SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This payload overview presentation will be presented at the Payload Operations Integration Working Group (POIWG) on April 26, 2018. It provides a high-level overview of Cell Science-02 operations.
Some of the obstacles to the commercialization of perovskite solar cells (PSCs) are their long-term moisture stability and material cost of the constituent layers, such as the commonly used spiro-OMeTAD hole transport layer (HTL). Replacing the spiro-OMeTAD with low-cost inorganic hole transport materials (HTMs) are important to further elevate the attractiveness of PSCs for commercialization. Perovskite-compatible, solution-exfoliated two-dimensional (2D) transition metal dichalcogenides (TMDCs) are being considered as viable candidates for inorganic HTMs. We consider one such TMDC, WSe 2 which was chemically exfoliated using dichlorobenzene (DCB), a perovskite-compatible solvent, as it was integrated with triple cation perovskite absorbers within the solar cell stack. Here, the WSe 2 HTL required heat treatment processes to be maintained below 100°C in order to preserve the integrity of the underlying perovskite; despite this lower temperature post treatment process, the structural morphology of the film revealed its dense and pinhole-free nature. Temperature-dependent transport studies conducted on the WSe 2 film provided evidence of its semiconducting character and its ability to extract holes well from the underlying triple-cation Cs 0.05 FA 0.79 MA 0.16 PbI 2.45 Br 0.55 absorber. The inorganic HTL offered better environmental stability in moisture-rich environments of up to 60% relative humidity, in comparison to spiro-OMeTAD HTL-based devices which degraded faster as a result of pinholes
We report additional results in our program to monitor the wavelength stability of lines in the 2.3 micrometer spectrum of integrated sunlight. We use the McMath Fourier transform spectrometer (FTS) of the National Solar Observatory to monitor 16 delta V = 2 lines of (12)C(16)O, as well as five atomic lines. Wavenumber calibration is achieved using a low-pressure N2O absorption cell and checked against terrestrial atmospheric lines. Imperfect optical integration of the solar disk remains the principal source of error, but this error has been reduced by improved FTS/telescope collimation and observing procedures. The present results include data from an additional 13 quarterly observing runs since 1985. We continue to find that the apparent velocity of integrated sunlight is variable, in the sense of having a greater reshift at solar maximum. This is supported by the temporal dependence of the integrated light velocity, and by the presence of a correlation between velocity and the disk-averaged magnetic flux derived from Kitt Peak magnetograms. The indicated peak-to-peak apparent velocity amplitude over a solar cycle is approximately the same as the velocity amplitude of the Sun's motion about the solar system barycenter. This represents about half the amplitude which we inferred in Paper I (Deming et al. 1987), but the present result has a much greater statistical significance. Our results have implications for those investigations which search for the Doppler signatures of planetary-mass companions to solar-type stars. We contrast our results to the recent finding by McMillan et al. 1993 that solar absorption lines in the violet spectral region are wavelength-stable over the solar cycle.
We report on a methodology for performing laser ray-tracing in three spatial dimensions for radiation-hydrodynamics simulation codes. Our method, which is an extension of that developed in Haines et al., Comput. Fluids 201, 104478 (2020), utilizes an automatically generated separate mesh for the laser ray-tracing from the radiation-hydrodynamics mesh. This enables the laser mesh to be tailored to minimize ray noise with significantly fewer rays than would be required when the ray-tracing is performed on the radiation-hydrodynamics mesh, primarily by allowing the use of high-aspect-ratio cells that are not suitable for hydrodynamics solvers. For a planar target, we show that our method provides a ≈ 100× reduction in computational expense to achieve a fixed level of ray noise relative to ray-tracing directly on the radiation-hydrodynamics mesh. The relatively low ray requirement also enables efficient computation of cross-beam energy transfer. Each cell in the logically cubic laser mesh is a non-convex dodecahedron with triangular sides, and numerical integration of the ray trajectories and inverse bremsstrahlung is performed by mapping each cell to the unit cube. We will describe our methodology in detail as well as its implementation in the xRAGE radiation-hydrodynamics code, discuss performance, and present the results from applying the methodology to test problems with analytic solutions for laser ray-tracing through a quadratic density gradient with an analytic solution as well as for a laser-driven heat front. In 3D radiation-hydrodynamics simulations of laser-driven experiments performed on the National Ignition Facility, laser ray-tracing with our methodology uses less than 1% of total computational time while introducing acceptably low levels of ray noise.
The objective of the proposed research was to begin the development of a non-invasive optical sensor for measuring glucose concentration in the output medium of cell cultures grown in a unique NASA bioreactor referred to as an integrated rotating-wall vessel (IRWV). The input, a bovine serum based nutrient media, has a known glucose concentration. The cells within the bioreactor digest a portion of the glucose. Thus, the non-invasive optical sensor is needed to monitor the decrease in glucose due to cellular consumption since the critical parameters for sustained cellular productivity are glucose and pH. Previous glucose sensing techniques have used chemical reactions to quantify the glucose concentration. Chemical reactions, however, cannot provide for continuous, real time, non-invasive measurement as is required in this application. Our effort while in the fellowship program was focused on the design, optical setup, and testing of one bench top prototype non-invasive optical sensor using a mid-infrared absorption spectroscopy technique. Glucose has a fundamental vibrational absorption peak in the mid-infrared wavelength range at 9.6 micron. Preliminary absorption data using a CO2 laser were collected at this wavelength for water based glucose solutions at different concentrations and one bovine serum based nutrient medium (GTSF) with added glucose. The results showed near linear absorption responses for the glucose-in-water data with resolutions as high at 108 mg/dl and as low as 10 mg/dl. The nutrient medium had a resolution of 291 mg/dl. The variability of the results was due mainly to thermal and polarization drifts of the laser while the decrease in sensitivity to glucose in the nutrient medium was expected due to the increase in the number of confounders present in the nutrient medium. A multispectral approach needs to be used to compensate for these confounders. The CO2 laser used for these studies was wavelength tunable (9.2 to 10.8 micrometers), however, it was to unstable across wavelengths to test the multispectral approach. From this research, further NASA support was obtained to continue the work throughout the year in which a more stable light source will be used at smaller, near-infrared, wavelengths. It is anticipated that a more compact, non-invasive, optical glucose sensor will be realized which can be used with a bioreactor on future space shuttle missions. It is also anticipated that a multispectral optical sensor may be used to determine the concentration of other molecules needed within the NASA bioreactor, such as fructose and galactose.
A nanostructural thin film is one of the highly exploiting research areas particularly in applications in sensor, photocatalytic, and solar-cell technologies. In the past two decades, the integration of glancing-angle deposition (GLAD) technique to physical vapor deposition (PVD) process has gained significant attention for well-controlled multidimensional nanomorphologies because of fast, simple, cost-effective, and mass-production capability. The performance and functional properties of the coated thin films generally depend upon their nanostructural compositions, i.e., large aspect ratio, controllable porosity, and shape. Such structural platforms make the fabricated thin films very practical for several realistic applications. We therefore present morphological and nanostructural properties of various deposited materials, which included metals, i.e., silver (Ag), and oxide compounds, i.e., tungsten oxide (WO{sub 3}), titanium dioxide (TiO{sub 2}), and indium tin oxide (ITO). Different PVD techniques based on DC magnetron sputtering and electron-beam evaporation, both with the integrated GLAD component, were discussed. We further explore engineered nanostructures which enable controls of optical, electrical, and mechanical properties. These improvements led to several practical applications in surface-enhanced Raman, smart windows, gas sensors, self-cleaning materials and transparent conductive oxides (TCO)
Silver plasma immersion ion implantation was used to decorate silver nanoparticles (Ag NPs) on tantalum oxide (TO) coatings. The coatings acted against bacterial cells (Staphylococcus epidermidis) in the dark by disrupting their integrity. The action was independent of silver release and likely driven by the electron storage capability of the Schottky barriers established at the interfaces between Ag NPs and the TO support. Moreover, no apparent side effect on the adhesion and differentiation of rat bone mesenchymal stem cells was detected when using Ag NPs-modified TO coatings. These results demonstrate that decoration of tantalum oxide using Ag NPs could be a promising procedure for improving the antibacterial properties for orthopedic and dental implants.
During the years, various techniques have been presented for optimal control of tumor growth for which its stochastic behavior has rarely been considered. This article uses the well-known Gompertz stochastic model, for describing tumor growth, and by receding horizon model predictive control (RH-MPC) scheme computes the drug dosage for minimizing the tumor-cell population. To do this, a predictive control problem is defined based on the difference between the probability density function of tumor-cell population and the desired probability density function. In the model, both the drug dosage limitation and the Fokker–Planck equation have been considered as constraints. By solving this problem, the drug dosage which is considered as an external input to tumor model, is computed. In this article, the Fokker–Planck equation is used (1) as a nonlinear observer of probability density function of tumor-cell population and (2) a mapping vehicle from stochastic to deterministic domain. The Fokker–Planck equation is written for the Gompertz stochastic model of tumor growth. The equation is then solved through the path integral method. In this way, the probability density function of tumor-cell population, which contains the entire stochastic characteristics of the tumor growth, is obtained for any instance of time. The simulation results have also been presented for the evaluation of the suggested approach. The results show that the tumor-cell population can be controlled within a number of time windows (15 time windows in our case study) if an appropriate desired PDF is selected.
Stacking solar cells with decreasing band gaps to form tandems presents the possibility of overcoming the single-junction Shockley-Queisser limit in photovoltaics. The rapid development of solution-processed perovskites has brought perovskite single-junction efficiencies >20%. However, this process has yet to enable monolithic integration with industry-relevant textured crystalline silicon solar cells. We report tandems that combine solution-processed micrometer-thick perovskite top cells with fully textured silicon heterojunction bottom cells. To overcome the charge-collection challenges in micrometer-thick perovskites, we enhanced threefold the depletion width at the bases of silicon pyramids. Moreover, by anchoring a self-limiting passivant (1-butanethiol) on the perovskite surfaces, we enhanced the diffusion length and further suppressed phase segregation. These combined enhancements enabled an independently certified power conversion efficiency of 25.7% for perovskite-silicon tandem solar cells. These devices exhibited negligible performance loss after a 400-hour thermal stability test at 85°C and also after 400 hours under maximum power point tracking at 40°C.
The Radar Wind Sensor (RAWS) was proposed as a complement to laser wind sensors, allowing coverage in cloudy regions excluded from laser coverage. Previous University of Kansas studies showed the feasibility of the wind measurement at various levels in the atmosphere and indicated that RAWS can also measure rain rates and ocean-surface winds. Here we discuss measurement of the wind vector in terms of the scan patterns for a conically scanned antenna. By using many measurements from cells about 66 km square and 132 km square, a least-squares algorithm gives results that are reasonable for insertion into global atmospheric models. For RAWS to be used successfully as a complement to a laser wind sensor, the design of the two sensors should be integrated and radial velocity measurements in a given atmospheric cell should be combined to get the most accurate results.
Optimizing the metabolism of microbial cell factories for yields and titers is a critical step for economically viable production of bioproducts and biofuels. In this process, tuning the expression of individual enzymes to obtain the desired pathway flux is a challenging step, in which data from separate multiomics techniques must be integrated with existing biological knowledge to determine where changes should be made. Following a design-build-test-learn strategy, building on recent advances in Bayesian metabolic control analysis, we identify in this work key enzymes in the oleaginous yeast Yarrowia lipolytica that correlate with the production of itaconate by integrating a metabolic model with multiomics measurements. To this extent, we quantify the uncertainty for a variety of key parameters, known as flux control coefficients (FCCs), needed to improve the bioproduction of target metabolites and statistically obtain key correlations between the measured enzymes and boundary flux. Based on the top five significant FCCs and five correlated enzymes, our results show phosphoglycerate mutase, acetyl-CoA synthetase (ACSm), carbonic anhydrase (HCO3E), pyrophosphatase (PPAm), and homoserine dehydrogenase (HSDxi) enzymes in rate-limiting reactions that can lead to increased itaconic acid production.
The National Aeronautics and Space Administration Convergent Aeronautics Solutions project seeks to determine feasibility of emerging technologies in aeronautics. The Aqueous, QUick-Charging Battery Integration For Electric flight Research study pursued the feasibility of nano-electro fuel and rim-driven motor technologies integrated together for aircraft implementation. Development of the NEF technology was in partnership with Influit Energy, LLC (Chicago, Illinois). A rim-driven motor, designed by the project team, sized to represent one of 24 motors in the propulsion system of the tandem electric super-short takeoff and landing aircraft is discussed. The development of this electric super-short takeoff and landing concept was in partnership with The Boeing Company (Chicago, Illinois). The integrated system design of the nano-electro fuel and rim-driven motor technologies within the wing section was in partnership with Empirical Systems Aerospace, Inc. (ESAero) (San Luis Obispo, California). The feasibility benchmark for the nano-electro fuel battery was to attain 100 mA/sq. cm within two years, a 50-fold increase over the demonstrated cell performance before the Convergent Aeronautics Solutions Aqueous, QUick-Charging Battery Integration For Electric flight Research activity. The team achieved 85 mA/sq. cm in the nano-electro fuel flow cell at the end of the two years. The Aqueous, QUick-Charging Battery Integration For Electric flight Research project team determined the technology to be both inflammable and nonexplosive (unless multiple, simultaneous system failures occur) which would provide a safer alternative to conventional lithium-ion based battery systems.
Human epidermal growth factor receptors (HER, also known as ErbB) drive cellular proliferation, pro-survival and stress responses by activating several downstream kinases, in particular ERK, p38, JNK (SAPK), the PI3K/AKT, as well as various transcriptional regulators such as STAT3. When co-expressed, first three members of HER family (HER1-3) can form homo- and hetero-dimers. Based on the considerable evidence which suggest that every receptor dimer activates intracellular signaling pathways differentially, we hypothesized that the HER dimerization pattern is a better predictor of downstream signaling than the total receptor activation levels. We validated our hypothesis using a combination of model-based analysis to quantify the HER dimerization patterns and multi-factorial experiments where HER dimerization patterns and signaling crosstalk were rationally perturbed. We have measured the activation of HER1-3 receptors and of the sentinel signaling proteins ERK, AKT, p38, JNK, STAT3 as a function of time in a panel of human mammary epithelial (HME) cells expressing different levels of HER1-3 stimulated with various ligand combinations. Our analysis using multiple ways of clustering the activation data has confirmed that the HER receptor dimer is a better predictor of the signaling through p38, ERK and AKT pathways than the total HER receptor expression and activation levels. Targeted inhibition studies to identify the causal effects allowed us to obtain a consensus regulatory interaction model, which revealed that STAT3 occupies a central role in the crosstalk between the studied pathways.
A series of conjugated T2 polymers (PBBF1-T2 and PBBCl1-T2), and T3 polymers (PBBF1-T3, PBBCl1-T3 and PBBCl2-T3) were synthesized using chlorinated/fluorinated benzothiadiazole (BT) and the two-dimensional benzo[1,2-b:4,5-b']dithiophene (BDT) units as the building blocks. When compared to the fluorinated polymer, the performance of the polymer photovoltaic devices showed that these chlorinated polymers gave extended optical absorption spectrum, and lower highest occupied molecular orbital (HOMO) energy levels. The introduction of chlorine atoms increases the twist angle between the polymer backbones, and led to a lower HOMO energy level and resulted in the increase of open circuit voltage (V oc) up to 0.84 V in PBBCl2-T3 based devices with a two chlorine substitution. However, the device based on PBBCl1-T3 with only one chlorine atom exhibited the best power conversion efficiency (PCE) which was as high as 6.87% with a V oc of 0.73 V, and this was about 10% higher than that of its fluorinated analogs. Here, this result indicated that the introduction of chlorine atoms into polymers is not only a simple route to synthesize a large amount of material and which avoids the tedious synthesis steps in widely used fluorinated polymers, but it is also a feasible and effective strategy to fine tune the energy level of polymer solar cell with optimized PCE. Furthermore, it is worth noting that the introduction of longer π-conjugation side chains could minimize the influence of chlorine substitution by reducing the twist angle between the polymer backbones, which would reduce the gap of V oc between the chlorinated polymers and their fluorinated analogs.
The rational molecular design and structural modification of quasi-two-dimensional fused perylene diimide (quasi-2D FPDI) acceptors have received growing attention for application in non-fullerene organic solar cells (NF-OSCs). Herein, we designed and synthesized two pairs of FPDI acceptors, one in the form of FPDI–π-bridge–FPDI with the π-bridge being either an axisymmetric thiophene (T) or a centrosymmetric thienothiophene (TT) unit, and the other being the corresponding ring-fusion counterpart. Additionally, four small molecule acceptors, namely T-FPDI, TT-FPDI, FT-FPDI and FTT-FPDI, were paired with a common PTB7-Th polymeric electron donor as active materials for a comparative study of the effects of linkers and ring fusion on their photovoltaic performances. The T-FPDI-based NF-OSC exhibited a decent power conversion efficiency (PCE) of 5.50%, while a higher PCE of 7.17% with a simultaneous enhancement in the open circuit voltage ( V oc ), the short-circuit current density ( J sc ) and the fill factor (FF) was achieved for the TT-FPDI-based solar cells. The solar cells based on the ring-fused FT-FPDI and FTT-FPDI acceptors displayed PCEs of 6.75% and 7.66%, respectively, both higher than those of the corresponding non-fused counterparts. Notably, the trade-off between the J sc and V oc , commonly observed in fullerene OSCs, is alleviated in these systems. It is also worth noting that the NF-OSCs based on these FPDI acceptors do not need any solvent additives. Overall, this successful molecular engineering based on novel quasi-2D FPDI building blocks may inspire the development of emergent electron acceptors for high performance additive-free NF-OSCs.
High-energy-density primary (nonrechargeable) electrochemical cells capable of relatively high discharge currents at temperatures as low as -40 C have been developed through modification of the chemistry of commercial Li/CFx cells and batteries. The commercial Li/CFx units are not suitable for high-current and low-temperature applications because they are current limited and their maximum discharge rates decrease with decreasing temperature. The term "Li/CFx" refers to an anode made of lithium and a cathode made of a fluorinated carbonaceous material (typically graphite). In commercial cells, x typically ranges from 1.05 to 1.1. This cell composition makes it possible to attain specific energies up to 800 Wh/kg, but in order to prevent cell polarization and the consequent large loss of cell capacity, it is typically necessary to keep discharge currents below C/50 (where C is numerically equal to the current that, flowing during a charge or discharge time of one hour, would integrate to the nominal charge or discharge capacity of a cell). This limitation has been attributed to the low electronic conductivity of CFx for x approx. 1. To some extent, the limitation might be overcome by making cathodes thinner, and some battery manufacturers have obtained promising results using thin cathode structures in spiral configurations. The present approach includes not only making cathodes relatively thin [.2 mils (.0.051 mm)] but also using sub-fluorinated CFx cathode materials (x < 1) in conjunction with electrolytes formulated for use at low temperatures. The reason for choosing sub-fluorinated CFx cathode materials is that their electronic conductivities are high, relative to those for which x > 1. It was known from recent prior research that cells containing sub-fluorinated CFx cathodes (x between 0.33 and 0.66) are capable of retaining substantial portions of their nominal low-current specific energies when discharged at rates as high as 5C at room temperature. However, until experimental cells were fabricated following the present approach and tested, it was not known whether or to what extent low-temperature performance would be improved.
We demonstrate continuous roll-to-roll (R2R) fabrication of single junction and tandem organic photovoltaic (OPV) cells on flexible plastic substrates employing a system that integrates organic deposition by high vacuum thermal evaporation (VTE) and low pressure organic vapor phase deposition (OVPD). By moving the substrate from chamber to chamber and then depositing films on stationary substrates, we achieve power conversion efficiencies of PCE = 8.6 ± 0.3% and 8.9 ± 0.2% for the single junction and tandem cells, respectively. Single junction OPVs are also fabricated on a continuously translating substrate at 0.3 cm/s, to achieve PCE = 8.5 ± 0.2%. Thin films grown on translating substrates by OVPD show <3% thickness non-uniformity and 0.66 nm root mean square surface roughness, similar to that obtained by VTE. Our results suggest that R2R film deposition comprising multiple vapor deposition technologies is a promising method for rapid speed and continuous manufacturing of high quality, small molecular weight organic electronic materials.
Growth of III-V materials on Si could enable dramatic cost reduction for III-V PV by eliminating the need for expensive III-V substrates and enabling high-efficiency tandem solar cells. The direct heteroepitaxy of III-V materials on Si for high-efficiency photovoltaics has progressed greatly in recent years, but most studies have focused on off-cut wafers polished using an expensive chemical-mechanical planarization process (which is not used for commercial solar cells). Alternative growth approaches are needed that can enable the integration of high material quality III-Vs with PV-grade Si materials. Here we demonstrate the use of cost-effective patterning and etching approaches to create templates for selective area epitaxy on PV-grade Si substrates. We investigate the nucleation of III-V materials on these substrates.