Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “powder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effect of the filler morphology on the crystallization behavior and dielectric properties of the polyvinylidene fluoride‐based composite

Abstract Ceramic/polymer composites can be chemically stable, mechanically strong, and flexible, which make them candidates for electric devices, such as pressure or temperature sensors, energy storage or harvesting devices, actuators, and so forth. Depending on the application, various electrical properties are of importance. Polymers usually have low dielectric permittivity, but increased dielectric permittivity can be achieved by the addition of the ceramic fillers with high dielectric constant. With the aim to enhance dielectric properties of the composite without loss of flexibility, 5 wt% of BaTiO 3 ‐Fe 2 O 3 powder was added into a polyvinylidene fluoride matrix. The powder was prepared by different synthesis conditions to produce core/shell structures. The effect of the phase composition and morphology of the BaTiO 3 ‐Fe 2 O 3 core/shell filler on the structure and lattice dynamics of the polymer composites was investigated. Based on the results of the thermal analysis, various parameters of ceramic/polymer composites were determined. Differences in the phase composition and morphology of the filler have an influence on the formation of various polyvinylidene fluoride allomorphs and the degree of crystallinity. Furthermore, the dielectric performances of pure polyvinylidene fluoride and the polymer/ceramic composites were measured.

Polymer Science↗
DOE OSTI2024

Observation of Thermally Induced Piezomagnetic Switching in Cu 2 OSeO 3 Polymorph Synthesized under High-Pressure

A polymorph of Cu 2 OSeO 3 with the distorted kagome lattice is successfully obtained using the high-pressure synthesis technique (Cu 2 OSeO 3 -HP). The structural analysis using X-ray and neutron powder diffraction suggests that the tetrahedral Cu 2+ clusters [similar to those in Cu 2 OSeO 3 ambient-pressure phase (Cu 2 OSeO 3 -AP)] exist in Cu 2 OSeO 3 -HP but with three symmetry inequivalent sites. No structural change is observed between 1.5 K and the room temperature. The complex magnetic H-T phase diagram is established based on the temperature- and field-dependent magnetization data, indicating two distinct antiferromagnetic phases at low and intermediate temperatures, in addition to the higher-temperature spin-glass-like phase. The low temperature phase is identified by neutron powder diffraction refinements as a canted noncollinear antiferromagnetic order with a weak ferromagnetic component along the b-axis. Size of the refined ordered moment is ≈1.00(4) µ B in Cu 2 OSeO 3 -HP, indicating a large enhancement compared to that of Cu 2 OSeO 3 -AP (≈0.61 µ B ). By applying a uniaxial stress, finite enhancement of weak ferromagnetic component in the noncollinear antiferromagnetic phase in Cu 2 OSeO 3 -HP is observed, which is the clear evidence of the piezomagnetic effect. Interestingly, the sign of the induced magnetization changes on heating from the low-temperature to the intermediate-temperature phases, indicating a novel piezomagnetic switching effect in this compound.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Kinetics and Mechanisms of ZnO to ZIF-8 Transformations in Supercritical CO2 Revealed by in situ X-ray Diffraction

ZIF-8 was synthesized in supercritical carbon dioxide (scCO2). In situ powder X-ray diffraction, ex situ microscopy and simulations, provides a encompassing view of the formation of ZIF-8 and intermediary ZnO@ZIF-8 composites in this nontraditional solvent. Time-resolved imaging exposed divergent physicochemical reaction pathways from previous studies of the growth of anisotropic ZIF-8 core@shell structures in traditional solvents. Synthetically relevant physio-chemical properties of scCO2 were integrated into classical nucleation theory, relating interfacial forces with 3D nu-cleation outcomes. The kinetics of crystallization were examined and displayed a characteristic signature of time- and temperature-dependent mechanisms over the extent of the reaction. Lastly, we show that subtle factors, such as the extent of reaction and the size/shape of sacrificial templates can tailor ZIF-8 composition and size, eliciting control over hierarchical porosity in a nonconventional green solvent.

Sinnwell, Michael A.↗
DOE OSTI2026

Exploding Bridgewire (EBW) Detonators: An Example of Synergistic Multiphysics

Exploding bridgewire (EBW) detonators are highly temporally reproducible explosive devices that require the rapid discharge of a high‐voltage capacitance to operate and so are immune to most of the accidental hazards associated with traditional electric detonators. They have been demonstrated to be safe enough for use in high‐consequence explosive applications. Despite continued use for over 82 years, understanding the exact mechanism of operation has remained elusive. Various researchers have ascribed either deflagration‐to‐detonation (DDT) or shock‐to‐detonation (SDT) phenomena observed in other explosive events to explain the science behind the successful engineering; however, a rigorous justification has been absent. Previously, we have demonstrated a complex interaction in EBW detonators between large electrical currents, non‐equilibrium thermodynamic material states, plasma physics, powder compaction phenomena, shock physics, photochemistry, and rapid conventional explosive chemical reaction processes. Specifically, we have made progress in understanding the complex multiphysics that operates in these detonators and demonstrating that it is a serendipitous synergy between UV light emitted from the arc formed as the bridge is electrically exploded and the accompanying short‐duration shock transmitted into the explosive powder bed that allows these devices to function at practical capacitor sizes and charge voltages. This insight not only places the topic on a firmer scientific footing but potentially enables new approaches to safe detonator design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Surface science insight note: A linear algebraic approach to elucidate native films on Fe 3 O 4 surface

Standard materials are often used to obtain spectra that can be compared to those from unknown samples. Spectra measured from these known substances are also used as a means of computing sensitivity factors to allow quantification by X-ray photoelectron spectroscopy (XPS) of less well-defined materials. Spectra from known materials also provide line shapes suitable for inclusion in spectral models which, when fitted to spectra, permit the chemical state for a sample to be assessed. Both types of information depend on isolating photoemission signals from the inelastically scattered signal. In this Insight note, technical issues associated with the use of XPS of as received Fe 3 O 4 powder sample surface are discussed. The Insight note is designed to show how linear algebraic techniques applied to data collected from a sample marketed as pure Fe 3 O 4 powder are used to verify that XPS has been performed on chemistry representative of the sample. The methods described in this Insight note can further be utilized in elucidating complex XPS data obtained from thin films formed or evolved during cyclic/non-steady use of complex (electro)catalyst surfaces, especially in the presence of contaminants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Integration of Highly Luminescent Lead Halide Perovskite Nanocrystals on Transparent Lead Halide Nanowire Waveguides through Morphological Transformation and Spontaneous Growth in Water

The integration of highly luminescent CsPbBr 3 quantum dots on nanowire waveguides has enormous potential applications in nanophotonics, optical sensing and quantum communications. On the other hand, CsPb 2 Br 5 nanowires have also attracted a lot of attention due to their unique water stability and controversial luminescent property. Here we first report the growth of CsPbBr 3 nanocrystals on CsPb 2 Br 5 nanowires by simply immersing CsPbBr 3 powder into pure water, CsPbBr 3-γ X γ (X = Cl, I) nanocrystals on CsPb 2 Br 5-γ X γ nanowires are then synthesized for tunable light sources. Systematic structure and morphology studies, including in-situ monitoring, revealed that CsPbBr 3 powder was first converted to CsPb 2 Br 5 microplatelets in water, followed by a morphological transformation from CsPb 2 Br 5 microplatelets to nanowires, which is a kinetic dissolution-recrystallization process controlled by electrolytic dissociation and supersaturation of CsPb 2 Br 5 . CsPbB r3 nanocrystals are spontaneously formed on CsPb 2 Br 5 nanowires when nanowires are collected from the aqueous solution. Raman spectroscopy, combined photoluminescence and SEM imaging confirm that the bright emission originates from CsPbBr 3-γ X γ nanocrystals while CsPb 2 Br 5-γ X γ nanowires are transparent waveguides. In conclusion, the intimate integration of nanoscale light sources with a nanowire waveguide is demonstrated through the observation of the wave guiding of light from nanocrystals and Fabry-Perot interference modes of the nanowire cavity.

42 ENGINEERING↗
DOE OSTI2022

Removal of phosphorus using biochar derived from Fenton sludge: Mechanism and performance insights

Abstract A phosphorus removal biochar adsorbent was prepared from Fenton sludge. The adsorption process was optimized, and its phosphorus adsorption mechanism was discussed. It was found that the phosphorus adsorption performance of biochar prepared from single Fenton sludge (FBC‐400) was better than that of co‐pyrolysis of Fenton sludge and bamboo powder. The optimum condition was that Fenton sludge pyrolyzed at 400°C (FBC‐400). FBC‐400 had a larger specific surface area than that prepared by co‐pyrolysis with bamboo powder. And the high content of iron element could provide a higher surface charge of the biochar, thereby increasing the electrostatic adsorption of phosphorus onto FBC‐400. The phosphorus adsorption was highly pH dependent by FBC‐400, which can enhance electrostatic adsorption and increase adsorption capacity in acidic conditions. The effect of coexisting anion on adsorption performance was mainly affected by CO 3 2− , reducing the adsorption capacity by at least 49%, whereas other anions had no obvious interference. The adsorption process of FBC‐400 accorded with the pseudo‐second‐order kinetic model and the Langmuir model, which indicated that the adsorption process was monolayer adsorption and mainly chemical adsorption, and the maximum saturated phosphorus adsorption capacity was 8.77 mg g −1 . The mechanisms for phosphorus adsorption were electrostatic adsorption and inner‐sphere complexing. 1 M NaOH was used for desorption, and the adsorption capacity remained at 81% in the fifth cycle. Practitioner Points The Fenton sludge biochar usage as an adsorbent could be a win‐win strategy to convert waste biomass to valuable ‐ product. The adsorption process accorded with the Langmuir model, the maximum phosphorus adsorption capacity was 8.77 mg/g at 25°C. The adsorption mechanisms were electrostatic adsorption and inner‐sphere complexing. 1M NaOH was used for desorption, and the adsorption capacity remained at 81% in the fifth cycle.

Liu, Yanfang↗
DOE OSTI2024

High pressure raman spectroscopy and X-ray diffraction of K2Ca(CO3)2 bütschliite: multiple pressure-induced phase transitions in a double carbonate

Abstract The crystal structure and bonding environment of K 2 Ca(CO 3 ) 2 bütschliite were probed under isothermal compression via Raman spectroscopy to 95 GPa and single crystal and powder X-ray diffraction to 12 and 68 GPa, respectively. A second order Birch-Murnaghan equation of state fit to the X-ray data yields a bulk modulus, $${K}_{0}=46.9$$ K 0 = 46.9 GPa with an imposed value of $${K}_{0}^{\prime}= 4$$ K 0 ′ = 4 for the ambient pressure phase. Compression of bütschliite is highly anisotropic, with contraction along the c -axis accounting for most of the volume change. Bütschliite undergoes a phase transition to a monoclinic C 2/ m structure at around 6 GPa, mirroring polymorphism within isostructural borates. A fit to the compression data of the monoclinic phase yields $${V}_{0}=322.2$$ V 0 = 322.2 Å 3 $$,$$ , $${K}_{0}=24.8$$ K 0 = 24.8 GPa and $${K}_{0}^{\prime}=4.0$$ K 0 ′ = 4.0 using a third order fit; the ability to access different compression mechanisms gives rise to a more compressible material than the low-pressure phase. In particular, compression of the C 2/ m phase involves interlayer displacement and twisting of the [CO 3 ] units, and an increase in coordination number of the K + ion. Three more phase transitions, at ~ 28, 34, and 37 GPa occur based on the Raman spectra and powder diffraction data: these give rise to new [CO 3 ] bonding environments within the structure.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pulsed electric current joining of oxide-dispersion-strengthened austenitic steels

The solid-state joining of oxide-dispersion-strengthened (ODS) austenitic steels was achieved using a pulsed electric current joining (PECJ) process. Microstructures of the austenitic grain structures and oxide dispersions in the joint areas were characterized using electron microscopy. Negligible grain growth was observed in austenitic grain structures, while slight coarsening of oxide dispersions occurred at a short holding time. The mechanisms of the PECJ process may involve three steps that occur simultaneously, including the sintering of mechanical alloying powders in the bonding layer, formation of oxide dispersions, and bonding of the mechanical alloying powders with the base alloy. The high hardness and irradiation resistance of ODS alloys were retained in the joint areas. This research revealed the fundamental mechanisms during the PECJ process, which is beneficial for its potential applications during the advanced manufacturing of ODS alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Synthesis and characteristics of porous ceramic tubes: a comparison of centrifugal casting and cold isostatic pressing methods

Short porous ceramic tubes in small quantities are needed for membrane-related research and development efforts and can be synthesized by centrifugal casting (CC) or cold isostatic pressing (CIP) methods. Here, this work evaluates the characteristics of porous ceramic tubes prepared by both methods and provides a strategy for selecting the proper method for ceramic tube fabrication, depending on its application. Samarium-doped ceria (SDC) with an average crystallite size of 10 nm was synthesized by a citrate method and used to make porous SDC tubes by the CC and CIP methods under different conditions. Porous SDC tubes were prepared from an aqueous suspension of the SDC powder with polyvinyl alcohol (PVA) using a cylindrical metallic mold, centrifugated at 4000–6000 rpm, followed by sintering in 1200–1500 °C. SDC tubes were also made by the CIP method from the SDC powder placed inside a cylindrical rubber bag followed by isostatic compression at 1379 bar. The pore structure of the SDC tubes was characterized by helium permeation and liquid nitrogen Archimedes method. Due to high compression pressure giving a low porosity green tube, the CIP method with lower sintering temperature produces SDC tubes with much lower porosity and average pore size and similar tortuosity compared to the CC methods. The CIP method should be used to prepare low porosity or dense ceramic tubes, and the CC method should be used for preparing high-porosity ceramic tubes or tubes with pore gradient tube wall.

36 MATERIALS SCIENCE↗
DOE OSTI2021

X-ray diffraction, differential scanning calorimetry and evolved gas analysis of aged plutonium tetrafluoride (PuF4)

A 30 year-old PuF4 sample consisting of brown powder (PuF4-b) and pink granules (PuF4-p) was analyzed. X-ray difraction shows the bulk is comprised of three compounds: PuF4, PuO2, and PuF4·1.6H2O. Broadening of PuF4 XRD peaks suggests possible a-damage. After annealing at 650 °C, crystalline PuF4 and PuO2 remain. Thermogravimetric analysis and diferential scanning calorimetry—with simultaneous evolved gas analysis—of the separated PuF4-p and PuF4-b components reveal a distinct sequence of reactions. Dehydration occurs between~90 and 300 °C. Exothermic annealing of the a-damage occurs in two stages: at 350–355 °C and at 555–558 °C. Hydrofuoric acid, fuorine and helium desorb during the frst exotherm. Above 700 °C, PuF4 reacts with PuO2, resulting in oxygen release and mass loss.

PuF4, dsc, differential scanning calorimetry, plut↗
DOE OSTI2022

Thermal behavior of ammonium octafluorodirhenate(III)

The thermal behavior of (NH 4 ) 2 [Re 2 F 8 ]·2H 2 O salt was studied in the temperature range 150–700 °C under flowing nitrogen gas. The decomposition products were studied by powder X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. Results are consistent with the formation of (NH 4 ) 2 [Re 2 F 8 ] salt at 150 °C, amorphous rhenium metal at 300 and 400 °C, and crystalline rhenium metal at 500 and 700 °C. A mechanism of formation of rhenium metal from (NH 4 ) 2 [Re 2 F 8 ]·2H 2 O was proposed. Here, the effect of crystallite size and lattice strain was evaluated at 500 and 700 °C from powder XRD peak broadenings using both Williamson–Hall and the modified Scherrer methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Investigation of the Effect of Chrome and Nickel Concentrations During Two-Piston Splat Quenching of Austenitic Stainless Steels

For solidification rates at or near equilibrium solidification conditions the effects of chrome (Cr) and nickel (Ni) on stainless steel solidification modes and microstructures are well detailed. However, fusion-based additive manufacturing (FBAM) processes that rely on faster, more rapid solidification rates call for a more in-depth understanding of the effects of rapid solidification on the solidification behavior and how these change with variations in alloy composition. Eleven custom stainless steel (SS) alloys with unique compositions based on 316L were made using targeted alloying element additions to generate feedstock with Cr/Ni eq ratios ranging from 0.9 to 2.1. Two-piston splat quenching (SQ) was used to produce rapid solidification conditions similar to those achieved in powder bed fusion processes in a fraction of the time and cost of traditional methods. Employing heat transfer simulations, SEM, TEM, and STEM characterization techniques, the SQ process was found to consistently produce solidification rates estimated to be between ~ 0.4 and 1.6 m/s. Five unique solidification microstructures were identified within the rapidly solidified SQ samples (primary austenite, massively transformed ferrite to austenite, primary austenite and massively transformed ferrite to austenite, primary ferrite, and primary ferrite and massively transformed ferrite to austenite). Both the primary ferrite solidification mode and primary ferrite phase were found to form at lower Cr/Ni eq values than previously predicted. SQ samples with compositions that were within the compositional specifications for 316L SS, an alloy which is commonly used in FBAM processes, demonstrated a wider range of potential solidification modes and microstructures that could form at rapid solidification rates than expected. Finally, by using SQ as a means to simulate rapid solidification conditions similar to those observed in FBAM processes, potential new alloy compositions can be screened faster and more cost effectively than purchasing and running test batches of the metallic powder.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Creep Deformation and Damage Mechanisms in an Advanced High-Temperature Additively Manufactured Nickel-Base Superalloy

Abstract This research investigates the processing–structure–properties–performance relationship in a novel nickel-base superalloy, ABD ® -900AM, designed for extreme environments. Specifically tailored for additive manufacturing (AM), ABD ® -900AM maintains mechanical integrity at high temperatures and is comparable to other nickel-based superalloys with a 30–40% gamma-prime volume fraction. A comprehensive study was conducted using laser-beam powder bed fusion and electron-beam powder bed fusion methods. Factors such as heat treatment, porosity, build orientation, and hot isostatic pressing were evaluated to understand their effects on microstructure and mechanical performance. Microstructural characterization revealed significant differences in grain size and orientation across build processes and heat treatments. High-temperature mechanical testing indicated that grain size, heat treatment, and orientation significantly influence creep behavior. A super-solvus heat treatment led to recrystallization and grain growth, significantly improving creep properties compared to a near-solvus heat treatment. Various creep mechanisms were identified across different conditions, and creep rupture models were developed for each build process. Post-test microstructural analysis showed grain boundary damage, with differences in creep cavitation morphology under varying stress conditions. It was shown that MC carbides grow at the expense of gamma-prime near grain boundaries, leading to precipitate-free zones in specimens tested at higher temperatures. This study fills a significant gap in fundamental research by offering a deeper insight into the high-temperature mechanical behavior of additively manufactured nickel-base superalloys. It also explores critical research questions regarding the role of carbides and the significance of heat treatment. The insights gained enhance confidence in the industry adoption of ABD ® -900AM and similar alloys for high-temperature applications, bridging the knowledge gap and supporting the development of reliable AM processes for extreme environments.

Bridges, Alex (ORCID:000000030338759X)↗
DOE OSTI2025

Mechanical Characteristics of Additively Manufactured ODS 316L and 316H Alloys with and Without Post-build Processing

This research aims to explore an accelerated development path for oxide dispersion-strengthened (ODS) alloys by integrating additive manufacturing (AM) technologies with recent advances in ODS materials and traditional manufacturing methods. Novel AM and post-build processing routes have been developed for ODS austenitic alloys, specifically Fe-Cr-Ni alloys like 316L and 316H. Electron microscopy and mechanical characterizations were conducted to evaluate the effects of process variables on microstructure and properties, aiming for an economically feasible route property optimization. Traditionally, ODS alloy production involves multi-day high-energy mechanical milling of alloy powder with yttria (Y 2 O 3 ) followed by powder consolidation via extrusion or other methods and additional thermomechanical processing (TMP) for property control. Here, to address these challenges associated with this complex and costly approach, we propose exploring alternative, cost-effective processing routes focusing on AM and traditional TMP methods. The new ODS alloy processing routes have achieved up to a 400% increase in yield strength and a 60% increase in ultimate tensile strength compared to wrought stainless steels while still maintaining significant ductility and fracture toughness. This paper details the novel and economical AM-based processing routes for ODS austenitic alloys, combined with post-build TMPs, and discusses the mechanical and microstructural characteristics of the developed materials.

Byun, Thak Sang [Oak Ridge National Laboratory (OR↗
DOE OSTI2024

Composite coatings from polycarbosilane derived SiC and Al/SiC cermet active fillers as protective barriers against steel corrosion

Stainless steel is used throughout the world as a structural material. However, it undergoes corrosion damage when exposed to extremely corrosive media, such as the marine environment. An alternative to solve this problem lies in the development of coatings that can withstand extreme conditions but also be easily deposited with inherently corrosion-resistant materials such as silicon carbide (SiC). The present study shows a simple method to produce Al/SiC cermet powders by attrition milling. The resulting cermet powders with a metallic matrix and hemispherical morphology, were employed as fillers in polycarbosilane (PCS) solutions that were sprayed on A304 stainless steel substrates. Al/SiC composite coatings were produced after heating the sprayed suspensions at 700 °C for 1 h in Ar atmosphere. The resulting composite coatings exhibited low surface energies (< 35 mN/m), water contact angles of 53°, and adhesion strength of up to 30 MPa. Finally, corrosion tests were performed in a cyclic corrosion test chamber, showing that these coatings effectively reduced the corrosion rate of stainless steel by 87%, reaching corrosion rate values of 0.007 g/cm 2 year.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Predicting Sintering Window of Binder Jet Additively Manufactured Parts Using a Coupled Data Analytics and CALPHAD Approach

Batch-to-batch variation in powder compositions for binder jet additive manufacturing (BJAM) can significantly deter defining an “ideal” sintering window for a given alloy. One way to overcome the problem is by running sintering experiments at various temperatures for each batch of the powder. However, such an approach increases the time required to achieve large-scale production of parts. The predictive capabilities of computational thermodynamic tools like CALPHAD can be leveraged to overcome the challenge, especially for binder jet additive manufacturing, since the process occurs under near-equilibrium conditions. However, calculating the sintering window using CALPHAD can be computationally expensive, considering many possible feedstock compositions within “specification”. Here, we generate high throughput CALPHAD data for nickel-based superalloys to develop machine learning models to predict the sintering window rapidly. The predictive capability of the models has been validated using published results on BJAM of Inconel 718 and 625. Further, validated models are lightweight and can be deployed in an industrial setting to get sintering window in an accelerated manner.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Coaxial color channel focus evaluation to estimate standoff height in directed energy deposition additive manufacturing

Directed energy deposition (DED) is an additive manufacturing process that is being rapidly adopted by industry and is well suited for the fabrication of complex components in a variety of metal alloys. In laser cladding systems such as DED, powder is blown in a stream to a metal substrate coincident with a laser necessary to deposit molten metal with 3D spatial control. The focus of both the laser and the powder stream are crucial, and best deposition occurs at a predetermined standoff height between the build surface and the print head. Generally, no monitoring of this distance is implemented in commercial DED systems. Due to potential over or under building, the standoff height often changes over time but tends to self-correct. However, inexpensive and minimally intrusive methods to identify optimal standoff are required to provide real-time control to maintain the optimal distance. The present work explores the quantification of the focus of the three-color channels of a coaxial camera to determine the standoff height. An experiment was performed in which a 254 mm wall is built and the standoff height, initially 5.0 mm below the optimal position, was then intentionally increased every 25.4 mm of wall length by an amount of 1.0 mm to a final position 7.0 mm above optimal. Computer vision is demonstrated to monitor the amount of focus in each color band and estimate standoff distance. Finally, a response can be calculated in under 40 ms using simple hardware and can work in most laser-based DED systems.

36 MATERIALS SCIENCE↗