Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Advanced Modeling and Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Coupled loads analysis of a novel shared-mooring floating wind farm

Shared mooring lines are a method to reduce the stationkeeping cost of floating offshore wind farms; however, their impacts on floating array dynamics are not yet well understood. Here this article presents advancements to floating wind farm simulation capabilities that allow the dynamic modeling of shared-mooring floating wind arrays - specifically, platform coupling through shared lines and proper phasing of wave loads across the array. These capabilities are demonstrated on a 10-turbine shared-mooring array featuring two staggered rows of wind turbines. A baseline array design with individually moored turbines is used as a basis for comparison. Coupled analysis using FAST.Farm shows that the shared-mooring design has smaller fluctuations in surge when compared to the baseline design. The mean and maximum platform offsets are highest in normal operating conditions, but the maximum mooring line tensions are highest in 50-year storm conditions. Power spectral density analysis of platform surge and sway motions shows that the shared mooring configuration does not introduce any significant inter-platform resonances. The tower-base bending moment statistics and the line tension damage equivalent loads indicate no consequential differences in turbine loading or mooring fatigue life. Anchor load analysis shows that the total required anchor capacity for the shared-mooring array is decreased by approximately 25% when shared anchors are used. Dynamic simulations of the shared mooring system under line failures show that remaining line tensions stay within bounds and that offsets are significantly smaller when compared to the baseline design. Overall, the results show that shared moorings do not introduce any dynamic response concerns in this floating wind array design.

17 WIND ENERGY↗
DOE OSTI2024

Impact of anisotropy on TRISO fuel performance

Manufacturing of tristructural isotropic (TRISO) particles involves the deposition of pyrolytic carbon (PyC) and silicon carbide (SiC) layers using the fluidized bed chemical vapor deposition (CVD) process. The CVD process is known to generate polycrystalline layers with crystallographic textures, which imparts anisotropic thermophysical properties to the layers. Past studies have shown the risk for particle failure increases with an increase in anisotropy. The limit beyond which the anisotropy of PyC layers becomes unacceptable due to failure risk has been identified as a high-priority knowledge gap. This work presents a first systematic study on the effects of anisotropic thermal and mechanical properties on TRISO fuel performance. This computational study, performed using the fuel performance code BISON, investigates how the anisotropy in elasticity and thermal properties affect the stresses, temperature, and failure of a TRISO particle. The influence of other factors, such as operating temperature and particle geometry on the anisotropy effects, also has been analyzed. The studies utilize the recently published anisotropic elasticity and thermal behavior models for TRISO PyC and SiC layers implemented using tensors with full anisotropic capability. The spherical TRISO particles with anisotropic properties were found to have greater maximum tensile stress and significantly higher failure probability than the spherical particles with isotropic properties. In conclusion, the fuel performance predicted using these recently developed models was found to be comparable with the performance obtained using the historical models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Electromagnetic Transient (EMT) Simulation Algorithm for Evaluation of Photovoltaic (PV) Generation Systems

Use of inverter-based resources facilitating renewable energy resources such as photovoltaic (PV) generation is increasing rapidly with decreasing costs and reduced emissions associated. To accommodate such rapid growth of inverter-based resources like PV systems, electromagnetic transient (EMT) simulation models of both PV systems and grids are required to analyze the interaction of PVs in the grid (like the post-event analysis). In addition, the EMT simulation would help with the planning of future power grid with a large number of PVs as well as other inverter-based distributed generation systems. In this paper, the EMT simulation models of PV systems and grids are developed based on the differential algebraic equations (DAEs) representing their EMT dynamics. Furthermore, advanced simulation algorithms including numerical stiffness-based hybrid discretization, DAE clustering and aggregation, multi-order integration, and matrix splitting approaches are applied to accelerate the EMT simulation. The proposed algorithm was applied to 125 PV inverters within 52-bus medium-voltage (MV) distribution grid.

Choi, Jongchan↗
DOE OSTI2020

Fast-Spectrum Critical Assemblies with a Pb-HEU Core Surrounded by a Copper Reflector

The Department of Energy invests tens of millions of dollars each year to develop the next generation of nuclear engineering modeling & simulation (M&S) tools. These M&S tools are used to analyze advanced reactor designs and the safety of current nuclear operations. As computers become more powerful, we are able to enhance resolution in our calculations. This improved resolution is taking us to a point where the limitations of simulation capability are in the quality of data, including our ability to quantify the uncertainty and sensitivity of the data. In order to accurately model systems of interest, the industry must improve key nuclear data measurements and our confidence of how well we understand the data. Thus, M&S tools need evaluated and quality-assured experimental data for validation purposes. The International Criticality Safety Benchmark Evaluation Project (ICSBEP) compiles benchmark experiment data in a handbook that can be used by criticality safety engineers to validate computer codes and cross-section libraries at nuclear facilities. Both critical and subcritical experiments are included in the handbook. Figure 1 organizes all the benchmark evaluations that have been performed by the isotope of interest, in this case Pb, and the neutron energy within the system. Compared to other isotopes of interest for nuclear applications, there are few benchmark evaluations for Pb systems. This has caused the latest nuclear cross-section libraries to over/underestimate changes in the neutron population compared to experimental results. Therefore, this evaluation fills an important knowledge gap in benchmark evaluations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

AI for Science: Report on the Department of Energy (DOE) Town Halls on Artificial Intelligence (AI) for Science

The report documents the DOE Town Halls held during 2019 at Argonne National Laboratory, Oak Ridge National Laboratory, Lawrence Berkeley National Laboratory, and in Washington, DC. From July to October 2019, the Argonne, Oak Ridge, and Berkeley National Laboratories hosted a series of four town hall meetings attended by more than 1,000 U.S. scientists and engineers. The goal of the town hall series was to examine scientific opportunities in the areas of artificial intelligence (AI), Big Data, and high-performance computing (HPC) in the next decade, and to capture the big ideas, grand challenges, and next steps to realizing these opportunities. In this report and in the Department of Energy (DOE) laboratory community, we use the term “AI for Science” to broadly represent the next generation of methods and scientific opportunities in computing, including the development and application of AI methods (e.g., machine learning, deep learning, statistical methods, data analytics, automated control, and related areas) to build models from data and to use these models alone or in conjunction with simulation and scalable computing to advance scientific research. The AI for Science town hall discussions focused on capturing the transformational uses of AI that employ HPC and/or data analysis, leveraging data sets from HPC simulations or instruments and user facilities, and addressing scientific challenges unique to DOE user facilities and the agency’s wide-ranging fundamental and applied science enterprise.

36 MATERIALS SCIENCE↗
DOE OSTI2021

NEAMS TH CRAB

The MOOSE framework is a library designed to make it straightforward for physicists and engineers to model partial differential equations using finite element and finite volume methods. Finite elements have been a part of the framework library since MOOSE's inception over a decade ago. Initial finite volume capability, however, was added only as recently as May of 2020. Since that time, significant work has been conducted to develop fluid modeling capability based on the finite volume method. Much of this work has taken place in MOOSE's navier_stokes module and in the NEAMS program's coarse mesh CFD code Pronghorn. We report here on development in MOOSE and Pronghorn of incompressible, porous incompressible, and weakly compressible finite volume simulation capabilities and their application to modeling of MSR and FHR advanced reactor concepts.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

TSL Nuclear Fuel Evaluations and Capabilities at NC State University [Slides]

This presentation discusses the purpose of this project which is to provide thermal scattering law (TSL) and cross section data to support advanced reactor modeling and criticality safety. The presentation also examines modeling and simulations, evaluation updates, and benchmark applications in connection with the project. In summation, new and updated uranium fuel evaluations have been submitted to the ENDF/B libraries. These include vital fuel materials U-metal, UC, UN, and UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1976

Preliminary simulation of an advanced, hingless rotor XV-15 tilt-rotor aircraft

The feasibility of the tilt-rotor concept was verified through investigation of the performance, stability and handling qualities of the XV-15 tilt rotor. The rotors were replaced by advanced-technology fiberglass/composite hingless rotors of larger diameter, combined with an advanced integrated fly-by-wire control system. A parametric simulation model of the HRXV-15 was developed, model was used to define acceptable preliminary ranges of primary and secondary control schedules as functions of the flight parameters, to evaluate performance, flying qualities and structural loads, and to have a Boeing-Vertol pilot conduct a simulated flight test evaluation of the aircraft.

Mcveigh, M. A.↗
NASA NTRS1989

Proceedings of the 3rd Annual Conference on Aerospace Computational Control, volume 1

Conference topics included definition of tool requirements, advanced multibody component representation descriptions, model reduction, parallel computation, real time simulation, control design and analysis software, user interface issues, testing and verification, and applications to spacecraft, robotics, and aircraft.

Bernard, Douglas E.↗
NASA NTRS2003

Current Developments in Future Planetary Probe Sensors for TPS

In-situ Thermal Protection System (TPS) sensors are required to provide traceability of TPS performance and sizing tools. Traceability will lead to higher fidelity design tools, which in turn will lead to lower design safety margins, and decreased heatshield mass. Decreasing TPS mass will enable certain missions that are not otherwise feasible, and directly increase science payload. NASA Ames is currently developing two flight measurements as essential to advancing the state of TPS traceability for material modeling and aerothermal simulation: heat flux and surface recession (for ablators). The heat flux gage is applicable to both ablators and non-ablators and is therefore the more generalized sensor concept of the two with wider applicability to mission scenarios. This paper describes the development of a microsensor capable of surface and in-depth temperature and heat flux measurements for TPS materials appropriate to Titan, Neptune, and Mars aerocapture, and direct entry. The thermal sensor will be monolithic solid state devices composed of thick film platinum RTD on an alumina substrate. Choice of materials and critical dimensions are used to tailor gage response, determined during calibration activities, to specific (forebody vs. aftbody) heating environments. Current design has maximum operating temperature of 1500 K, and allowable constant heat flux of q=28.7 watts per square centimeter, and time constants between 0.05 and 0.2 seconds. The catalytic and radiative response of these heat flux gages can also be changed through the use of appropriate coatings. By using several co-located gages with various surface coatings, data can be obtained to isolate surface heat flux components due to radiation, catalycity and convection. Selectivity to radiative heat flux is a useful feature even for an in-depth gage, as radiative transport may be a significant heat transport mechanism for porous TPS materials in Titan aerocapture. This paper also reports on progress to adapt a previously flown surface recession sensor, based on the Jupiter probe Galileo Analog Resistance Ablation Detector (ARAD), to appropriate aerocapture conditions.

Martinez, Ed↗
NASA NTRS2005

Development of Solid State Thermal Sensors for Aeroshell TPS Flight Applications

In-situ Thermal Protection System (TPS) sensors are required to provide verification by traceability of TPS performance and sizing tools. Traceability will lead to higher fidelity design tools, which in turn will lead to lower design safety margins, and decreased heatshield mass. Decreasing TPS mass will enable certain missions that are not otherwise feasible, and directly increase science payload. NASA Ames is currently developing two flight measurements as essential to advancing the state of TPS traceability for material modeling and aerothermal simulation: heat flux and surface recession (for ablators). The heat flux gage is applicable to both ablators and non-ablators and is therefore the more generalized sensor concept of the two with wider applicability to mission scenarios. This paper describes the continuing development of a thermal microsensor capable of surface and in-depth temperature and heat flux measurements for TPS materials appropriate to Titan, Neptune, and Mars aerocapture, and direct entry. The thermal sensor is a monolithic solid state device composed of thick film platinum RTD on an alumina substrate. Choice of materials and critical dimensions are used to tailor gage response, determined during calibration activities, to specific (forebody vs. aftbody) heating environments. Current design has maximum operating temperature of 1500K, and allowable constant heat flux of q=28.7 W/cm(sup 2), and time constants between 0.05 and 0.2 seconds. The catalytic and radiative response of these heat flux gages can also be changed through the use of appropriate coatings. By using several co-located gages with various surface coatings, data can be obtained to isolate surface heat flux components due to radiation, catalycity and convection. Selectivity to radiative heat flux is a useful feature even for an in-depth gage, as radiative transport may be a significant heat transport mechanism for porous TPS materials in Titan aerocapture.

Martinez, Ed↗
NASA NTRS2016

Accurately Characterizing the Importance of Wave-Particle Interactions in Radiation Belt Dynamics: The Pitfalls of Statistical Wave Representations

Wave-particle interactions play a crucial role in energetic particle dynamics in the Earths radiation belts. However, the relative importance of different wave modes in these dynamics is poorly understood. Typically, this is assessed during geomagnetic storms using statistically averaged empirical wave models as a function of geomagnetic activity in advanced radiation belt simulations. However, statistical averages poorly characterize extreme events such as geomagnetic storms in that storm-time ultralow frequency wave power is typically larger than that derived over a solar cycle and Kp is a poor proxy for storm-time wave power.

Murphy, Kyle R.↗
DOE OSTI2021

BISON As-run AGR-3/4 Irradiation Test Predictions

BISON, a nuclear fuel performance application built using the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element library, was used to model the Advanced Gas Reactor (AGR)-3/4 irradiation test using as-run physics and thermal hydraulics data. The AGR-3/4 test consists of the combined third and fourth planned irradiations of the AGR Fuel Development and Qualification Program. The AGR-3/4 test train consists of twelve separate and independently controlled and monitored capsules. Each capsule contains four compacts filled with both uranium oxycarbide (UCO) unaltered “driver” fuel particles and UCO designed-to-fail (DTF) fuel particles. The DTF fraction was specified to be 1×10-2. This report documents the calculations performed to predict the failure probability of tristructural isotropic (TRISO) coated driver fuel particles during the AGR-3/4 experiment on a single compact. This report will demonstrate the capabilities of BISON to model the complex AGR-3/4 irradiation test and identify further development needed to capture the fuel particle failure probability and source term on every compact for further comparison from post-irradiation examination (PIE) data. The calculations include the modeling of the AGR-3/4 irradiation that occurred from December 2011 to April 2014 in the Advanced Test Reactor (ATR) over a total of 10 ATR cycles including seven normal cycles, one low power cycle, one unplanned outage cycle, and one Power Axial Locator Mechanism (PALM) cycle.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Framework for Optimization, Quantification of Uncertainty and Surrogates – Updated Capabilities

This poster presents updated capabilities within the FOQUS Toolset, covering core features as well as project-based applications. Specifically, the poster highlights advancements in FOQUS integration with cloud-based clients, plugin support for machine learning tools and external simulations, sequential design of experiments, and advanced support for dynamic process models. The applications demonstrate the breadth of FOQUS predictive capabilities for chemical, energy and economic system analysis.

Paul, Brandon↗
DOE OSTI2025

PSA 2025 Presentation: "Modeling and Sensitivity Analysis of a Generation IV Pebble Bed Reactor Using MELCOR 2.2"

Accompanying the advancement of reactor technologies is the need for computational modeling and simulation to predict their behavior under normal operating conditions and accident scenarios. New Generation IV reactor designs which employ non-conventional fuel have a particular need for modeling the behavior and release of radionuclides and other material from the fuel. In this work, MELCOR version 2.2, a system-level safety and accident scenario code developed by Sandia National Laboratories, was used to model a 200-MWth pebble bed modular reactor and calculate the inventories of circulating and deposited graphite, metal dust, and elemental components released from the fuel elements. A base case modeling the reactor under standard operating conditions was calculated using MELCOR and the inventories were extrapolated to 30 years of operation time using a logarithmic regression fit. A sensitivity analysis was also performed in which several key parameters for the base case model were modified to explore the effect of these changes on the inventories calculated by MELCOR. A set of transient scenario simulations for a depressurized loss of forced cooling (DLOFC) accident were also performed. The results of the sensitivity analysis and transient simulations are reported and discussed in relation to the modeling techniques used for this study.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Interactions Between Climate Policy and Technology-influenced Travel Behavior: Mitigating Induced Demand from CACC

Advances in vehicle technology have influenced the development of automated vehicle systems, where vehicles that do not require human intervention are already deployed in the roadway networks. While these advances are proved to increase roadway safety and highway capacity, more research is needed to understand the long-term and regional-level impacts on mobility, land use, energy consumption, and emissions. This study proposes a multi-model approach to analyze the effect of vehicle automation and deep decarbonization policies over a period from 2020 to 2040 in Austin, Texas. We use the Global Change Analysis Model (GCAM) to develop internally the scenarios that are then passed to the SMART Mobility modeling workflow, a large-scale simulation framework combining the POLARIS activity-based travel demand model and mesoscopic traffic simulator with the Autonomie vehicle energy consumption model and the UrbanSim land use simulator. Results suggest that the introduction of vehicles with advanced automation could increase fuel consumption when no decarbonization policies are implemented. Also, advances in vehicle technology research and development could lead to a decline in energy use in the long-term. Energy pricing and vehicle electrification incentives could help reduce the impact of vehicle automation. Finally, our analysis indicates the relevance of introducing land use processes in longterm vehicle automation studies.

land use↗
DOE OSTI2017

Derivation of aerosol profiles for MC3E convection studies and use in simulations of the 20 May squall line case

Advancing understanding of deep convection microphysics via mesoscale modeling studies of well-observed case studies requires observation-based aerosol inputs. Here, we derive hygroscopic aerosol size distribution input profiles from ground-based and airborne measurements for six convection case studies observed during the Midlatitude Continental Convective Cloud Experiment (MC3E) over Oklahoma. We demonstrate use of an input profile in simulations of the only well-observed case study that produced extensive stratiform outflow on 20 May 2011. At well-sampled elevations between -11 and -23 °C over widespread stratiform rain, ice crystal number concentrations are consistently dominated by a single mode near ~400 µm in randomly oriented maximum dimension ( D max ). The ice mass at -23 °C is primarily in a closely collocated mode, whereas a mass mode near D max ~1000 µm becomes dominant with decreasing elevation to the -11 °C level, consistent with possible aggregation during sedimentation. However, simulations with and without observation-based aerosol inputs systematically overpredict mass peak D max by a factor of 3–5 and underpredict ice number concentration by a factor of 4–10. Previously reported simulations with both two-moment and size-resolved microphysics have shown biases of a similar nature. The observed ice properties are notably similar to those reported from recent tropical measurements. Based on several lines of evidence, we speculate that updraft microphysical pathways determining outflow properties in the 20 May case are similar to a tropical regime, likely associated with warm-temperature ice multiplication that is not well understood or well represented in models.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2017

Derivation of Aerosol Profiles for MC3E Convection Studies and Use in Simulations of the 20 May Squall Line Case

Advancing understanding of deep convection microphysics via mesoscale modeling studies of well-observed case studies requires observation-based aerosol inputs. Here, we derive hygroscopic aerosol size distribution input profiles from ground-based and airborne measurements for six convection case studies observed during the Midlatitude Continental Convective Cloud Experiment (MC3E) over Oklahoma. We demonstrate use of an input profile in simulations of the only well-observed case study that produced extensive stratiform outflow on 20 May 2011. At well-sampled elevations between −11 and −23 C over widespread stratiform rain, ice crystal number concentrations are consistently dominated by a single mode near approx. 400 microm in randomly oriented maximum dimension (Dmax). The ice mass at −23 C is primarily in a closely collocated mode, whereas a mass mode near Dmax approx. 1000 microns becomes dominant with decreasing elevation to the −11 C level, consistent with possible aggregation during sedimentation. However, simulations with and without observation-based aerosol inputs systematically overpredict mass peak Dmax by a factor of 3-5 and underpredict ice number concentration by a factor of 4-10. Previously reported simulations with both two-moment and size-resolved microphysics have shown biases of a similar nature. The observed ice properties are notably similar to those reported from recent tropical measurements. Based on several lines of evidence, we speculate that updraft microphysical pathways determining outflow properties in the 20 May case are similar to a tropical regime, likely associated with warm-temperature ice multiplication that is not well understood or well represented in models.

Fridlind, Ann M.↗