Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid solution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

Vacancy-induced dislocations within grains for high-performance PbSe thermoelectrics

To minimize the lattice thermal conductivity in thermoelectrics, strategies typically focus on the scattering of low-frequency phonons by interfaces and high-frequency phonons by point defects. In addition, scattering of mid-frequency phonons by dense dislocations, localized at the grain boundaries, has been shown to reduce the lattice thermal conductivity and improve the thermoelectric performance. Here we propose a vacancy engineering strategy to create dense dislocations in the grains. In Pb 1$-$x Sb 2x/3 Se solid solutions, cation vacancies are intentionally introduced, where after thermal annealing the vacancies can annihilate through a number of mechanisms creating the desired dislocations homogeneously distributed within the grains. This leads to a lattice thermal conductivity as low as 0.4Wm -1 K -1 and a high thermoelectric figure of merit, which can be explained by a dislocation scattering model. As a result, the vacancy engineering strategy used here should be equally applicable for solid solution thermoelectrics and provides a strategy for improving zT.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tuning discharge voltage by Schottky electron barrier in P2-Na 2/3 Mg 0.205 Ni 0.1 Fe 0.05 Mn 0.645 O 2

Recently, Mg doped Na metal oxide layered cathode compounds have attracted strong interest for Na-ion battery applications. We report a new type of asymmetric phase evolution between charge and discharge is found to show much-enhanced discharge voltage in P2-Na 2/3 Mg 0.205 Ni 0.1 Fe 0.05 Mn 0.645 O 2 over the parent cathode compound. P2 solid solution is found to show an abnormal coexistence with O2-P2 two-phase reaction during discharge with simultaneous reduction of O, Ni, and Fe redoxes, distinct from the conventional P2-O2 two-phase reaction in the charge. Our analysis suggests that the P2 and O2 two-phase boundary forms a novel unidirectional Schottky barrier to impede electron and Na diffusions in discharge only, thus making the kinetically preferred P2 solid solution phase abnormally coexist with the two-phase region for high discharge voltage and low polarization. Our work demonstrates tuning dynamic evolution of electronic Schottky barrier as a new dimension for advanced kinetic design of high-performance battery cathode materials.

25 ENERGY STORAGE↗

Structural studies of metal nanoparticles using high-energy x-ray diffraction

The XRD patterns of nanoparticles exhibit broad Bragg peaks because of small size, where the contribution of diffuse component provides us with inherent structural information. Therefore, pair distribution function obtained from a Fourier transformation of high-energy XRD data and structure modeling on the basis of diffraction data becomes an essential tool to understand the structure of nanoparticles. This promising tool was utilized to obtain structural information of Pd/Pt bimetallic core/shell and solid-solution nanoparticles, which show much attention due to their improved hydrogen storage capacity and catalytic activity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

First Principle based Thermal Conductivity Modeling of Metal Alloys with Applications on Uranium Alloys

Thermal conductivity is an important materials property related to heat transport, which is essential to many applications, ranging from thermoelectrics to nuclear reactor materials. High- quality thermal conductivity data is critical to these materials and their associated technologies, including the nuclear fuel materials like traditional oxide fuels and metallic uranium (U) fuels, e.g. U-Zr and U-Mo alloys. And thermal conductivity modeling is widely used to interpolate or extrapolate experimental data, to obtain high-quality thermal conductivity data over wide temperature and composition range, and to understand the impacts of different factors including defects and microstructures. However, a general thermal conductivity model for metal alloys which can work regrading different phase components is still missing. Also, for U alloys, a thermal conductivity model working with different phases is needed. Therefore, in this work, we developed thermal conductivity models for metal alloys, based on ab-initio calculations, semi-classical physics rules, and limited experimental data. The goals of these models are to help obtain high- quality thermal conductivity data within a little experimental input as possible, have models that are extendable to varying microstructures, including different types of irradiation effects, and provide mechanistic understanding of heat transfer in the modeled alloys. In this work, our model solves several challenges in the development. The DFT-BTE approach is applied to decrease the reliance on experimental data and make the model extendable to composition changes and defects. A practical and efficient way to combine the DFT inputs with physics rules is pointed out in this work too. A staged approach, which starts from simple cases of elemental metals, then extends to solid solutions, different compound phases, and multi-phase mixtures, is presented to work with the metal alloys in different phase components. Our models are demonstrated respectively on aU for elemental metal model, on U-Zr and U-Mo alloys in aU temperature range for multi-phase mixture model, on high-temperature U-Zr, U-Nb, and U-Mo alloys in the body-centered cubic phase for concentrated solid solution model, and on irradiated U-Mo alloys for irradiated metal alloy model. All models show great agreement with experimental data. In these demonstrations, our model shows its advantages compared to previous empirical fitting model. Our model requires fewer experimental data, due to the inputs from DFT. The quantitative insights into the different physical factors are provided in our model, as it incorporates the electron and phonon scattering mechanisms. Our model also can be extended to incorporate the contributions of point defects, grain boundaries, and noble gas bubbles, to integrate their effects on heat transfer. This model can serve as both a foundation for understanding the more complex thermal conductivity of realistic U alloy fuels and a useful tool to guide further modeling of thermal conductivity to aid materials and device design.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Computational Design of Interlayers for Thermally Stable Compositionally Graded Coatings on Nickel Alloys

To extend the service life of Ni-based superalloys, refractory metal coatings are often used. However, direct bonding between metals with dissimilar crystal structure promotes brittle intermetallic phase formation. This work presents a computational thermodynamic framework for high throughput design of functionally graded interlayers to suppress deleterious phases that may form at the interlayer. The Thermo-Calc software package was used to screen candidate metallic interlayer elements based on stability of solid-solution phases. Vanadium was identified as a promising interlayer due to its consistent suppression of intermetallic phases. Temperature-dependent phase diagram mapping between 600 and 1000 °C guided selection of a compositional pathway that significantly reduced intermetallic formation compared to directly joining the Ni-based and Nb refractory alloys. Time–temperature–transformation analysis was performed to assess whether equilibrium-predicted phases are kinetically accessible along regions of the graded path where non-solid-solution phases are not fully suppressed. The methodology was further applied to additional Ni-based alloy and coating systems, illustrating its transferability as an approach for rapid computational design of graded interlayers in dissimilar high-temperature materials.

36 MATERIALS SCIENCE↗

Room temperature mechanosynthesis of the La{sub 1-x}Sr{sub x}MnO{sub 3{+-}{delta}} (0{<=}x{<=}1) system and microstructural study

Monophase nanocrystalline powders belonging to the La{sub 1-x}Sr{sub x}MnO{sub 3{+-}{delta}} system (0{<=}x{<=}1) with a perovskite structure have been obtained by mechanochemistry synthesis using a planetary ball milling equipment from La{sub 2}O{sub 3}, SrO, and Mn{sub 2}O{sub 3} mixtures. The solid state reaction was complete after one hour of milling treatment. For all the compositional range, the diffraction domain was very small and the structure appeared as a pseudo cubic perovskite. After annealing at 1100 Degree-Sign C under static air, the symmetry evolution due to the La substitution by Sr was analyzed by X-ray and electron diffraction. Samples with x=0, 0.25, 0.5, and 0.75 were assigned to R-3c space group (1 6 7) in the rhombohedral system and perovskite structure. However, the symmetry of the last term of the system (x=1), SrMnO{sub 3{+-}{delta}} sample, changed to P6{sub 3}/mmc space group (1 9 4) in the hexagonal system. The terms with x=0.8, 0.85, and 0.9 presented mainly rhombohedral symmetry. - Graphical abstract: SEM micrographs corresponding to milled (M) and Heated (H) samples: LaMnO{sub 3{+-}{delta}}(M1 and H1) La{sub 0.75}Sr{sub 0.25}MnO{sub 3{+-}{delta}}(M2 and H2,) and SrMnO{sub 3{+-}{delta}}(M8 and H8). Highlights: Black-Right-Pointing-Pointer Synthesis of La{sub 1-x}Sr{sub x}MnO{sub 3{+-}{delta}} by mechanochemistry, a very simple and scalable method. Black-Right-Pointing-Pointer System with rhombohedral perovskite structure forming a solid solution till x=0.9. Black-Right-Pointing-Pointer Powder material with nanometer character that reduces the sinterization temperature. Black-Right-Pointing-Pointer Appropriate Microstructure for cathode electrodes to built SOFCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and luminescence enhancement of Eu{sup 3+}, Sm{sup 3+} co-doped Li{sub 1.11}Ta{sub 0.89}Ti{sub 0.11}O{sub 3} phosphor

Graphical abstract: Enhancement of red emission intensity and internal- and external-quantum efficiencies by co-doping of Eu{sup 3+} and Sm{sup 3+} ion in Li{sub 1.11}Ta{sub 0.89}Ti{sub 0.11}O{sub 3} phosphor. - Abstract: Phosphors based on the Li{sub 1+x}Ta{sub 1−x}Ti{sub x}O{sub 3} solid solutions (0.05 ≤ x ≤ 0.25) as host materials were investigated. The optimal composition of the host for red-light emitting phosphor was found to be Li{sub 1.11}Ta{sub 0.89}Ti{sub 0.11}O{sub 3} (x = 0.11) when activated with Eu{sup 3+}. In this work, in order to further enhance the emission intensity, a series of Eu{sup 3+}- and Sm{sup 3+}-doped Li{sub 1.11}Ta{sub 0.89}Ti{sub 0.11}O{sub 3} phosphors was synthesized by solid-state reaction. The phosphor doped with 2.5 wt% Eu{sub 2}O{sub 3} and 0.1 wt% Sm{sub 2}O{sub 3} showed the highly efficient red-light emission upon excitation at 399 nm, with the internal quantum efficiency being 98%. Its PL intensity was ca. 1.4 times higher than that of the 2.5 wt% Eu{sup 3+}-doped Li{sub 1.11}Ta{sub 0.89}Ti{sub 0.11}O{sub 3} phosphor, indicating that the small amount of Sm{sup 3+} acted as an effective sensitizer.

36 MATERIALS SCIENCE↗

Strong Electron-Phonon Coupling Superconductivity Induced by a Low-Lying Phonon in IrGe

The physical properties of the previously reported superconductor IrGe and the Rh 1-x Ir x Ge solid solution are investigated. IrGe has an exceptionally high superconducting transition temperature (T c =4.7 K) among the isostructural 1:1 late-metal germanides MGe (M=Rh, Pd, Ir, and Pt). Specific-heat measurements reveal that IrGe has an anomalously low Debye temperature, originating from a low-lying phonon, compared to the other MGe phases. A large jump at T c in the specific-heat data clearly indicates that IrGe is a strong coupling superconductor. In the Rh 1-x Ir x Ge solid solution, a relationship between an anomalous change in lattice constants and the Debye temperature is observed. We conclude that the unusually high T c for IrGe is likely due to strong electron–phonon coupling derived from the presence of a low-lying phonon.

Hirai, Daigorou↗

Phase Stability and Optoelectronic Properties of the Bixbyite Phase in the Gallium–Indium–Tin–Oxide System

X‐ray diffraction techniques were used to determine the phase boundaries of the In 2 O 3 solid solution phase in the Ga 2 O 3 – In 2 O 3 – SnO 2 ternary system. The effects of Ga and Sn content on the unit cell dimensions of the bixbyite phase were calculated by a linear regression fit, the results of which indicate the two substitutive cations have opposite and independent effects on the lattice parameter. These results suggest that the cations do not strongly interact with each other in the crystal. Measurements of optoelectronic properties were also taken on single‐phase bulk specimens within the solid solution to establish their dependence on composition. As anticipated, Sn doping yields corresponding increases in conductivity, reduction in the absolute value of Seebeck coefficient, and increase in optical band gap. In contrast, these properties are not significantly affected by varying Ga content, confirming that Ga behaves as an isovalent dopant at the low doping levels involved.

Dolgonos, Alex↗

High-Entropy Oxides in the Mullite-Type Structure

High-entropy materials (HEMs) represent a new class of solid solutions containing at least five different elements. Their compositional diversity makes them promising as platforms for the development of functional materials. We synthesized new HEMs in a mullite-type structure and present five compounds, i.e., Bi 2 (Al 0.25 Ga 0.25 Fe 0.25 Mn 0.25 ) 4 O 9 and A 2 Mn 4 O 10 with variations of A = Nd, Sm, Y, Er, Eu, Ce, and Bi, demonstrating the vast accessible composition space. By combining scattering, microscopy, and spectroscopy techniques, we show that our materials are mixed solid solutions. Remarkably, when following their crystallization in situ using X-ray diffraction and X-ray absorption spectroscopy, we find that the HEMs form through a metastable amorphous phase without the formation of any crystalline intermediates. We expect that our synthesis is excellently suited to synthesizing diverse HEMs and therefore will have a significant impact on their future exploration.

36 MATERIALS SCIENCE↗

Fundamental Thermodynamic, Kinetic, and Mechanical Properties of Lithium and Its Alloys

Lithium alloying reactions are beneficial in promoting uniform plating and stripping of lithium metal in all-solid-state batteries. First-principles calculations are performed to predict thermodynamic, kinetic, and mechanical properties of lithium and several important Li–M alloys (M = Mg, Ag, Zn, Al, Ga, In, Sn, Sb, and Bi). While the Li–Mg binary system forms a solid solution, most other lithium–metal alloys prefer stoichiometric intermetallic compounds with common local motifs that enable fast Li diffusion. Lithium and Li-rich alloys exhibit an unusually flat energy landscape along paths that connect BCC to close-packed structures like FCC and HCP, with important implications for mechanical properties. Very low migration barriers for Li diffusion that rival those of superion conductors are predicted, both in pure Li and in Li–M intermetallics. However, vacancy concentration, which is crucial for substitutional diffusion, is predicted to be low in metallic Li and most Li–M intermetallics. Compounds such as B32 LiAl and LiGa as well as D0 3 Li 3 Sb and Li 3 Bi exhibit structural vacancies at higher ends of their voltage windows, which together with low migration barriers leads to exceptionally high Li mobilities. In the Li–Mg solid solution, the addition of Mg is found to decrease the vacancy tracer diffusion coefficient by an order of magnitude.

36 MATERIALS SCIENCE↗

Novel High Temperature Carbide and Boride Ceramics for Direct Power Extraction Electrode Applications. Final report

The current project aims to develop new carbide and boride ceramic materials that incorporate different metal elements (e.g., (Hf 1-x Zr x )B 2 , also called ceramic solid solutions) and understand the fundamental composition-processing-structure-property relationships for such materials. Specifically, nano powders and related nano-composites for selected mixed metal carbide and boride materials are synthesized from nano-scale mixed precursors obtained from solution-based processing via heat treatment in inert atmosphere. The obtained fine powders were then consolidated into dense ceramics via a novel flash sintering process. The mechanical properties and thermal oxidation resistance for the obtained materials were evaluated for these materials. It was found that different synthesis routes produced powders with somewhat different characteristics in terms of composition and microstructure, which then led to different properties for the final ceramics. The synthesis and processing methods demonstrated in this study might be adopted for developing other similar high temperature ceramics, while the mixed metal or solid solution ceramic materials obtained from this study might be used as hot electrodes for direction power extraction and other energy-related applications.

20 FOSSIL-FUELED POWER PLANTS↗

Multi-material direct ink writing and co-sintering of gadolinium oxide – zirconium oxide components

Methods for fabrication of multi-material or functionally graded ceramic composite architectures are of interest for numerous applications. However, conventional co-sintering of multi-material ceramic parts is a challenge because differences in the sintering behavior of the two materials leads to interfacial strain and, ultimately, component failure. Direct ink writing (DIW) is an extrusion-based additive manufacturing process that excels at multi-material printing because multiple extrusion nozzles can be installed on the same gantry system. Furthermore, the use of DIW as a method to fabricate multi-material ceramic green bodies offers an additional variable for controlling and potentially matching sintering kinetics in the slurry formulation used for two dissimilar feedstocks. In the work documented in this manuscript, we explored two strategies to successfully co-sinter multi-material ceramic oxides: slurry optimization to match sintering kinetics and material gradients to step from one material to another. This manuscript also quantifies the allowable mismatch that avoids part cracking in solid solution forming multi-material systems and discusses best strategies to reduce mismatch during co-sintering. Inks composed of gadolinium oxide (Gd 2 O 3 ) and zirconium oxide (ZrO 2 ), a surrogate for uranium oxide (UO 2 ), were thermally matched, which resulted in a sintering mismatch reduction of over 10%. It was found that ~1% mismatch is tolerable during debind cycles and that ~5% mismatch is manageable during sintering cycles after slurry formulations are optimized to match the sintering behavior. Use of continuous gradients is shown to reduce sintering mismatch, although geometric resolution may be lost due to solid solution formation.

Snarr, Patrick L. [Oak Ridge National Laboratory (↗

Exceptional enhancement of mechanical properties in high-entropy alloys via thermodynamically guided local chemical ordering

Understanding the local chemical ordering propensity in random solid solutions, and tailoring its strength, can guide the design and discovery of complex, paradigm-shifting multicomponent alloys. First, we present a simple thermodynamic framework, based solely on binary enthalpies of mixing, to select optimal alloying elements to control the nature and extent of chemical ordering in high-entropy alloys (HEAs). Next, we couple high-resolution electron microscopy, atom probe tomography, hybrid Monte-Carlo, special quasirandom structures, and density functional theory calculations to demonstrate how controlled additions of Al and Ti and subsequent annealing drive chemical ordering in nearly random equiatomic face-centered cubic CoFeNi solid solution. We establish that short-range ordered domains, the precursors of long-range ordered precipitates, inform mechanical properties. Specifically, a progressively increasing local order boosts the tensile yield strengths of the parent CoFeNi alloy by a factor of four while also substantially improving ductility, which breaks the so-called strength–ductility paradox. Finally, we validate the generality of our approach by predicting and demonstrating that controlled additions of Al, which has large negative enthalpies of mixing with the constituent elements of another nearly random body-centered cubic refractory NbTaTi HEA, also introduces chemical ordering and enhances mechanical properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dispersoid reinforced alloy powder and method of making

A method of making dispersion-strengthened alloy particles involves melting an alloy having a corrosion and/or oxidation resistance-imparting alloying element, a dispersoid-forming element, and a matrix metal wherein the dispersoid-forming element exhibits a greater tendency to react with a reactive species acquired from an atomizing gas than does the alloying element. The melted alloy is atomized with the atomizing gas including the reactive species to form atomized particles so that the reactive species is (a) dissolved in solid solution to a depth below the surface of atomized particles and/or (b) reacted with the dispersoid-forming element to form dispersoids in the atomized particles to a depth below the surface of said atomized particles. The atomized alloy particles are solidified as solidified alloy particles or as a solidified deposit of alloy particles. Bodies made from the dispersion strengthened alloy particles, deposit thereof, exhibit enhanced fatigue and creep resistance and reduced wear as well as enhanced corrosion and/or oxidation resistance at high temperatures by virtue of the presence of the corrosion and/or oxidation resistance imparting alloying element in solid solution in the particle alloy matrix.

36 MATERIALS SCIENCE↗

Dispersoid reinforced alloy powder and method of making

A method of making dispersion-strengthened alloy particles involves melting an alloy having a corrosion and/or oxidation resistance-imparting alloying element, a dispersoid-forming element, and a matrix metal wherein the dispersoid-forming element exhibits a greater tendency to react with a reactive species acquired from an atomizing gas than does the alloying element. The melted alloy is atomized with the atomizing gas including the reactive species to form atomized particles so that the reactive species is (a) dissolved in solid solution to a depth below the surface of atomized particles and/or (b) reacted with the dispersoid-forming element to form dispersoids in the atomized particles to a depth below the surface of said atomized particles. The atomized alloy particles are solidified as solidified alloy particles or as a solidified deposit of alloy particles. Bodies made from the dispersion strengthened alloy particles, deposit thereof, exhibit enhanced fatigue and creep resistance and reduced wear as well as enhanced corrosion and/or oxidation resistance at high temperatures by virtue of the presence of the corrosion and/or oxidation resistance imparting alloying element in solid solution in the particle alloy matrix.

36 MATERIALS SCIENCE↗