Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GaGe”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A new technique to infer convective rainfall from satellite infrared cloud observations

GLAS-2, a modified version of the GLAS-1 technique developed by Negri et al. (1984) for estimating convective precipitation from GEO-satellite IR data, is introduced and demonstrated on the data set for the Florida Area Cumulus Experiment in 1980. In GLAS-2, rain cells are located by identification of all local blackbody-temperature minima below 253 K in an array of GOES digital data, and rain parameters are assigned on the basis of the one-dimensional cloud model of Adler and Mack (1984). The demonstration results are presented in graphs and tables and compared with those of GLAS-1 and a number of other methods as well as radar and rain-gage measurements. The false-alarm rate for GLAS-2 is found to be 0.54, somewhat better than that of other satellihte methods; further improvements are suggested.

Negri, A. J.↗
NASA NTRS1985

Transient technique for measuring heat transfer coefficients on stator airfoils in a jet engine environment

A transient technique was used to measure heat transfer coefficients on stator airfoils in a high-temperature annular cascade at real engine conditions. The transient response of thin film thermocouples on the airfoil surface to step changes in the gas stream temperature was used to determine these coefficients. In addition, gardon gages and paired thermocouples were also utilized to measure heat flux on the airfoil pressure surface at steady state conditions. The tests were conducted at exit gas stream Reynolds numbers of one-half to 1.9 million based on true chord. The results from the transient technique show good comparison with the steady-state results in both trend and magnitude. In addition, comparison is made with the STAN5 boundary layer code and shows good comparison with the trends. However, the magnitude of the experimental data is consistently higher than the analysis.

Gladden, H. J.↗
NASA NTRS1984

Heat transfer investigation in the junction region of circular cylinder normal to a flat plate at 90 deg location

External heat-transfer rates were measured on a flat plate in the junction region of a circular cylinder mounted normal to the plate at a location 90 deg from the stagnation point. This configuration simulates the junction of the shroud with gas-turbine vanes. Heat-transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.14 with gas temperatures of approximately 750 deg R over a flat plate at room temperature. The measurements were made in air for a unit Reynolds number, Re/cm, range of 11,000 to 58,000. Heat-transfer measurements were conducted in the 70-ft long, 4-in. diameter shock tube. A shock-wave reflection technique was used to produce a flow Mach number of 0.14. Thin-film platinum heat gages were mounted on the flat plate and along the line of the stagnation point of the cylinder to measure the local heat flux in the junction region. The experimental heat-transfer data were correlated with the laminar and turbulent boundary-layer theories for the flat plate. With the cylinder the heat fluxes on the flat plate were greatly increased in the junction region compared to the heat flux for the plate alone.

Nagamatsu, H. T.↗
NASA NTRS1985

An experimental investigation of a swirling, axisymmetric, turbulent boundary layer with pressure gradient

The results of an experimental investigation designed to document data on both mean and turbulence quantities in the axisymmetric, swirling boundary layer (with and without a pressure gradient) flowing over a stationary cylinder downstream of a spinning cylindrical section are discussed. The pressure gradient was introduced into the flow field by a 25.4-mm-high, forward-facing circular step mounted on the stationary cylinder, the step height being nearly equal to the approaching boundary-layer thickness. All the measurements were made at upstream reference velocity of 36-37 m/sec, with the rotation of the spinner set to make its peripheral speed equal to the reference velocity. The data reported include measurements of surface pressure and the mean surface-shear-stress vector (using a miniature directional surface-fence gage) and oil-flow visualization studies of the stationary cylinder. The data indicate that the streamwise pressure gradient controls the development of the streamwise component of wall shear but leaves the peripheral component of wall shear practically unaffected.

Hebbar, S. K.↗
NASA NTRS1984

Summary of workshop on the application of VLSI for robotic sensing

It was one of the objectives of the considered workshop to identify near, mid, and far-term applications of VLSI for robotic sensing and sensor data preprocessing. The workshop was also to indicate areas in which VLSI technology can provide immediate and future payoffs. A third objective is related to the promotion of dialog and collaborative efforts between research communities, industry, and government. The workshop was held on March 24-25, 1983. Conclusions and recommendations are discussed. Attention is given to the need for a pixel correction chip, an image sensor with 10,000 dynamic range, VLSI enhanced architectures, the need for a high-density serpentine memory, an LSI-tactile sensing program, an analog-signal preprocessor chip, a smart strain gage, a protective proximity envelope, a VLSI-proximity sensor program, a robot-net chip, and aspects of silicon micromechanics.

Brooks, T.↗
NASA NTRS1986

Pseudolog Digital-to-Analog Converter

Sensitivity decreases by 10 at beginning of each input decade. Method conceived to convert binary-coded data to suitable linear form for stripchart recording. Strip-chart recordings obtained from typical pressure readings in a vacuum system during pumpdown. In reading curve, BCD digital vacuum-gage output processed by analog-to-digital converter in such way that only reading digits (but not range) appear in output. In range and reading, range also converted to analog and placed as most significant digit.

Gooder, S. T.↗
NASA NTRS1985

Fluid Flow in Crystal Growth: Analysis of the Verticle Bridgman and Floating Zone Process

Research is aimed at the fundamental understanding of the interactions of heat and mass transport and fluid mechanics in crystal growth from the melt, especially in how it pertains to experiments supported by the Microgravity Science and Applications program. Emphasis has been on studies of the vertical Bridgman system, on small-scale floating zone systems proposed for space flight, and on quantitative prediction of nonlinear transitions in melt/solid interface morphologies leading to the formation of dendrites in directional solidification. The analysis of vertical Bridgman growth has lead to the complete numerical analysis of transport phenomena in directional solidification and to a detailed comparison of calculations to the GaGe growth experiments of Wang and Witt. Calculations show the central role of the ampoule material in determining the radial temperature gradients in the melt and thus, the intensity of convection. Results indicate that diffusion-controlled growth can not be achieved on Earth with conventional growth systems, but are feasible in microgravity

Brown, R. A.↗
NASA NTRS1985

Solutal Convection and Its Effects on Crystal Growth and Segregation in Binary and Pseudo-Binary System with Large Liquidus-Solidus Separation

This research program is composed of theoretical and experimental studies of solutal convection and its effects on crystal growth and segregation in binary and pseudo-binary systems with large liquidus-solidus separation. The theoretical program has resulted in the development of a transient simulation of the growth of concentrated alloys in microgravity and has been used to study the dynamics of GeSi, PbSnTe, HgCdTe growth. Finite element analysis has also been developed for studying the interactions of buoyancy-driven convection in the melt caused by temperature and concentration variations with melt-solid interface morphology and alloy segregation in the grown crystal. These calculations are being compared directly to experimental measurements of segregation and interface shape for GeSi growth and GaGe growth. The results for SiGe indicate that careful design of the thermal system can result in almost diffusion-controlled growth on Earth because of the stablizing influence of the concentration gradient ahead of the solidification front.

Brown, R. A.↗
NASA NTRS1983

Demonstration test of burner liner strain measurement systems: Interim results

Work is in progress to demonstrate two techniques for static strain measurements on a jet engine burner liner. Measurements are being made with a set of resistance strain gages made from Kanthal A-1 wire and via heterodyne speckle photogrammetry. The background of the program is presented along with current results.

Stetson, K. A.↗
NASA NTRS1986

Impact dynamics instrumentation

One of the tasks specified in the NASA Langley controlled impact demonstration (CID) work package was to furnish dynamic instrumentation sensors. The types of instrumentation sensors required were accelerometers for aircraft structural loads measurements, seat belt load cells to measure anthropomorphic dummy responses to the aircraft impact, and strain gage bending bridges to measure the aircraft fuselage and wing bending during impact. The objective in the selection of dynamic instrumentation for the CID was to provide 352 of the highest quality transducers and remain within budget allocation. The transducers that were selected for the CID evaluation process were each subjected to rigorous laboratory acceptance tests and to aircraft fuselage section drop tests at the LaRC Impact Dynamics Research Facility. Data compiled from this series of tests showed the selected transducers to be best suited for the CID mission requirement. The transducers installation technique on the airframe proved successful. The transducer quality assurance was guaranteed through rigorous acceptance testing. Data acquired was 97.0%.

Mccormck, R. F.↗
NASA NTRS1986

Structureborne noise in aircraft: Modal tests

As part of an investigation to develop measurement techniques for structureborne noise, three modal surveys have been conducted on an OV-10A aircraft and the results have been presented. The purpose of the modal surveys was to identify suitable locations for mounting accelerometer and strain gages in subsequent tests in which transfer functions relating wing vibration to interior noise were to be determined. These surveys are as follows:(1) wing/fuselage modal survey utilizing one shaker under the right wing; (2) complete wing modal survey utilizing two shakers, one under each wing; and (3) fuselage side panel modal survey utilizing a small instrumented hammer. The predominant frequencies and damping ratios for each analysis were listed in tables. The primary mode shapes at the lower frequencies and at frequencies near the expected engine driving frequencies have been shown for each survey.

Clevenson, S. A.↗
NASA NTRS1985

The origin of the 1883 Krakatau tsunamis

Three hypotheses proposed to explain possible causes of the Aug. 27, 1883 Krakatau tsunamis were analyzed: (1) large-scale collapse of the northern part of Krakatau island (Verbeek, 1884), (2) submarine explosion (Yokoyama, 1981), and (3) emplacement of pyroclastic flows (Latter, 1981). A study of timings of the air and sea waves between Krakatau and Batavia, showing that no precise sea wave travel times can be obtained, and a study of the tide and pressure gage records made on August 27, indicating that the air and sea waves were propagated from the focus of eruption on Krakatau island, suggest that neither hypothesis 2 or 3 are sufficiently substantiated. In addition, the event that caused the major air and sea wave was preceded (by 40 min) by a similar, smaller event which generated the second largest tsunami and an air wave. It is concluded that the most likely mechanism for the eruption is a Mt. St. Helens scenario, close to the hypothesis of Verbeek, in which collapse of part of the original volcanic edifice propagated a major explosion.

Francis, P. W.↗
NASA NTRS1986

Wind tunnel test evaluation of a Shuttle derived launch system

The Shuttle Derived Vehicle (SDV) is a proposed unmanned launch system configured using Shuttle elements. The SDV incorporates two solid rocket boosters, an external tank and three Space Shuttle main engines identical to those used in the present Space Transportation System. Two new elements, a recoverable propulsion/avionics module housing the main engines and an expendable payload module, complete the SDV configuration. This paper describes the activities and results of wind tunnel tests conducted to validate the aerodynamic and controllability characteristics of SDV configurations. The configuration variables consisted of the payload module diameter, length and nose shape. The tests were conducted in the NASA/Marshall Space Flight Center 14 inch trisonic wind tunnel. Aerodynamic force and moment data were obtained over a Mach number range of 0.6 to 4.96. The attack and sideslip angles were varied + or - 8.0 deg. Forces and moments were measured by a sting-supported six component strain gage balance.

Tewell, J. R.↗
NASA NTRS1985

Longitudinal compressive failure modes in fiber composites End attachment effects on IITRI type test specimens

The end-attachment effects on longitudinal compressive strength of IITRI type specimen unidirectional fiber composites are formally assessed using finite-element analysis (FEA) in conjunction with composite mechanics. Sixteen different cases were analyzed to evaluate end-attachment effects (such as degree of misalignment, type of misalignment, progressive end-tab debonding, and specimen thickness) on stress distribution, peak stresses, buckling loads, and buckling mode shapes. The results obtained from the FEA and comparisons with fractured specimens show that eccentricities induce bending-type stresses which peak near the end-tabs and cause flexural type fracture. Also, guidelines are included for placing back-to-back strain gages to measure the presence/absence of possible end-attachment and eccentricity effects.

Chamis, C. C.↗
NASA NTRS1985

Effects of strain rate on delamination fracture toughness of graphite/epoxy

The objective of this paper is to evaluate various experimental techniques and analysis methods for the characterization of interlaminar fracture toughness, and to determine the effects of strain rate on that property for a graphite/epoxy composite. Mode I interlaminar fracture was investigated by means of a double-cantilever beam (DCB) specimen for AS-4/3501-6 graphite/epoxy. Hinged tabs were used to insure unrestrained rotation at the free ends. Specimens were loaded at quasi-static deflection rates of up to 8.5 mm/s corresponding to crack extension rates of over 51 mm/s. Crack extension was monitored by means of strain gages mounted on the surface of the specimen, or a conductive-paint circuit attached to the edge of the DCB specimen. Continuous records were obtained of load, deflection, and crack extension for determination of the strain energy release rate. The latter was expressed as a power law of the crack extension velocity. Results indicate that the strain energy release rate increases with crack velocity by up to 28 percent for the range of rates considered.

Daniel, I. M.↗
NASA NTRS1985

Your space suit and you - Significance of manloading in pressure suit design

Data collection on man-induced loads borne by space suits is discussed, with emphasis on the glove area. The distinction between the 'potential' maximum manload (measured according to the 95 percentile male outside the suit), and the actual manload experienced by the suit or 'limit manload', is stressed. Limit manload data for the glove were collected using a glove with finger and metacarpal joints and a hard shell to support strain gages. Potential manload data are theorized to exceed the limit manload (as corroborated by entire suit limit load data presented for the Apollo and Shuttle suits) because of load sharing within the fabric configuration, test inputs being at values other than 95 percentile values, and the restraint line acting like a spring and preventing the load from being induced. This, however, is not borne out by the glove test data, illustrating the difficulty of measuring the man/machine interface. Design load is determined by adding he pressure load and the limit load after compensations have been made for load splitting. Finally, a method for better testing, used in the design of an improved mobility glove for the Space Shuttle program, is presented.

Rouen, M.↗
NASA NTRS1986

Drop testing and analysis of six-foot diameter graphite-epoxy frames

Graphite-epoxy frames were drop tested onto a concrete floor to simulate crash loadings. The frames have Z-shaped cross-sections typical of designs often proposed for fuselage structure of advanced composite transports. The 6-foot diameter of the frames was chosen to reduce specimen fabrication costs and to facilitate testing. Response of the frames from accelerometer, strain gage, and photographic measurements are presented which characterize the behavior under 25-30 fps vertical impact velocity onto concrete. Failure of the graphite-epoxy frames involved a complete separation through the cross section near the impact point. All damage to the composite frame was confined to an area close to the impact point. Failure of aluminum frames tested for comparison were different from the composite specimens. The aluminum frames yielded (plastic hinges formed) at several locations around the lower portion of the frame without failing completely across the section.

Boitnott, R. L.↗
NASA NTRS1985

Development of a temperature-compensated hot-film anemometer system for boundary-layer transition detection on high-performance aircraft

A hot-film constant-temperature anemometer (CTA) system was flight-tested and evaluated as a candidate sensor for determining boundary-layer transition on high-performance aircraft. The hot-film gage withstood an extreme flow environment characterized by shock waves and high dynamic pressures, although sensitivity to the local total temperature with the CTA indicated the need for some form of temperature compensation. A temperature-compensation scheme was developed and two CTAs were modified and flight-tested on the F-104/Flight Test Fixture (FTF) facility at a variety of Mach numbers and altitudes, ranging from 0.4 to 1.8 and 5,000 to 40,000 ft respectively.

Chiles, H. R.↗