SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Program provides design information for low-drag, high-drag-divergence, Mach number isolated nacelles suitable for use with advanced high-bypass-ratio, turbofan engines. One element is development of method to predict inviscid pressure distribution and flow field about arbitrary axisymmetric ducted body at transonic speeds.
A Technology Utilization Program for the dissemination of information on technological developments which have potential utility outside the aerospace community is presented. The 21 items reported herein describe programs that are applicable to electronic circuit design procedures.
Computerized design criteria for turbomachinery and the constraints imposed by very high rotational fields are presented along with a variety of computerized design criteria of interest to structural designers.
There are no author-identified significant results in this report.
The HD 220 program was created as part of the space shuttle solid rocket booster recovery system definition. The model was generated to investigate the damage to SRB components under water impact loads. The random nature of environmental parameters, such as ocean waves and wind conditions, necessitates estimation of the relative frequency of occurrence for these parameters. The nondeterministic nature of component strengths also lends itself to probabilistic simulation. The Monte Carlo technique allows the simultaneous perturbation of multiple independent parameters and provides outputs describing the probability distribution functions of the dependent parameters. This allows the user to determine the required statistics for each output parameter.
A number of analyses have been performed using the DORCA program for several NASA-funded Aerospace Corporation studies in the past few years. The data decks containing the input data for these analyses have been compiled and are submitted, under separate cover. A few of the data decks are full (basic) decks containing every data item and are used as reference decks in the data bank. The other data decks were obtained by differencing a full deck with respect to one of the reference decks. Using the DORMAN program, a full deck can be recreated from the modified deck and its reference deck when and if desired. The content and structure of the data bank are described. A description of each of these data decks is presented. Three of the cases that are included in this volume have become so widely recognized and accepted that additional descriptive material has been provided. The three cases are: Case 500 Costs, Case 506 Costs, and Case 403.
A listing is presented of the DORMAN program which was developed as a data bank management program for DORCA (Dynamic Operations Requirements and Cost Analysis) application.
Documentation of the NBODY trajectory optimization program is presented in the form of a mathematical development plus a user's manual. Optimal multistage-launch ascent trajectories may be determined by variational thrust steering during the upper phase. Optimal low-thrust interplanetary spacecraft trajectories may also be calculated with solar power or constant power, all-propulsion or embedded coast arcs, fixed or optimal thrust angles, and a variety of terminal end conditions. A hybrid iteration scheme solves the boundary-value problem, while either transversality conditions or a univariate search scheme optimize vehicle or trajectory parameters.
The design and evaluation are described of a digital turbojet engine control which is capable of sensing catastrophic failures in either the engine rotor speed or the compressor discharge static-pressure signal and is capable of switching control modes to maintain near normal operation. The control program was developed for and tested on a turbojet engine located in a sea-level test stand. The control program is also capable of acquiring all the data that are necessary for the fail-operational control to function.
A finite-difference program is described for calculating the viscous compressible boundary layer flow over either planar or axisymmetric surfaces. The flow may be initially laminar and progress through a transitional zone to fully turbulent flow, or it may remain laminar, depending on the imposed boundary conditions, laws of viscosity, and numerical solution of the momentum and energy equations. The flow may also be forced into a turbulent flow at a chosen spot by the data input. The input may contain the factors of arbitrary Reynolds number, free-stream Mach number, free-stream turbulence, wall heating or cooling, longitudinal wall curvature, wall suction or blowing, and wall roughness. The solution may start from an initial Falkner-Skan similarity profile, an approximate equilibrium turbulent profile, or an initial arbitrary input profile.
A general method developed for the analysis of inviscid hypersonic shock layers is discussed for application to the case of the shuttle vehicle at high (65 deg) angle of attack. The associated extensive subsonic flow region caused convergence difficulties whose resolution is discussed. It is required that the solution be smoother than anticipated.
REDUCE 2 is reported as a FORMAC program which symbolically calculates the transfer function(s) of any linear-block-diagram output variable to any or all input variables. The program requires as input a set of algebraic expressions representing the block diagram, the desired transfer function(s), and a string of variables indicating the desired order of reduction. The solution is presented in the compact form of a set of nested functions (super G's). The program can handle systems as large as 600 equations and is intended as a tool for the analysis of complex control and dynamic systems. A companion FORTRAN program, EVAL 2, which numerically evaluates the solution set to obtain amplitude ratio and phase angle as functions of frequency is also presented.
A computerized procedure developed for analyzing aerospace vehicles evaluates the properties of elemental surface areas with specified thickness by accumulating and combining them with arbitrarily specified mass elements to form a complete evaluation. Picture-like images of the geometric description are capable of being generated.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Program generates inlet contour maps with choice of mapping parameters. Contour maps are represented by symbols on picture produced by line printer. Program also generates variety of simple circumferential and radial distortion parameters that enable calculation of almost any specific distortion parameter.
Program evaluates influences of heat transfer, stress, and cycle life. Coolant passages may be tubes or channels, with or without gas-side wall coating. Program options include two-dimensional thermal analysis model of tube or channel cross-section using relaxation technique with variable number of nodes.