Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

Association of residential energy efficiency retrofits with indoor environmental quality, comfort, and health: A review of empirical data

This paper reviews empirical data from evaluations of the influence of residential energy efficiency retrofits on indoor environmental quality conditions and self-reported thermal comfort and health. The data were extracted from 36 studies described in 44 papers plus two reports. Nearly all reviewed studies were performed in Europe or United States. Most studies evaluated retrofits of homes with low-income occupants. Indoor radon and formaldehyde concentrations tended to increase after retrofits that did not add whole-house mechanical ventilation. Study-average indoor concentrations of nitrogen dioxide and volatile organic compounds other than formaldehyde increased and decreased with approximately equal frequency. Average indoor temperatures during winter typically increased after retrofits, usually by less than 1.5 °C. Dampness and mold, usually based on occupant's reports, almost always decreased after retrofits. Subjectively reported thermal comfort, thermal discomfort, non-asthma respiratory symptoms, general health, and mental health nearly always improved after retrofits. For asthma symptoms, the evidence of improvement slightly outweighed the evidence of worsening. There was insufficient evidence to determine whether changes in thermal comfort and health outcomes varied depending on the type of energy efficiency retrofit. The published research has numerous limitations including a lack of data from retrofits in warm-humid climates and minimal data on changes in objective health outcomes. Suggestions for future research are provided.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Test beam study of SiPM-on-tile configurations

Light yield and spatial uniformity for a large variety of configurations of scintillator tiles were studied. The light from each scintillator was collected by a Silicon Photomultiplier (SiPM) directly viewing the produced scintillation light (SiPM-on-tile technique). The varied parameters included tile transverse size, tile thickness, tile wrapping material, scintillator composition, and SiPM model. Furthermore, these studies were performed using 120 GeV protons at the Fermilab Test Beam Facility. External tracking allowed the position of each proton penetrating a tile to be measured. The results were compared to a GEANT4 simulation of each configuration of scinitillator, wrapping, and SiPM.

47 OTHER INSTRUMENTATION↗

Hydrogen Sulfide Passivation for p-Type Passivated Emitter and Rear Contact Solar Cells

This work reports on the application of sulfur (S)-passivation to passivated emitter and rear contact (PERC) solar cells. The emitter surface was passivated by hydrogen sulfide (H 2 S) gas phase reaction and capped by a hydrogenated amorphous silicon nitride (a-SiN x :H) layer. The sulfur passivation on a symmetrically n + diffused emitter is shown to lead to an emitter saturation current density (J 0n+ ) of 30 fA/cm 2 at R sheet,n+ ≈ 100 Ω/sq. The application of S-passivation to the emitter surface in the PERC cell structure, with the rear surface passivated by an aluminum oxide (Al 2 O 3 )/a-SiN x :H stack, showed a promising implied open-circuit voltage (iV OC ) of 686 mV before metallization. This iV OC was higher than that for the a-SiN x :H or SiO 2 /a-SiN x :H passivated emitter surfaces (675 and 674 mV, respectively) on PERC cells processed in the same run. However, a significant drop in cell V OC is observed for the S-passivated PERC cell after the completion of device fabrication with laser patterning, screen-printed metal contact deposition, and firing. Nonetheless, an efficiency of ~20% and a V OC of ~650 mV was achieved with an emitter surface passivated by sulfur. We identified that the 760°C contact firing process degrades the S-passivation quality. Furthermore, the surface morphology was studied, and a detailed surface analysis was performed to study the causes of the S-passivated surface degradation.

14 SOLAR ENERGY↗

diffReplication - An Energy-Aware Fault Tolerance Model for Silent Error Detection and Mitigation in Heterogeneous Extreme-scale Computing Environment

At extreme scale, the frequency of silent errors – a class of errors that remain undetected by low-level error detection mechanisms – increases significantly with the computational complexity of the application and the scale of the computing infrastructure. As hardware and software advances are made to usher in the next scientific era of computing, developing new approaches to mitigate the impact of silent errors remains a challenging problem. In this work, we propose an energy-aware fault-tolerance model, referred to diffReplication to overcome silent errors. In the proposed model, the main process is associated with one replica that executes at the same rate as the main process, and one diffReplica that is executed at a fraction of the main process' execution rate. If the main and its replica reach consensus at the end of a computation phase, the state of the diffReplica is updated and computation is resumed. If the synchronization attempt results in a disagreement, however, the diffReplica increases its execution speed to complete the computation and quickly reach the synchronization barrier. Assuming a single error over any given synchronization interval, a majority voting is used to reach consensus and tolerate silent errors. To further enhance its performance, diffReplication is augmented with speculative execution, whereby the main or its fast replica is selected to continue execution without waiting for the diffReplica. The selection process is based on the previous behaviour of the main and its replica. A performance analysis study is carried out to assess the performance of diffReplication, in terms of the energy saving and time-to-completion reduction achieved by the diffReplication scheme. The experiment shows that speculative execution reduces the time to completion with additional energy, and dynamic decision-making balances the energy consumption and time to completion.

97 MATHEMATICS AND COMPUTING↗

Feasibility Study of Economics and Performance of Solar Photovoltaics at the Former St. Marks Refinery in St. Marks, Florida

This report presents the results of an assessment of the technical and economic feasibility of deploying a photovoltaics (PV) system on a brownfield site in St. Marks, Florida. The site was assessed for possible PV installations. The cost, performance, and site impacts of different PV options were estimated. The economics of the potential systems were analyzed using an electric rate of $0.08/kWhand incentives offered in the State of Florida and from the two accessible utilities, Progress Energy and the City of Tallahassee. According to the site production calculations, the most cost-effective system in terms of return on investment is the fixed-tilt thin film technology. The report recommends financing options that could assist in the implementation of such a system.

14 SOLAR ENERGY↗

Ion-optical and Associated Magnet Feasibility Study of a High Rigidity Spectrometer

Ion-optical and magnet-feasibility studies were performed for the High Rigidity Spectrometer (HRS) at the Facility for Rare Isotope Beam (FRIB). The High Rigidity Spectrometer (HRS) will be the centerpiece experimental tool of the Facility for Rare-Isotope Beams (FRIB) fast-beam program The high magnetic rigidity of the HRS (8 Tm) will match the rigidities at which rare-isotope production yields at the FRIB fragment separator are maximum across the entire chart of nuclei and enable experiments with the most neutron-rich nuclei available at FRIB. Gain factors in luminosity of up to two orders of magnitude are achievable compared to running with existing spectrometers, which have a maximum rigidity of 4 Tm. The ion-optical studies were performed to ensure that the layout and properties meet the requirements for the scientific program envisioned for and articulated by the FRIB user community. Based on the ion-optical studies, magnet-feasibility studies were carried out to ensure that the magnets required for the HRS meet these requirements and can be constructed. The results of the ion-optical and magnet-feasibility studies form the basis of the pre-conceptual design for the HRS.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Review of Heavy Flavor Physics at the Tevatron

The D0 and CDF detectors at the Fermilab Tevatron have each accumulated more that 9 fb{sup -1} of integrated luminosity. The corresponding large datasets enable the two experiments to perform unprecedented studies of heavy flavor hadron properties. We present recent D0 and CDF measurements, focusing on rare decays and CP violation in B-meson decays. Flavor Physics probes new phenomena by either searching for small deviations from the Standard Model (SM) based theoretical predictions or by measuring quantities which are highly suppressed within the SM. Searching for small deviations from the SM are performed using large strange, charm or bottom hadron samples, mostly by kaon experiments of B factories. Measurements of highly suppressed quantities, such as CP violation phases and asymmetries in the neutral B{sub s}-meson system or searches for rare B decays, are performed with the hope that new physics effects would be large enough to significantly affect the measured quantities and so, lead to observations of deviations from the SM expectations. The D0 and CDF detectors at the Fermilab Tevatron have each accumulated more that 9 fb{sup -1} of integrated luminosity. The corresponding large datasets enable the two experiments to perform unprecedented studies of heavy flavor hadron properties. We present recent D0 and CDF measurements, focusing on rare decays and CP violation in B-meson decays.

43 PARTICLE ACCELERATORS↗

Feasibility Study of Economics and Performance of Solar Photovoltaics at the Refuse Hideaway Landfill in Middleton, Wisconsin

This report presents the results of an assessment of the technical and economic feasibility of deploying a photovoltaics (PV) system on a brownfield site at the Refuse Hideaway Landfill in Middleton, Wisconsin. The site currently has a PV system in place and was assessed for further PV installations. The cost, performance, and site impacts of different PV options were estimated. The economics ofthe potential systems were analyzed using an electric rate of $0.1333/kWh and incentives offered by the State of Wisconsin and by the serving utility, Madison Gas and Electric. According to the site production calculations, the most cost-effective system in terms of return on investment is the thin-film fixed-tilt technology. The report recommends financing options that could assist in theimplementation of such a system.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Representation of Global Climate Change in Performance Assessment Models for Disposal of Radioactive Waste - 17183

Evolving concepts of global climate change that include impacts of anthropogenic greenhouse gases require reassessment of conventional conservative approaches in performance assessment studies that assume cold and wet future glacial climates. Global paleo-climate data for the Quaternary (past 2 million years) show saw-tooth patterns (temperature/proxy temperature data versus time) of glacial and interglacial intervals accompanied by cyclical changes in the atmospheric content of CO{sub 2} (low contents during glacial cycles and higher contents during interglacial cycles). These cycles are correlated with changes in the earth's orbital configurations (Milankovitch cycles) but require nonlinear linkages with additional climate-forcing components to reproduce past glacial and interglacial transitions. The earth is currently in an interglacial period and the timing of the inception of the next glacial period is critically important for forecasting future climate states. Climate modeling studies coupling Milankovitch cycles with variable atmospheric CO{sub 2} content demonstrate conclusively that the earth is very unlikely to return to a glacial state when CO{sub 2} concentrations remain above pre-industrial levels (∼ 280 parts per million; current levels exceed 400 parts per million). A return to pre-industrial concentrations will likely require > 50,000 years and may require hundreds of thousands of years even if current emissions were to drop dramatically. The most likely scenario for the future global climate is persistence of the current interglacial period with variable but progressively increasing temperatures. Performance assessments need to revise site-specific evaluations of future climate assuming global warming within a prolonged interglacial period with increased probability of extreme weather events. Four radioactive waste disposal sites are illustrated that currently incorporate or will incorporate revised current climate concepts in modeling studies for performance assessments. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Improving cryogenic deuterium–tritium implosion performance on OMEGA

A flexible direct-drive target platform is used to implode cryogenic deuterium–tritium (DT) capsules on the OMEGA laser [Boehly et al., Opt. Commun. 133, 495 (1997)]. The goal of these experiments is to demonstrate ignition hydrodynamically equivalent performance where the laser drive intensity, the implosion velocity, the fuel adiabat, and the in-flight aspect ratio (IFAR) are the same as those for a 1.5-MJ target [Goncharov et al., Phys. Rev. Lett. 104, 165001 (2010)] designed to ignite on the National Ignition Facility [Hogan et al., Nucl. Fusion 41, 567 (2001)]. The results from a series of 29 cryogenic DT implosions are presented. The implosions were designed to span a broad region of design space to study target performance as a function of shell stability (adiabat) and implosion velocity. Ablation-front perturbation growth appears to limit target performance at high implosion velocities. Target outer-surface defects associated with contaminant gases in the DT fuel are identified as the dominant perturbation source at the ablation surface; performance degradation is confirmed by 2D hydrodynamic simulations that include these defects. A trend in the value of the Lawson criterion [Betti et al., Phys. Plasmas 17, 058102 (2010)] for each of the implosions in adiabat–IFAR space suggests the existence of a stability boundary that leads to ablator mixing into the hot spot for the most ignition-equivalent designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Probing Selected Morphological Models of Hydrated Nafion Using Large-Scale Molecular Dynamics Simulations

Atomistic molecular dynamics simulations were performed to study hydrated Nafion systems large enough (approximately 2 million atoms, approximately 30 nm box length) to directly observe several hydrophilic domains at the molecular level. These systems consisted of six of the most significant and relevant morphological models of Nafion to-date: (1) the cluster-channel model, (2) the parallel cylinder model, (3) the local order model, (4) the lamellar model, (5) the rod network model, and (6) a "random" model that does not directly assume any particular geometry, distribution, or morphology. Each system was initially built to closely approximate the proposed hydrophilic cluster structure in a given model. Molecular dynamics simulations were then used to observe resulting changes from and behavior of the assumed initial configurations. These simulations revealed fast intercluster "bridge" formation and network percolation in all models. Sulfonate groups were found inside these bridges and played a significant role in percolation. Sulfonates also strongly aggregated around and inside clusters. Cluster surfaces were analyzed to study the hydrophilic-hydrophobic interface. Interfacial area and cluster volume significantly increased during the simulations, and radial distribution functions and structure factors were also calculated. All nonrandom models clearly exhibited the characteristic experimental scattering peak, underscoring the insensitivity of this measurement to hydrophilic domain structure and highlighting the need for future work to clearly distinguish morphological models of Nafion.

Knox, Craig K.↗

Studying impacts of communication system performance on dynamic stability of networked microgrid

The development of smart grid technologies has resulted in increased interdependence between power and communication systems. Many of the operations in the existing power system rely on a stable and secured communication system. For electrically weak systems and time‐critical applications, this reliance can be even greater, where a small degradation in communication performance can degrade system stability. However, despite inter‐dependencies between power and communication systems, only a few studies have investigated the impacts of communication system performance on power system dynamics. This study investigates the dependencies of power system dynamics operations on a communication system performance. First, a detailed, dynamic networked microgrid model is developed in the GridLAB‐D simulation environment, along with a representative multi‐traffic, multi‐channel, multi‐protocol communication system model, developed in the network simulator (ns‐3). Second, a hierarchical engine for large‐scale infrastructure co‐simulation framework is developed to co‐simulate microgrid dynamics, its communication system, and a microgrid control system. The impact of communication system delays on the dynamic stability of networked microgrids is evaluated for the loss of generation using three use‐cases. While the example use‐cases examine microgrid applications and the impact to resiliency, the framework can be applied to all levels of power system operations.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Progress toward hydro-equivalent ignition in OMEGA direct-drive DT-layered implosions

Considerable progress has been made in deuterium-tritium-layered implosion experiments on the OMEGA Laser System, bringing the prospects for thermonuclear ignition in direct-drive configurations with megajoule-class lasers closer to reality. Doing so has required navigating the balance between improved 1D performance and multidimensional stability. Using statistical modeling based on over 350 cryogenic implosions to identify various degradation mechanisms, and combined with multidimensional simulations and experimental techniques such as target offsets to combat residual flows, core conditions have repeatably been achieved that extrapolate to the burning-plasma state when scaled to 2.15 MJ of symmetric laser illumination. Using high implosion velocities (⁠> 450 km/s) and moderately high adiabats (⁠~5⁠), these experiments produced record-high scaled Lawson parameters in direct drive equal to 89 ± 2% of that required for ignition with expected yields of up to 1.5 ± 0.2 MJ. To improve these results still further, focused physics studies are performed to improve physics understanding and identify routes to even greater performance. Recent studies include investigations into the impact of mounting features, laser imprint, reduced fuel temperatures, and greater on-target intensities through subscale experiments. This manuscript gives a summary of the cryogenic direct-drive program on the OMEGA laser, including routes taken to achieve the current best performance, the status of recent focused physics investigations, and future designs—such as target solutions to laser imprint and reducing vapor density to increase convergence—that are expected lead to the demonstration of hydro-equivalent ignition on OMEGA.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Improving Representation of Convective Transport for Scale-Aware Parameterization – Part I: Convection and Cloud Properties Simulated with Spectral Bin and Bulk Microphysics

The ultimate goal of this study is to improve representation of convective transport by cumulus parameterization for meso-scale and climate models. As Part I of the study, we perform extensive evaluations of cloud-resolving simulations of a squall line and mesoscale convective complexes in mid-latitude continent and tropical regions using the Weather Research and Forecasting (WRF) model with spectral-bin microphysics (SBM) and with two double-moment bulk microphysics schemes: a modified Morrison (MOR) and Milbrandt and Yau (MY2). Compared to observations, in general, SBM gives better simulations of precipitation, vertical velocity of convective cores, and the vertically decreasing trend of radar reflectivity than MOR and MY2, and therefore will be used for analysis of scale-dependence of eddy transport in Part II. The common features of the simulations for all convective systems are (1) the model tends to overestimate convection intensity in the middle and upper troposphere, but SBM can alleviate much of the overestimation and reproduce the observed convection intensity well; (2) the model greatly overestimates radar reflectivity in convective cores (SBM predicts smaller radar reflectivity but does not remove the large overestimation); and (3) the model performs better for mid-latitude convective systems than tropical system. The modeled mass fluxes of the mid latitude systems are not sensitive to microphysics schemes, but are very sensitive for the tropical case indicating strong microphysics modification to convection. Cloud microphysical measurements of rain, snow and graupel in convective cores will be critically important to further elucidate issues within cloud microphysics schemes.

Fan, Jiwen↗

Advancing the STS Neutron Moderator Design with an Automated Optimization Workflow and Unstructured Mesh Modeling

With the Second Target Station approaching its final design phase, a detailed neutronics evaluation of its critical components is necessary. Optimizing the dimensions of the two cold-source moderators that are at the heart of this facility presents a multi-objective optimization problem for which an accurate geometric description is crucial. We have applied a fully automated optimization workflow in which a detailed unstructured mesh geometry is automatically generated with Attila4MC, starting from a parametrized CREO geometry followed by preprocessing with SpaceClaim. With this geometry, a MCNP run is performed to calculate the brightness metrics, which are subsequently provided to the optimization algorithm in DAKOTA that provides new parameters and drives the optimization loop until convergence. In this paper, we show the results of the analysis that are used for the final design of the cylindrical and tube moderator. The optimization simulations provide a refinement to and confirmation of the conclusions of the previous design iteration. Additional to the optimization, a sensitivity study is performed to study the effect of minor geometry changes, which is important for the final engineering design. In conclusion, with these studies, we demonstrate that the automated workflow and high-fidelity unstructured mesh modeling are efficient tools for a thorough design evaluation.

DAKOTA↗

Two-Stage Gauss-Seidel Preconditioners and Smoothers for Krylov Solvers on a GPU Cluster: Preprint

Gauss-Seidel (GS) relaxation is often employed as a preconditioner for a Krylov solver or as a smoother for Algebraic Multigrid (AMG). However, the requisite sparse triangular solve is difficult to parallelize on many-core architectures such as graphics processing units (GPUs). In the present study, the performance of the sequential GS relaxation based on a triangular solve is compared with two-stage variants, replacing the direct triangular solve with a fixed number of inner Jacobi-Richardson (JR) iterations. When a small number of inner iterations is sufficient to maintain the Krylov convergence rate, the two-stage GS (GS2) often outperforms the sequential algorithm on many-core architectures. The GS2 algorithm is also compared with JR. When they perform the same number of ops for SpMV (e.g. three JR sweeps compared to two GS sweeps with one inner JR sweep), the GS2 iterations, and the Krylov solver preconditioned with GS2, may converge faster than the JR iterations. Moreover, for some problems (e.g. elasticity), it was found that JR may diverge with a damping factor of one, whereas two-stage GS may improve the convergence with more inner iterations. Finally, to study the performance of the two-stage smoother and preconditioner for a practical problem, these were applied to incompressible uid ow simulations on GPUs.

algebraic multigrid↗