Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nano”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Annealing influence on the microstructure of irradiated U-Mo monolithic fuel foils

In this study we compared the microstructure evolution of U-Mo fuel foils produced with and without heat treatment at low burn-up via advanced post-irradiation examination. The aim of this study is to observe after irradiation the ways in which the fabrication processes have influenced fuel behavior at early-stage irradiation, as for very low burn up microstructural studies are lacking. In this work it was observed that the larger grain size detected in the heat-treated samples before irradiation led to decreased grain refinement after irradiation. Grain refinement was associated with the presence of small nano-size bubbles and precipitates. This phenomenon is hypothesized to influence early fuel swelling during reactor irradiation. Grain refinement was also observed to increase in regions where γ-U decomposition was present. Thus, it was enhanced in the samples fabricated without heat treatment. The heat treatment also increased the thickness of the U-Mo/Zr interface, namely of the UZr 2 layer. However, the influence of this layer on fuel performance needs further investigation. On one side, it may contribute to better mechanical bonding; on the other, it may influence swelling and blistering in the interaction layer as porosity increases when this layer is increased. This was observed especially in the presence of increased area containing low Mo concentration, and thus containing a higher fraction of the α-U phase, which is highly susceptible to irradiation induced swelling. Strong evidence of reverse transformation under irradiation (α-U + γ'-U2Mo → bcc γ-U) was observed in these samples. While the precipitates (carbides and oxide) seem to be unaffected by the irradiation at these low burnups. However, further analyses are necessary at higher burn-up to assess the exact impact different heat treatments have on fuel performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Retention and surface morphology evaluation of fine-grain dispersion-strengthened tungsten for plasma-facing component applications

This study exposed novel fine-grain dispersion-strengthened tungsten (W) to high fluence, low energy deuterium (D) and helium (He) plasmas to evaluate how material microstructure and composition affect hydrogen retention and surface morphology. Tested materials included fine-grain dispersion-strengthened tungsten (DSW) with 3 wt% zirconium carbide (ZrC) dispersoids, fine-grain dense W without any dispersoids (FGW), and coarse-grained polycrystalline ‘ITER-grade’ W. Samples were exposed to D 2 + and He + plasmas at fusion-relevant fluences (∼10 25 m -2 ) and ion energies (75 eV) over a range of temperatures (200 °C, 300 °C, 450 °C for D, 850 °C for He). Helium ion microscopy was performed on the exposed samples to evaluate surface morphology changes and material integrity. After D plasma exposure, the ZrC dispersoids showed near-surface degradation at exposure temperatures above 300 °C, but no detrimental morphology changes were observed for the adjacent W grains. After He plasma-exposure, nano-structured fuzz formation was observed in the tungsten matrix of all samples. The ZrC dispersoids maintained their integrity despite the surrounding fuzz growth, with clear delineation between the W fuzz and dispersoid regions. Thermal desorption spectroscopy showed that ZrC DSW consistently retained more D than the FGW by about a factor of 2 across all temperatures. At 200 °C and 300 °C, the ITER-W displayed lower D retention than both the DSW and FGW, however at 450 °C ITER-W showed the highest retention, about 50% more than DSW. He retention was comparable across all samples, with the highest retention observed in the fine-grain W, only 26% higher than in ITER-W. These insights on retention behavior will inform further optimization of these novel fine-grained tungsten materials with and without dispersoid additives.

Dispersion-strengthened tungsten↗
DOE OSTI2021

Optical properties of differing nanolayered structures of divalent europium doped barium fluoride thin films synthesized by pulsed laser deposition

Optically-active thin films are employed in a variety of applications, such as LEDs and photovoltaics, due to their ability to act as up- or down-photon energy converters. Their performance depends critically on their composition and structure; thus, the use of novel synthesis techniques that allow for their control at the nanoscale level can result in improved efficiency and practicality. Here, layered thin films consisting of Eu 2+ - doped BaF 2 nanocrystalline layers separated by amorphous Al 2 O 3 were synthesized via sequential pulsed laser deposition using three separate targets for the different components; this synthesis technique provides precise control of layer thickness at the nanoscale along with dopant distribution within the film. Cross-sectional transmission electron microscopy analysis verified the desired nano-layering. Post-deposition heat treatments in a nitrogen atmosphere resulted in samples exhibiting steady emission with a broad peak ranging from 400 to 600 nm and a shoulder at 410 nm. The CIE 1931 chromaticity coordinates are x = 0.26-0.29 and y = 0.32-0.35 and vary as a function of the sample configuration. Because the chromaticity coordinates are close to those of a pure white light (x = 0.33, y = 0.33), these films demonstrate advantageous properties for applications with UV-pumped white light LEDs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

OLEDs on planarized light outcoupling-enhancing structures in plastic

Light extraction from OLEDs remains a challenge. While consumer demand for OLEDs in display technology continues to grow as prices decline, commercial use of OLEDs in solid state lighting (SSL) applications is lagging due to low light extraction, which results in low efficiency. Previous studies have been directed toward increasing the light extraction factor η out , but cost effective approaches that will enable high throughput and potential upscaling, as well as elucidation of the extraction process, are still lagging. One promising approach is the use of buried light extraction enhancing patterns that are planarized with a high refractive index (RI) layer. When adding substrate mode extracting means, the highest external quantum efficiencies (EQEs) were achieved using a complex approach of planarized vacuum nano holes. Here we present η out -enhancing planarized extraction structures (PES) in plastic. While plastic substrates currently present long-term stability issues and other drawbacks, as we show, they provide a tool for simple, inexpensive, and rapid generation of various enhancing structures that importantly can be transferred to the preferred rigid and flexible glass substrates. Moreover, plastic substrates are attractive for biomedical applications. The successful structures we present are easily scalable periodic corrugations, e.g., with pitch a ~ 4.25 µm and pitch/depth ratio a/h ~2.4 planarized by a layer of RI ~1.9, resulting in maximal EQEs exceeding 60% for a green OLED and 48.5% for a white OLED. Comparable increased EQEs were achieved for structures with a ~ 15 and 16 µm, and a/h ~ 2.1 and 4, respectively. Enhanced extraction was also observed with a very simply fabricated quasiperiodic nanohole array, and surprisingly, with a random shallow design. The latter is at variance with simulations based on diffraction only. Results are discussed in terms of a, h, and structural parameters together with scattering matrix simulations to assess the effect of various PES parameters and the nanoparticle-embedded planarizing layer on η out . The experiments and simulations indicate contributions of diffraction, reflection, and scattering to EQE enhancement.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Shear localization in metallic materials at high strain rates

Three factors govern adiabatic shear localization: strain hardening (or softening), strain-rate hardening, and thermal softening. It is typically associated with large shear strains (>1), high strain rates (10 3 –10 7 s –1 ), and high temperatures (40–100% of melting point), all of which happen within narrow regions with widths of about 1–200 μm. It is often an undesirable phenomenon, leading to failure, but there are situations where it is desirable, e. g., the generation of machining chips. Here, we review the development of both theoretical and experimental achievements, from the initiation of shear bands to their propagation with emphasis on three aspects: novel experimental techniques, novel materials, and nano/microstructural effects. The principal characteristics of adiabatic shear bands in metallic materials at the nano- and micro-scale are described. Bands that were formerly identified as transformed actually consist of nanocrystalline/ultrafine grains. These grains result from the breakup of the microstructure by a rotational recrystallization process. The evolution of the microstructure inside shear bands and their interactions for hcp, bcc, and fcc alloys, high-entropy alloys, nanocrystalline alloys, and metallic glasses are analyzed mechanistically. In conclusion, the gaps in the field and opportunities for future research are identified. Modern experimental characterization and computational techniques enable a more profound and predictive understanding of adiabatic shear localization and its avoidance in advanced materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The emerging field of block copolymer self-assembly-directed quantum materials

The area of functional materials derived from block copolymers (BCPs) as structure-directing agents for various inorganic materials has seen substantial growth as a result of the immense scientific as well as technological promise associated with such hybrid materials. Further, the convergence of BCP self-assembly with the fast-growing field of quantum materials now promises solution-based synthetic approaches to classes of materials that to date are dominated by stringent high-vacuum physical deposition techniques and bulk solid state chemical reactions. Moreover, the ensuing periodic nano- and mesostructures, a characteristic of BCP self-assembly, offer a unique platform for manipulating quantum-level properties, in turn resulting in substantial changes of macroscopic properties. This article will make a case for, review the existing work of, and provide our perspectives on this emerging field of block copolymer self-assembly directed quantum materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

X-ray computed tomography-based porosity analysis: Algorithms and application for porous woody biomass

The properties of lignocellulosic biomass, such as bulk physical, thermal, and mechanical properties, as well as the mobility of enzymes or catalysts, are largely affected by porosity, pore structures, and pore size distribution. While X-ray computed tomography (CT) has been introduced to effectively produce 3D volumetric images of material microstructure, a quantitative porosity analysis from the 3D images has never been done. This work introduces a first-of-its-kind X-ray CT-based quantitative porosity analysis method and applies the developed toolkit to characterize the internal porosity distribution of loblolly pine. A sample loblolly pine chip was scanned by a nano-resolution X-ray CT system and digitally reconstructed after a sequence of image processing operations. Here, a comprehensive porosity analysis was then performed to quantify the envelope porosity, the spatial distribution of local porosity, and the directional porosity. Solutions to the various challenges in image processing, porosity calculation, and large data handling are provided.

42 ENGINEERING↗
DOE OSTI2021

Production of desensitized, ultrafine PETN powder

Pentaerythritol tetranitrate (PETN) is a widely studied high explosive (HE), most commonly used in detonator applications. In this work, we use a spray drying technique to manufacture a new “nano-powder” morphology of PETN. The spray dried PETN is several orders of magnitude smaller in particle size than traditionally prepared PETN powders. The spray dried PETN has a mostly spherical and smooth morphology, while traditional crystalline PETN typically has sharp edges and crystal facets. Small-scale sensitivity tests including drop-weight impact, friction, and electrostatic discharge (ESD) indicate the spray dried PETN is less sensitive than traditionally used forms of PETN powders. Furthermore, we also observed no changes in chemical properties (melt temperature and onset of decomposition) after spray drying, and the material remains in the tetragonal, crystalline phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Design optimization of semiconductor piezoresistors with Schottky diode contacts

A modeling theory is developed to predict the performance of piezoresistors which incorporate Schottky diode electrical contacts. This new theory allows the design of high performance gauges which can be fabricated using NonLithographically-Based Microfabrication (NLBM) techniques. These semiconductor piezoresistors can be designed in customizable sizes and fabricated in parallel in order to integrate position sensing into MEMS flexural positioners. Customizable nanopositioning platforms will enable advances in a range of nano-scale fabrication and metrology applications. A semiconductor piezoresistor with Schottky diode contacts was fabricated and attached to a titanium flexure. This device is shown to match predicted electrical performance within about 8% and to show a gauge factor of 116, within 2% of the predicted value. Performance limits for Schottky diode semiconductor piezoresistors are identified to be about 127dB full noise dynamic range for a quarter bridge over a 10kHz sensor bandwidth on a 600µm width titanium flexure, making them ideal for sensing on meso-/micro-scale flexural positioners. Methods of reaching these performance bound are suggested and their impact on the sensor dynamic range are studied.

42 ENGINEERING↗
DOE OSTI2025

Graphene Oxide Nanoribbons for High Early-Strength Cement Concrete

Longitudinal oxidative unzipping of the outer walls of multiwalled carbon nanotubes (MWCNTs) yields graphene oxide nanoribbons (GONRs), which exhibit greater open surface area and functional edge content than MWCNTs. This paper presents a study of the nano-amendment of Portland cement concrete with GONRs in concentrations between 0.05% (in weight of cement, wt%) and 0.0005 wt%, thus up to two orders of magnitude lower than that reported as lower-bound in the archival literature. The dispersibility in aqueous solution as a function of GONR concentration and oxygen weight content (O%) was assessed through dynamic light scattering (DLS) and zeta potential analysis. The results indicated that less effective suspensions were obtained for 0.05 wt% of GONRs and 22.7 O%. Therefore, GONR water suspensions with 30-40% O% were used to manufacture 50 mm × 100 mm cylindrical concrete specimens. After 7 days of curing, results from uniaxial compression tests using four specimens per configuration (MWCNT concentration and O%) showed that the incorporation of GONRs resulted in an average increase in compressive strength up to 45%. Consistent with the DLS and compression test results, SEM micrographs showed well-dispersed GONRs together with accelerated and preferential formation of calcium silicate hydrates (C-S-H) for all GONR concentrations. The results indicate, for the first time, that the incorporation of very small concentrations (as low as 0.0005 wt%) of well-dispersed GONR amendments can significantly enhance the early-age concrete strength. However, such enhancement became insignificant after 28 days of curing.

cement↗
DOE OSTI2024

Nondestructive geochemical characterization of fossil hominin taphonomy and burial history

To date, only three Homo habilis specimens have been discovered that have associated craniodental and postcranial elements, providing a limited fossil record of the ontogeny and morphology of early members of the genus Homo. Recently, a nearly complete dentition, likely attributable to H. habilis, was discovered and excavated from early Pleistocene-age fluvial-lacustrine sediments of the upper Burgi Member of the Koobi Fora Formation at site F25787 in Area 13, near Ileret, Kenya. On the surface less than 15 m away, at site F25966, postcranial elements were found, which, if from the same individual as the nearby dentition, would represent the fourth associated craniodental and postcranial assemblage of this species. We developed a geochemical taphonomic history of these ca. 2 Ma hominin fossils using nondestructive X-ray based microanalytical tools (synchrotron and benchtop X-ray fluorescence chemical imaging and micro- and nano-computed tomography volumetric reconstruction), bulk analyses of sediments and paleosols at the excavation sites, and sedimentologic and stratigraphic observations. We integrate the chemical and physical taphonomic histories to test whether teeth (excavated in situ) and postcranial bones (eroded onto the outcrop surface) derive from a single individual. Minor differences in taphonomic history are attributable to the different biomineral properties of the dental and osseous components and to differences in physical damage during early post-mortem scavenging, dispersal, and burial in adjacent depositional settings. Microscale geochemical mapping enabled the temporal ordination of chemical and physical events in the specimens’ chemical taphonomic histories. Specifically, authigenic Fe- and K-bearing clays and Y, U, and Sr uptake occurred in post-burial fractures in bones and were also incorporated pervasively throughout dentin in teeth. Barite mineralization occurred along the latest fractures in both materials, and as a coating on tooth roots. The stratigraphic, taphonomic, and geochemical evidence supports the interpretation that the hominin fossils represent a single individual. Finally, successful application of these nondestructive sample characterization methods demonstrates capabilities for thorough interrogation of the taphonomic histories of other potential hominin fossil associations, enabling more robust and accurate palaeontologic constraints using those relationships.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermoluminescence and optically stimulated luminescence response of Al 2 O 3 coatings deposited by mist-chemical vapor deposition

Aluminum oxide (Al 2 O 3 ) is a widely used ceramic material which can be applied as a protective coating on metallic structures to improve corrosion resistance and mechanical properties. Al 2 O 3 also has great potential as a functional thin film device in optoelectronics. When it is doped with carbon (Al 2 O 3 :C), this material system can serve as a reliable radiation dosimeter. The combination of optoelectronic, dosimetric, and protective properties demonstrated by Al 2 O 3 uniquely positions it for dual use applications in nuclear forensics, nonproliferation and safeguards, emergency response, retrospective dosimetry, and nondestructive inspection. Here, in this study, an innovative ultrasonic mist-chemical vapor deposition (Mist-CVD) system was used to deposit thin (nm level) Al 2 O 3 coatings on 304 stainless steel substrates. The single aliquot regeneration (SAR) and additive dose reconstruction techniques were then used to investigate the thermoluminescence (TL) and optically stimulated luminescence (OSL) response of the coated substrates to increasing doses of β irradiation. This study demonstrates that nm-thick Al 2 O 3 coatings hold promise as novel nano-dosimeters which could be leveraged for a series of applications such as nonproliferation and safeguards, retrospective dosimetry, and nondestructive inspection.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Amorphous nonstoichiometric oxides with tunable room-temperature ferromagnetism and electrical transport

Material functionalities strongly depend on the stoichiometry, crystal structure, and homogeneity. Here we demonstrate an approach of amorphous nonstoichiometric inhomogeneous oxides to realize tunable ferromagnetism and electrical transport at room temperature. In order to verify the origin of the ferromagnetism, we employed a series of structural, chemical, and electronic state characterizations. Combined with electron microscopy and transport measurements, synchrotron-based grazing incident wide angle X-ray scattering, soft X-ray absorption and circular dichroism clearly reveal that the room-temperature ferromagnetism originates from the In 0.23 Co 0.77 O 1-v amorphous phase with a large tunable range of oxygen vacancies. The room-temperature ferromagnetism is tunable from a high saturation magnetization of 500 emu cm -3 to below 25 emu cm -3 , with the evolving electrical resistivity from 5 × 10 3 μΩ cm to above 2.5 × 10 5 μΩ cm. Inhomogeneous nano-crystallization emerges with decreasing oxygen vacancies, driving the system towards non-ferromagnetism and insulating regime. Our work unfolds the novel functionalities of amorphous nonstoichiometric inhomogeneous oxides, which opens up new opportunities for developing spintronic materials with superior magnetic and transport properties.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Influence of Polymer Type and Carbon Nanotube Properties on Carbon Nanotube/Polymer Nanocomposite Biodegradation

The interaction of anaerobic microorganisms with carbon nanotube/polymer nanocomposites (CNT/PNC) will play a major role in determining their persistence and environmental fate at the end of consumer use when these nano-enabled materials enter landfills and encounter wastewater. Motivated by the need to understand how different parameters (i.e., polymer type, microbial phenotype, CNT characteristics) influence CNT/PNC biodegradation rates, we have used volumetric biogas measurements and kinetic modeling to study biodegradation as a function of polymer type and CNT properties. In one set of experiments, oxidized multiwall carbon nanotubes (O-MWCNTs) with a range of CNT loadings 0 – 5% w/w were incorporated into poly-e-caprolactone (PCL) and polyhydroxyalkanoates (PHA) matrices and subjected to biodegradation by an anaerobic microbial community. For each CNT/PNC, complete polymer biodegradation was ultimately observed, although the rate of biodegradation was inhibited above certain critical CNT loadings dependent upon the polymer type. Higher loadings of pristine MWCNTs were needed to decrease the rate of polymer biodegradation compared to O-MWCNTs, an effect ascribed principally to differences in CNT dispersion within the polymer matrices. Above ertain CNT loadings, a CNT mat of similar shape to the initial PNC was formed after polymer biodegradation, while below this threshold, CNT aggregates fragmented in the media. In situations where biodegradation was rapid, methanogen growth was disproportionately inhibited compared to the overall microbial community. Analysis of the results obtained from this study indicates that the inhibitory effect of CNTs on polymer biodegradation rate is greatest under conditions (i.e., polymer type, microbial phenotype, CNT dispersion) where biodegradation of the neat polymer is slowest. This new insight provides a means to predict the environmental fate, persistence and transformations of CNT-enabled polymer materials.

Frank, Benjamin↗
DOE OSTI2023

Characterization of 3D printing filaments containing metal additives and their particulate emissions

Polylactic acid (PLA) filaments are widely used in fused filament fabrication (FFF) processes (3D printing). Filament additives such as metallic particles incorporated into PLA to modify functional and aesthetic features of print objects are becoming increasingly popular. However, the identities and concentrations of low percentage and trace metals in these filaments have not been well described in either the literature or product safety information included with the product. Here, we report the structures and concentrations of metals in selected Copperfill, Bronzefill and Steelfill filaments. We also report size-weighted number concentrations and size-weighted mass concentrations of particulate emissions as a function of print temperature for each filament. Particulate emissions were heterogenous in shape and size with airborne particles below 50 nm diameter dominating the size-weighted particle concentrations and larger particles (approximately 300 nm) dominating the mass weighted particle concentration. Results indicate that potential exposure to particles in the nano-size range increase when using print temperatures above 200o C. Because inhalation exposure to nanoparticles has been linked to adverse health outcomes, we suggest that using lower print temperatures for specific metal-fill filaments may reduce their operational hazard.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Origin of increased helium density inside bubbles in Ni (1–$x$) Fe $x$ alloys

Due to virtually no solubility, He atoms implanted or created inside materials tend to form bubbles, which are known to damage material properties through embrittlement. Higher He density in nano-sized bub- bles was observed both experimentally and computationally in Ni (1–$x$) Fe $x$ -alloy samples compared to Ni. The bubbles in the Ni (1–$x$) Fe $x$ -alloys were observed to be faceted, whereas in elemental Ni they were more spherical. Molecular dynamics simulations showed that stacking fault structures formed around bubbles at maximum He density. Higher Fe concentrations stabilize stacking fault structures, suppress evolution of dislocation network around bubbles and suppress complete dislocation emission, leading to higher He density.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Bicontinuous nanoporous design induced homogenization of strain localization in metallic glasses

Bicontinuous nanoporous metallic glasses (MG) synergize the outstanding properties of MGs and open-cell nanoporous materials. The low-density and high-specific-surface-area of bicontinuous nanoporous structures have the potential to enhance the applicability of MGs in catalysis, sensors, and lightweight structural designs. In this work, we report molecular dynamics simulations of tensile loading deformation and failure of bicontinuous nanoporous Cu 64 Zr 36 MG with 55% porosity and 4.4 nm ligament size. Results indicate an anomalous mechanical behavior featuring delocalized plastic deformation preceding ductile failure. The deformation follows two mechanisms: i) Necking of ligaments aligned with the loading direction and ii) progressive alignment of randomly oriented ligaments. Failure occurs at 0.16 strain, following massive rupture of ligaments. This work indicates that a bicontinuous nanoporous design is able to effectively delocalize strain localization in a MG due to a combination of size effect on the ductility of MGs resulting in nano ligaments necking and progressive asynchronous alignment of ligaments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermal Stability and Mechanical Properties of Cold-Sprayed Nickel-Yttria Coating

The microstructural evolution under the extreme environments imposed during cold spray deposition of cermet coatings and the microstructural recovery during post-processing annealing treatments is rather complex and not well understood. Here, Ni-Yttria cermet coatings on an SS304 substrate were produced using cold spray technique, resulting in a bimodal grain structure. The grain growth, phase stability, hardness, and wear properties are observed in as-deposited and annealed (at 400 °C) Ni-Yttria and pure Ni coatings. A multimodal microstructural characterization using electron microscopy, and atom probe tomography shows the structural and compositional stability of yttria particles and Ni grains. A fragmentation of Y-rich particles and dispersion in Ni was observed, however, no forced mixing/dissolution of Y in Ni is detected. Nano-yttria dispersed within the Ni grains slowed the grain growth during annealing. After annealing, Yttria reinforced coating was 1.5 times harder and showed better thermal and mechanical stability compared to the Ni coating.

Gwalani, Bharat↗