SEARCH · Engineering Papers

Results for “volume”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Revisiting a Drag Partition Model For Canopy-Like Roughness Elements

Turbulent flows over a large surface area (S) covered by n obstacles experience an overall drag due to the presence of the ground and the protruding obstacles into the flow. The drag partition between the roughness obstacles and the ground is analyzed using an analytical model proposed by Raupach (Boundary-Layer Meteorol 60:375-395, 1992) and is hereafter referred to as R92. The R92 is based on the premise that the wake behind an isolated roughness element can be described by a shelter area A and a shelter volume V. The individual sizes of A and V without any interference from other obstacles can be determined from scaling analysis for the spread of wakes. To upscale from an individual roughness element to n/S elements where wakes may interact, R92 adopted a background stress re-normalizing instead of reducing A or V with each element addition. This work demonstrates that R92’s approach results in a linear background stress reduction in A and V only when the ratio of n/S is small, due to a low probability of wake interactions. This probabilistic nature suggests that up-scaling from individual to multiple roughness elements can be re-formulated using stochastic averaging methods proposed here. The two approaches are shown to recover R92 under plausible conditions. An alternative scaling for the shelter volume is also proposed here using thermodynamic arguments of work and dissipation though the final outcome remains similar to R92. Comparisons between R92 and available data spanning more than two decades after R92 on blocks and vegetation-like roughness elements confirm the practical utility of R92. The agreement between R92 and this updated databases of experiments and simulations confirm the potential use of R92 in large-scale models provided that the relevant parameters accommodate certain features of the roughness element type (cube versus vegetation-like) and, to a lesser extent, their configuration throughout S. Last, a comparison between R92 and models based on first-order closure principles with constant mixing length suggests that R92 can outperform such models when evaluated across a wide range of roughness densities.

canopy turbulence↗

DOE OSTI2021

Attributable human-induced changes in the magnitude of flooding in the Houston, Texas region during Hurricane Harvey

Abstract The human influence on precipitation during tropical cyclones due to the global warming is now well documented in the literature. Several studies have found increases in Hurricane Harvey’s total precipitation over the Greater Houston area ranging from the Clausius-Clapeyron limit of 7% to as much as 38% locally. Here we use a hydraulic model to translate these attribution statements about precipitation to statements about the resultant flooding and associated damages. We find that while the attributable increase in the total volume of flood waters is the same as the attributable increase in precipitation, the attributable increase in the total area of the flood is less. However, we also find that in the most heavily flooded parts of Houston, the local attributable increases in flood area and volume are substantially larger than the increase in total precipitation. The results of this storyline attribution analysis of the Houston flood area are used to make an intuitive best estimate of the cost of Hurricane Harvey attributable to anthropogenic global warming as thirteen billion US dollars.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Pressure-Dependent Thermal Expansion Coefficient by a Diamond Anvil Cell

A thermal expansion coefficient (αp) is an essential thermophysical quantity for high-pressure research. The thermal expansion coefficient is the volume change over the temperature in an isobaric heating process. Although isobaric heating processes for diamond anvil cell (DAC) have been conducted by keeping the pressure constant during heating, pressure determination at high-temperature high pressure is debatable for decades long. In this paper, a revertible heating/cooling approach is presented, while its pressure determination at high-temperature high pressure is not required. We report a pressure-dependent thermal expansion coefficient of MgO at 9.5 GPa by reversible heating/cooling was determined by a DAC and its result matches the one collected by a large volume press, whose isobaric heating was conducted by manually adjusting its load/pressure.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Droplet Evaporation-Based Approach for Microliter Fuel Property Measurements

Small-volume, high-throughput screening techniques are sought to enable downselection from a large candidate pool of bio-blendstocks to a select few, having physical properties consistent with requirements of downsized, turbo-boosted internal combustion engines. Herein, this work presents a droplet evaporation-based approach to predict heat of vaporization, vapor pressure, diffusion coefficient, and Lennard–Jones parameters for an unknown fuel. Two different schemes, considering the isothermal evaporation of a moving droplet in ambient air, are proposed, which combine droplet velocity and temperature measurements, with some known properties to predict unknown properties. The schemes utilize an inverse solution of a transient model of droplet evaporation solved in an iterative fashion. A baseline scheme, which only requires droplet size change measurements, is evaluated using test data for three liquid fuels, comprising of alkanes and alcohols, as obtained in a temperature-controlled chamber. Results yield temperature-dependent heat of vaporization and vapor pressure predictions within 10 % and 22 %, respectively, of reference values. The advanced scheme, which additionally requires droplet temperature measurement, is numerically evaluated in the current work and will be experimentally validated in future efforts. The advanced scheme is found to significantly improve prediction quality, with deviations less than 2 % and 1 % for heat of vaporization and vapor pressure, while also predicting diffusion coefficient and Lennard–Jones parameters within 5 % and 8 %, respectively. The combined set of approaches, which primarily track droplet evaporation, can be incorporated into a small-volume, high-throughput fuel screening process.

09 BIOMASS FUELS↗

DOE OSTI2022

Voronoi Meshing to Accurately Capture Geological Structure in Subsurface Simulations

Mesh generation lies at the interface of geological modeling and reservoir simulation. Highly skewed or very small grid cells may be necessary to accurately capture the geometry of geological features, but the resulting poorly scaled or small grid cells can have a substantial negative impact on simulator accuracy and speed. One way to minimize numerical errors caused by gridding complex structures is to simulate on high-quality Voronoi meshes, which reduce grid orientation effects in fluid flow. This work presents a complete methodology to create Voronoi simulation grids, model fluid flow in complex geological systems, and visualize the results. A recently developed Voronoi meshing method that can automatically generate provably good unstructured meshes that conform to input surfaces creating closed volumes is used. Initially an analytical benchmark simulation is presented to validate the quality of the meshes and simulation results and demonstrate the superiority of simulation results using Voronoi meshes over flexed-hexahedral meshes on a domain with internal features. Next, meshes are created for test structures representing four of the most common geological features in the subsurface: layering, pinch-out, an interior lens that tapers to zero thickness on all sides and a fault with offset. Two benchmark flow simulations are run for each test structure. Finally, a realistic geological example for CO 2 injection into an anticline is simulated. Three realizations of the Voronoi mesh at the same resolution are generated for the simulations. Each mesh is highly refined near the injection wells and coarse in areas of less interest. These three meshes are used to model the CO 2 plume in the subsurface as it migrates to the top of the structure and then fills downward. Simulations on the meshes with randomly generated elements inside the input volumes each give slightly different fingering patterns for the viscous-unstable buoyant gas flow. The results presented in this work show a promising step towards utilizing fully automated Voronoi meshing for subsurface flow simulations in complex geology.

58 GEOSCIENCES↗

DOE OSTI2023

Rapid in situ nutrient element distribution in plants and soils using laser-induced breakdown spectroscopy ($\mathrm{LIBS}$)

The aim of this study is to develop and test the applicability of a rapid in situ plant chemistry profiling technique to determine elemental composition of small-volume plant and soil samples obtained from a woody bioenergy crop species, Populus trichocarpa. Expanding the research tools available to characterize the nutrient element correlations among plant tissue types and soil depths is a critical need in the path of understanding productivity and adaptation of plants to variations in external abiotic and biotic factors and developing sustainable perennial bioenergy crops that are co-optimized for biomass valorization aboveground and carbon sequestration belowground. Several plant root, stem, and soil samples were tested using laser-induced breakdown spectroscopy (LIBS) to evaluate the presence and distribution of nutrient elements. Samples were tested as collected and after being dried and cross sectioned to evaluate the effectiveness of using LIBS for in situ analysis on plant samples. The collected LIBS spectra show the elemental peaks were the same in both the as collected and prepared samples for roots and stems. Qualitative amounts of elements such as H, C, N, O, Li, Na, Mg, K, Ca, Fe, Al, and Si were able to be identified rapidly in raw samples. Here in this report we demonstrate suitability of LIBS in obtaining rapid, in situ, elemental distribution in plant and soil samples, utilizing only small sample volumes and minimal sample preparation. This demonstration opens up a new rapid phenotyping avenue necessary to fill the asymmetrical knowledge gaps in belowground performance of plant systems.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Path-Integrated X-Ray Images for Multi-Surface Digital Image Correlation (PI-DIC)

X-ray imaging offers unique possibilities for Digital Image Correlation (DIC), opening the door for full-field deformation measurements of a test article in complex environments where optical DIC suffers severe biases or is impossible. While X-ray DIC has been performed in the past with standard DIC codes designed for optical images, the path-integrated nature of X-ray images places constraints on the experimental setup, predominantly that only a single surface of interest moves/deforms. These requirements are difficult to realize for many practical situations and limit the amount of information that can be garnered in a single test. Other X-ray based diagnostics such as Digital Volume Correlation (DVC) and Projection DVC (P-DVC) overcome these obstacles, but DVC is limited to quasi-static tests, and both DVC and P-DVC necessitate high-resolution computed tomography (CT) scan(s) and often require a potentially invasive pattern throughout the volume of the specimen. Here this work presents a novel approach to measure time-resolved displacements and strains on multiple surfaces from a single series of 2D, path-integrated (PI) X-ray images, called PI-DIC. The principle of optical flow or conservation of intensity—the foundation of DIC—was reframed for path-integrated images, for an exemplar setup comprised of two plates moving and deforming independently. Synthetic images were generated for rigid translations, rigid rotations, and uniform stretches, where each plate underwent a unique motion/deformation. Experimental specimens were fabricated (either an aluminum plate with tantalum features or a plastic plate with steel features) and the two specimens were independently translated. PI-DIC was successfully demonstrated with the synthetic images and validated with the experimental images. Prescribed displacements were recovered for each plate from the single set of path-integrated, deformed images. Errors were approximately 0.02 px for the synthetic images with 1.5% image noise, and 0.05 px for the experimental images. These results provide the foundation for PI-DIC to measure motion and deformation of multiple, independent surfaces with subpixel accuracy from a single series of path-integrated X-ray images.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

The Application of Differential Scanning Calorimetry to Investigate Precipitation Behavior in Nickel-Base Superalloys Under Continuous Cooling and Heating Conditions

In this study, a suite of experimental tools and fast-acting, numerical-simulation techniques was used to quantify the precipitation behavior of three nickel-base superalloys: IN-100, LSHR, and 718. Experimental methods comprised differential scanning calorimetry (DSC) to establish the specific heat as a function of temperature and selected direct-resistance heating trials (using a Gleeble ® machine) to obtain samples for microstructural analysis. For the DSC experiments, each alloy was cooled at a prescribed constant rate (between 5 and 20 K/min) after an initial soak/equilibration in the high-temperature, single-phase (supersolvus) temperature regime. On-heating DSC trials beginning at ambient temperature were also performed on alloy 718 in three different starting conditions: super- δ -solvus solution treated and water quenched (denoted as ST), solution treated and aged (STA), and solution treated and overaged (STOA). DSC results, revealing the thermal signatures associated with the kinetics of precipitation of γ ' (IN-100, LSHR) or γ ' and γ " (718), were interpreted using a previously-developed fast-acting routine that treats concurrent nucleation, growth, coarsening, and dissolution. For these simulations, special attention was paid to various thermo-kinetic input parameters including equilibrium solvus-approach curves, bulk free energies of transformation, matrix-precipitate interface energies, and effective diffusivities. For the γ - γ ' superalloys (IN-100 and LSHR), estimates of precipitate volume fraction as a function of temperature from the specific-heat data revealed semi-quantitative agreement with simulation predictions. For the γ - γ '- γ " superalloy (718), simulation predictions of precipitate volume fractions were converted to specific heat as a function of temperature and showed semi-quantitative agreement with the direct measurements.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Quantifying Pore Morphology in Spray-Formed Tantalum Using X-ray Micro-computed Tomography

In order to establish quantitative process–structure–property relationships in thermal spray coatings, a robust framework for defining (micro)structural characteristics is needed. Here, we present a quantitative characterization of the three-dimensional morphology of porosity in spray-formed tantalum samples based on high-resolution X-ray micro-computed tomography. Using synchrotron facilities, we acquired dozens of high-resolution scans, enabling a statistically meaningful comparison across multiple samples, different regions within samples, and spray processes. We quantify the spatial distribution, size, and topology of porous inclusions, with a significant focus on variability across samples and different spray processes (plasma and cold sprayed), as well as sensitivity to image segmentation and resolution. Based on a typical segmentation, we report porosities ranging from 0.9 to 1.7 pct for all samples tested, with significant sensitivity due to image segmentation resulting in estimates as low as 0.6 pct and as high as 4.8 pct. For the complex pore space morphology observed in these materials, we argue that a conventional analysis based on identifying individual pores is not well suited, and propose an alternative approach based on morphological metrics with a rich history in porous media literature, such as spatial correlations, local pore thickness, and scale-dependent sub-sampling. Spatial correlations indicate anisotropic splat structures, but only mildly anisotropic pores. Various measures of pore size show a wide distribution of sizes, ranging from sub-micron to 10-micron length scales. Scale-dependent variations in porosity suggest that representative volumes of several hundred microns are required for convergence of morphological metrics, with larger volumes for cold-spray materials. This work provides a robust quantitative basis for describing three-dimensional pore structure in thermal spray coatings.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Effects of Remelting Current on Structure, Composition, Microsegregation, and Inclusions in Inconel 718 Electroslag Remelting Ingots

The macro- and microstructures, chemical compositions, microsegregations, and nonmetallic inclusion characteristics at different positions of the as-cast IN718 ingots produced by a laboratory-scale electroslag remelting (ESR) furnace under four remelting currents (150, 200, 250, and 300 A) were compared and investigated comprehensively. The results indicate that the average melting rate increases with the increasing remelting current, and the molten pool tends to be deeper. Thus, at the same position of the ESR ingots, the volume fraction of the segregated phase, the degree of elemental segregation, and the secondary dendrite arm spacing have the same tendency to increase with the increasing remelting current and show an increasing trend from the bottom to the top along the height of each ingot. If the current is set relatively low, the oxygen and nitrogen levels in the ingots increase, the conditions that make the contents and distributions of Al and Ti become unstable. In addition, the major nonmetallic inclusions in the IN718 ESR ingots are MgO·Al{sub 2}O{sub 3} complex oxide inclusions with a three-layer structure and (Nb,Ti)N nitrides. The volume fractions and mean equivalent diameters display a downward trend with the increasing remelting current. The size and quantity of these inclusions are always larger in the upper portions of the ingots than those in the lower portions.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Inkjet printing of epitaxially connected nanocrystal superlattices

Access to a blossoming library of colloidal nanomaterials provides building blocks for complex assembled materials. The journey to bring these prospects to fruition stands to benefit from the application of advanced processing methods. Epitaxially connected nanocrystal (or quantum dot) superlattices present a captivating model system for mesocrystals with intriguing emergent properties. The conventional processing approach to creating these materials involves assembling and attaching the constituent nanocrystals at the interface between two immiscible fluids. Processing small liquid volumes of the colloidal nanocrystal solution involves several complexities arising from the concurrent spreading, evaporation, assembly, and attachment. The ability of inkjet printers to deliver small (typically picoliter) liquid volumes with precise positioning is attractive to advance fundamental insights into the processing science, and thereby potentially enable new routes to incorporate the epitaxially connected superlattices into technology platforms. In this study, we identified the processing window of opportunity, including nanocrystal ink formulation and printing approach to enable delivery of colloidal nanocrystals from an inkjet nozzle onto the surface of a sessile droplet of the immiscible subphase. We demonstrate how inkjet printing can be scaled-down to enable the fabrication of epitaxially connected superlattices on patterned sub-millimeter droplets. Furthermore, we anticipate that insights from this work will spur on future advances to enable more mechanistic insights into the assembly processes and new avenues to create high-fidelity superlattices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2024

Phase Identification in Synchrotron X-ray Diffraction Patterns of Ti–6Al–4V Using Computer Vision and Deep Learning

X-ray diffraction patterns contain information about the atomistic structure and microstructure (defect population) of materials, extracting detailed information from diffraction patterns is complex, demanding and relies on prior knowledge. Here, we hypothesize that deep-learning techniques can help to perform an effective and accurate analysis with high throughput rates. To demonstrate this concept, we applied a novel deep learning framework to determine the evolution of the β-phase volume fraction in a Ti–6Al–4V alloy during heat-treatment from video sequences of 2D diffraction patterns recorded in transmission and with highly monochromatic radiation in a synchrotron beamline. In particular, we studied the impact of network design on prediction reliability and computational performance. Networks of different architectures were trained using 3008 experimental 2D patterns. A well-tuned model was found to reproduce the phase fractions of another experimental data set, consisting of 1100 diffraction patterns, with a mean-square error as small as 2.6 x 10 -4 . The average prediction error of β-phase volume fraction was within 1.6 x 10 -2 (in each diffraction pattern) of the values obtained by conventional methods. Our work demonstrates that convolutional neural networks can evaluate high energy X-ray diffraction patterns with a remarkable level of reliability. Furthermore, it demonstrates the significance of network design on the reliability of predictions and computational performance. The most complex models do not necessarily result in highest accuracy and may even fail to learn from the data.

36 MATERIALS SCIENCE↗

DOE OSTI2025

3D printing of packaging inserts from biomass-fungi composites: Environmental sustainability analysis

In this study, a comprehensive Life cycle assessment (LCA) is conducted on molded packaging inserts from expanded polystyrene (EPS) foam, molded packaging inserts from biomass-fungi composite, and 3D-printed packaging inserts from biomass-fungi composite under the low mix / high volume (LMHV) scenario and molded and machined packaging inserts from EPS foam, molded and machined packaging inserts from biomass-fungi composite, and 3D-printed packaging inserts from biomass-fungi composite under the high mix / low volume (HMLV) scenario. Six environmental impact categories—climate change, acidification, eutrophication, fossil resource scarcity, land use, and water consumption—are analyzed to evaluate the environmental trade-offs associated with each type of packaging inserts. Under the LMHV scenario, molded packaging inserts from biomass-fungi composite emerge as the best option due to their lower impact on climate change, acidification and water consumption compared to other types of packaging inserts. Conversely, molded packaging inserts from biomass-fungi composite face challenges in land use and eutrophication, primarily due to raw material production. LCA also reveals that 3D-printed packaging inserts from biomass-fungi composite are the most environmentally favorable option under the HMLV scenario, due to significantly lower contributions to climate change, eutrophication, and water consumption compared to other types of packaging inserts. Conversely, 3D-printed packaging inserts from biomass-fungi composite face challenges in acidification and land use, primarily due to raw material production. As part of the LCA, sensitivity analyses show that sourcing energy from 100% renewable sources substantially lowers climate change impacts across all packaging types, while varying transportation distances results in only minor changes, indicating the dominant role of upstream material and manufacturing processes. Additional sensitivity analysis is conducted under the HMLV scenario to assess the impact of material removal during machining on the environment. The amount of material removal is varied from 10 to 70% for the sensitivity analysis and it highlights that the amount of material removed during machining has no significant impact on climate change for packaging inserts from EPS foam. However, molded and machined packaging inserts from biomass-fungi composite show an increasing trend in climate change with higher amount of material removal, while 3D-printed packaging inserts from biomass-fungi composite exhibit a decreasing trend, driven by reduced raw material usage and energy consumption.

09 BIOMASS FUELS↗

DOE OSTI2020

Plastic deformation of single crystals of the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy in tension and compression from 10 K to 1273 K

In this report the plastic deformation behavior of single crystals of the quinary, equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111}<110> slip at room temperature is 42-45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111}<110> slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ($\bar1\bar11$) planes in the form of Lüders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Mechanisms of Ti 3 Al precipitation in hcp α -Ti

Here, nucleation and growth of Ti3Al α( 2 ) ordered domains in alpha-Ti-Al-X alloys were characterised using a combination of transmission electron microscopy, atom probe tomography and small angle X-ray scattering. Model alloys based on Ti-7Al (wt.%) and containing O, V and Mo were aged at 550 °C for times up to 120d and the resulting precipitate dispersions were observed at intermediate points. Precipitates grew to around 30nm in size, with a volume fraction of 6-10% depending on tertiary solutes. Interstitial O was found to increase the equilibrium volume fraction of α 2 , while V and Mo showed relatively little influence. Addition of any of the solutes in this study, but most prominently Mo, was found to increase nucleation density and decrease precipitate size and possibly coarsening rate. Coarsening can be described by the Lifshitz-Slyozov-Wagner model, suggesting a matrix diffusion-controlled coarsening mechanism (rather than control by interfacial coherency). Solutionising temperature was found to affect nucleation number density with an activation energy of E f = 1.5 +/- 0.4 eV, supporting the hypothesis that vacancy concentration affects α 2 nucleation. The observation that all solutes increase nucleation number density is also consistent with a vacancy-controlled nucleation mechanism.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Designing shape-memory-like microstructures in intercalation materials

During the reversible insertion of ions, lattices in intercalation materials undergo structural transformations. These lattice transformations generate misfit strains and volume changes that, in turn, contribute to the structural decay of intercalation materials and limit their reversible cycling. In this paper, we draw on insights from shape-memory alloys, another class of phase transformation materials, that also undergo large lattice transformations but do so with negligible macroscopic volume changes and internal stresses. We develop a theoretical framework to predict structural transformations in intercalation compounds and identify crystallographic design rules necessary for forming shape-memory-like microstructures in intercalation materials. We use our approach to systematically screen open-source structural databases comprising $n$ > 5000 pairs of intercalation compounds. We identify candidate compounds, such as Li x Mn 2 O 4 (Spinel), Li x Ti 2 (PO 4 ) 3 (NASICON), that approximately satisfy the crystallographic design rules and can be precisely doped to form shape-memory-like microstructures. Throughout, we compare our analytical results with experimental measurements of intercalation compounds. We find a direct correlation between structural transformations, microstructures, and increased capacity retention in these materials. These results, more generally, show that crystallographic designing of intercalation materials could be a novel route to discovering compounds that do not decay with continuous usage.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Informed unsupervised machine learning analysis of dislocation microstructure from high-resolution differential aperture X-ray structural microscopy data

This study leverages high-resolution differential-aperture X-ray structural microscopy (DAXM) to probe the local dislocation structure in deformed 304L-stainless steel at small strain, by measuring the lattice rotation and deviatoric elastic strain with a sub-micron resolution. For a single grain in a polycrystalline specimen, the measured lattice rotation field over the measured volume exhibited a multimodal distribution while the deviatoric elastic strain showed a single-mode distribution. An unsupervised Cauchy mixture machine learning model was developed to resolve the multimodal distribution of the lattice rotation. By mapping the lattice rotation data associated with each Cauchy peak in the model back onto the measured volume, we identify contiguous regions of the crystal rotated near the average values corresponding to the peaks of the overall rotation distribution. These regions represent the grain subdivision in the microstructure. Finally, the dislocation density tensor was also computed and its norm was laid over the rotation field to detect the subgrain boundaries. This step provided a validation of the Cauchy mixture model for the analysis of the lattice rotation distribution. The current study highlights the integration of advanced X-ray microscopy techniques with data-driven analysis methods to uncover detailed microstructure scales in deformed crystals.

Machine learning; Lattice rotation; High-energy X-↗

DOE OSTI2025

Quantification of grain rotation in bulk nanostructured copper via in situ heating white beam synchrotron X-ray diffraction

Grain rotation during microstructural relaxation under heating is conventionally studied extensively through transmission electron microscopy and simulations. However, there is a shortage in examining grain rotations at larger length and volume scales in bulk materials. It is critical to understand the thermal stability of bulk nanostructured metals, since those enhanced mechanical properties have been well recognized. Here, this study aimed to employ a white beam microdiffraction X-ray technique under in situ heating from 300 K to 1073 K at 12 K/min on a nanostructured copper processed by high-pressure torsion, yielding an initial grain size of ∼260 nm before the heating. Evaluation across a wide range of temperatures reveals transition temperatures associated with microstructural relaxation processes. By tracking separate Laue diffraction peaks stemming from individual grains, changes in their orientations can be estimated and quantified. This approach becomes particularly effective when the number of grains within the probed volume is reasonably small. At temperatures above 940 K, about 7.5 % of Cu grains are rotating at speeds of ∼2 × 10 –3 °/s. The radial direction of the disk specimen is found to be the preferred direction of grain rotation, with the rotation axis along the shear direction. Further analysis found no correlation between peak intensity and peak size, related to grain sizes and deviatoric strain, respectively, with rotation conditions or speed. These findings demonstrate that the diffraction technique utilizing white beam X-rays is a complementary and novel characterization tool for understanding microstructural evolution, especially in grain rotations, of bulk crystalline materials.

Grain orientation↗