, whereas Mg distributes homogeneously throughout the primary particles. The resulting Mg/Ti codoped LiNiO 2 delivers a material-level specific energy of ~780 W h/kg at C/10 with 96% retention after 50 cycles. The specific energy reaches ~680 W h/kg at 1C with 77% retention after 300 cycles. Furthermore, the Mg/Ti dual dopants improve the rate capability, thermal stability, and self-discharge resistance of LiNiO 2 . Our synchrotron X-ray, electron, and electrochemical diagnostics reveal that the Mg/Ti dual dopants mitigate phase transformations, reduce nickel dissolution, and stabilize the cathode–electrolyte interface, thus leading to the favorable battery performance in lithium metal and graphite cells. The current study suggests that engineering the dopant distribution in cathodes may provide an effective path toward lower cost, safer, and higher energy density Co-free lithium batteries.

25 ENERGY STORAGE↗

Probing enhanced lithium-ion transport kinetics in 2D holey nanoarchitectured electrodes

Nanostructuring has been proved effective towards improving many energy storage and conversion devices, and is feasible for a wide range of materials. In particular, secondary nanoarchitectured materials exhibit collective advantages compared with nano-sized primary building blocks. Despite the manifold efforts in designed nanoarchitectures and synthetic routes, the underlying ion diffusion kinetics and phase transformation behaviours within nanoarchitectures still remain less explored. Herein, we probed enhanced lithium-ion transport behaviours using 2D holey zinc ferrite (ZFO) nanosheets as a model material, to demonstrate how self-assembled 2D holey nanoarchitectured electrodes can feature efficient ion diffusion channels, robust yet continuous electron transfer framework, and enlarged surface area, contributing to the superior performance over the ZFO nanoparticles without secondary structures. By revealing kinetic parameters through combined spectroscopic measurements and electrochemical techniques, our study manifests increased lithium-ion diffusion coefficients, higher capacitive charge storage contribution and reduced charge transfer impedance in holey nanosheets compared to randomly aggregated nanoparticles. Furthermore, our results promote deeper understanding of significantly enhanced electrochemical energy storage properties of these 2D holey nanoarchitectured electrodes resulted from more uniform and complete phase transformation and better active material utilization.

25 ENERGY STORAGE↗

Structural Changes Induced by Low-Flux Ion Irradiation in a Ni{sub 4}Mo Alloy

Irradiation induced random displacements of atoms and replacement collision sequences are possible mechanisms for phase transformations as well as other physical properties changes as grain size variation and hardness increase or decrease. In this study Ni{sub 4}Mo alloy samples were subject to low-flux bombardment by ion beams. This alloy has similar structure to the Hastelloy-C used in industry and to U{sub 3}Si that is used as nuclear fuel. Sample regions were irradiated while the energy density of the bombarding beams was carefully controlled and the non-irradiated regions were kept close to room temperature. This way the irradiation induced temperature increase was highly localized creating ''quench-like'' conditions. After the irradiation, the samples were annealed at low temperature. Due to irradiation conditions there was a high density of nucleation sites favoring the formation of finer grain structures as well as localized phase transformations. The results showed that with the appropriate fluence and post-irradiation treatment, a coarse grained specimen can be forced to re-crystallize with a smaller grain size and manifest a specific change in hardening values due mainly to an order-disorder transformation [1,2].

36 MATERIALS SCIENCE↗

Modeling and Characterization of the Magnetocaloric Effect in Ni2MnGa Materials

Magnetic shape memory alloys have great promise as magneto-caloric effect refrigerant materials due to their combined magnetic and structural transitions. Computational and experimental research is reported on the Ni2MnGa material system. The magnetic states of this system are explored using the Wang-Landau statistical approach in conjunction with the Locally Self-consistent Multiple-Scattering method. The effects of alloying agents on the transition temperatures of the Ni2MnGa alloy are investigated using differential scanning calorimetry and superconducting quantum interference device. Experiments are performed at the Spallation Neutron Source at Oak Ridge National Laboratory to observe the structural and magnetic phase transformations.

magneto caloric↗

Microstructural evolution of fusion zone in laser beam welds of pure titanium

Microstructural evolution of fusion zone in laser beam welds of pure titanium was studied by means of electron backscattering diffraction. The microstructural evolution is strongly affected by the {beta} {yields} {alpha} transformation mechanism dependent on the cooling rate during phase transformation. The long-range diffusional transformation mainly occurs in the fusion zone at the low cooling rate, and the massive transformation dominantly takes place at the high cooling rate. For this reason, the grain morphologies probably change from the granular-like to columnar-like grains with the cooling rate increasing. - Highlights: Black-Right-Pointing-Pointer Microstructures of fusion zone in laser beam welds of pure titanium are studied. Black-Right-Pointing-Pointer Increasing cooling rate changes grain morphology from granular to columnar one. Black-Right-Pointing-Pointer Final microstructures depend on the {beta}{yields}{alpha} transformation mechanisms.

36 MATERIALS SCIENCE↗

Synthesis, structural characterization and Mössbauer study of LnV{sub 0.5}Fe{sub 0.5}O{sub 3} perovskites (Ln = Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho and Er)

Graphical abstract: Mössbauer spectra taken at 200 K for the Y(V{sub 0.5}Fe{sub 0.5})O{sub 3} orthoferrivanadate synthesized by arc-melting. Highlights: ► LnFe{sub 0.5}V{sub 0.5}O{sub 3} were synthesized by the first time for most of the rare-earth elements. ► These orthoferrivanadates crystallize metastably with the perovskite structure. ► Iron and vanadium are trivalent stabilized in these solid solutions. ► The Mössbauer quadrupolar splitting is correlated with the tolerance factor. ► Below 100 K, these perovskites undergo a crystallographic phase transformation. -- Abstract: Perovskites LnV{sub 0.5}Fe{sub 0.5}O{sub 3} (Ln = Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho and Er) were synthesized by rapid solidification from arc-melted samples and characterized by the study of their crystal structure and hyperfine properties. These metastable solid solutions crystallized in the Pbnm symmetry, with the iron and vanadium cations randomly distributed in the transition metal octahedral sites. Depending on the lanthanide present at the A site of the perovskite, iron is present with two valences (i.e., Fe{sup 3+} and Fe{sup 2+}). The volume of the unit cell for these perovskites increases linearly with the lanthanide ionic radius, as the perovskite approaches its ideal structure. At room temperature, the quadrupolar splitting of the trivalent paramagnetic Mössbauer component works as an indirect measurement for the Goldshmidt tolerance factor. Close to or below 100 K, these perovskites undergo a crystallographic phase transformation, probably due to orbital ordering of the V{sup 3+} cations, originating two different magnetic iron sites.

36 MATERIALS SCIENCE↗

FCRD Advanced Reactor (Transmutation) Fuels Handbook

Transmutation of minor actinides such as Np, Am, and Cm in spent nuclear fuel is of international interest because of its potential for reducing the long-term health and safety hazards caused by the radioactivity of the spent fuel. One important approach to transmutation (currently being pursued by the DOE Fuel Cycle Research & Development Advanced Fuels Campaign) involves incorporating the minor actinides into U-Pu-Zr alloys, which can be used as fuel in fast reactors. U-Pu-Zr alloys are well suited for electrolytic refining, which leads to incorporation rare-earth fission products such as La, Ce, Pr, and Nd. It is, therefore, important to understand not only the properties of U-Pu-Zr alloys but also those of U-Pu-Zr alloys with concentrations of minor actinides (Np, Am) and rare-earth elements (La, Ce, Pr, and Nd) similar to those in reprocessed fuel. In addition to requiring extensive safety precautions, alloys containing U, Pu, and minor actinides (Np and Am) are difficult to study for numerous reasons, including their complex phase transformations, characteristically sluggish phasetransformation kinetics, tendency to produce experimental results that vary depending on the histories of individual samples, rapid oxidation, and sensitivity to contaminants such as oxygen in concentrations below a hundred parts per million. Although less toxic, rare-earth elements such as La, Ce, Pr, and Nd are also difficult to study for similar reasons. Many of the experimental measurements were made before 1980, and the level of documentation for experimental methods and results varies widely. It is, therefore, not surprising that little is known with certainty about U-Pu-Zr alloys, particularly those that also contain minor actinides and rare-earth elements. General acceptance of results commonly indicates that there is only a single measurement for a particular property. This handbook summarizes currently available information about U, Pu, Zr, Np, Am, La, Ce, Pr, and Nd and alloys of two or three of these elements. It contains information about phase diagrams and related information (including phases and phase transformations); heat capacity, entropy, and enthalpy; thermal expansion; and thermal conductivity and diffusivity. In addition to presenting information about materials properties, the handbook attempts to provide information about how well the property is known and how much variation exists between measurements. Although it includes some results from models, its primary focus is experimental data. The Handbook is organized in two sections: one with information about the U-Pu-Zr ternary and one with information about other elements and binary and vi ternary alloys in the U-Np-Pu-Am-La-Ce-Pr-Nd-Zr system. Within each section, information about elements is presented first, followed by information about binary alloys, then information about ternary alloys. The order in which the elements in each alloy are mentioned follows the order in the first sentence of this paragraph. Much of the information on the U-Pu-Zr system repeats information from the FCRD Transmutation Fuels Handbook 2015. Most of the other data has been published elsewhere (although scattered throughout numerous references, some quite obscure); however, some data from Idaho National Laboratory is presented here for the first time. As the FCRD programmatic mission evolves, future editions of this handbook will begin to include other advanced reactor fuel designs and compositions. Hence, the title of the handbook will transition to the Advanced Reactor Fuels Handbook.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Atomic-scale Mechanisms of Enhanced Electrochemical Properties of Mo-doped Co-free Layered Oxide Cathodes for Lithium-Ion Batteries

Cobalt-free layered oxides with high specific capacity and low cost have emerged as promising candidates for next-generation cathodes for lithium-ion batteries. However, implementation of these materials has been hindered by their low rate capability, structural instability, and rapid capacity decay during cycling. Recent studies have shown that introducing cation dopants into layered oxides can strongly improve their electrochemical properties, but the underlying mechanisms remain elusive due to a lack of information at the atomic scale. In this work, we use a combination of atomic-resolution scanning transmission electron microscopy and first principle calculations to reveal the microscopic origin of enhanced electrochemical properties in LiNi0.5Mn0.5O2 doped with ~1 at % Mo. These results indicate that the Mo dopant hinders Li+/Ni2+ cation mixing and suppresses detrimental phase transformations near the particle surface and at grain boundaries, which enhances the cathode’s reversible capacity and cycling stability. Overall, This work provides important insights on how cation doping affects the structure and electrochemical properties of layered oxide cathodes.

Li, Linze↗

Segmentation of tomography datasets using 3D convolutional neural networks

Dendritic microstructures are ubiquitous in nature and are the primary solidification morphologies in metallic materials. Techniques such as X-ray computed tomography (XCT) have provided new insights into dendritic phase transformation phenomena. However, manual identification of dendritic morphologies in microscopy data can be both labor intensive and potentially ambiguous. The analysis of 3D datasets is particularly challenging due to their large sizes (terabytes) and the presence of artifacts scattered within the imaged volumes. Here, in this study, we trained 3D convolutional neural networks (CNNs) to segment 3D datasets. Three CNN architectures were investigated, including a new version of FCDenseNet which we extended to 3D. We show that using hyperparameter optimization (HPO) and fine-tuning techniques, both 2D and 3D CNN architectures outperform the previous state of the art. The 3D U-Net architecture trained in this study produced the best segmentations according to quantitative metrics (intersection-over-union of 95.56% and a boundary displacement error of 0.58 pixels), while 3D FCDense produced the smoothest boundaries and best segmentations according to visual inspection. The trained 3D CNNs are able to segment entire 852 × 852 × 250 voxel 3D volumes in only ~60 s, thus hastening the progress towards a deeper understanding of phase transformation phenomena such as dendritic solidification.

36 MATERIALS SCIENCE↗

Suppressed oxygen extraction and degradation of LiNixMnyCozO2 cathodes at high charge cut-off voltages

The capacity degradation mechanism in lithium nickel-manganese-cobalt oxide (NMC) cathodes (LiNi1/3Mn1/3Co1/3O2 (NMC333) and LiNi0.4Mn0.4Co0.2O2 (NMC442)) during high-voltage (cut-off of 4.8 V) operation has been investigated. In contrast to NMC442, NMC333 exhibits rapid structural changes including severe micro-crack formation and phase transformation from a layered to a disordered rock-salt structure, as well as interfacial degradation during high-voltage cycling, leading to a rapid increase of the electrode resistance and fast capacity decline. The fundamental reason behind the poor structural and interfacial stability of NMC333 was found to be correlated to its high Co content and the significant overlap between the Co3+/4+ t(2g) and O2- 2p bands, resulting in oxygen removal and consequent structural changes at high voltages. In addition, oxidation of the electrolyte solvents by the extracted oxygen species generates acidic species, which then attack the electrode surface and form highly resistive LiF. These findings highlight that both the structural and interfacial stability should be taken into account when tailoring cathode materials for high voltage battery systems

Environmental Molecular Sciences Laboratory↗

Atomic to Nanoscale Investigation of Functionalities of an Al2O3 Coating Layer on a Cathode for Enhanced Battery Performance

Surface coating has been identified as an effective approach for enhancing the capacity retention of layered structure cathode. However, the underlying operating mechanism of such a thin coating layer, in terms of surface chemical functionality and capacity retention, remains unclear. In this work, we use aberration-corrected scanning transmission electron microscopy and high-efficiency spectroscopy to probe the delicate functioning mechanism of an Al2O3 coating layer on a Li1.2Ni0.2Mn0.6O2 cathode. We discovered that in terms of surface chemical function, the Al2O3 coating suppresses the side reaction between the cathode and the electrolyte during battery cycling. At the same time, the Al2O3 coating layer also eliminates the chemical reduction of Mn from the cathode particle surface, therefore preventing the dissolution of the reduced Mn into the electrolyte. In terms of structural stability, we found that the Al2O3 coating layer can mitigate the layer to spinel phase transformation, which otherwise will be initiated from the particle surface and propagate toward the interior of the particle with the progression of battery cycling. The atomic to nanoscale effects of the coating layer observed here provide insight into the optimized design of a coating layer on a cathode to enhance the battery properties.

Yan, Pengfei↗

Radiation-Enhanced Anion Transport in Hematite

The influence of radiation-induced (1 MeV energy H+ to ~0.1 dpa at 450°C), non-equilibrium point defect populations on mass transport is studied with an integrated campaign of experimental and theoretical methods. Using epitaxial thin films of hematite with embedded 18O tracer layers and nanoscale atom probe tomography measurements, it is shown that anion self-diffusion is enhanced by at least 2 orders of magnitude under irradiation compared to thermal diffusion alone. Complementary scanning transmission electron microscopy of vacuum annealed specimens, reveals associated microstructural changes in the oxide films, including local phase transformation to Fe3O4 and the development of nanoscale voids from vacancy coalescence. Point defect formation and migration energies were computed from density functional theory and applied within the context of chemical rate theory to analyze contributions from both interstitial and vacancy mechanisms to self-diffusion in thermal and irradiation conditions. Comparisons are made between calculated, literature and newly measured self-diffusion values, revealing good agreement on the magnitude of radiation-enhanced anion diffusion. Further, the model suggests a transition from vacancy to interstitialcy mechanisms at low temperatures and high oxygen activity, consistent with the varied activation energies reported from prior studies.

iron oxides, isotopic tracers, atom probe tomograp↗

Precipitation-site competition in duplex stainless steels: Cu clusters vs spinodal decomposition interfaces as nucleation sites during thermal aging

Competing microstructural evolution mechanisms can exist simultaneously when duplex stainless steels are operating for several decades in a high temperature service environment. Such competition between different microstructural evolution pathways can be difficult to ascertain using simple model alloy systems necessitating detailed structural and compositional analysis of phase transformation mechanisms in complex alloys Thus, in this study duplex stainless steels with complex but well understood chemistries were used to investigate the relative importance of different heterogeneous nucleation sites – specifically spinodal decomposition and Cu clustering – on precipitation of Ni-Si-Mn particles during long term thermal aging. Precipitation of Ni-Si-Mn particles in duplex stainless steels and ferritic steels during thermal aging and irradiation is known to have profound effect on mechanical properties. Using duplex stainless steels with custom modified compositions along with atom probe tomography characterization and first-passage kinetic Monte Carlo (FPKMC) simulations it is revealed that while the interface between Cr and Fe formed during spinodal decomposition can be a pathway for diffusion of Ni, Si, Mn, and Cu, it is not a site that encourages precipitation of Ni-Si-Mn rich particles. Instead, the presence of a higher concentration of Cu in these steels leads to formation of small Cu clusters with high energy interfaces that act as nucleation sites for Ni-Si-Mn particles because of its strong interaction particularly with Ni increasing the chemical driving force for precipitation. These results will help inform predictive models for the use of duplex stainless steels and other precipitation-hardened alloys for extended operation at high temperatures.

Duplex stainless steel, Thermal aging, Precipitati↗

Chemo-Mechanical Instabilities in Lithium Cobalt Oxide at Higher State-Of-Charge in Li-Ion Batteries

Transition metal oxide cathodes are widely used in commercial Li-ion batteries. However, their practical charge capacity is limited due to severe chemo-mechanical instabilities at higher charge voltage, and state-of-charge condition. Here, in situ stress and strain measurements were synchronized to probe mechanical deformations in the lithium cobalt oxide (LCO) cathode via a multi-beam stress sensor and digital image correlation, respectively. In situ mechanical measurements revealed how Li removal from the electrode structure induces deformations on the LCO composite cathodes during cycling. The structure and morphology of the LCO cathodes were further investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies. Two distinct electrochemical and mechanical behaviors were identified when the LCO was charged up to 4.65 V. The LCO undergoes a compressive stress generation when charged up to 4.2 V and surface fractures on the LCO particles were detected by SEM. LCO cathode experienced significantly large contractions (negative strains) when charged up to 4.65 V, where intergranular crack formation and phase transformation were detected on the LCO particles via SEM and XRD, respectively. Overall, the study bridges complicated structural deformations with in situ analysis of mechanical degradations in LCO cathodes charged at higher voltages. The correlation is vital to understanding instability mechanisms in transition metal oxides at high voltages for alkali metal ion batteries.

higher state-of-charge↗

A high-voltage rechargeable magnesium-sodium hybrid battery

Growing global demand of safe and low-cost energy storage technology triggers strong interests in novel battery concepts beyond state-of-art Li-ion batteries. Here we report a high-voltage rechargeable Mg–Na hybrid battery featuring dendrite-free deposition of Mg anode and Na-intercalation cathode as a low-cost and safe alternative to Li-ion batteries for large-scale energy storage. A prototype device using a Na3V2(PO4)3 cathode, a Mg anode, and a Mg–Na dual salt electrolyte exhibits the highest voltage (2.60 V vs. Mg) and best rate performance (86% capacity retention at 10C rate) among reported hybrid batteries. Synchrotron radiation-based X-ray absorption near edge structure (XANES), atomic-pair distribution function (PDF), and high-resolution X-ray diffraction (HRXRD) studies reveal the chemical environment and structural change of Na3V2(PO4)3 cathode during the Na ion insertion/deinsertion process. XANES study shows a clear reversible shift of vanadium K-edge and HRXRD and PDF studies reveal a reversible two-phase transformation and V–O bond length change during cycling. The energy density of the hybrid cell could be further improved by developing electrolytes with a higher salt concentration and wider electrochemical window. This work represents a significant step forward for practical safe and low-cost hybrid batteries.

Li, Yifei↗

New Synthesis Strategies to Improve Co-Free LiNi0.5Mn0.5O2 Cathodes: Early Transition Metal d0 Dopants and Manganese Pyrophosphate Coating

In this work, we report solution-based doping and coating strategies to improve the electrochemical performance of the Co-free layered oxide cathode LiNi0.5Mn0.5O2 (LNMO). Small amounts of d0 dopants (e.g., Mo6+and Ti4+, 0.5-1 at. %) increase the cathode’s specific capacity, cycling stability, and rate capability. More specifically, a Mo-doped cathode with the nominal composition LiNi0.495Mn0.495Mo0.01O2 achieves a high reversible capacity of 180 mAh/g at 20 mA/g with good retention at higher rates (e.g., 120 mAh/g at 100 mA/g). Effects of 1 at.% Mo dopant on the cathode structure were studied using a suite of characterization tools including X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). These measurements demonstrate that Mo6+ reduces Li+/Ni2+cation mixing and mitigates undesirable phase transformations near the cathode surface during cycling. This work also reports the use of an inorganic Mn2P2O7 coating which enhances cycling stability, presumably through formation of a stable cathode electrolyte interphase (CEI) layer. Overall, the synthesis approaches reported herein are quite general and can potentially be expanded to other high voltage LIB cathodes.

Co-free cathodes, d0 cation, pyrophosphate coating↗