Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA ENGINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

US/Russian Cooperative Program in Science and Technology

Developing a sophisticated theory to understand the electronic structure of 5f-metals is a great challenge to solid-state physics. Complicated electronic structures of 5f metals make their properties strongly sensitive to small energy changes produced by the addition of a small amount of alloy, impurities, or crystal structure defects caused by irradiation. A theoretical material science technique applicable to investigate these effects is atomistic simulation using Classical Molecular Dynamics (CMD). In contrast to ab initio techniques, CMD may include several million particles, so that there is a possibility of direct simulation of very low concentration impurities and defects (as well as phenomena such as plasticity and polymorphous transitions) under given conditions.

36 MATERIALS SCIENCE↗

Fast response, optical radiance measurements of low intensity impurity emission in WEST plasmas with staggered wavelength filters

Fast response acquisition of atomic line emission through the use of a filterscope has been implemented on the WEST tokamak at multiple poloidal locations. Filterscopes consist of a fiber-optic-based transmission from the tokamak to specifically engineered optical bandpasses and photomultiplier tubes (PMT) that collect the emission intensity to measure a radiance, L [W/cm2/str], over the specified bandpass. This diagnostic records plasma-wall interaction (PWI) properties (e.g. impurity emission and recycling of main fuel ions) up to a max acquisition rate of 100 kHz. These PMT radiometric measurements are calibrated into a line-normalized radiance, LN [photons/sec/cm2/str], similar to traditional spectrometers, which can later be converted to a particle flux. Low intensity emission peaks are difficult to quantify due to often comparable continuum levels, thus a secondary filter shifted to a judiciously-selected, line-free region (~1 nm away) allows for background subtraction. The system currently installed on WEST targets tungsten (W) gross sputtering specifically by monitoring, with a filter pair, the spectral region near the neutral W line emission (W I 400.9 nm). The line and background filters of the pair are centered at 400.6 nm and 403.1 nm, respectively. Through a set beam splitters on each sight line, the filter pair are measuring from the same location. The two L signals near W I are then subtracted from each other yielding only the W I LN. W I LN data from a recent WEST experimental campaign is presented and compared with plasma parameters and traditional spectrometer measurements of W I line emission to demonstrate the capabilities of this staggered-filter filterscope method. Specifically, the choice of WEST-specific bandpass curves for the W I LN will be illustrated based on this latter comparison.

Neff, Anton↗

Princeton Plasma Physics Laboratory Annual Site Environmental Report for Calendar Year 2024

This report provides the US Department of Energy (DOE) and the public with information on the level of radioactive and non-radioactive pollutants (if any) that are added to the environment as a result of Princeton Plasma Physics Laboratory’s (PPPL) operations. This report fulfills the annual public reporting requirements of DOE Order 231.1B. The results of PPPL’s 2024 environmental surveillance and monitoring program are presented and discussed. The report also summarizes environmental initiatives, assessments, and community involvement programs that were undertaken in 2024. PPPL has engaged in fusion energy research since 1951 and at its current locations since 1958. The Laboratory’s mission is to develop the scientific knowledge and advanced engineering to enable fusion to power the US and the world, and to develop the understanding of plasmas from the nano- to the astrophysical scale. PPPL’s primary experiment, the National Spherical Torus Experiment-Upgrade (NSTX-U) is a collaboration among national laboratories, universities, and national and international research institutions and is a major element in the US Fusion Energy Sciences Program. Its design tests the physics principles of spherical torus (ST) plasmas, playing an important role in the development of smaller, more economical fusion reactors. Due to previous operational issues, NSTX-U did not operate in 2024. PPPL is engaged in a project to replace key NSTX-U components and systems to enable the operation of this international magnetic fusion user facility. In 2024, PPPL’s radiological environmental monitoring program measured tritium in the air at onsite sampling stations. Using highly sensitive air monitors, PPPL is capable of detecting small changes in the ambient levels of tritium. The operation of monitors located on D-site is used to demonstrate compliance with the National Emission Standard for Hazardous Air Pollutants (NESHAPs) regulations. Also included in PPPL’s radiological environmental monitoring program, are water monitoring – ground, surface, and waste waters. PPPL’s radiological monitoring program characterized the background levels of tritium in the environment and those data are presented in this report. Ground water monitoring continued under New Jersey Department of Environmental Protection’s (NJDEP) Site Remediation Program regulations. PPPL monitored for nonradiological contaminants, mainly volatile organic compounds (components of common degreasing solvents). In 2024, PPPL complied with permit limits for surface water and sanitary wastewater discharges. PPPL was honored with an award for EPEAT-certified electronics purchasing from the Global Electronics Council on July 25, 2024.

54 ENVIRONMENTAL SCIENCES↗

Models implemented in the methodological approach to design the initial STEP first wall contour

The official Spherical Tokamak for Energy Production mission aims to demonstrate the ability to generate net electricity from fusion with the STEP Prototype Power plant. One of the key technological and engineering challenges in fusion power plants is managing the loads on the first wall within acceptable limits. Therefore, the conceptual design development of the STEP Prototype Power plant needs to be based on load estimates derived using legitimate plasma physics assumptions through dynamic and flexible tools. The current design foresees the STEP main chamber first wall to withstand steady-state heat loads of up to ~1 MW/m 2 , excluding critical regions expected to receive higher heat loads such as the baffle regions approaching the divertors. These critical areas will require ad hoc assessments and will be designed with the presence of limiters. This article focuses on the models and methodology adopted for designing the 2-D poloidal contour of the STEP first wall, based on the anticipated charged particle and radiation heat loads during normal operation. Firstly, the models adopted for calculating the charged particle and radiation heat loads are introduced. The first model is validated through benchmarking against the particle tracing code SMARDDA, while the second model is verified by comparing it with data from the MAST-U experiment. Secondly, the model used to design the 2-D first wall contour according to the heat loads is explained. We acknowledge that this preliminary design stage assumes certain simplifications, notably an axisymmetric geometry, for computational efficiency and clarity in presentation. It is understood that subsequent design phases will address the complexities of real-world engineering, including non-axisymmetric effects, transient plasma scenarios, and the impact of disruptions on the first wall design. Finally, an automatic procedure based on these models is presented for defining the 2-D poloidal contour of the STEP first wall to minimize heat loads, taking into account the need to radiate most of the alpha-particle and auxiliary heating power. Here, by providing an overview of the models, methodology, and an automatic procedure, this paper contributes to the design process of the STEP first wall, addressing the engineering challenges associated with fusion power plant development.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The application of radiochronometry during the 4th collaborative materials exercise of the nuclear forensics international technical working group (ITWG) [Radiochronometry in the CMX-4 exercise]

In a recent international exercise, 10 international nuclear forensics laboratories successfully performed radiochronometry on three low enriched uranium oxide samples, providing 12 analytical results using three different parent-daughter pairs serving as independent chronometers. The vast majority of the results were consistent with one another and consistent with the known processing history of the materials. In general, for these particular samples, mass spectrometry gave more accurate and more precise analytical results than decay counting measurements. Additionally, the concordance of the 235 U– 231 Pa and 234 U– 230 Th chronometers confirmed the validity of the age dating assumptions, increasing confidence in the resulting conclusions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Machine learning-assisted early ignition prediction in a complex flow

Machine learning methods are used to improve the efficiency by which turbulence-resolved simulations predict whether a hydrogen jet in air crossflow will successfully ignite. The flush-mounted jet issues perpendicularly from the wall of a low-speed wind tunnel into a turbulent boundary layer wherein a laser-induced optical breakdown (LIB) hotspot is deposited. A detailed hydrogen chemical mechanism is used to model the radicals and any subsequent chemical reactions. A dielectric-barrier discharge actuator generates body forces and hydrogen radicals near the jet orifice. Here we focus on the success or not of the ignition based on LIB location. A challenge is that definitive determination of this requires long simulations, up to 440 µs after the LIB deposition. This is particularly expensive since multiple simulations are required to find the threshold. To reduce the computational effort, three short-time (91 µs) criteria are proposed, evaluated, and compared: a constructed criterion based on detailed observations of radicals near the stoichiometric surface and two machine learning approaches, each trained on 38 realizations. The constructed criterion provides a low-cost estimate of the ignition boundary that is unambiguous in 45 of the 50 training and test trials, so only 10% of them would need to be simulated longer. The trained neural networks correctly predict outcomes in all cases evaluated, with the more automated procedure—a convolutional neural network (CNN) trained on two-dimensional images—providing the most definitive outcome prediction. From the CNN, a sensitivity analysis is used to determine which kernel features from the two-dimensional input data, as defined by intermediate-layer network weights, are important for identifying ignition.

42 ENGINEERING↗

Modeling deformation and failure in AlSi-polyester abradable sealcoating material using microstructure-based finite element simulation

A plasma-sprayed aluminum-silicon (AlSi)/polyester coating is applied in modern gas turbine engines as an abradable sealcoating to maintain tight clearances between the rotating blades and the static casing. While running the engine, the rotating blades “rub” with the abradable coating, which results in extreme strain rate (up to 10 6 ) dynamics and a high-temperature environment. Due to the difficulty of collecting direct measurements, predictive computational models are important for analyzing the deformation and failure of the abradable material, to help meet the design target of avoiding damage to the blade tip and maintaining high fuel efficiency. In this research, a microstructure-based finite element (FE) computational model was developed to capture the complex mechanical behavior of the AlSi/polyester microstructure. The model is based on a virtual representative-volume-element (RVE) of a metal-polymer microstructure, reconstructed from x-ray computed tomography. It models the plastic deformation of, and damage to, each AlSi and polyester constituents, as well as the failure at their interface. The model was calibrated and validated with uniaxial tension and compression experiments, conducted at two temperatures (298 K and 533 K) at an applied strain rate of 10 3 - 10 4 s -1 . The material exhibited strongly asymmetric tension-compression behavior and a sensitivity to temperature, which was well captured by the model. The model was further applied to investigate changes in mechanical behavior due to variations in constituents’ volume fractions, which provides guidance to the microstructural design of AlSi/polyester abradable materials. The model is expected to facilitate the development of improved abradable materials by bypassing the conventional trial-and-error approach and extensive testing requirements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Steady detonation propagation in thin channels with strong confinement

We examine asymptotically the dynamics of two-dimensional, steady detonation wave propagation and failure for a strongly confined high explosive (HE), in which the width of the explosive is small relative to the reaction zone length. An energy balance equation is derived, which shows how the longitudinal acceleration of subsonic flow behind the detonation shock is influenced both by chemical reaction and by the effects of HE boundary streamline deflection, specifically via the induced rate of change of mass flux through the detonation wave. The latter serves to either counteract or reinforce the acceleration of longitudinal flow, depending on the sign of the gradient of the boundary streamline deflection at the detonation shock. The analysis is valid for general equations of state and chemical reaction rates in the HE. The asymptotically derived form of the energy equation represents an eigenvalue problem for the determination of the steady detonation propagation speed, solved via a shooting method. We explore specific results for ideal and stiffened equations of state, along with a pressure-dependent reaction rate for which changes in the pressure exponent and reaction order are also studied. We consider the influences of both straight and curved HE boundary streamline shapes. The asymptotic analysis reveals significant physical insights into how detonation propagation and failure are affected by strong confinement.

42 ENGINEERING↗

Compact, Inexpensive Micro-Reformer for Distributed GTL Systems (Final Scientific/Technical Report)

This award allowed MIT Plasma Science and Fusion Center, in collaboration with the Departments of Chemical and Mechanical Engineering, to demonstrate the feasibility of using an engine as the reformer for a gas-to-liquids plants. Engine reformation in cylinder has been used in the past for limited production of hydrogen rich gas. However, the performance was limited, and for syngas generation as part of a chemical plant, the output was inadequate. The focus of the ARPA-E seed project was to demonstrate, in oxygen or in air, the production of hydrogen rich gas with good conversion and selectivity. The goal was equivalence ratios ~ 3 in oxygen, or highly enriched air. The accomplishment performance was equivalence ratios ~ 2 with air.

03 NATURAL GAS↗

High temperature self-lubricating coatings for air lubricated foil bearings for the automotive gas turbine engine

coating combinations were developed for compliant surface bearings and journals to be used in an automotive gas turbine engine. The coatings were able to withstand the sliding start/stops during rotor liftoff and touchdown and occasional short time, high speed rubs under representative loading of the engine. Some dozen coating variations of CdO-graphite, Cr2O3 (by sputtering) and CaF2 (plasma sprayed) were identified. The coatings were optimized and they were examined for stoichiometry, metallurgical condition, and adhesion. Sputtered Cr2O3 was most adherent when optimum parameters were used and it was applied on an annealed (soft) substrate. Metallic binders and interlayers were used to improve the ductility and the adherence.

Bhushan, B.↗

Electrodynamic Interactions

It is apparent that the electrodynamic tether offers new potential for unique scientific experiments which should enhance the understanding of space plasma physics and in particular certain classes of solar system plasma phenomena, and that these science studies will also address a number of key engineering concerns which may open up new power and thrust generation technology that could be a significant factor in future space operations.

Stone, N. H.↗

Second Magnetoplasmadynamic Thruster Workshop

The meeting focused on progress made in establishing performance and lifetime expectations of magnetoplasmadynamic (MPD) thrusters as functions of power, propellant, and design; models for the plasma flow and electrode components; viability and transportability of quasi-steady thruster testing; engineering requirements for high power, long life thrusters; and facilities and their requirements for performance and life testing.

Source record↗

JPL nuclear electric propulsion task

The development of lithium magnetoplasmadynamic (MPD) thrusters at JPL is discussed. The following topics are presented in vugraph form: mercury vapor mass flow control; porous tungsten vaporizer and housing; the lithium vaporizer experiment; a dry box for handling solid lithium; MPD thruster electrode modeling; engine lifetime definitions; cathode failure modeling; cathode erosion modeling; cathode thermal modeling; near cathode plasma model regions; cathode work function modeling; anode work function modeling; and radiation-cooled anodes.

Pivirotto, Tom↗

Current status of environmental barrier coatings for Si-Based ceramics

Silicon-based ceramics are the leading candidates for high temperature structural components in next generation gas turbine engines. One key drawback of silicon-based ceramics for such an application is volatilization of the protective silica scale in water vapor and the resulting rapid ceramic recession. Therefore, the realization of Si-based ceramics components in advanced gas turbine engines depends on the development of protection schemes from water vapor attack. Currently, plasma-sprayed external environmental barrier coatings (EBCs) arc the most promising approach. In the late 1980s and early 1990s a wide range of refractory oxide materials were tested as coatings on Si-based ceramics to provide protection from hot corrosion. After the discovery of silica volatilization in water vapor in the early 1990s, the focus of EBC development research has been shifted towards the protection from water vapor attack. Experience learned form the earlier coating developmental effort provided the foundation upon which more complex and advanced EBC coatings have been developed. This paper will discuss the brief history and the current status of EBC development for Si-based ceramics with the main focus on water vapor protection.

Lee, K. N.↗

High velocity pulsed wire-arc spray

Wire arc spraying using repetitively pulsed, high temperature gas jets, usually referred to as plasma jets, and generated by capillary discharges, substantially increases the velocity of atomized and entrained molten droplets. The quality of coatings produced is improved by increasing the velocity with which coating particles impact the coated surface. The effectiveness of wire-arc spraying is improved by replacing the usual atomizing air stream with a rapidly pulsed high velocity plasma jet. Pulsed power provides higher coating particle velocities leading to improved coatings. 50 micron aluminum droplets with velocities of 1500 m/s are produced. Pulsed plasma jet spraying provides the means to coat the insides of pipes, tubes, and engine block cylinders with very high velocity droplet impact.

Witherspoon, F. Douglas↗

Assessments of Hollow Cathode Wear in the Xenon Ion Propulsion System (XIPs(c)) by Numerical Analyses and Wear Tests

The standard approach presently followed by NASA to qualify electric propulsion for the required mission throughput has been based largely on life tests, which can be costly and time consuming. Revised electric propulsion lifequalification approaches are being formulated that combine analytical and/or computational methods with (shorter-duration) wear tests. As a model case, a wear test is being performed at JPL to assess the lifetime of the discharge hollow cathode in the Xenon Ion Propulsion System (XIPS(c)), a 25-cm ion engine developed by L-3 Communications Electron Technologies, Inc. for commercial applications. Wear and plasma data accumulated throughout this life-assessment program are being used to validate the existing 2-D hollow cathode code OrCa2D. We find that the OrCa2D steady-state solution predicts very well the time-averaged plasma data and the keeper voltage after 5500 hrs of operation in high-power mode. When the wave motion that occurs naturally in these devices is accounted for, based on an estimate of the maximum wave amplitude, the molybdenum-keeper erosion profile observed in the XIPS(c) discharge cathode is also reproduced within a factor of two of the observation. When the same model is applied to predict the erosion of a tantalum keeper we find that erosion is reduced by more than two orders of magnitude compared to the molybdenum keeper due the significantly lower sputtering yield of tantalum. A tantalum keeper would therefore allow keeper lifetimes that greatly exceed the present requirements for deep-space robotic missions considered by NASA. Moreover, such large reduction of the erosion renders the largest uncertainties in the models, which are associated with the wave amplitude estimates and the electron transport model, negligible.

plasma simulations↗

Effect of the Thermal Stability and Reactivity of Fullerenes on Ion Engine Propellant Applications

Because vapor phase fullerene molecules collide with high temperature surfaces at both the cathode in DC discharges and at the walls of vapor sources, knowledge of the thermal stability and material compatibility of fullerenes is important for ion thruster applications. Here, we present a study of the high temperature behavior of fullerenes. We find that when C 60 and C 7O are maintained at temperatures above 1073 K, or are wxposed to hot metal surfaces, significant degradation occurs. We find an activation energy of 261.5 kJ/mol for this process. At temperatures below 873 K, no breakdown of fullerenes can be detected, even after heating for 6 hours. The effect of these findings on C 60 ion thruster design is discussed. Our present C 60 ion thruster experiment is also described.

fullerenes↗

Beyond ITER: Neutral beams for a demonstration fusion reactor (DEMO) (invited)

In the development of magnetically confined fusion as an economically sustainable power source, International Tokamak Experimental Reactor (ITER) is currently under construction. Beyond ITER is the demonstration fusion reactor (DEMO) programme in which the physics and engineering aspects of a future fusion power plant will be demonstrated. DEMO will produce net electrical power. The DEMO programme will be outlined and the role of neutral beams for heating and current drive will be described. In particular, the importance of the efficiency of neutral beam systems in terms of injected neutral beam power compared to wallplug power will be discussed. Options for improving this efficiency including advanced neutralisers and energy recovery are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗