Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Anode material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Effect of non-solvent from the phase inversion method on the morphology and performance of the anode supported microtubular solid oxide fuel cells

The microstructure of the anode in anode-supported solid oxide fuel cells has significant influence on the cell performance. Here, microtubular Ni-yttria stabilized zircona (Zr 0.8 Y 0.2 O 2 , YSZ) anode support has been prepared by the phase inversion method. Different compositions of non-solvent have been used for the fabrication of the Ni-YSZ anode support, and the correlation between non-solvent composition and characteristics of the microstructure of the anode support has been investigated. The presence of ethanol or isopropanol in the non-solvent can inhibit the growth of the finger-like pores in the anode support. With the increase of the concentration of ethanol or isopropanol in the non-solvent, a thin dense layer can be observed on the top of the prepared tubular anode support. In addition, the mechanism of pore formation is explained based on the inter-diffusivity between the solvent and the non-solvent. Lastly, the prepared microtubular solid oxide fuel cells (MT-SOFCs) have been tested, and the influence of the anode microstructure on the cell electrochemical performance is analyzed based on a polarization model.

36 MATERIALS SCIENCE↗

Preparation of mesoporous titanium dioxide anode by a film- and pore-forming agent for the dye-sensitized solar cell

Highlights: • PVP is used as a film- and pore-forming agent to prepare the mesoporous TiO{sub 2} anode. • The TiO{sub 2} anode supplies high surface area for the dye adsorption. • The DSSC efficiency is strongly dependent on the pore properties of the TiO{sub 2} anode. • The DSSC efficiency with the TiO{sub 2} anode prepared by 20 wt% PVP reaches 8.39%. - Abstract: A novel mean of generating mesoporous titanium dioxide (TiO{sub 2}) anodes by employing polyvinylpyrrolidone (PVP) as the film- and pore-forming agent are proposed for dye-sensitized solar cells (DSSCs). The influences on the morphology and photovoltaic performances of the TiO{sub 2} anodes are investigated by adjusting the PVP content in synthesizing the mesoporous TiO{sub 2} anodes. The photovoltaic conversion efficiency of the DSSC is found to be strongly dependent on the pore properties of the TiO{sub 2} anode. After the sintering process, the removal of the PVP leaves porously interconnected channel structures inside the TiO{sub 2} anode, supplying enhanced specific surface area for the dye adsorption as well as the efficient electron transmission. As a result, the TiO{sub 2} anode prepared by 20 wt% PVP presents the highest performances, based on which the DSSC achieves the highest conversion efficiency of 8.39%, approximately increased by 56.53% than that of the DSSC fabricated without PVP (5.36%).

36 MATERIALS SCIENCE↗

High resolution neutron imaging of water in the polymer electrolyte membrane

To achieve a deeper understanding of water transport and performance issues associated with water management, we have conducted in situ water examinations to help understand the effects of components and operation. High Frequency Resistance (HFR), AC Impedance and neutron radiography were used to measure water content in operating fuel cells under various operating conditions. Variables examined include: sub-freezing conditions, inlet relative humidities, cell temperature, current density and response transients, different flow field orientations and different component materials (membranes, GDLs and MEAs). Quantification of the water within the membrane was made by neutron radiography after equilibration to different humidified gases, during fuel cell operation and in hydrogen pump mode. The water content was evaluated in bare Nafion{reg_sign} membranes as well as in MEAs operated in both fuel cell and H{sub 2} pump mode. These in situ imaging results allow measurement of the water content and gradients in the PEFC membrane and relate the membrane water transport characteristics to the fuel cell operation and performance under disparate materials and operational combinations. Flow geometry makes a large impact on MEA water content. Higher membrane water with counter flow was measured compared with co-flow for sub-saturated inlet RH's. This correlates to lower HFR and higher performance compared with co-flow. Higher anode stoichiometry helps remove water which accumulates in the anode channels and GDL material. Cell orientation was measured to affect both the water content and cell performance. While membrane water content was measured to be similar regardless of orientation, cells with the cathode on top show flooding and loss of performance compared with similarly operated cells with the anode on top. Transient fuel cell current measurements show a large degree of hysteresis in terms of membrane hydration as measured by HFR. Current step transients from 0.01 A cm{sup -2} to 0.68 A cm{sup -2} consistently show PEM wetting occurring within 5 to 20 sec. Whereas the PEM drying response to the reverse step transient of 0.68 A cm{sup -2} to 0.01 A cm{sup -2}, takes several minutes. The observed faster wetting response is due to reaction water being produced in the cathode and back diffusing into the membrane. The slower PEM drying is due to the water slowly being removed out of the wetted GDLs. This rate of removal of water and hence the PEM hydration level was found to be influenced strongly by the PTFE loadings in the GDL substrate and Microporous layer (MPL). The drying of the membrane is influenced by both the anode and cathode GDL PTFE loadings. Lower PTFE loading in the anode GDL leads to better membrane hydration probably due to the easier incorporation of water from the anode GDL into the membrane. Similarly a lower PTFE loading in the cathode GDL also results in better membrane hydration probably due to the better water retention properties (less hydrophobic) of this GDL. Fuel cells operated isothermal at sub-freezing temperatures show gradual cell performance decay over time and eventually drops to zero. AC impedance analysis indicates that losses are initially due to increasing charge transfer resistance. After time, the rate of decay accelerates rapidly due to mass transport limitations. High frequency resistance also increases over time and is a function of the initial membrane water content. These results indicate that catalyst layer ice formation is influenced strongly by the MEA and is responsible for the long-term degradation of fuel cells operated at sub-freezing temperatures. Water distribution measurements indicate that ice may be fonning mainly in the GDLs at -10 C but are concentrated in the catalyst layer at -20 C.

08 HYDROGEN↗

Exploring interfacial stability of solid-state electrolytes at the lithium-metal anode surface

Solid state electrolytes are promising materials to mitigate the issues derived from the extreme reactivity of the lithium metal anodes in Li-metal batteries. The main properties sought for this application are high ionic conductivity, low electronic conductivity, and high interfacial stability. Here we investigate a class of sulfides (Li 10 GeP 2 S 12 , Li2P2S6, β-Li 3 PS 4 , and Li 7 P 3 S 11 ) that have shown relatively good ionic conductivities. However, little is known regarding their interfacial stability. We use density functional theory and ab initio molecular dynamics simulations to investigate the time evolution of the interfacial structure. We characterize atomic diffusion and reactions happening at the picosecond time scale, allowing us to identify the main interfacial products: Li 2 S, Li 3 P and Li 17 Ge 4 . We then study how the reactivity changes when the Li metal surface is coated with a thin film of Li 2 S.

25 ENERGY STORAGE↗

Mechanistic Elucidation of Electronically Conductive PEDOT:PSS Tailored Binder for a Potassium‐Ion Battery Graphite Anode: Electrochemical, Mechanical, and Thermal Safety Aspects

Potassium-ion batteries (KIBs) are considered more appropriate for grid-scale storage than lithium-ion batteries (LIBs) due to similar operating chemistry, abundant precursors, and compatibility with low-cost graphite anodes. However, a larger ion reduces rate capabilities and exacerbates capacity fading from volumetric expansion. In this report, conductive polymer, poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS), is substituted for standard insulating polyvinylidene fluoride (PVDF). Half-cells using carbon black (CB) in continuously conductive PEDOT:PSS/CB binder outperforms PVDF/CB by mitigating electrically isolated “dead” graphite, improving 100 cycle capacity retention at C/10 from 63 to 80%. Enhanced electrical contact with PEDOT:PSS/CB also reduces ion impedance and improves rate capabilities. Without CB however, PEDOT:PSS binder performs poorly in electrochemical studies despite promising ex situ electronic conductivity. This discrepancy is mechanistically elucidated through identification of redox activity between PEDOT:PSS and K + which results in high impedances in the anode operating voltage window. Additionally, the impact of conducting binder on mechanical properties and thermal safety of the anode is investigated. Brittleness and poor wettability of PEDOT:PSS are identified as issues, but greater stability against reactive KC 8 reduces overall heat generation. Binder substitution offers a promising means of mitigating issues with current KIB anodes regardless of active material, and the work herein addresses issues towards further improvement.

electrochemical impedance spectroscopy↗

Effects of Surface Oxygen on the Performance of Carbon as an Anode in Lithium-Ion Batteries

Carbon materials with similar bulk structure but different surface oxygen were compared for their performance as anodes in lithium-ion battery. The bulk structure was such that the graphene planes were perpendicular to the surface. Three types of surfaces were examined: surface containing C=O type oxygen. surface containing -O-C type oxygen, and surface containing high concentration of active sites. The test involved cycles of lithium insertion into and release from the carbon materials, which was in the half cells of carbon/saturated LiI-50/50 (vol %) EC and DMC/lithium. During the first cycle of lithium insertion, the presence of adsorbed oxygen, -O-C type oxygen, active carbon sites, and C=O type oxygen resulted in the formation of solid-electrolyte interface (SEI) when the carbon's voltage relative to lithium metal was >1.35, 1 to 1.35, 0.5 to 1, and 0.67 to 0.7 V, respectively. An optimum -O-C type oxygen and a minimum C=O type oxygen was found to increase the reversible and decrease the irreversible capacity of carbon. Active sites on the carbon surface result in a large irreversible capacity and a second lithium insertion-release mechanism. However, this new mechanism has a short cycle life.

Hung, Ching-Cheh↗

Analysis of the electric field induced elemental separation of Ge{sub 2}Sb{sub 2}Te{sub 5} by transmission electron microscopy

The chemical instability of line patterned Ge{sub 2}Sb{sub 2}Te{sub 5} was studied by transmission electron microscopy after electrically inducing melt and solidification. Compositional analysis showed elemental separation of Te to the anode side, while Ge and Sb mutually separated at the cathode side. Such elemental separation of Ge{sub 2}Sb{sub 2}Te{sub 5} is explained by the electric field effects and thermodynamic driving forces.

36 MATERIALS SCIENCE↗

Corrosion of 907 Steel Influenced by Sulfate-Reducing Bacteria

The effect of sulfate-reducing bacteria (SRB) on the corrosion of 907 steel was investigated. Results demonstrated that the chemical composition of corrosion products, the corrosion rate, and corrosion type were altered due to the adherence of SRB and the subsequent formation of biofilm on the 907 steel surface. Different from the case in sterile medium that ferrous oxides predominated in the corrosion products, ferrous sulfide was an important component in SRB-containing medium. Meanwhile, corrosion of 907 steel was enhanced by SRB, and the corrosion rate was dependent on their metabolic activity, which increased, stabilized, and decreased in the exponential growth, death, and residual phases, respectively. Furthermore, the corrosion type was changed from uniform corrosion to localized corrosion with the introduction of SRB, and the development process was analyzed based on the current distribution map of wire beam electrodes. In sterile medium, the maximum current density decreased with the immersion time extended, and there were no significant anodic current peaks in the late period, while in SRB-containing medium, the ratio between cathodic areas and anodic areas was high in the exponential growth phase, and stable anodic sites formed gradually in death and residual phases, which facilitated the development of localized corrosion.

36 MATERIALS SCIENCE↗

Mechanical Properties and Chemical Reactivity of Li x SiO y Thin Films

Silicon (Si) is a commonly studied candidate material for next-generation anodes in Li-ion batteries. A native oxide SiO 2 on Si is often inevitable. However, it is not clear if this layer has a positive or negative effect on the battery performance. This understanding is complicated by the lack of knowledge about the physical properties of the SiO 2 lithiation products and by the convolution of chemical and electrochemical effects during the anode lithiation process. In this study, Li x SiO y thin films as model materials for lithiated SiO 2 were deposited by magnetron sputtering at ambient temperature, with the goal of (1) decoupling chemical reactivity from electrochemical reactivity and (2) evaluating the physical and electrochemical properties of Li x SiO y . X-ray photoemission spectroscopy analysis of the deposited thin films demonstrate that a composition close to previous experimental reports of lithiated native SiO 2 can be achieved through sputtering. Our density functional theory calculations also confirm that the possible phases formed by lithiating SiO 2 are very close to the measured film compositions. Scanning probe microscopy measurements show that the mechanical properties of the film are strongly dependent on lithium concentration, with a ductile behavior at a higher Li content and a brittle behavior at a lower Li content. The chemical reactivity of the thin films was investigated by measuring the AC impedance evolution, suggesting that Li x SiO y continuously reacts with the electrolyte, in part because of the high electronic conductivity of the film determined from solid-state impedance measurements. The electrochemical cycling data of the sputter-deposited Li x SiO y /Si films also suggest that Li x SiO y is not beneficial in stabilizing the Si anode surface during battery operation, despite its favorable mechanical properties.

14 SOLAR ENERGY↗

Porosity-dependent fractal nature of the porous silicon surface

Porous silicon films with porosity ranging from 42% to 77% were fabricated by electrochemical anodization under different current density. We used atomic force microscopy and dynamic scaling theory for deriving the surface roughness profile and processing the topography of the porous silicon layers, respectively. We first compared the topography of bare silicon surface with porous silicon and then studied the effect of the porosity of porous silicon films on their scaling behavior by using their self-affinity nature. Our work demonstrated that silicon compared to the porous silicon films has the highest Hurst parameter, indicating that the formation of porous layer due to the anodization etching of silicon surface leads to an increase of its roughness. Fractal analysis revealed that the evolution of the nanocrystallites’ fractal dimension along with porosity. Also, we found that both interface width and Hurst parameter are affected by the increase of porosity.

36 MATERIALS SCIENCE↗

Electrosynthesis of Ti{sub 5}Si{sub 3}, Ti{sub 5}Si{sub 3}/TiC, and Ti{sub 5}Si{sub 3}/Ti{sub 3}SiC{sub 2} from Ti-Bearing Blast Furnace Slag in Molten CaCl{sub 2}

Ti{sub 5}Si{sub 3}, Ti{sub 5}Si{sub 3}/TiC, and Ti{sub 5}Si{sub 3}/Ti{sub 3}SiC{sub 2} have been electrochemically synthesized from the Ti-bearing blast furnace slag/TiO{sub 2} and/or C mixture precursors at a cell voltage of 3.8 V and 1223 K to 1273 K (950 °C to 1000 °C) in molten CaCl{sub 2}. The pressed porous mixture pellets were used as the cathode, and a solid oxide oxygen-ion-conducting membrane (SOM)-based anode was used as the anode. The phase composition and morphologies of the cathodic products were systematically characterized. The final products possess a porous nodular microstructure due to the interconnection of particles. The variations of impurity elements, i.e., Ca, Mg, and Al, have been analyzed, and the result shows that Ca and Mg can be almost completely removed; however, Al cannot be easily removed from the pellet due to the formation of Ti-Al alloys during the electroreduction process. The electroreduction process has also been investigated by the layer-depended phase composition analysis of the dipped/partially reduced pellets to understand the detailed reaction process. The results indicate that the electroreduction process of the Ti-bearing blast furnace slag/TiO{sub 2} and/or C mixture precursors can be typically divided into four periods, i.e., (i) the decomposition of initial Ca(Mg,Al)(Si,Al){sub 2}O{sub 6}, (ii) the reduction of Ti/Si-containing intermediate phases, (iii) the removal of impurity elements, and (iv) the formation of Ti{sub 5}Si{sub 3}, TiC, and Ti{sub 3}SiC{sub 2}. It is suggested that the SOM-based anode process has great potential to be used for the direct and facile preparation of Ti alloys and composites from cheap Ti-containing ores.

36 MATERIALS SCIENCE↗

Effect of anodization parameters on the structural morphology of titanium in fluoride containing electrolytes

In the present work, formation of titania nanopores on titanium substrate was investigated in aqueous (sulphuric acid) and neutral organic (glycerol) electrolytes containing different concentrations of HF (0.1-0.2 M). The surface morphology, topography and phase structures were analyzed using scanning electron microscopy, atomic force microscopy and X-ray diffraction techniques, respectively. Under optimized electrolyte conditions, titania nanopore is obtained with the average pore diameter of 64 nm and 84 nm for aqueous and organic electrolytes, respectively. Atomic force microscope investigation shows that the porous layer forms under a competition of titania formation and oxide dissolution up to a limiting thickness of {approx} 75 nm and 100 nm respectively for aqueous and organic electrolytes. The porous structure was observed at 0.15 M HF concentration. It was found that depending on the electrolytes the pore diameter alters and also its concentration effected the porous structures formation. Compared to aqueous electrolytes, organic electrolytes showed larger diameter pores. From the X-ray diffraction measurement it is evident that the as prepared titania nanopores are amorphous in nature, whereas the anodized heat treated titania nanopores are in anatase phase. - Highlights: Black-Right-Pointing-Pointer Aqueous and organic electrolytes were used to synthesize nanoporous titania. Black-Right-Pointing-Pointer The surface morphology varies with various concentrations of HF. Black-Right-Pointing-Pointer Nanopores were formed at optimum HF concentration of 0.15 M. Black-Right-Pointing-Pointer Nanopore diameter was found to be affected by the electrolyte used.

36 MATERIALS SCIENCE↗

High Voltage Operation of Ni-Rich NMC Cathodes Enabled by Stable Electrode/Electrolyte Interphases

Lithium (Li) metal battery (LMB) is one of the most promising candidates for the next generation energy storage systems. However, it is still a significant challenge to operate LMBs with high voltage cathode under high rate conditions. In this work, a LMB using nickel-rich layered cathode of LiNi0.76Mn0.14Co0.10O2 (NMC76) and an optimized electrolyte (0.6 M LiTFSI + 0.4 M LiBOB + 0.05 M LiPF6 dissolved in EC: EMC (4:6 by weight)) demonstrate excellent stability under a high charge cutoff voltage of 4.5 V. Remarkably, these Li||NMC76 cells can deliver a high discharge capacity of > 220 mAh g-1 (846 Wh kg-1) and retain more than 80% capacity after 1000 cycles under a high charge/discharge current rates of 2C/2C (1C = 200 mA g-1). These excellent electrochemical performances can be attributed to the highly enhanced structural/interfacial stability of both Ni-rich NMC76 cathode materials and Li metal anode using the optimized electrolyte.

Ni-rich NMC, cathode electrolyte interphase, dual ↗

Microstructure degradation of YSZ in Ni/YSZ anodes of SOFC operated in phosphine-containing fuels

The interaction of trace (ppm) phosphine with the nickel/yttria stabilized zirconia (YSZ) anode of commercial solid oxide fuel cells has been investigated and evaluated for both synthesis gas and hydrogen fuels in an effort to examine P–Y reactions. The Ni poisoning effects reported in literature were confirmed and degradation was examined by electrochemical methods and post-test microstructural and chemical analyses. The results indicate that P-induced degradation rates and mechanisms are fuel dependent and that degradation of cells operated in synthesis gas (syngas) with phosphine is more severe than that of cells operated in hydrogen with phosphine. As reported in published literature, a cell operated in syngas containing 10 ppm phosphine demonstrated significant microstructural degradation within the Ni phase, including formation of Ni–P phases concentrated on the outer layer of the anode and significant pitting corrosion in the Ni grains. In this research, a previously undetected YPO{sub 4} phase is observed at the YSZ/YSZ/Ni triple grain junctions located at the interface with the YSZ electrolyte. Tetragonal YSZ (t-YSZ) and cubic-YSZ (c-YSZ) domains with sizes of several tens of nanometers are also newly observed along the Ni/YSZ interface. These observations contrast with data obtained for a cell operated in dry hydrogen with phosphine, where no YPO{sub 4} phase is observed and the alternating t-YSZ and c-YSZ domains at the Ni/YSZ interface are smaller with typical sizes of 5–10 nm. The data imply that electrolyte attack by P is a potentially debilitating mode of degradation in SOFC anodes, and that the associated reaction mechanisms and rates are worthy of further examination.

30 DIRECT ENERGY CONVERSION↗

Effects of sulfur loading on the corrosion behaviors of metal lithium anode in lithium–sulfur batteries

Highlights: • The effects of sulfur loading on the corrosion behaviors were investigated systematically. • The corrosion became severer with increasing sulfur loading or cycle times. • The corrosion films are porous and loose and cannot prevent further reaction between lithium and polysulfides. - Abstract: The corrosion behaviors in rechargeable lithium–sulfur batteries come from the reactions between polysulfides and metal lithium anode, and they are significantly influenced by the sulfur loading. While there are limited papers reported on the effects of sulfur loading on the corrosion behaviors. In this paper, the effects have been investigated systematically. The corrosion films consisted of insulating lithium ion conductors are loose and porous, so that the corrosive reactions cannot be hindered. The thickness of the corrosion layers, consequently, increased along with increasing sulfur loading or cycle times. For instance, the thickness of corrosion layers after 50 cycles was 98 μm in the cell with 5 mg sulfur while it reached up to 518 μm when the loading increased to 15 mg. The continuous deposition of corrosion products gave rise to low active materials utilization and poor cycling performance.

36 MATERIALS SCIENCE↗

Development of large area transparent conducting oxides from a combinatorial lead for organic solid state lighting

Organic light emitting device (OLEDs) may provide a low-cost, long-lived, and efficient wide area lighting solution if a number of challenges in reliability, cost and efficiency can be overcome. There is a need to develop new TCOs for use as the anode in a bottom-emitting device that do not contain In, have optimal work function, conductivity and visible light transmission properties, possess acceptable stability and possess a high work function to match the deep HOMO of blue OLED HTLs. We report here results from our efforts to scale up sputter deposition on large area substrates (up to 12”x12”) of TCO candidates (including Ga:ZnO and Zn:SnO) identified using combinatorial methods. We present transmission, electrical properties, work function, compositional and structural data for these films. Finally, we have evaluated the use of these materials in OLEDs, and show device performance comparisons between devices fabricated on combinatorial substrates, single composition substrates, and substrates grown at larger scale (up to 12”x12”). Post-operation analysis of the materials using a combination of surface analysis and electron microscopy techniques was performed. The device results demonstrate that we are able to generate substrates with the appropriate work function to reduce the operating voltage of blue phosphorescent OLEDs compared to commercial ITO, which we ascribe to improved work function-HOMO energy matching leading to more efficient charge injection into the device HTL.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗