Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Liquid flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Probe measures gas and liquid mass flux in high mass flow ratio two-phase flows

Deceleration probe constructed of two concentric tubes with separator inlet operates successfully in flow fields where ratio of droplet flow rate to gas flow rate ranges from 1.0 to 20, and eliminates problems of local flow field disturbances and flooding. Probe is effective tool for characterization of liquid droplet/gas spray fields.

Burick, R. J.↗

Heat and momentum transfer model studies applicable to once-through, forced convection potassium boiling

A number of heat transfer and fluid flow mechanisms that control once-through, forced convection potassium boiling are studied analytically. The topics discussed are: (1) flow through tubes containing helical wire inserts, (2) motion of droplets entrained in vapor flow, (3) liquid phase distribution in boilers, (4) temperature distributions in boiler tube walls, (5) mechanisms of heat transfer regime change, and (6) heat transfer in boiler tubes. Whenever possible, comparisons of predicted and actual performances are made. The model work presented aids in the prediction of operating characteristics of actual boilers.

Sabin, C. M.↗

Steady-state temperature distribution within a Brayton rotating unit operating in a power conversion system using helium-xenon gas

The Brayton rotating unit (BRU), consisting of a turbine, an alternator, and a compressor, was tested as part of a Brayton cycle power conversion system over a side range of steady state operating conditions. The working fluid in the system was a mixture of helium-xenon gases. Turbine inlet temperature was varied from 1200 to 1600 F, compressor inlet temperature from 60 to 120 F, compressor discharge pressure from 20 to 45 psia, rotative speed from 32 400 to 39 600 rpm, and alternator liquid-coolant flow rate from 0.01 to 0.27 pound per second. Test results indicated that the BRU internal temperatures were highly sensitive to alternator coolant flow below the design value of 0.12 pound per second but much less so at higher values. The armature winding temperature was not influenced significantly by turbine inlet temperature, but was sensitive, up to 20 F per kVA alternator output, to varying alternator output. When only the rotational speed was changed (+ or - 10% of rated value), the BRU internal temperatures varied directly with the speed.

Johnsen, R. L.↗

Design and test of porous-tungsten mercury vaporizers

New design requirements for porous plug-type vaporizers used with Kaufman thrusters and thruster arrays are discussed. The results of testing samples of porous tungsten for mercury flow rate, liquid intrusion pressure level, and mechanical strength are presented. Nitrogen gas was used instead of mercury vapor for approximate calibration. Liquid intrusion pressure levels will require that flight thruster systems with long feedlines have restrictions in the dynamic line during launch.

Kerslake, W. R.↗

Cavitation in liquid cryogens. 1: Venturi

The results of continuing cavitation studies are reported. The cavitation characteristics of liquid hydrogen and liquid nitrogen flowing in a transparent plastic Venturi are discussed. Thermodynamic data, consisting of pressure and temperature measurements within fully developed hydrogen cavities, are reported. Details concerning test apparatus, test procedure, and data correlation techniques are given.

Hord, J.↗

Solar neutrinos, Martian rivers, and Praesepe.

Some recent papers on solar neutrinos, Martian rivers, and Praesepe stars are reviewed. Possible causes of solar neutrino detection rates being below theoretical expectations are quoted. The widespread presence of sinuous dendritic channels on Mars is noted. The occurrence of earth-like epochs on Mars is indicated as a plausible explanation for many such channels in terms of surface liquid water flows. The roughly uniform distribution of the Praesepe stars through the main sequence width is viewed as the indication that the excursion time off the main sequence is comparable to the time between mixings.

Sagan, C.↗

Liquid-cooled liner for helmets

Liner acts as coolant tubing, manifold, and supporting structures. Fabric of waffle-design is made of several integrated channels (or capillaries) through which coolant liquid can flow. Thin and light-weight liner can be incorporated into any type of helmet or head gear.

Williams, B. A.↗

Impinging jet separators for liquid metal magnetohydrodynamic power cycles

In many liquid metal MHD power, cycles, it is necessary to separate the phases of a high-speed liquid-gas flow. The usual method is to impinge the jet at a glancing angle against a solid surface. These surface separators achieve good separation of the two phases at a cost of a large velocity loss due to friction at the separator surface. This report deals with attempts to greatly reduce the friction loss by impinging two jets against each other. In the crude impinging jet separators tested to date, friction losses were greatly reduced, but the separation of the two phases was found to be much poorer than that achievable with surface separators. Analyses are presented which show many lines of attack (mainly changes in separator geometry) which should yield much better separation for impinging jet separators).

Bogdanoff, D. W.↗

Measurement component technology. Volume 1: Cryogenic pressure measurement technology, high pressure flange seals, hydrogen embrittlement of pressure transducer material, close coupled versus remote transducer installation and temperature compensation of pressure transducers

The results are presented of an investigation into the availability and performance capability of measurement components in the area of cryogenic temperature, pressure, flow and liquid detection components and high temperature strain gages. In addition, technical subjects allied to the components were researched and discussed. These selected areas of investigation were: (1) high pressure flange seals, (2) hydrogen embrittlement of pressure transducer diaphragms, (3) The effects of close-coupled versus remote transducer installation on pressure measurement, (4) temperature transducer configuration effects on measurements, and (5) techniques in temperature compensation of strain gage pressure transducers. The purpose of the program was to investigate the latest design and application techniques in measurement component technology and to document this information along with recommendations for upgrading measurement component designs for future S-2 derivative applications. Recommendations are provided for upgrading existing state-of-the-art in component design, where required, to satisfy performance requirements of S-2 derivative vehicles.

Hayakawa, K. K.↗

Major and trace element abundances in samples from the lunar highlands

Analyses for major elements, REE, Co, Cr, Cs, Ga, Hf, Ni, Rb, Sc, and Zn have been done on samples of Apollo 16 rocks 60025, 60335, 64455, 65015, 67075, and 67629 and on fines 60601, 61221, 61241, 64501, 65701, 67601, and 69941. FeO, Na2O, REE, Co, Cr, Hf, and Sc have been determined in four 4-5 mg chips from 65015 and 20 individual, 2.5-9.5 mg fragments from 65702. It appears that trace element characteristics of small fragments are similar to those of larger rocks. No simple mixing relationship was found among KREEP basalts, VHA basalts, anorthosites, fines, and meteorites. Balances could not be simultaneously achieved for Al2O3 and LIL elements, using analyzed samples as end members for mixing models. Most samples analyzed have negative Eu anomalies, in contrast to the positive anomalies expected for plagioclase cumulates. Most samples may be derived from LIL-rich liquids that flowed into highland valleys.

Haskin, L. A.↗

Characterization of exothermic brazing components Skylab experiment M552

Information developed to characterize flight and ground based samples from the Exothermic Brazing Experiment is detailed. Included is information developed from metallographic observation, chemical analysis, and measurements of component dimensions. Comparisons of the flight and ground based specimens showed that good quality brazes were obtained. Effects of the zero gravity processing were noted on liquid metal flow and braze alloy-base metal reactions. Unusual metallurgical structures exhibited in the nickel brazes made in Skylab were the result of composition variations apparently related to the time-temperature cycle characteristic of this braze.

Pattee, H. E.↗

Transport of liquid state nitrogen through long length service lines during thermal/vacuum testing

Physical and analytical aspects associated with the transport are presented. Included is a definition of the problems and difficulties imposed by the servicing of a typical solid cryogen system, as well as a discussion of the transport requirements and of the rationale which governed their solution. A successful detailed transport configuration is defined, and the application of established mathematics to the design approach is demonstrated. The significance of head pressure, pressure drop, line friction, heat leak, Reynolds number, and the fundamental equilibrium demands of pressure and temperature were examined as they relate to the achievement of liquid state flow. Performance predictions were made for the transport system, and several analytical quantities are tabulated. These data are analyzed and compared with measured and calculated results obtained while actually servicing a solid cryogen system during thermal/vacuum testing.

Florio, F. A.↗

Design study of steady-state 30-tesla liquid-neon-cooled magnet

A design for a 30-tesla, liquid-neon-cooled magnet was reported which is capable of continuous operation. Cooled by nonboiling, forced-convection heat transfer to liquid neon flowing at 2.8 cu m/min in a closed, pressurized heat-transfer loop and structurally supported by a tapered structural ribbon, the tape-wound coils with a high-purity-aluminum conductor will produce over 30 teslas for 1 minute at 850 kilowatts. The magnet will have an inside diameter of 7.5 centimeters and an outside diameter of 54 centimeters. The minimum current density at design field will be 15.7 kA/sq cm.

Prok, G. M.↗

Zero-leak valve

Zero-leakage valve has fluid-sealing diaphragm support and flat sievelike sealing surface. Diaphragm-support valve is easy to fabricate and requires minimum maintenance. Potential applications include isolation valve for waste systems and remote air-actuated valve. Device is also useful in controlling flow of liquid fluorine and corrosive fluids at high pressures.

Macglashan, W. F., Jr.↗

Conceptual design of two-phase fluid mechanics and heat transfer facility for spacelab

Five specific experiments were analyzed to provide definition of experiments designed to evaluate two phase fluid behavior in low gravity. The conceptual design represents a fluid mechanics and heat transfer facility for a double rack in Spacelab. The five experiments are two phase flow patterns and pressure drop, flow boiling, liquid reorientation, and interface bubble dynamics. Hardware was sized, instrumentation and data recording requirements defined, and the five experiments were installed as an integrated experimental package. Applicable available hardware was selected in the experiment design and total experiment program costs were defined.

North, B. F.↗

Surface texturing of fluoropolymers

A method is disclosed for improving surface texture for adhesive bonding, metal bonding, substrate plating, decal substrate preparation, and biomedical implant applications. The surface to be bonded is dusted in a controlled fashion to produce a disbursed layer of fine mesh particles which serve as masks. The surface texture is produced by impinging gas ions on the masked surface. The textured surface takes the form of pillars or cones. The bonding material, such as a liquid epoxy, flows between the pillars which results in a bond having increased strength. For bonding metals a thin film of metal is vapor or sputter deposited onto the textured surface. Electroplating or electroless plating is then used to increase the metal thickness in the desired amount.

Banks, B. A.↗

Fluid/Vapor Separator for Variable Flow Rates

Shutter varies gas throughput of porous plug. Variable area exposed on porous plug allows to pass varying rates of vapor flow while blocking flow of liquid helium II from cryogenic bath. Applications in refining operations, industrial chemistry, and steam-powered equipment.

Lee, J. M.↗

Elimination of a discrete frequency acoustical phenomenon associated with the Space Shuttle main engine oxidizer valve-duct system

In the development of the Space Shuttle Main Engines, various unpredictable dynamical phenomena were experienced which resulted in engine shutdown or failures, e.g., fires. One such dynamical phenomenon consisted of an acoustical buzz at 7200 Hz in the vicinity of the main oxidizer valve. The method of isolating the buzz phenomenon, identifying the mechanism, and developing a fix to eliminate the buzz is presented together with supporting data. These data, i.e., fluctuating pressure and acceleration data, were obtained from hot firing engine tests and from liquid nitrogen flow simulation tests conducted at Marshall Space Flight Center.

Schutzenhofer, L. A.↗