SEARCH · Engineering Papers

Results for “module temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Combined electrocoagulation-microfiltration-membrane distillation for treatment of hydraulic fracturing produced water

Hydraulic fracturing flowback and produced water is a highly impaired wastewater containing dissolved salts polar and non-polar organic compounds, oil and surfactants. Here a combined electrocoagulation - microfiltration – membrane distillation process has been used to treat this wastewater. Electrocoagulation followed by microfiltration was used to pretreat the wastewater prior membrane distillation. The initial total dissolved solids (TDS) concentration was extremely high being 245,300 mg L -1 . After electrocoagulation, the total organic carbon (TOC) was reduced from 120 mg L -1 to 64 mg L -1 . Tangential flow microfiltration using a 0.1 μm pore size polyethersulfone membrane was used to separate the particulate matter after electrocoagulation and to further reduce the TOC to 44 mg L -1 . Membrane distillation was used to desalinate the pretreated produced water resulting in a high quality treated water (TDS of 56 mg L -1 and TOC 1 mg L -1 ). Three membranes with very different surface morphology were used: commercially available polyvinylidene fluoride, electrospun poly(vinylidene fluoride-co-hexafluoropropylene) nanofibers and multiwalled carbon nanotube coated polytetrafluoroethylene. The TDS in the retentate increased to over 350,000 mg L -1 . During membrane distillation, the temperature of the feed tank was maintained at 36 °C while the feed entered the module at 60 °C in order to minimize scaling on the membrane. The surface properties of an ideal membrane that is resistant to wetting and provides high flux is likely to depend on the TDS and properties of the wastewater.

42 ENGINEERING↗

DOE OSTI2026

Bound Exciton Complexes in Near-Infrared Emitting Quantum Shells

Near-infrared (NIR) light sources based on colloidal semiconductor nanocrystals (NCs) represent a scalable, low-cost alternative to epitaxial semiconductor platforms. However, their performance remains hindered by rapid Auger recombination, a problem that is particularly pronounced in narrow-bandgap materials. Here, we report on CdS/HgS/CdS and CdS/HgCdSe/ ZnS quantum shells (QSs), a class of spherical quantum wells specifically engineered for a suppression of nonradiative Auger processes. Fabricated QSs exhibit tunable NIR emission with photoluminescence quantum yields reaching ∼60% below 1000 nm and up to 30% near 1300 nm. Optical gain and stimulated emission were observed in CdS/HgS/CdS QSs. In contrast, CdS/HgCdSe/ZnS QSs displayed a photoinduced absorption in lieu of optical gain despite demonstrating a comparatively stronger Auger suppression. Transient absorption spectroscopy revealed that this phenomenon arises from the formation of bound multiexciton complexes that induce long-lived sub-bandgap multiexciton states. The observation of such bound excitonic clusters at room temperature offers a pathway toward nonlinear NIR photonic phenomena, including biexciton−exciton cascade emission, optical modulation, and singleexciton gain.

Auger recombination↗

DOE OSTI2025

Continuous Encodable Reshaping of Gold Nanocrystals through Facet Modulation

Shape control of nanocrystals (NCs) is crucial for tuning their assembly behavior and functional properties, yet the precise manipulation of facet composition remains challenging. Here, we present a nanocrystal reshaping strategy to control and modulate the facets of gold (Au) NCs. Our one-pot approach, conducted at room temperature, requires only initial Au NCs, Au 3+ ions, and surfactants, distinguishing it from conventional reduction-mediated “etching-and-regrowth” methods. Detailed structural studies using electron microscopy, small-angle X-ray scattering (SAXS), and UV−vis spectroscopy reveal the surfactant-encoded pathway for NC transformation from shaped particles to spheres and then into various polyhedral shapes while preserving the individual particles' volume. The proposed reshaping mechanism involves the dissolution of surface Au atoms into Au + complexes in the presence of Au 3+ and surfactant, followed by surfactant-guided redeposition and formation of facets with different atomic planes. Using the ethanol oxidation reaction (EOR) as a probe, we observe a quasi-linear decrease in onset potential and an increase in activity with increasing {100} facet exposure. This work broadens synthetic strategies by offering precise NC reshaping and facet control.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Encoding multistate charge order and chirality in endotaxial heterostructures

Abstract High-density phase change memory (PCM) storage is proposed for materials with multiple intermediate resistance states, which have been observed in 1 T -TaS 2 due to charge density wave (CDW) phase transitions. However, the metastability responsible for this behavior makes the presence of multistate switching unpredictable in TaS 2 devices. Here, we demonstrate the fabrication of nanothick verti-lateral H -TaS 2 /1 T -TaS 2 heterostructures in which the number of endotaxial metallic H -TaS 2 monolayers dictates the number of resistance transitions in 1 T -TaS 2 lamellae near room temperature. Further, we also observe optically active heterochirality in the CDW superlattice structure, which is modulated in concert with the resistivity steps, and we show how strain engineering can be used to nucleate these polytype conversions. This work positions the principle of endotaxial heterostructures as a promising conceptual framework for reliable, non-volatile, and multi-level switching of structure, chirality, and resistance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Thermal and Quantum Melting Phase Diagrams for a Magnetic-Field-Induced Wigner Solid

A sufficiently large perpendicular magnetic field quenches the kinetic (Fermi) energy of an interacting two-dimensional (2D) system of fermions, making them susceptible to the formation of a Wigner solid (WS) phase in which the charged carriers organize themselves in a periodic array in order to minimize their Coulomb repulsion energy. In low-disorder 2D electron systems confined to modulation-doped GaAs heterostructures, signatures of a magnetic-field-induced WS appear at low temperatures and very small Landau level filling factors ($\textit{ν}$ ≃ 1/5). In dilute GaAs 2D hole systems, on the other hand, thanks to the larger hole effective mass and the ensuing Landau level mixing, the WS forms at relatively higher fillings ($\textit{ν}$ ≃ 1/3). Here we report our measurements of the fundamental temperature vs filling phase diagram for the 2D holes’ WS-liquid thermal melting. Moreover, via changing the 2D hole density, we also probe their Landau level mixing vs filling WS-liquid quantum melting phase diagram. In this work, we find our data to be in good agreement with the results of very recent calculations, although intriguing subtleties remain.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Liquid-Cooled Heat Sink Optimization for Thermal Imbalance Mitigation in Wide-Bandgap Power Modules

Power semiconductor die placement on substrates used in high-power modules is generally optimized to minimize electrical parasitic (e.g., stray inductance, common-mode capacitance), taking into account the minimum spacing between semiconductor dies for thermal decoupling. The layout assumes sufficient heat spreading and transfer from dies to the cooling structure. Insulated metal substrate-based power module designs may lead to asymmetrical thermal resistance across the dies, which may cause significant temperature differences among the devices. Such unintentional thermal asymmetries can lead to oversizing the cooling system design or underusing the semiconductor power processing capability. This article proposes a thermal imbalance mitigation method that uses evolutionary optimized liquid-cooled heat sinks to improve the thermal loading among devices.

42 ENGINEERING↗

DOE OSTI2024

Performance Assessment of Photovoltaic Panels Using Impedance Spectroscopy

The goal of this project was to develop a technique for measuring internal characteristics of a PV module using light modulation under a fixed voltage bias while measuring the resulting alternating current. This technique, light-intensity modulated impedance spectroscopy (LIMIS), has the promise of detecting early signs of panel aging and degradation that could be used for example by solar farm operators to have early warnings to repair or replace panels to maintain reliability of the overall PV array. LIMIS would be complementary with the previously developed electrochemical impedance spectroscopy (EIS), which uses an alternating voltage applied electrically to a solar cell with a similar alternating current measurement. EIS has mostly been developed for individual PV cells rather than whole modules. The project was intended to assess what different information could be revealed by LIMIS, which may in some cases be more scalable to larger modules and potentially more practical to apply in field measurements without needing to electrically disconnect PV modules. We began with small 10 W PV modules and built a testbed capable of oscillating the light intensity with frequencies up to 50 kHz. In parallel, we built a large testbed for testing large 250 W PV modules. Meanwhile, we developed procedures for established measurement techniques: current–voltage (I–V), EIS, and electroluminescence (EL) imaging, where panels are subjected to forward bias while their infrared emission is recorded using a camera modified to be sensitive to IR wavelengths. In addition, we developed protocols for accelerated aging of PV modules in two ways. Thermal cycling from –40°C to +90°C simulates the diurnal temperature cycles on a rooftop. Mechanical stress by dropping a 227 g ball from a height of 1 m simulates damage such as that due to hail impacts.

14 SOLAR ENERGY↗

DOE OSTI2026

Hydrated Metal and Metal-Nitrate Complexes in Water: Full Lanthanide(III) Series plus Miscellaneous Metal Ions

This is a dataset of hydrated metal complexes and metal–nitrate hydrated complexes intended for public use, reproducibility, and downstream structural analysis. A key feature is coverage across the full lanthanide(III) series (La–Lu), enabling systematic comparisons of coordination motifs and bonding trends across the entire lanthanide sequence. In addition to the lanthanides, the dataset also includes other metal ions such as UO2(VI), Fe(II), and Fe(III). The dataset provides optimized geometries for hydrated and nitrate-containing hydrated complexes, together with representative ab initio molecular dynamics (AIMD) trajectories saved in standard XYZ formats. The accompanying NWChem input decks enable reproduction of the reported calculations and provide a starting point for extending the simulations to related coordination environments. Computationally, DFT calculations employ the B3LYP functional with DFT-D3BJ dispersion corrections and a COSMO continuum solvent model (dielectric constant 78.4) to represent solvation beyond the explicitly treated first hydration shell. AIMD simulations are performed with the NWChem qmd module at 298 K, integrating nuclear motion with the velocity-Verlet algorithm and controlling temperature using a Nosé–Hoover thermostat. Trajectories are approximately 4.8 ps in length and are used primarily to assess short-time stability of candidate coordination motifs, including (for lanthanides) differences between 8- versus 9-water coordination and comparisons between nitrate-bound and nitrate-free hydrated complexes.

Dinpajooh, Mohammadhasan [Pacific Northwest Nation↗

NASA NTRS1980

DOE/JPL advanced thermionic technology program

Accomplishments in the DOE program include: continuing stable output from the combustion life test of the one-inch diameter hemispherical silicon carbine diode (Converter No. 239) at an emitter temperature of 1730 K for a period of over 4200 hours; construction of four diode module completed; favorable results obtained from TAM combustor-gas turbine system analyses; and obtained a FERP work function of 2.3 eV with the W(100)-O-Zr-C electrode. JPL program accomplishments include: the average minimum barrier index of the last six research diodes built with sublimed molybdenum oxide collectors was 20 eV (WHK).

Source record↗

NASA NTRS1984

Advanced module development overview

Crystalline silicon solar power modules are examined for reliability and cost effectiveness. A goal of 12% solar energy conversion efficiency is considered feasible at a cost of 12/kWh, and a decision is made to limit consideration to float zone silicon wafer and dendritic web silicone modules. A preliminary module packaging configuration of glass/ethylene vinyl acetate/plastic film is selected. Anticipated module efficiency levels are 12.6% at 25 C and 11.5% at NOCT (Nominal Operating Cell Temperature).

Smokler, M. I.↗

NASA NTRS1984

The integration of bypass diodes with terrestrial photovoltaic modules and arrays

Bypass diodes are often required to limit the potential for reverse voltage 'hot-spot' heating in high voltage arrays or in arrays that undergo periodic operation near the short-circuit point. In addition, when properly applied, bypass diodes can minimize the effect of shadowing and various internal module failures on the array energy output. This paper discusses the mechanical and electrical integration of bypass diodes beginning with the array-level considerations which influence the selection of an implementation approach. Concepts for the mounting of these diodes, both internally within the module encapsulant and externally to the exposed rear surface of the module, are described. Factors affecting the reliability of bypass diodes, including the control of junction temperature through adequate heat sinking and the derating of reverse voltage, are discussed.

Shepard, N. F., Jr.↗

NASA NTRS1985

High-efficiency module design

Progress on the development of a high efficiency module is described. The effort includes development of high efficiency cells using crystalline silicon wafers from float zone silicon. Module-size cells, 53 sq cm in area, were fabricated with efficiency of 18%. Operating temperature reduction is also studied.

Spitzer, M. B.↗

NASA NTRS1986

Controlled environment life support system: Calcium-related leaf injuries on plants

Calcium related injuries to plants grown in controlled environments under conditions which maximize plant growth rates are described. Procedures to encourage movement of calcium into developing leaves of lettuce plants were investigated. The time course and pattern of calcium accumulation was determined to develop effective control procedures for this injury, termed tipburn. Procedures investigated were: (1) increasing the relative humidity to saturation during the dark period and altering root temperatures, (2) maximizing water stress during light and minimizing water stress during dark periods, (3) shortening the light-dark cycle lengths in combination with elevated moisture levels during the dark cycles, (4) reducing nutrient concentrations and (5) vibrating the plants. Saturated humidities at night increased the rate of growth and the large fluctuation in plant water potential encouraged calcium movement to the young leaves and delayed tipburn. Root temperature regulation between 15 and 26 C was not effective in preventing tipburn. Attempts to modulate water stress produced little variation, but no difference in tipburn development. Variations in light-dark cycle lengths also had no effect on calcium concentrations within developing leaves and no variation in tipburn development. Low concentrations of nutrient solution delayed tipburn, presumably because of greater calcium transport in the low concentration plants. Shaking of the plants did not prevent tipburn, but did delay it slightly.

Tibbitts, T. W.↗

NASA NTRS1990

TEMPUS: First results

The electromagnetic levitation facility, TEMPUS, developed by Dornier is designed to operate under microgravity conditions. Compared to terrestrial levitation, microgravity offers the possibility to melt and undercool in ultra high vacuum, thereby, providing an ultra clean environment. The technical concept of the TEMPUS facility was tested on two KC 135 flights and in the Texus 22 mission. Preparative investigations concerning the coil system and the heating and positioning efficiencies were carried out in the TEMPUS laboratory version. Furthermore, temperature-time profiles were determined under various boundary conditions. As a consequence of processing liquid metals under UHV, correct temperature measurement arises as the most critical problem. Experiences with experiments in the TEMPUS laboratory module show that due to the evaporation losses of the sample, the transmission of the CaF2 shielding windows changes drastically during the processing time. The investigation of the effect of contamination on pyrometry and the development of alternative evaporation shielding methods were initiated. During the second KC 135 flight, it was possible to heat up and melt an FeNi sample under He atmosphere. Oscillations of the molten sample, which were excited by switching out the magnetic heating field, could be detected and afterwards analyzed. From the frequency of these oscillations the surface tension of the sample material could be derived. The measurement of the surface tension and viscosity of an undercooled metal is proposed for TEMPUS on IML-2. This document is presented in view graph form.

Neuhaus, P.↗

NASA NTRS1993

Space Station thermal storage/refrigeration system research and development

Space Station thermal loading conditions represent an order of magnitude increase over current and previous spacecraft such as Skylab, Apollo, Pegasus III, Lunar Rover Vehicle, and Lockheed TRIDENT missiles. Thermal storage units (TSU's) were successfully used on these as well as many applications for ground based solar energy storage applications. It is desirable to store thermal energy during peak loading conditions as an alternative to providing increased radiator surface area which adds to the weight of the system. Basically, TSU's store heat by melting a phase change material (PCM) such as a paraffin. The physical property data for the PCM's used in the design of these TSU's is well defined in the literature. Design techniques are generally well established for the TSU's. However, the Space Station provides a new challenge in the application of these data and techniques because of three factors: the large size of the TSU required, the integration of the TSU for the Space Station thermal management concept with its diverse opportunities for storage application, and the TSU's interface with a two-phase (liquid/vapor) thermal bus/central heat rejection system. The objective in the thermal storage research and development task was to design, fabricate, and test a demonstration unit. One test article was to be a passive thermal storage unit capable of storing frozen food at -20 F for a minimum of 90 days. A second unit was to be capable of storing frozen biological samples at -94 F, again for a minimum of 90 days. The articles developed were compatible with shuttle mission conditions, including safety and handling by astronauts. Further, storage rack concepts were presented so that these units can be integrated into Space Station logistics module storage racks. The extreme sensitivity of spacecraft radiator systems design-to-heat rejection temperature requirements is well known. A large radiator area penalty is incurred if low temperatures are accommodated via a single centralized radiator system. As per the scope of work of this task, the applicability of refrigeration system tailored to meet the specialized requirements of storage of food and biological samples was investigated. The issues addressed were the anticipated power consumption and feasible designs and cycles for meeting specific storage requirements. Further, development issues were assessed related to the operation of vapor compression systems in micro-gravity addressing separation of vapor and liquid phases (via capillary systems).

Dean, W. G.↗

NASA NTRS2002

Microelectric Heterogeneous Hybrid Devices for Space Applications

The existing projects designated as SACA (Sample Ampoule Cartridge/Container Assembly) and QMI (Quench Module Insert) at NASA's MSFC (Marshall Space Flight Center) involve development of high-temperature coating materials. A number of material systems need to be evaluated for this purpose. The requirement of these coating materials included high emissivity (approaching unity), sufficient physical strength, appropriate thermal conductivity to dissipate heat, and above all high temperature (T is equal to or greater than 2000 C) withstanding capability. Potential materials for applications considered were non-oxide based materials such as tungsten carbide, tantalum carbide, compounds of niobium, etc.

Mohammad A. Alim↗

NASA NTRS2006

Effects of Vegetation and of Heat and Vapor Fluxes from Soil on Snowpack Evolution and Radiobrightness

The radiobrightness of a snowpack is strongly linked to the snow moisture content profile, to the point that the only operational inversion algorithms require dry snow. Forward dynamic models do not include the effects of freezing and thawing of the soil beneath the snowpack and the effect of vegetation within the snow or above the snow. To get a more realistic description of the evolution of the snowpack, we reported an addition to the Snow-Soil-Vegetation-Atmosphere- Transfer (SSVAT) model, wherein we coupled soil processes of the Land Surface Process (LSP) model with the snow model SNTHERM. In the near future we will be adding a radiobrightness prediction based on the modeled moisture, temperature and snow grain size profiles. The initial investigations with this SSVAT for a late winter and early spring snow pack indicate that soil processes warm the snowpack and the soil. Vapor diffusion needs to be considered whenever the ground is thawed. In the early spring, heat flow from the ground into a snow and a strong temperature gradient across the snow lead to thermal convection. The buried vegetation can be ignored for a late winter snow pack. The warmer surface snow temperature will affect radiobrightness since it is most sensitive to snow surface characteristics. Comparison to data shows that SSVAT provides a more realistic representation of the temperature and moisture profiles in the snowpack and its underlying soil than SNTHERM. The radiobrightness module will be optimized for the prediction of brightness when the snow is moist. The liquid water content of snow causes considerable absorption compared to dry snow, and so longer wavelengths are likely to be most revealing as to the state of a moist snowpack. For volumetric moisture contents below about 7% (the pendular regime), the water forms rings around the contact points between snow grains. Electrostatic modeling of these pendular rings shows that the absorption of these rings is significantly higher than a sphere of the same volume. The first implementation of the radiobrightness module will therefore be a simple radiative transfer model without scattering.

soil↗

NASA NTRS2009

Ascent Heating Thermal Analysis on the Spacecraft Adaptor (SA) Fairings and the Interface with the Crew Launch Vehicle (CLV)

When the crew exploration vehicle (CEV) is launched, the spacecraft adaptor (SA) fairings that cover the CEV service module (SM) are exposed to aero heating. Thermal analysis is performed to compute the fairing temperatures and to investigate whether the temperatures are within the material limits for nominal ascent aero heating case. Heating rates from Thermal Environment (TE) 3 aero heating analysis computed by engineers at Marshall Space Flight Center (MSFC) are used in the thermal analysis. Both MSC Patran 2007r1b/Pthermal and C&R Thermal Desktop 5.1/Sinda models are built to validate each other. The numerical results are also compared with those reported by Lockheed Martin (LM) and show a reasonably good agreement.

Wang, Xiao-Yen↗