Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ATTITUDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Damping enhancement and attitude control of large space structures

Enhancement of modal damping in large space structures (LSS) is highly desirable and sometimes essential for the stability of the primary attitude control system. This paper considers the use of a number of Annular Momentum Control Devices (AMCD's) for damping enhancement in LSS. It is proved that the closed-loop system is stable in the sense of Lyapunov. Sufficient conditions for asymptotic stability are also obtained.

Joshi, S. M.↗

Attitude and translation control of a low-altitude Gravsat

Dynamic simulation of the Gravsat's attitude and translation control system is used to provide an upper bound for the fuel supply and test the feasibility of the preliminary design. A preliminary design is made for the disturbance compensation system (DISCOS) sensor, the thruster control laws, reaction wheel control laws, and the onboard state estimators. The sensor analysis and noise measurements show no problems in scaling the Triad navigation satellite sensor design up to meet the Gravsat requirements, except for proof mass center-of-mass offset. A promising technique is proposed to measure and eliminate this error. The covariance analysis confirms that a sophisticated post-flight data fit will be necessary to reconstruct a scientifically useful proof mass state. The DISCOS sensor will have to be continuously calibrated from the inflight data to achieve this reconstruction.

Ray, J. C.↗

Development of the Galileo Attitude and Articulation Control Subsystem flight software

The ongoing design and implementation of the Project Galileo Attitude and Articulation Control Subsystem (AACS) flight software is outlined, as well as the more important problems that were experienced in the development of this software. The important characteristics of the Galileo spacecraft are described, as are the major requirements driving the software design. The important features of the design are stated and discussed, and a modes and tasks transition diagram is presented. The AACS software implementation is covered, and the algorithms active in each task are shown. Finally, some of the design and management techniques used in the course of the software development are discussed.

Krasner, S. M.↗

A jet controlled magnetic referenced attitude control system for spinning payloads

An attitude control system was designed permitting large angle acquisition and alignment of the principle axis of a spinning payload to within 1 degree of the earth's magnetic field. Signals from magnetometer and gyro sensors are fed to the control algorithm to generate commands for the jet thrusters. The algorithm contains a cross axis magnetometer signal to prevent a large angle magnetometer signal to prevent a large angle equilibrium solution. The acquisition will occur within 50 seconds from initial precession and nutation angles of 30 degrees. An electronic spin filter passes signals at spin and nutation frequencies and rejects bias signals due to sensor misalignment and principle axis offset. Describing function analysis and total analog simulation techniques were used. The flight ACS hardware was interfaced with the analog computer simulation for design and verification. The controller has flown on four successful missions.

Celmer, J. J.↗

STRAP V - Higher accuracy, lower drift attitude control system

The STRAP V system was developed to provide higher accuracy and lower limit cycle fine pointing (+ or - 7 arcseconds) in all three axes at targets which cannot be tracked by startrackers or solar trackers. The system provides an increase in pointing performance over that obtainable with the STRAP IV (1) Attitude Control System (ACS). The STRAP IV concept of third axis updates is utilized to reduce pointing errors, using the flight-proven STRAP III (2) system as a first stage. Flight aspect photographs and telemetry records show that the STRAP V objectives have been met. The STRAP IV major error contributors have been significantly reduced and the tracking flexibility has been increased with only minor error contributions. Attention is given to the basic STRAP III control modes, major STRAP IV system error sources, tuned restrained inertial gyros (TRIGs), the programmable sequence timer, the STRAP V control box, third axis update, system gyro alignments, and STRAP V operational capabilities.

Budney, T. J.↗

Development of a magnetic acquisition and attitude control system for spinning rocket payloads

An attitude control system capable of pointing the roll principle axis of a spinning payload to within one degree of the magnetic field vector was flown successfully in 1981-82 aboard three Black Brant X payloads and one Terrier Malemute payload, and additional flights with the system have been requested. Using a filtered linear combination of signals provided by a single-axis rate gyro and a two-axis magnetometer, and control actuation from two cold-gas thrusters, the system can be assembled from standard rocket components and fitted to any payload size.

Olney, D. J.↗

Attitude Control by Localized Outgassing

Attitude control of levitated object achieved by using laser to vaporize selectively sublimate coating. Laser heats material that will sublime or outgas. To obtain torque reaction force vector from subliming material must not pass through center-of-mass of object. Laser provides beam suitable for controlling objects in noncontact manufacturing processes in acoustic levitation chambers.

Elleman, D. D.↗

Study of tethered satellite active attitude control

Existing software was adapted for the study of tethered subsatellite rotational dynamics, an analytic solution for a stable configuration of a tethered subsatellite was developed, the analytic and numerical integrator (computer) solutions for this "test case' was compared in a two mass tether model program (DUMBEL), the existing multiple mass tether model (SKYHOOK) was modified to include subsatellite rotational dynamics, the analytic "test case,' was verified, and the use of the SKYHOOK rotational dynamics capability with a computer run showing the effect of a single off axis thruster on the behavior of the subsatellite was demonstrated. Subroutines for specific attitude control systems are developed and applied to the study of the behavior of the tethered subsatellite under realistic on orbit conditions. The effect of all tether "inputs,' including pendular oscillations, air drag, and electrodynamic interactions, on the dynamic behavior of the tether are included.

Colombo, G.↗

Attitude control and drag compensation propulsion system for Gravity Probe-B spacecraft

An on board propulsion system for attitude control and drag compensation is presented which uses helium boiloff gas from an experiment package dewar as propellant. This boiloff gas would normally be vented nonpropulsively. Use of a small allowable temperature range in the dewar is exploited to store helium and accommodate incompatibilities in dewar heat leak and thruster demand flow over periods of more than one orbit. A relatively detailed thermodynamics analysis of the two phase helium dewar and simulation of pressure loss through the helium distribution system is included.

Blount, D. H.↗

Method of damping nutation motion with minimum spin axis attitude disturbance

In a method of and apparatus for damping nutation of a spinning spacecraft, spin axis attitude disturbances are substantially reduced by controlling at least one nutation damping gas thruster to fire with nonuniform gas pulses. During the beginning of a nutation control sequence, the duration of successive gas pulses is gradually increased (up pulsed) from zero to a predetermined maximum duration. The duration of successive pulses is then maintained constant for a time period. Finally, at the end of the nutation control sequence, the duration of successive gas pulses is gradually reduced to zero (down pulsed). Up pulsing of the gas thruster is initiated in response to a predetermined maximum nutation angle measured by an accelerometer. Down pulsing of the thruster is initiated in response to a predetermined minimum nutation angle.

Hoffman, H. C.↗

Development of the functional simulator for the Galileo attitude and articulation control system

A simulation program for verifying and checking the performance of the Galileo Spacecraft's Attitude and Articulation Control Subsystem's (AACS) flight software is discussed. The program, which is called Functional Simulator (FUNSIM), provides a simple method of interfacing user-supplied mathematical models coded in FORTRAN which describes spacecraft dynamics, sensors, and actuators; this is done with the AACS flight software, coded in HAL/S (High-level Advanced Language/Shuttle). It is thus able to simulate the AACS flight software accurately to the HAL/S statement level in the environment of a mainframe computer system. FUNSIM also has a command and data subsystem (CDS) simulator. It is noted that the input/output data and timing are simulated with the same precision as the flight microprocessor. FUNSIM uses a variable stepsize numerical integration algorithm complete with individual error bound control on the state variable to solve the equations of motion. The program has been designed to provide both line printer and matrix dot plotting of the variables requested in the run section and to provide error diagnostics.

Namiri, M. K.↗

Attitude control and stability of a Space Station

Certain problems arise in connection with the design and construction of a Space Station. These problems are partly related to the impossibility to predict in advance the ultimate form and size which the Space Station will assume. Due to the abatement of volume and strength constraints it will be desirable (for maximum utility of mass) to permit very low structural resonance frequencies, and due to complexity of the configuration there will be an extremely high density of modal frequencies. The basic approaches available to an attitude control system designer for coping with the dynamics of a plant with the considered characteristics are examined. In order to overcome difficulties related to a use of currently widely considered approaches, a technique is proposed whereby the degrees of freedom requiring active control are isolated mechanically from other superfluous vibratory modes.

Peters, W. H.↗

IPACS Attitude Control Technology Considerations

Larger facilities or the Space Station and its evolutionary versions are considered for the control bandwidth which will evolve to lower values, probably in the 0.01 to 0.1 hertz range. An integrated power attitude control systems (IPACS) unit that incorporates conventional mechanical bearings to have a bandwidth of 4-10 hertz is expected. If the IPACS unit incorporates the advanced technology magnetic bearing, a bandwidth of 1.2 hertz is expected. It is found that for the Space Station or even the Space Platform, either of the above IPACS concepts are adequate.

Brandon, L.↗

Modular design attitude control system

The problem of applying modular attitude control to a rigid body-flexible suspension model of a flexible spacecraft with some state variables inaccessible was addressed by developing a sequence of single axis models and generating a series of reduced state linear observers of minimum order to reconstruct those scalar state variables that were inaccessible. The specific single axis models treated consisted of two, three and four rigid bodies, respectively, interconnected by a flexible shaft passing through the mass centers of the bodies. Reduced state linear observers of all orders up to one less than the total number of scalar state variables were generated for each of the three single axis models cited.

Chichester, F. D.↗

Modular design attitude control system

The problem of applying modular attitude control to a rigid body - flexible suspension model of a flexible spacecraft with some state variables inaccessible was addressed by developing a sequence of single axis models and generating a series of reduced state linear observers of minimum order to reconstruct those scalar variables that were inaccessible. The specific single axis models treated consisted of two, three and four rigid bodies, respectively, interconnected by a flexible shaft passing through the mass centers of the bodies. Reduced state linear observers of all orders up to one less than the total number of scalar state variables were generated for each of the three single axis models cited.

Chichester, F. D.↗

Galileo attitude and articulation control subsystem closed loop testing

In order to ensure the reliable operation of the Attitude and Articulation Control Subsystem (AACS) which will guide the Galileo spacecraft on its two and one-half year journey to Jupiter, the AACS is being rigorously tested. The primary objectives of the test program are the verification of the AACS's form, fit, and function, especially with regard to subsystem external interfaces and the functional operation of the flight software. Attention is presently given to the Galileo Closed Loop Test System, which simulates the dynamic and 'visual' flight environment for AACS components in the laboratory.

Lembeck, M. F.↗