Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOADING RATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Influence of fatigue crack wake length and state of stress on crack closure

The location of crack closure with respect to crack wake and specimen thickness under different loading conditions was determined. The rate of increase of K sub CL in the crack wake was found to be significantly higher for plasticity induced closure in comparison to roughness induced closure. Roughness induced closure was uniform throughout the thickness of the specimen while plasticity induced closure levels were 50 percent higher in the near surface region than in the midthickness. The influence of state of stress on low-high load interaction effects was also examined. Load interaction effects differed depending upon the state of stress and were explained in terms of delta K sub eff.

Telesman, Jack↗

Load interaction effects on fatigue crack growth in Ti-6Al-4V alloy

The importance of delay, retardation in the rate of fatigue crack growth, produced by load interactions in variable amplitude loading, on the accurate prediction of fatigue lives of engineering structures is discussed. The effects of a broad range of loading variables on delay in fatigue crack growth at room temperature are examined for a mill annealed Ti-6Al-4V alloy. The results are used to estimate crack growth behavior under programmed loads.

Wei, R. P.↗

A performance comparison of the Cray-2 and the Cray X-MP

A suite of thirteen large Fortran benchmark codes were run on Cray-2 and Cray X-MP supercomputers. These codes were a mix of compute-intensive scientific application programs (mostly Computational Fluid Dynamics) and some special vectorized computation exercise programs. For the general class of programs tested on the Cray-2, most of which were not specially tuned for speed, the floating point operation rates varied under a variety of system load configurations from 40 percent up to 125 percent of X-MP performance rates. It is concluded that the Cray-2, in the original system configuration studied (without memory pseudo-banking) will run untuned Fortran code, on average, about 70 percent of X-MP speeds.

Schmickley, Ronald↗

CO 2 Oxidative Ethane Dehydrogenation on CeO 2 /SiO 2 ‐Supported NiFe 3 Catalysts

CO 2 -assisted oxidative dehydrogenation of ethane is a sustainable alternative to steam cracking for ethylene production. In this study, a series of CeO 2 on SiO 2 supported NiFe 3 catalysts were synthesized by incipient wetness impregnation and tested for oxidative dehydrogenation performance. The CeO 2 /SiO 2 supported catalysts with high weight loading of CeO 2 (50%–75%) provided higher activity than the lower CeO 2 (0%–25%) loaded catalysts (with ethylene production rates of 0.62–0.98 µmol/g cat /s and 0.19–0.3 µmol/g cat /s, respectively) while maintaining high ethylene selectivity (43%–45%). In contrast, the NiFe 3 supported on only CeO 2 also exhibited high activity (ethylene production rate of 0.71 µmol/g cat /s), but the ethylene selectivity (16%) was greatly decreased compared to the mixed system. Temperature programmed reduction, X-ray diffraction, and Raman spectroscopy all indicate the creation of a solid solution of the Fe and Ni doped into the CeO 2 crystal structure in the catalysts with high CeO 2 loading/bulk CeO 2 support. Here, the high ethylene selectivity in the high CeO 2 loading catalysts indicates that the Fe is preferentially creating the solid solution, with the decrease in selectivity observed in the CeO 2 -only supported catalyst likely resulting from CeO 2 interacting directly with Ni, creating Ni-CeO X interfaces that are known active sites for the unwanted side reaction of dry reforming.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Glass Formulation Development and Testing for DWPF High AI 2 O 3 HLW Sludges (Final report)

The principal objective of the work described in this Final Report is to develop and identify glass frit compositions for a specified DWPF high-aluminum based sludge waste stream that maximizes waste loading while maintaining high production rate for the waste composition provided by ORP/SRS. This was accomplished through a combination of crucible-scale, vertical gradient furnace, and confirmation tests on the DM100 melter system. The DM100-BL unit was selected for these tests. The DM100-BL was used for previous tests on HLW glass compositions that were used to support subsequent tests on the HLW Pilot Melter. It was also used to process compositions with waste loadings limited by aluminum, bismuth, and chromium, to investigate the volatility of cesium and technetium during the vitrification of an HLW AZ-102 composition, to process glass formulations at compositional and property extremes, and to investigate crystal settling on a composition that exhibited one percent crystals at 963°C (i.e., close to the WTP limit).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Skylab experiment M-171 'Metabolic Activity' - Results of the first manned mission

The experiment was performed to ascertain whether man's ability to perform mechanical work would be altered as a result of exposure to the weightless environment. Skylab II crewmen were exercised on a bicycle ergometer at loads approximating 25%, 50%, and 75% of their maximum oxygen uptake while their physiological responses were monitored. The results of these tests indicate that the crewmen had no significant decrement in their response to exercise during their exposure to zero gravity. Immediately postflight, however, all crewmen demonstrated an inability to perform the programmed exercise with the same metabolic effectiveness as they did both preflight and inflight. The most significant changes were elevated heart rates for the same work load and oxygen consumption (decreased oxygen pulse), decreased stroke volume, and decreased cardiac output at the same oxygen consumption level. It is apparent that the changes occurred inflight, but did not manifest themselves until the crewmen attempted to readapt to the 1-G environment.

Michel, E. L.↗

The Kinematics of Treadmill Locomotion in Space

Locomotion on a treadmill in 0 G will probably remain a centerpiece of NASA's exercise countermeasures programme. This form of physical activity has the potential to cause large bone and muscle forces as well as loading during a period of continuous treadmill exercise. A critical concern is the provision of a treadmill which can approximate 1 G performance in space. At this point, no adequate objective measurements of in-flight treadmill kinetics or of the human response to this activity have been made. Interpretation of the results obtained in the present study is limited by the following: (1) bungee tensions were not measured; (2) ground reaction forces were not measured in parallel with the kinematic measurements; and (3) the instrumentation used to film the astronauts could itself have been affected by microgravity. Despite these shortcomings, what is apparent is that exercise during NASA missions STS 7 and STS 8 resulted in leg motions that were similar to those found during 1 G locomotion on an inclined passive treadmill and on an active treadmill at an even steeper grade. In addition, it was apparent that the majority of the loads were transmitted through the forefoot, and one can surmise that this style of running would result in physiologically significant tensions in the calf musculature and resultant ankle compressive loading. Further speculation regarding limb loading is complicated by the fact that varying amounts of force are transmitted through (1) the treadmill handle and (2) bungee cords that act as a tether. New generations of treadmills are being manufactured that could provide I important information for planners of long-duration space missions. If these types of treadmill are flown on future missions, it will be possible to control bungee tensions more precisely, control for grade and speed, and, most importantly, provide data on the rates and magnitudes of limb loading. These data could then be incorporated into biomechanical models of the lower limb to more fully understand mechanisms of load transmission from distal to proximal structures and to optimize in-flight exercise protocols in such a way that muscle and bone loss could be reduced.

Thornton, W. E.↗

AGC-2 Disassembly Report

The Next Generation Nuclear Plant (NGNP) Graphite Research and Development (R&D) Program is currently measuring irradiated material properties for predicting the behavior and operating performance of new nuclear graphite grades available for use within the cores of new very high temperature reactor designs. The Advanced Graphite Creep (AGC) experiment, consisting of six irradiation capsules, will generate irradiated graphite performance data for NGNP reactor operating conditions. The AGC experiment is designed to determine the changes to specific material properties such as thermal diffusivity, thermal expansion, elastic modulus, mechanical strength, irradiation induced dimensional change rate, and irradiation creep for a wide variety of nuclear grade graphite types over a range of high temperature, and moderate doses. A series of six capsules containing graphite test specimens will be used to expose graphite test samples to a dose range from 1 to 7 dpa at three different temperatures (600, 900, and 1200°C) as described in the Graphite Technology Development Plan. Since irradiation induced creep within graphite components is considered critical to determining the operational life of the graphite core, some of the samples will also be exposed to an applied load to determine the creep rate for each graphite type under both temperature and neutron flux. All six AGC capsules in the experiment will be irradiated in the Advanced Test Reactor (ATR). AGC-1 and AGC-2 will be irradiated in the south flux trap and AGC-3–AGC-6 will be irradiated in the east flux trap. The change in flux traps is due to NGNP irradiation priorities requiring the AGC experiment to be moved to accommodate Fuel irradiation experiments. After irradiation, all six AGC capsules will be cooled in the ATR Canal, sized for shipment, and shipped to the Materials and Fuels Complex (MFC) where the capsule will be disassembled in the Hot Fuel Examination Facility (HFEF). During disassembly, the metallic capsule will be machined open and the individual samples removed from the interior graphite body containing the samples. Samples removed from the capsule will be loaded in a shipping drum and shipped to the Idaho National Laboratory (INL) Research Center (IRC) for initial post-irradiation examination (PIE) and storage for any future testing at the newly completed Carbon Characterization Laboratory (CCL). All work was performed under an ASME NQA-1-2008;1a-2009 compliant quality assurance program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dynamics of confined reactive water in Smectic clay-zeolite composites.

The dynamics of water confined to mesoporous regions in minerals such as swelling clays and zeolites is fundamental to a wide range of resource management issues impacting many processes on a global scale, including radioactive waste containment, desalination, and enhanced oil recovery. Large-scale atomic models of freely diffusing multilayer smectite particles at low hydration confined in a silicalite cage are used to investigate water dynamics in the composite environment with the ReaxFF reactive force field over a temperature range of 300 647 K. The reactive capability of the force field enabled a range of relevant surface chemistry to emerge, including acid/base equilibria in the interlayer calcium hydrates and silanol formation on the edges of the clay and inner surface of the zeolite housing. After annealing, the resulting clay models exhibit both mono- and bilayer hydration structures. Clay surface hydration redistributed markedly and yielded to silicalite water loading. We find that the absolute rates and temperature dependence of water dynamics compare well to neutron scattering data and pulse field gradient measures from relevant samples of Ca-montmorillonite and silicalite, respectively. Within an atomistic, reactive context, our results distinguish water dynamics in the interlayer Ca(OH)2 nH2O environment from water flowing over the clay surface, and from water diffusing within silicalite. We find that the diffusion of water when complexed to Ca hydrates is considerably slower than freely diffusing water over the clay surface, and the reduced mobility is well described by a difference in the Arrhenius pre-exponential factor rather than a change in activation energy.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fatigue Crack Closure Analysis Using Digital Image Correlation

Fatigue crack closure during crack growth testing is analyzed in order to evaluate the critieria of ASTM Standard E647 for measurement of fatigue crack growth rates. Of specific concern is remote closure, which occurs away from the crack tip and is a product of the load history during crack-driving-force-reduction fatigue crack growth testing. Crack closure behavior is characterized using relative displacements determined from a series of high-magnification digital images acquired as the crack is loaded. Changes in the relative displacements of features on opposite sides of the crack are used to generate crack closure data as a function of crack wake position. For the results presented in this paper, remote closure did not affect fatigue crack growth rate measurements when ASTM Standard E647 was strictly followed and only became a problem when testing parameters (e.g., load shed rate, initial crack driving force, etc.) greatly exceeded the guidelines of the accepted standard.

Leser, William P.↗

On the Strain Rate Sensitivity Measured by Nanoindentation at High Strain Rates

The flow stress of a material can be strongly dependent on the rate of applied strain. Measuring the strain rate sensitivity can reveal key insights into the mechanisms that drive plastic deformation. Indentation techniques have been developed to measure the strain rate sensitivity at quasistatic strain rates, but accessing higher strain rate regimes has been saddled with experimental and technical challenges. With state-of-the-art indentation instrumentation now capable of recording load and displacement at data acquisition rates in excess of 1.25 MHz, we report how strain rate sensitivity testing methodologies, especially those aimed for higher indentation strain rates, may be validated using the well-studied time-dependent deformation behavior of tungsten. Here, the strain rate sensitivity for a (110) single crystal is shown to be consistent (m = 0.023 at 2 µm depth) across all tested strain rates and methods ranging from 10 -2 - 10 4 1/s.

36 MATERIALS SCIENCE↗

Electrochemical performance and stability of the cathode for solid oxide fuel cells. V. high performance and stable Pr 2 NiO 4 as the cathode for solid oxide fuel cells

The polarization loss due to oxygen reduction at the cathode in solid oxide fuel cells is a thermally activated process; therefore, as temperature is lowered, the loss becomes substantial. Highly active cathodes have been investigated by several groups; equally important, if not more, is the stability of these electrodes. The high performance and stable Pr 2 NiO 4 cathode was studied by impedance spectroscopy and dc current–potential sweeping methods. The power density in Pr 2 NiO 4 -based anode supported button cells was in the range between 0.65 and 0.7 W/cm 2 at 750 degrees C at the external load of 0.8 V. The degradation rate at 0.8 V was approximately 3% per 1000 h up to 2000 h. The electrode resistance is a function of external loads, thus also varies with current densities. The relationship between electrode resistance and external loads is non-linear, which may changes in lattice oxygen nonstoichiometry of the cathodes.

25 ENERGY STORAGE↗

Vent modification of large ribbon parachutes to enhance cluster performance

Due to uneven load sharing and lagging inflation rates, the design of the Large Main Parachute (LMP) cluster, used to recover the Space Shuttle steel case Solid Rocket Boosters, had to be modified. The cause of the problem was excessive variation in effective porosity in the crown area of the LMP during first stage inflation. The design modification consisted of adding horizontal ribbons above the existing vent band to reduce the vent porosity and better control the position and attitude of the vent lines. Performance of modified LMP's since introduction indicates that the load sharing between the clustered chutes has been significantly improved.

Kolega, D. J.↗

Operando FTIR investigation of salt dynamics in Li-ion batteries during fast charging

Li-ion batteries, when charged at fast-charging rates ($>$2C), suffer from reduced lifetimes and can undergo catastrophic failure. During high-rate charging, Li-ions are unable to rapidly transport through high-loading electrodes ($>$4 mAh cm −2 ). This results in unequal charge distributions, potentials, and utilization of the active material, which can lead to Li plating. Li-ion concentration polarization, in which Li-ions deplete in the anode and accumulate in the cathode during charging, precedes Li plating. An operando FTIR-ATR graphite/NMC cell developed in this research captured Li-ion concentration polarization in real-time. During fast charging, decreases in Li-ion concentration ($>$95%) were measured at the back of the anode. This is the first verification of complete Li-ion depletion within the anode at high C-rates. The measurements also showed graphite stage transition. A P2D model was developed for comparison to the operando measurements. The measurements agreed with the model in some cases, but disparities existed at high C-rates and loadings. In the experiment, the Li-ion concentration often failed to recover to 1.2 M until several hours after charging, whereas the model Li-ion concentration rapidly recovered. The contrast between the model and experiment results indicates that further investigation is required to improve understanding of Li-ion concentration dynamics during fast charging.

25 - ENERGY STORAGE↗

Io escape and ionization of atmospheric gases

Exploratory model calculations for the Io atomic oxygen cloud have provided two-dimensional sky-plane intensities for the 6300 A, 1304 A and 880 A lines, where volume excitation and ionization rates are determined by impact collisions with Io plasma torus electrons. Comparison of model results with observations at 6300 A suggests an isotropic oxygen flux from Io of about 1.5x109 atoms 1 sq cm/sec. The effects of including a neutral sulfur cloud and also of including charge exchange reactions between plasma torus ions and neutral OI and SI were evaluated to be significant and were roughly estimated to increase the required oxygen flux to 1.2 x 10 to the 10th atoms/sq cm/sec. In addition, increases in the estimates for the ion loading, cloud mass loss, plasma mass loading and ion energy input rates were also made. Model calculations for an Io sulfur cloud, excluding charge exchange reactions but assuming an SI flux of 7.5 x 10 to the 8th atoms/sq cm/sec (i.e., half of the oxygen flux), were also performed and provided sky plane intensities for a number of visible and IR emission lines.

Smyth, W. H.↗

Maximizing long-term biohydrogen production with Clostridium thermocellum for high solids conversion of lignocellulosic biomass

Biological hydrogen production from lignocellulosic biomass sustainably couples organic waste reduction with renewable energy generation. Efficient conversion is challenged by the structural complexity of lignocellulose and resulting recalcitrance to enzymatic degradation. Clostridium thermocellum natively breaks down biomass with highly effective hemi-/cellulases systems (i.e., cellulosomes) and generates hydrogen in anaerobic cultivation, creating a compelling platform for lignocellulosic biohydrogen production. Achieving commercially viable production rates requires balancing high biomass loading and throughput against uniform mixing conditions required for enzyme dispersion, pH and temperature control, and efficient hydrogen and metabolite removal in continuous operation. To address these barriers to process intensification, we implemented novel reactor and process designs for high-solids lignocellulosic biomass fermentations using the C. thermocellum KJC19-9 strain, genetically engineered for co-utilization of cellulose and hemicellulose sugars (i.e., xylose). Via computational fluid dynamics (CFD) modeling and experimental validation, we achieved a >50% improvement in biohydrogen production with an improved anchor-type impeller morphology, coupled to a threefold reduction in agitation rate. To further reduce rheological constraints and accumulation of toxic metabolites, we then transitioned the process to sequencing fed-batch operation. The resulting process generated 24.87 L H 2 L −1 from 160 g L −1 of deacetylated and mechanically refined (DMR)-pretreated corn stover biomass over 16 days while solubilizing >95% of influent cellulose and hemicellulose, setting a new performance benchmark for continuous production of biohydrogen from lignocellulose.

08 HYDROGEN↗

Demonstration of the On-the-Fly Shielding Analysis Method: Spent Fuel and Waste Disposition

This report documents work performed supporting the US Department of Energy (DOE) Office of Nuclear Energy (NE) Spent Fuel and Waste Disposition (SFWD) Integrated Waste Management activities under work breakdown structure element 1.08.02.04.01, “Data and Tools Development, Validation, and Maintenance.” In particular, this report fulfills milestone M3SF-21OR020401016, “Implement on-the-fly dose analysis methodology in UNF-ST&DARDS” within work package SF-21OR02040101, “Commercial SNF Characterization - ORNL.” The Used Nuclear Fuel - Storage, Transportation & Disposal Analysis Resource and Data System (UNFST& DARDS) enables automated dose rate calculations for spent nuclear fuel (SNF) transportation packages and storage casks using a Monte Carlo radiation transport code. The explicit method uses a detailed model of the SNF system and its contents. Therefore, a dose rate calculation is required for each as-loaded transportation package or storage cask because the SNF assemblies within a canister typically have unique irradiation characteristics. An alternate method, referred to as the “on-the-fly” shielding analysis method, has been proposed that requires only a set of Monte Carlo dose rate calculations for each transportation packaging/storage cask design. The results of the Monte Carlo dose rate calculations are independent of the SNF assembly irradiation and decay characteristics. The dose rate values may then be combined with the radiation source strength of the SNF assemblies associated with a particular transportation packaging/storage cask design to determine actual dose rates. This report presents on-the-fly dose rate calculations for a representative SNF storage cask and verification of the on-the-fly dose rate calculation results by comparison with reference dose rate calculations using the explicit Monte Carlo dose rate calculation. The on-the-fly shielding analysis method was implemented in UNF-ST&DARDS. A Python program was developed to process the MAVRIC dose rate results obtained by source particle type, energy group, and fuel geometry region. A Python processor created binary files, which were saved as a special UNF-ST&DARDS library for on-the- fly shielding analyses. UNF-ST&DARDS uses the precalculated on-the-fly binary libraries generated by the Python data processor and directly executes the Python code for on-the-fly dose analysis. This Python code unzips the pre-generated binary files mentioned above, reads the data, and combines them with user-specified sources for dose and uncertainty calculations. The Python programs were verified using Excel calculations and by comparison with the values obtained with the MAVRIC post-processing utilities applied to the 3dmap files. This method can currently be used to determine dose rates for as-loaded HI-STORM FW storage casks. The UNF-ST&DARDS analysis wizard for on-the-fly shielding analysis is described in this report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ethane dehydrogenation over manganese oxides supported on ZSM-5 zeolites

Mn-ZSM5 catalysts are shown to have high reaction rates, C 2 H 4 selectivity and stability for the ethane dehydrogenation reaction. The specific reaction rate increases with the Mn loading until the optimal Mn amount of 3.4 wt% for zeolites with a Si/Al ratio of 12. Structure characterizations and spectra analysis have unveiled that this catalyst contains MnO 2 nanoparticles on the zeolite external surface and (MnOH) + groups on the external surface of the zeolite. The MnO 2 nanoparticles contain the catalytic sites for ethane dehydrogenation while the (MnOH) + groups help stabilize the oxide particles, leading to the high stability of the Mn-ZSM5 catalyst for EDH. As a result, the Mn-ZSM5 samples can catalyze EDH for over 150 h at 600 °C with a high reaction rate (>10 mmol C 2 H 6 g cat –1 h –1 ) and high C 2 H 4 selectivity (>98%). Finally, the spent catalyst can also be regenerated by calcination in dry or wet air (3% steam).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗