Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Tungsten oxide (WO{sub 3}) thin films for application in advanced energy systems

Inherent processes in coal gasification plants produce hazardous hydrogen sulfide (H{sub 2}S), which must be continuously and efficiently detected and removed before the fuel is used for power generation. An attempt has been made in this work to fabricate tungsten oxide (WO{sub 3}) thin films by radio-frequency reactive magnetron-sputter deposition. The impetus being the use of WO{sub 3} films for H{sub 2}S sensors in coal gasification plants. The effect of growth temperature, which is varied in the range of 30-500 deg. C, on the growth and microstructure of WO{sub 3} thin films is investigated. Characterizations made using scanning electron microscopy (SEM) and x-ray diffraction (XRD) indicate that the effect of temperature is significant on the microstructure of WO{sub 3} films. XRD and SEM results indicate that the WO{sub 3} films grown at room temperature are amorphous, whereas films grown at higher temperatures are nanocrystalline. The average grain-size increases with increasing temperature. WO{sub 3} films exhibit smooth morphology at growth temperatures {<=}300 deg. C while relatively rough at >300 deg. C. The analyses indicate that the nanocrystalline WO{sub 3} films grown at 100-300 deg. C could be the potential candidates for H{sub 2}S sensor development for application in coal gasification systems.

36 MATERIALS SCIENCE↗

Effects of deposition and annealing temperatures on the electrical and optical properties of Ag{sub 2}O and Cu{sub 2}O-Ag{sub 2}O thin films

Ag{sub 2}O and Ag{sub 2}O-Cu{sub 2}O films were deposited on glass substrates by magnetron sputtering of Ag and Cu targets at various substrate temperatures. After deposition, some of these films were annealed using a rapid thermal annealing system, with the variation of temperature. An UV-VIS-NIR photometer and a Hall measurement system were used to characterize the optical and electrical properties of these films. On annealing, Ag{sub 2}O (hexagonal) phase would slowly change to Ag+Ag{sub 2}O (cubic) phases when the annealing temperature is greater than 200 deg. C When the annealing temperature was higher than 450 deg. C, the Ag{sub 2}O phase would transform into a metallic Ag phase completely. Accordingly, the band gap of these films will change, along with the optical and electrical properties. In the study of Ag{sub 2}O-Cu{sub 2}O films, it is found that these two-phase composite films could exist obviously when deposited at room temperature. The photoinduced current of these composite films could be increased significantly, compared with that of a single Cu{sub 2}O phase. This is most likely due to that a large band gap semiconductor (Cu{sub 2}O) is coupled with a small band gap semiconductor (Ag{sub 2}O).

36 MATERIALS SCIENCE↗

In situ analyses on negative ions in the sputtering process to deposit Al-doped ZnO films

The origin of high energy negative ions during deposition of aluminum doped zinc oxide (AZO) films by dc magnetron sputtering of an AZO (Al{sub 2}O{sub 3}: 2.0 wt %) target was investigated by in situ analyses using the quadrupole mass spectrometer combined with the electrostatic energy analyzer. High energy negative oxygen (O{sup -}) ions which possessed the kinetic energy corresponding to the cathode sheath voltage were detected. The maximum flux of the O{sup -} ions was clearly observed at the location opposite to the erosion track area on the target. The flux of the O{sup -} ions changed hardly with increasing O{sub 2} flow ratio [O{sub 2}/(Ar+O{sub 2})] from 0% to 5%. The kinetic energy of the O{sup -} ions decreased with decreasing cathode sheath voltage from 403 to 337 V due to the enhancement of the vertical maximum magnetic field strength at the cathode surface from 0.025 to 0.100 T. The AZO films deposited with the lower O{sup -} bombardment energy showed the higher crystallinity and improved the electrical conductivity.

36 MATERIALS SCIENCE↗

Fabrication of plastic biochips

A versatile surface functionalization procedure based on rf magnetron sputtering of silica was performed on poly(methylmethacrylate), polycarbonate, polypropylene, and cyclic olefin copolymers (Topas 6015). The hybrid thermoplastic surfaces were characterized by x-ray photoelectron spectrometer analysis and contact angle measurements. The authors then used these hybrid materials to perform a sandwich assay targeting an HIV-1 antibody using fluorescent detection and biotinylated peptides immobilized using the bioaffinity of biotin-neutravidin. They found a limit of detection similar to arrays on glass surfaces and believed that this plastic biochip platform may be used for the development of disposable immunosensing and diagnostic applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrical resistivity change in Al:ZnO thin films dynamically deposited by bipolar pulsed direct-current sputtering and a remote plasma source

The Al-doped ZnO (AZO) thin films for a transparent conducting oxide in solar cell devices were deposited by bipolar pulsed dc magnetron sputtering. This work was performed in an in-line type system and investigated AZO films in a static deposition mode and dynamic one, which is more important in the practical fields. Because of this dynamic deposition process, the zigzagged columnar structure was observed. This resulted in the decreasing electrical property, optical properties, and surface roughness. As a deposition in the dynamic mode, the resistivity increased from 1.64x10{sup -3} to 2.50x10{sup -3} {Omega} cm, as compared to that in the static mode, and the transmittance also decreased from 83.9% to 78.3%. To recover the disadvantage, a remote plasma source (RPS) was supported between the substrate and target for reducing zigzagged formation during the deposition. The deposition rate decreased by using RPS, but the electrical and optical properties of films got better than only dynamic mode. The resistivity and transmittance in the dynamic mode using RPS were 2.1x10{sup -3} {Omega} cm and 85.5%, respectively. In this study, the authors found the possibility to advance the electrical and optical properties of AZO thin films in the industry mode.

36 MATERIALS SCIENCE↗

Lithium phosphorus oxynitride solid-state thin-film electrolyte deposited and modified by bias sputtering and low temperature annealing

Amorphous lithium phosphorus oxynitride (LiPON) solid-state thin-film electrolyte has been deposited and characterized. The thin films were prepared by rf magnetron sputtering under various substrate biases. By fabricating under different substrate biases and applying low temperature annealing (473 K), the properties of the LiPON thin-film electrolytes and the electrolyte/cathode interfaces were modified. The ionic conductivity as high as 9.4x10{sup -4} S m{sup -1} can be obtained by depositing at optimal bias. The performances of the consequently fabricated SnO{sub 2}/LiPON/LiMn{sub 2}O{sub 4} all-solid-state lithium ion thin-film batteries were improved using the bias sputtering technique, due to the enhanced the ionic conductivity and uniform interface.

36 MATERIALS SCIENCE↗

Control of bombardment energy and energetic species toward a superdense titanium nitride film

TiN deposited by dc magnetron sputtering has been widely used as a hard mask material for dielectric patterning in multilevel Cu interconnects. Typically inside a ''poison-mode'' regime, the film density is 4.5-4.9 g/cm{sup 3}. The microstructure, varying from columnar structure to nanocrystalline, is controlled by both thermodynamics and surface kinetics through ionization, substrate bias, target voltage, etc. A relatively low density film can be correlated with a porous columnar structure, low mechanical robustness, and weak resistance to plasma etching. However, with controlled growth, an applied substrate bias does not create resputtering and crystal defects. Instead, the authors create film with a maximum density of 5.3 g/cm{sup 3}. In this high density film, carrier scatterings through grain boundary are greatly suppressed and the film resistivity is as low as 95 {mu}{Omega} cm, which brings additional benefits as a conductive capping layer. As it is deposited at room temperature, the process minimizes the thermal budget to the underlying low-k dielectric materials to be patterned.

36 MATERIALS SCIENCE↗

Temperature threshold for nanorod structuring of metal and oxide films grown by glancing angle deposition

Thin films of tin (Sn), aluminum (Al), gold (Au), ruthenium (Ru), tungsten (W), ruthenium dioxide (RuO{sub 2}), tin dioxide (SnO{sub 2}), and tungsten trioxide (WO{sub 3}) were grown by glancing angle deposition (GLAD) to determine the nanostructuring temperature threshold, {Theta}{sub T}, above which adatom surface diffusion becomes large enough such that nanorod morphology is no longer formed during growth. The threshold was found to be lower in metals compared to oxides. Films were grown using both dc and pulsed dc magnetron sputtering with continuous substrate rotation over the temperature range from 291 to 866 K. Film morphologies, structures, and compositions were characterized by high resolution scanning electron microscopy, x-ray diffraction, and x-ray photoelectron spectroscopy. Films were also grown in a conventional configuration for comparison. For elemental metals, nanorod structuring occurs for films with melting points higher than that of Al (933 K) when grown at room temperature with a rotation rate of {approx}5 rpm, corresponding to a value of {Theta}{sub T}{approx_equal}0.33{+-}0.01. For the oxide films, a value of {Theta}{sub T}{approx_equal}0.5 was found, above which GLAD nanorod structuring does not occur. The existence of a nanostructuring temperature threshold in both metal and oxide GLAD films can be attributed to greater adatom mobilities as temperature is increased resulting in nonkinetically limited film nucleation and growth processes.

36 MATERIALS SCIENCE↗

Deposition of ultrathin AlN films for high frequency electroacoustic devices

The authors investigate the microstructure, crystal orientation, and residual stress of reactively sputtered aluminum nitride (AlN) films having thicknesses as low as 200 down to 25 nm. A two-step deposition process by the dual cathode ac (40 kHz) powered S-gun magnetron enabling better conditions for AlN nucleation on the surface of the molybdenum (Mo) bottom electrode was developed to enhance crystallinity of ultrathin AlN films. Using the two-step process, the residual in-plane stress as well as the stress gradient through the film thickness can be effectively controlled. X-ray rocking curve measurements have shown that ultrathin films grown on Mo using this technology are highly c-axis oriented with full widths at half maximum of 1.8 deg. and 3.1 deg. for 200- and 25-nm-thick films, respectively, which are equal to or even better than the results previously reported for relatively thick AlN films. High-resolution transmission electron microscopy and fast Fourier transform analyses have confirmed strong grain orientation in 25-100-nm-thick films. A fine columnar texture and a continuous lattice microstructure within a single grain from the interface with the Mo substrate through to the AlN surface have been elicited even in the 25-nm-thick film.

36 MATERIALS SCIENCE↗

Transparent conductive Al-doped ZnO thin films grown at room temperature

Aluminum-doped ZnO (ZnO:Al, AZO) thin films were prepared on glass substrates by dc reactive magnetron sputtering from a Zn-Al alloy target at room temperature. The effects of the Ar-to-O{sub 2} partial pressure ratios on the structural, electrical, and optical properties of AZO films were studied in detail. AZO films grown using 100:4 to 100:8 Ar-to-O{sub 2} ratio result in acceptable quality films with c-axis orientated crystals, uniform grains, 10{sup -3} {Omega} cm resistivity, greater than 10{sup 20} cm{sup -3} electron concentration, and high transmittance, 90%, in the visible region. The lowest resistivity of 4.11x10{sup -3} {Omega} cm was obtained under the Ar-to-O{sub 2} partial pressure ratio of 100:4. A relatively strong UV emission at {approx}3.26 eV was observed in the room-temperature photoluminescence spectrum. X-ray photoelectron spectroscopy analysis confirmed that Al was introduced into ZnO and substitutes for Zn and doped the film n-type.

36 MATERIALS SCIENCE↗

Transparent conductive and near-infrared reflective Ga-doped ZnO/Cu bilayer films grown at room temperature

Bilayer films consisting of Ga-doped ZnO (GZO) and Cu layers were grown at room temperature by magnetron sputtering. The structural, electrical, and optical properties of GZO/Cu bilayer films were investigated in detail. The crystallinity and transparent-conductive properties of the films were correlated with the Cu layer thickness. The GZO/Cu bilayer film with the Cu layer thickness of 7.8 nm exhibited a low resistivity of 7.6x10{sup -5} {Omega} cm and an average visible transmittance of 74%. The reflectance was up to 65% in the near-infrared region for this film. The transparent conductive and near-infrared reflective GZO/Cu bilayer films could be readily deposited at room temperature. The GZO/Cu bilayer films were thermally stable when annealed at temperatures as high as 500 deg. C.

36 MATERIALS SCIENCE↗

Effect of oxygen deficiency on the photoresponse and reactivity of mixed phase titania thin films

Nonstoichiometric mixed phased titania nanocomposites (TiO{sub 2-x}) were deposited by reactive direct current magnetron sputtering. The authors explored the role of nonstoichiometry (as defined by oxygen deficiency in synthesis) in mixed phase titania thin films and its effects on the photoresponse and photocatalytic performance for CO{sub 2} reduction to methane under UV and visible light. Oxygen partial pressure was varied during film deposition, yielding different levels of oxygen deficiency in the films. Optimized nonstoichiometric films showed a strong redshift. The authors have identified an optimum set of synthesis conditions for TiO{sub 2-x} films that produce a relative maximum in photocatalytically produced methane under both UV and visible light.

36 MATERIALS SCIENCE↗

Effects of thermal annealing on the microstructure of sputtered Al{sub 2}O{sub 3} coatings

The morphology and microstructure of Al{sub 2}O{sub 3} thin films deposited by pulsed direct current magnetron sputtering were studied in the as-grown state and after vacuum annealing at 1000 deg. C for 12 h using transmission electron microscopy. For the coating deposited under low ion bombardment conditions, the film consists of small {gamma}- and/or {delta}-Al{sub 2}O{sub 3} grains embedded in an amorphous matrix. The grain size at the region close to the interface to the substrate was much larger than that of the remaining layer. Growth of the {gamma}-Al{sub 2}O{sub 3} phase is promoted during annealing but no transformation to {alpha}-Al{sub 2}O{sub 3} was detected. For high-energetic growth conditions, clear evidence for {gamma}-Al{sub 2}O{sub 3} formation was found in the upper part of the coating with grain size much larger than for low-energetic growth, but the film was predominately amorphous at the interface region. Annealing resulted in the transformation of {gamma}-Al{sub 2}O{sub 3} to {alpha}-Al{sub 2}O{sub 3}, while the mainly amorphous part crystallized to {gamma}-Al{sub 2}O{sub 3}.

36 MATERIALS SCIENCE↗

Optical and electrical properties of transparent conducting B-doped ZnO thin films prepared by various deposition methods

B-doped ZnO (BZO) thin films were prepared with various thicknesses up to about 500 nm on glass substrates at 200 deg. C by dc or rf magnetron sputtering deposition, pulsed laser deposition (PLD), and vacuum arc plasma evaporation (VAPE) methods. Resistivities of 4-6 x 10{sup -4}{Omega} cm were obtained in BZO thin films prepared with a B content [B/(B + Zn) atomic ratio] around 1 at. % by PLD and VAPE methods: Hall mobilities above 40 cm{sup 2}/Vs and carrier concentrations on the order of 10{sup 20} cm{sup -3}. All 500-nm-thick-BZO thin films prepared with a resistivity on the order of 10{sup -3}-10{sup -4}{Omega} cm exhibited an averaged transmittance above 80% in the wavelength range of 400-1100 nm. The resistivity in BZO thin films prepared with a thickness below about 500 nm was found to increase over time with exposure to various high humidity environments. In heat-resistance tests, the resistivity stability of BZO thin films was found to be nearly equal to that of Ga-doped ZnO thin films, so these films were judged suitable for use as a transparent electrode for thin-film solar cells.

36 MATERIALS SCIENCE↗

Optical transparency and electrical conductivity of nonstoichiometric ultrathin In{sub x}O{sub y} films

The effect of thickness and composition on the electrical conductivity and optical transparency, mainly in the infrared, of ultrathin In{sub x}O{sub y} films was studied. In{sub x}O{sub y} films 35-470 A thick with oxygen atomic fractions of {approx}0.3 and {approx}0.5 were prepared via dc magnetron sputtering. All films were polycrystalline, consisting of only the cubic bixbiyte phase of In{sub 2}O{sub 3}. The average grain size of the films increased from 30 to 95 nm as the film thickness increased. The weak dependence of the electrical conductivity on the frequency and the low activation energies for conduction, a few hundredths of an eV, provided an indication that free band conduction was the primary electrical conduction mechanism in the case of all ultrathin In{sub x}O{sub y} films. It was found that introducing a high degree of nonstoichiometry in the form of oxygen deficiency did not help improve the electrical conductivity, since not all vacancies contributed two free electrons for conduction and due to impurity scattering. The optical nature of these films, studied mainly by ellipsometry, was found to be dependent on the film's composition and thickness. In the infrared, the dielectric function of all In{sub x}O{sub y} films was consistent with the Drude model, inferring that the transparency loss in this region was a result of free charge carriers. In the visible however, In{sub x}O{sub y} films under 170 A, which had an oxygen atomic fraction of {approx}0.5, were modeled by extending the Drude model to the shorter wavelengths. Films over 170 A, with the same composition, were modeled using the Cauchy dispersion model, meaning that no absorption was measured. These results indicate that, optically, under specific compositions, ultrathin In{sub x}O{sub y} films undergo a transition from metalliclike behavior to dielectric behavior with increasing film thickness. Using a figure of merit approach, it was determined that a nonstoichiometric 230 A thick In{sub x}O{sub y} film, with an oxygen atomic fraction of {approx}0.3, had the best combination of conductivity and transparency, namely, absorption of less than 20% in the infrared, about 10% in the visible, and electrical resistance of only 230 {Omega} at 20 kHz. Such a film may be classified as a highly conductive transparent oxide even in the infrared.

36 MATERIALS SCIENCE↗

Ultrathin TiSiN overcoat protection layer for magnetic media

TiSiN ultrathin films (10-50 A) deposited by reactive magnetron sputtering from Ti{sub x}Si{sub y} targets were used as anticorrosion overcoats to protect Co-containing recording media. Films' growth, structure, composition, resistance against hydrolysis, and anticorrosion performances were studied by spectroscopy (x-ray reflectivity and diffraction, ellipsometry, x-ray photoelectron spectroscopy, Fourier transform infrared reflection-absorption spectroscopy) and simulated by molecular dynamics (using modified Tersoff-type interatomic interactions). TiSiN ultrathin overcoats were found to be dense amorphous oxynitrides containing Ti-O-Si linkages. The conversion of SiN{sub x} into SiO{sub x} by hydrolysis was prevented by introducing less than 20 at. % of Ti in the films. Thanks to the formation of Ti-O-Si linkages which densify the films and reduce oxygen diffusion, good corrosion protection of the magnetic media was achieved down to 28 A TiSiN overcoat thickness.

36 MATERIALS SCIENCE↗

Formation of tetragonal or monoclinic ZrO{sub 2} coatings by oxygen plasma treatment of Zr{sub 74.7}Cu{sub 19.7}Nb{sub 5.6} glassy thin films

The authors report on the production of stable nanostructured tetragonal and/or monoclinic ZrO{sub 2} nanopillars achieved by means of oxygen plasma treatment of ternary Zr{sub 74.7}Cu{sub 19.7}Nb{sub 5.6} glassy films. The Zr-based metallic glass thin films were successfully deposited by magnetron sputtering and subsequently subjected to oxygen plasma for various exposure times. The compositions of the oxidized films were determined by Auger electron spectroscopy and X-Ray photoelectron spectroscopy depth profiling while the surface morphology was evaluated by means of atomic force microscopy and scanning electron microscopy. X-Ray diffraction was used for the structural analysis. Our results show that, depending on the length of time of oxygen plasma treatment, tetragonal and/or monoclinic ZrO{sub 2} films can be formed, the surface morphology of which exhibit nanopillar structures with an increased effective surface. These findings provide an easy and efficient way for growing ZrO{sub 2} coatings with a predefined structure suitable for protective and possibly for catalytic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Zirconium nitride films deposited in (Ar + N{sub 2} + H{sub 2}) sputtering atmosphere: Optical, structural, and electrical properties

Zr-N films were grown on glass substrates via radio-frequency magnetron sputtering using an Ar + N{sub 2} + H{sub 2} mixture. Hydrogen was employed in order to reduce oxygen contamination coming from background pressure, as confirmed by secondary ion mass spectroscopy analysis. The tuned process parameter was the nitrogen flux percentage (R{sub N2}) in the mixture. The crystallographic structure of the films was studied using x-ray diffraction. The measurements show that the films deposited at low R{sub N2} (lower than or equal to 50%) crystallize in the rocksalt ZrN structure. As R{sub N2} exceeds 50%, the film exhibits the co-presence of ZrN and Zr{sub 3}N{sub 4} (denoted as o-Zr{sub 3}N{sub 4}) phases. When the deposition is performed in only nitrogen atmosphere (R{sub N2} = 100%), a broad peak located at 2{theta}{approx_equal} 32.2 deg. is mainly attributed to the contribution coming from (320) planes of the o-Zr{sub 3}N{sub 4}. An envelope method, based on the optical reflection and transmission spectra taken at normal incidence, has been applied for the optical characterization of the nitride films. Such a method allows the determination of the samples' average thickness and optical constants (refractive index n and extinction coefficient k) in the ultraviolet-visible-near infrared regions. The evaluated thickness was about 2500 nm, which is in good agreement with the value obtained from profilometry. The absorption coefficient {alpha} was calculated from reflectance and transmittance spectra. The energy bandgap ranges from 2.3 eV to 2.4 eV. Electrical characterization was performed using capacitance-voltage measurements, which showed that the films evolve from insulating to semiconductor behavior when the nitrogen content in the sputtering atmosphere is decreased, confirming structural and optical results.

36 MATERIALS SCIENCE↗