A Corrosion Test Station for Improved Characterization and Examination Capabilities of Advanced Nuclear Reactor Fuels and Materials
Explore the source record for details and available documents.
Grimm, Terry↗
SEARCH · Engineering Papers
Results for “Test Reactor”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Irradiation Testing of Nuclear Flux Sensors - Presentation for 2021 ASI Annual Webinar
This power point presentation is a summary of the work produced in FY2021 under the Irradiation Testing of Neutron Flux Sensors project funded by DOE's Advanced Sensor Initiative, and the outlook for FY22. The objective of this portion of the ASI program is to "Test and demonstrate in-pile instrumentation in conditions similar to those expected to be seen in service, i.e., the conditions they would see in either in irradiation experiments supporting advanced reactors, or ultimately, in advanced reactors themselves". The presentation describes how neutron flux sensors were tested in four INL reactors plus Idaho State University's research reactor during FY2021, and the results obtained from these tests.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Convolutional Neural Network–Aided Temperature Field Reconstruction: An Innovative Method for Advanced Reactor Monitoring
In this study, the capabilities of a physics-informed convolutional neural network (CNN) for reconstructing the temperature field from a limited set of measurements taken at the boundaries of internal flows are demonstrated. Such an approach enables the development of less invasive monitoring methods for real-time plant diagnostics. As a test case, a Molten Salt Fast Reactor (MSFR) design was selected. This circulating fuel reactor has received interest from both scientific and industrial communities due to its intrinsic safety and sustainability. Molten salt flows in such reactors, however, can present highly localized temperature peaks that can induce significant thermal stresses onto the vessel walls. At these local maxima, the salt temperature may exceed a thousand kelvins, which makes a direct measurement challenging or even unfeasible. The proposed CNN algorithm allows one to detect indirectly such discontinuities through an accurate, albeit indirect, temperature measurement method during reactor operation. The datasets employed to train and test the machine learning models in the present work were generated with Nek5000, a computational fluid dynamics (CFD) code developed at Argonne National Laboratory. The CNN algorithm is trained with CFD results that span a set of MSFR operational power and flow ranges. Here, to demonstrate the efficacy of the algorithm, predictions are made for test cases contained within the training range but for which the CFD data were not used when training. Results demonstrate that the proposed technique properly characterizes temperature peaks and distributions within the domain for a broad range of scenarios.
21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
Using FIPD and OPTD to Benchmark Metallic Fuel Performance
This report serves as an introduction, tutorial, and benchmark specification for out-of-pile tests on metallic fuel. It introduces a new user to the EBR-II legacy fuel performance test program and the fast reactor fuel performance databases built to preserve the records. It then details the information stored in each database and how to find it. A benchmark specification is included for a small set of out-of-pile tests on U-10Zr fuel to function as a tutorial demonstrating how the legacy fuel performance data sets stored in the FIPD and OPTD databases can be used together to benchmark fuel performance models for steady-state and transient performance.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Determining the effects of U/Pu ratio on subsolidus phase transitions in U-Pu-Zr metallic fuel alloys
Here, ternary alloys consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are among the leading candidate fuel systems considered for fast spectrum nuclear reactors. Despite historical operation data from the testing of U-Pu-Zr rods in the Experimental Breeder Reactor-II, considerable uncertainty about the evolution of phases and microstructure across the ternary composition space exists. Due to sluggish kinetics and other difficulties in handling metal actinide specimens, quantitative measurements of phase-transitions in U-Pu-Zr alloys remain sparse in scientific literature, with most investigators reporting either phase-transition temperatures or phase identification data, but not both from the same specimens. The purpose of this paper is to critically compare experimental and calculated phase transition data and correlate with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Phase transition peaks were measured using differential scanning calorimetry in the subsolidus regions (723-948 K) of three ternary U-Pu-Zr alloys with the same zirconium concentration but various U/Pu ratios. Overlapping peaks were deconvoluted using a Frazier-Suzuki peak fitting algorithm, and the critical peak temperatures and enthalpies were calculated. In general, increasing concentrations of Pu were associated with enhanced thermal stability of the body-centered cubic γ phase upon both heating and cooling. Experimental phase transition temperatures in this study tended to agree well with the predictions of the established ternary phase diagrams and other reported phase transition temperatures in literature. Additionally, the TAF-ID thermodynamic database was used to calculate a U-Pu-40 at.% Zr pseudobinary diagram as well as ternary diagrams from 773 to 973 K. The equilibrium phase transition temperatures tended to be considerably lower than measured peak temperatures upon both heating and cooling. Recommendations for improving the quality of data in future U-Pu-Zr characterization studies are also discussed.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
ORNL Testing of Multiple Graphite Benchmarks [Slides]
Integral criticality safety and reactor physics benchmark experiments from the International Handbook of Evaluated Criticality Safety Benchmark Experiments (ICSBEP Handbook) and the International Handbook of Reactor Physics Experiments (IRPhE Handbook) are essential for nuclear data validation and testing
ENDF↗
In-Sodium Testing of a Prototype Thermoacoustic Power Sensor for Sodium-Cooled Fast Reactors
The ultimate goal of this project is to develop and demonstrate a thermoacoustic power sensor (TAPS) for Sodium-Cooled Fast Reactors (SFRs), with potential application also envisioned to other nuclear technologies such as Lead-Cooled Fast Reactors (LFRs), Molten Salt Reactors (MSRs), in addition to Light Water Reactors (LWRs). The project was led by Westinghouse Electric Company, LLC (Westinghouse) and carried out in collaboration with Argonne National Laboratory (ANL) and the University of Pittsburgh. A TAPS is a passive (self-powered), non-invasive (wireless) sensor envisioned for measuring key parameters, such as local temperature and neutron flux, in a nuclear reactor core. The sensor generates pressure waves (i.e., sound waves) with a frequency and amplitude dependent upon nuclear operating conditions (coolant temperature or power changes). The acoustic waves are able to travel through the core and associated structures, and reach to the sensor network placed outside and/or inside of the reactor vessel. These sensors require a very small amount of power which, during loss of power events, can be provided, for example, by harvesting gamma radiation energy, thus resulting in a monitoring system that can function both during normal operation and during loss of power events. Westinghouse and the University of Pittsburgh designed and fabricated TAPS prototypes for Argonne National Laboratory (ANL) to carry out in-sodium testing to evaluate the effects of sodium on the TAPS and the performance of the TAPS technique in sodium. Argonne received a TAPS prototype from Westinghouse, and the prototype was modified such that it can be installed into a test vessel and function in sodium at elevated temperature without potentially leaking. A water mockup test apparatus was constructed to validate proper working of the prototype. An instrumentation and control (I&C) system, running on the National Instruments (NI) LabView platform, was developed to: 1) operate both the water mockup test and the in-sodium test facility; and 2) process and analyze the received acoustic signals from an array of accelerometers and the Argonne sodium-submersible high-temperature acoustic sensor. The prototype was successfully tested in a water bath at different temperatures. Water mockup tests demonstrated that the TAPS prototype is working properly and its resonance frequency changes linearly with the coolant (water) temperature. A TAPS test apparatus was constructed and integrated with the upgraded Under-Sodium Viewing (USV) sodium test facility. The integrated USV-TAPS sodium test facility has been operational. The TAPS prototype and a high-temperature sodium-submersible acoustic sensor (SSAS) developed by Argonne were both installed inside the TAPS test vessel. Being operated within argon cover gas under ambient conditions, the TAPS prototype demonstrated that it was functioning properly with a resonance frequency at 1407.2 Hz, which was successfully detected by the accelerometers mounted on the external wall of the vessel and the high-temperature SSAS installed inside the vessel. After successfully transferring sodium into the vessel, in-sodium tests of the prototype were conducted. Tests of the TAPS prototype demonstrated that the resonance frequency of the TAPS changes linearly with respect to the temperature difference between the interior of the TAPS and bulk sodium. The early tests showed that the TAPS prototype could not establish a continuous and consistent resonance in sodium. The resonance diminished before the prototype reached its operating temperature. A signal postprocessor was added to the DAQ module latterly to isolate interferences, enhance signal conditioning, improve peak detection, and generate resonance frequency versus temperature plots. After testing in molten sodium and immersion at higher temperature for several weeks, the TAPS prototype was able to establish a continuous resonance. Performance evaluation of the TAPS prototype was then conducted in sodium. The tests included the investigation of 1) the effects of the temperature difference between the TAPS and bulk sodium, 2) the effects of sodium flowrate; and 3) the performance of the different sensor-receiver systems positioned inside or outside the vessel. Results of a test demonstrated that, with limited sodium circulation, a continuous and consistent resonance of the TAPS prototype was established occasionally. The tests also demonstrated that, because of the nature of detection principles and mounting methods, the high temperature SSAS is more affected by acoustic noise, while accelerometers are more affected by vibrations, in the test environment. It is unknown why the TAPS prototype only occasionally established a continuous and consistent resonance when the TAPS temperature reached its operating temperature in molten sodium, and why it ultimately failed to resonate at all. A failure modes assessment was conducted and a few potential causes of failure were identified. Different post in-sodium tests were conducted to obtain additional information potentially relevant to the cause of the failure. Nondestructive evaluation techniques are suggested to examine the internal integrity as well as the gas mixture of the prototype. If they prove inconclusive, the prototype should be cut open to conduct a thorough inspection of its internal integrity and determine the state of the gas mixture.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Complete Survey of Fuel Candidates for Microreactor Purposes
This report summarizes various fuel types that may be applicable to several microreactor concepts, which are defined as (1) very high temperature reactors (VHTR), (2) sodium fast reactors (SFR), (3) system for nuclear auxiliary power (SNAP) reactors, (4) gas fast reactors (GFR), and (5) molten salt reactors (MSR). The fuel systems that were assessed include: uranium mononitride (UN), uranium monocarbide (UC), uranium dioxide (UO 2 ), uranium oxycarbide (UCO) Tristructural Isotropic (TRISO), UN TRISO, mixed oxide (MOX), metallic fuels, and metal hydrides. While UCO TRISO has undergone significant testing through the advanced gas reactor (AGR) program, the very high cost necessitates consideration of other fuel types. UN and UC were identified as fuels that should receive further investigation due to their thermophysical and mechanical properties. Minimal irradiation performance data shows that these fuels are good candidate fuels for microreactors.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
RuKY Catalyst‐Packed Permeation Membrane for Quantitative Ammonia and d3‐Ammonia Dehydrogenation to Ultrapure Hydrogen
Ammonia is a promising carbon-free hydrogen carrier, but incomplete ammonia dehydrogenation (cracking) generates atmospheric emissions of NO x , a potent greenhouse gas. Additionally, incomplete cracking of ammonia leads to regulatory challenges in nuclear and fusion power, where tritiated ammonia (NT 3 ) emissions are strictly controlled. Therefore, we report the use of low-temperature ammonia dehydrogenation catalysts (3%Ru/1%Y/12%K/Al 2 O 3 ) in a palladium alloy H 2 permeation membrane for quantitative conversion of ammonia into hydrogen and nitrogen at industry-relevant conditions. This catalytic membrane reactor system achieved an astonishing effluent concentration of <1 ppm at 450°C under a 100% NH 3 stream, which is far beyond the 99.6% conversion target required for the adoption of ammonia as a vehicle fuel. The low-temperature ammonia dehydrogenation catalyst was tested in a packed bed reactor with NH 3 and ND 3 to both elucidate the reaction mechanism and to quantify the kinetic isotope effect of the membrane reactor. The rate-limiting step at temperatures relevant to the palladium membrane are isotope independent, indicating that the isotopologue content will not modify the desired reaction kinetics. By reducing emissions to below-trace levels with no additional separation, this work provides a path to greatly simplified and miniaturized ammonia cracking processes.
ammonia decomposition↗
Irradiation Behavior of Piezoelectric Materials for Nuclear Reactor Sensors
In-situ measurement of surface acoustic wave (SAW) resonators were used to characterize piezoelectric materials behavior in a nuclear reactor environment. Lithium niobate and aluminum nitride devices were tested up to 500°C temperature and 450 kW reactor power (1.9x10 12 n/cm 2 s). The resonant frequency responds to step changes in temperature and power. Materials’ response are inferred from the observed resonant frequency changes, in particular the kinetic behavior is used to determine mechanisms responsible for observed changes. The observed response is attributed to two mechanisms: temperature increase from gamma heating and accumulation of radiation-induced defects. Both of these mechanisms alter the physical properties of the piezoelectric materials, particularly the elastic constants. The demonstrated repeatability and reliability of SAW devices are attractive for sensor applications in extreme environments.
36 MATERIALS SCIENCE↗
Optimization Simulations for a Gamma-Ray Calibration Standard for a Cyclic Neutron Activation Analysis Pneumatic System at the Penn State Breazeale Reactor
For new experimental setups, the initial testing and calibrations can be expensive and time consuming without prior optimization. However, these issues can be mitigated using realistic modeling and simulation studies of the proposed system a priori. Specifically, an experiment can be performed virtually using realistic simulations and the expected results evaluated to inform adjustments of the experimental setup to achieve optimum results. At the Penn State Breazeale Reactor, a new pneumatic transfer system has been developed for the detection and characterization of short-lived fission fragments to enhance and complement existing nuclear data. The system accomplishes this task by transporting samples cyclically between an assortment of gamma-ray/neutron detectors and the reactor-core vicinity with sub-second transit times. The measured neutron flux paired with simulations of detector response using Geant4 and a custom module for estimating cascade summing effects and corrections were used to select sample-material masses for system characterization. With the optimized sample masses, an experimental counting plan for characterizing the repeatability of the newly developed pneumatic system was developed. Finally, the predictions made with these simulations allowed for optimization of the irradiation sample characteristics and gamma-ray detection system.
cyclic neutron activation, gamma-ray spectroscopy↗
MARVEL Utilization Plan
This report provides a high-level overview of the utilization plan for the MARVEL microreactor. The main focus is on discussing testing and application-demonstration opportunities that leverage the reactor. With the reactor rapidly progressing towards demonstration, along with the short (2- year) operational window, it was deemed critical to establish a basis for how stakeholders can engage with the program and leverage the reactor as a testbed. This report discusses potential opportunities to use MARVEL, leveraging from data and design access to testing novel controls, and novel nuclear-electric and nuclear-heat applications. It provides guidance for interested stakeholders on potential funding opportunities that can be pursued to support tests during the operational lifetime of the reactor. The report discusses the recommended strategy for outreach and the organizational structure to review and select projects for participation. Interested stakeholders are encouraged to fill out a questionnaire on how they could leverage MAVEL at this link: https://qfreeaccountssjc1.az1.qualtrics.com/jfe/form/SV_72InKjSEz54Q2j4 It is important to emphasize that this is intended to be a living document (updated annually or as needed) with revisions issued as the MARVEL demonstration timeline evolves. Similarly, the framework for engagement is subject to change as the project progresses.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Proposed New STELLA-2 Tests
In 2025, KAERI and Argonne initiated a collaboration based on software validation using data from tests performed at KAERI’s STELLA-2 facility. STELLA-2 is a large-scale sodium thermal-hydraulic test facility that was originally developed to support KAERI’s development of the PGSFR design concept. KAERI has performed a large number of tests at STELLA-2, providing valuable data to support sodium fast reactor code validation. KAERI will be conducting new tests in 2026, targeting system conditions that were not achieved during previous test campaigns. KAERI has requested from Argonne proposed tests that could be performed during the upcoming test campaign. This report documents Argonne’s proposed tests in fulfillment of KAERI’s request.
21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
Dispersal of high-burnup fuel fragment surrogate particles during and after loss-of-coolant accident tests
The issue of fuel fragmentation, relocation, and dispersal is critical in the licensing and use of high-burnup (>62 GWd/MTU) nuclear fuel in light water reactors (LWRs). In this work, two test series are reported that examine the fragment dispersal during a burst event and an additional dispersal following the burst due to vibrations in the rod, such as those induced by accident recovery systems. To examine dispersal during the balloon and burst portion of a Loss-of-Coolant Accident event, HfO 2 fragments and yttria-stabilized zirconia pellets were filled into an as-fabricated cladding tube, which was then pressurized and subjected to loss-of-coolant accident testing in steam. Results from this test were found to be highly non-prototypic, and dispersal was both significantly more violent and significantly greater in magnitude than identified for actual fuel tests. These findings were attributed to the conservative (more dispersive) nature of the particles chosen for dispersal and to the details of the test conditions used that led to particularly wide bursts. Further, the second set of tests examined dispersal following the burst when vibrations were induced in the rod, primarily via recovery activities such as Emergency Core Cooling System actuation leading to rapid water addition. Post-burst dispersal testing was performed by inducing sinusoidal oscillations with 2–25 nm peak-to-peak amplitude and 2–5 Hz frequencies in pre-burst rods that had been refilled with HfO 2 fragments or high-burnup fragment surrogate mixture of HfO 2 fragments and yttria-stabilized zirconia sands. Testing revealed that rods with large burst openings (7 mm wide in this work) led to unmitigated dispersal from above the burst zone but that smaller bursts (5 mm wide), although still much larger than the mean fragment size of 3 mm, led to effectively no dispersal because of interparticle locking. Additionally, mixture and moisture were found to impact the amount of dispersal: mixtures increased dispersal, and moisture drastically reduced it. The implications of these findings on likely dispersal from actual fuel are discussed.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Design Status and Experimental Strategy for Initial Molten Salt Irradiation Experiments in HFIR
The development and deployment of molten salt reactor (MSR) technologies require experimental capabilities that can evaluate molten fuel salt behavior and structural material performance under representative irradiation conditions. Although modeling and separate effects testing provide important insight, there remains a critical lack of in-pile data that capture the coupled effects of neutron irradiation, temperature, salt chemistry, and time. Informed by lessons learned from historical MSR programs and recent international irradiation efforts, this report presents a structured approach to addressing existing gaps in molten salt irradiation testing using the High Flux Isotope Reactor (HFIR). A phased irradiation strategy is presented that incrementally increases experimental complexity while managing cost, risk, and facility constraints. The framework progresses from passive, nonfueled static capsule experiments to fueled, instrumented, and ultimately circulating molten salt systems, providing a pathway for materials screening, mechanistic understanding, and qualification-relevant testing. The report defines a near-term Phase 1 passive capsule concept, associated irradiation conditions, and a conceptual post-irradiation examination strategy. Ongoing modeling, out-of-pile testing, and safety analysis activities are described to support continued capability maturation and to enable future phases of molten salt irradiation testing in support of MSR technology deployment.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Enabling a Physical Twin for Control Methods Evaluation
Advanced nuclear reactors play an important role in the energy future of the United States and the rest of the world. They are designed and operated based on a different model than that of the current operating fleet, thus enabling deployment in remote locations and allowing for safe semi-autonomous or autonomous operations. Such characteristics require the development of a new reactor control paradigm. A significant factor in the development of control technologies and methods is integration of the various technologies and methods with each other and with hardware (both reactor system hardware and control hardware). A recent workshop on control of advanced reactors identified the lack of a flexible, expandable software/hardware infrastructure to enable such integration as a key gap. A previous phase of the current effort involved developing and demonstrating the Control and Optimization Modular Modeling Application for Nuclear Deployment (COMMAND) platform, which is capable of integrating autonomous-control-enabling technologies and methods, without the constraints imposed by existing software solutions. This platform will enable advanced reactor developers to deploy and test any developed technologies and methods by employing a common framework, and to couple them with their own models and hardware. The present phase of this effort entails using the Microreactor Automated Control System (MACS) platform, which was developed by the U.S. Department of Energy (DOE) Microreactor Program, to serve as a control method testbed. MACS can be used by advanced reactor developers to integrate their control related research activities with any reactor system. For the present effort, MACS was customized to mirror Idaho National Laboratory (INL)’s Microreactor Applications Research Validation and Evaluation (MARVEL) microreactor, and COMMAND was leveraged to enable MACS to emulate the physics of MARVEL, thus positioning MACS as a physical twin of MARVEL.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Ceramic Composite Experimental Testing Status
Over recent years, ceramic matrix materials such as SiC–SiC and C–C have been gaining interest for use in fusion reactors, light water reactors (LWRs), and high-temperature reactors (HTRs). These materials are good candidates to operate in very high temperature and moderate to high radiation environments. The evaluation of composite materials, in general, is challenging because of variations in precursor materials, variations in the fabrication process across fabricators, and the wide range of potential fiber architectures, to name a few. However, the need to evaluate neutron-irradiated properties adds another layer of complexity, which includes cost, timeline, and specimen size limitations (often associated with irradiation testing). A qualification methodology for the use of ceramic composites is provided in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section III-5-HHB. The methodology is supported by ASTM International (ASTM) guides, which provide a pathway to accomplish this effort. Part of the qualification strategy is for the designer to collect material property data on environmental conditions representative of its design envelope. These data include irradiation effects. This report presents an experimental study and test campaign developed to partially address this gap by providing initial mechanical and physical property data required for design. A variety of different materials using different manufacturing techniques are considered as part of this campaign. The test plan suggests performing a screening or partial irradiation study to assist the designer during the material selection process. The designer can then perform a more comprehensive qualification study if the material performance is promising. This work focuses on the status of the specimen preparations (machining of samples), the current test methods and failure analysis as well as the preparation of irradiation vehicles for the irradiation campaign. The irradiation will be performed at Oak Ridge National Laboratory (ORNL) in the High Flux Isotope Reactor (HFIR) and at Idaho National Laboratory (INL) in the Advanced Test Reactor (ATR).
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Development of an Improved RELAP5-3D Model for the High Temperature Test Facility
High-temperature gas-cooled reactors (HTGRs) are rapidly approaching deployment. Confidence in transient analysis of these systems requires modeling and simulation tools that have been validated against data relevant to HTGR conditions. The High Temperature Test Facility (HTTF) is an integral effects thermal hydraulics test facility for prismatic HTGRs. In spring and summer of 2019, HTTF was used for a series of experiments that now serve as the basis for the Organization of Economic Cooperation and Development / Nuclear Energy Agency Thermal Hydraulic Code Validation Benchmark for High Temperature Gas-Cooled Reactors using HTTF Data (HTGR T/H Benchmark). Previous analyses as part of the HTGR T/H benchmark used a RELAP5-3D model developed at Idaho National Laboratory (INL) and demonstrated an ability to reproduce trends in the measured data but difficulties reproducing experimental values within their uncertainty. These difficulties were largely attributed to assumptions made during the development of the initial RELAP5-3D model, which predated the HTTF experiments. A significant cause of difficulty reproducing the measured temperatures may be the radial nodalization of the previous RELAP5-3D model. In this paper, we present a new RELAP5-3D model of HTTF with finer radial nodalization built to assess the impact of radial heat transfer. We describe the new model and compare it against the old one at full-power steady state and for the pressurized conduction cooldown (PCC) transient. These analyses are based on the code-to-code comparison exercise for the PCC problem of the HTGR T/H benchmark. We compare maximum block temperature as the primary figure of merit and include discussion on intracore natural circulation.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗