Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRAILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

A transonic study of active flutter suppression based on an aerodymamic energy concept

The application of active control technology to the suppression of flutter has been successfully demonstrated in the Langley transonic dynamics tunnel. This study involved the implementation of an aerodynamic-energy criterion to suppress flutter of a simplified delta-wing model. Use of this technique with both leading- and trailing-edge active controls has resulted in an increase in dynamic pressure of 22% above the basic wing flutter point and with only a trailing-edge active control has resulted in an increase in dynamic pressure of 30% above the basic wing flutter point at a Mach number of 0.9. Analytical methods used to predict the open- and closed-loop behavior of the model are also discussed.

Sandford, M. C.↗

Deviation angle estimation for axial-flow compressors using inviscid flow solutions

Development of a more satisfactory method of estimating deviation angles was attempted using analytical procedures. Solutions for inviscid, irrotational flow in the blade-to-blade plane were obtained with a finite-difference calculation method. Deviation angles for three cascades with rounded trailing edges were estimated using the inviscid flow solutions and four existing trailing edge hypotheses. The estimated deviation angles were compared with experimental values for a range of incidence angle and inlet flow angle. None of the hypotheses were satisfactory at all incidence angles for all the cascades considered. An alternative hypothesis is presented which is suitable for one of the cascade profiles over a range of incidence and blade setting angle.

Miller, M. J.↗

Multiple contrail streamers observed by radar

An unusual case of multiple streamers or filaments with the characteristic mare's tail pattern in vertical section has been observed by radar where the generating elements were condensation trails laid by high-altitude aircraft. The contrails were laid perpendicular to the wind, and, as they drifted, a multitude of streamers formed along each trail. The streamers extended from 9 km to the ground. RHI and PPI photographs at X and S band taken over a 2-hr period show the three-dimensional shape of the streamers due to the wind shear. Doppler measurements were also taken. The resulting velocity spectra are very narrow indicating little or no turbulence. Reflectivity factors were measured at various altitudes and show a decrease in reflectivity with distance from the generating line. Fall velocities based on the slopes of the streamer patterns varied from 0.4 to 1.4 m/sec. In general, the characteristics of the precipitation streamers were quite similar to those previously measured in naturally occurring cloud forms such as cirrus uncinus.

Konrad, T. G.↗

Experimental study of the effect on span loading on aircraft wakes

Measurements were made in the NASA-Ames 40- by 80-foot wind tunnel of the rolling moment induced on a following model in the wake 13.6 spans behind a subsonic transport model for a variety of trailing edge flap settings of the generator. It was found that the rolling moment on the following model was reduced substantially, compared to the conventional landing configuration, by reshaping the span loading on the generating model to approximate a span loading, found in earlier studies, which resulted in reduced wake velocities. This was accomplished by retracting the outboard trailing edge flaps. It was concluded, based on flow visualization conducted in the wind tunnel as well as in a water tow facility, that this flap arrangement redistributes the vorticity shed by the wing along the span to form three vortex pairs that interact to disperse the wake.

Corsiglia, V. R.↗

Full scale upper surface blown flap noise

A highly noise suppressed TF 34 engine was used to investigate the noise of several powered lift configurations involving upper surface blown (USB) flaps. The configuration variables were nozzle type (i.e. slot and circular with deflector), flap chord length, and flap angle. The results of velocity surveys at both the nozzle exit and the flap trailing edge are also presented and used for correlation of the noise data. Configurations using a long flap design were 4 db quieter than a short flap typical of current trends in USB flap design. The lower noise for the long flap is attributed primarily to the greater velocity decay of the jet at the flap trailing edge. The full-scale data revealed substantially more quadrupole noise in the region near the deflected jet than observed in previous sub-scale tests.

Heidelberg, L. J.↗

The effect of wing dihedral and section suction distribution on vortex bursting

Eleven semi-span wing models were tested in the 1/8-scale model of the Langley V/STOL tunnel to qualitatively study vortex bursting. Flow visualization was achieved by using helium filled soap bubbles introduced upstream of the model. The angle of attack range was from 0 deg to 45 deg. The results show that the vortex is unstable, that is, the bursting point location is not fixed at a given angle of attack but moves within certain bounds. Upstream of the trailing edge, the bursting point location has a range of two inches; downstream, the range is about six inches. Anhedral and dihedral appear to have an insignificant effect on the vortex and its bursting point location. Altering the section suction distribution by improving the triangularity generally increases the angle of attack at which vortex bursting occurs at the trailing edge.

Washburn, K. E.↗

Flow visualization of leading-edge vortex enhancement by spanwise blowing

Flow visualization studies were conducted in a small pilot wind tunnel to determine qualitative effects of blowing a discrete jet essentially parallel to the leading edge of a 45 deg-swept trapezoidal wing featuring leading- and trailing-edge flaps. Test parameters included wing angle-of-attack, jet momentum coefficient, leading- and trailing-edge flap deflections, and nozzle chordwise displacement. Results of this study indicate that blowing from a reflection plane over the wing enhances the leading-edge vortex and delays vortex bursting to higher angles-of-attack and greater span distances. Increased blowing rates decrease vortex size, growth rate, and vertical displacement above the wing surface at a given span station and also extend the spanwise effectiveness of lateral blowing. Deflection of a leading-edge flap delays the beneficial effects of spanwise blowing to higher angles-of-attack. Nozzle chordwise locations investigated for the wing with and without leading-edge flap deflection appear equally effective in enhancing the separated leading-edge flow.

Erickson, G. E.↗

Six-color photometry of Iapetus, Titan, Rhea, Dione and Tethys

Six-color photometric observations made during Saturn's 1972/73 opposition enable us to separate the solar phase and orbital phase contributions to the observed light variations of Iapetus, Titan, Rhea, Dione and Tethys. Titan shows no orbital variations, but has phase coefficients which range from negligible values in the infrared to 0.014 mag/deg in the ultraviolet. Rhea has a bright leading side, a light curve amplitude of about 0.2 mag, and surprisingly large phase coefficients. Combined with other available information, the observations suggest a very porous, texturally complex surface layer. Dione has a leading side which is a few tenths of a magnitude brighter than the trailing side, but the light curve amplitude has little wavelength dependence and the phase coefficients are significantly smaller than those of Rhea, suggesting a less intricate surface texture. The leading side of Tethys is probably a few tenths of a magnitude brighter than the trailing side. Our Iapetus observations generally supplement the earlier work by Millis.

Noland, M.↗

Experimental study of the effect of span loading on aircraft wakes

Measurements were made in the NASA-Ames 40- by 80-Foot Wind Tunnel of the rolling moment induced on a following model in the wake 13.6 spans behind a subsonic transport model for a variety of trailing edge flap settings of the generator. It was found that the rolling moment on the following model was reduced substantially, compared to the conventional landing configuration, by reshaping the span loading on the generating model to approximate a span loading, found in earlier studies, which resulted in reduced wake velocities. This was accomplished by retracting the outboard trailing edge flaps. It was concluded, based on flow visualization conducted in the wind tunnel as well as in a water tow facility, that this flap arrangement redistributes the vorticity shed by the wing along the span to form three vortex pairs that interact to disperse the wake.

Corsiglia, V. R.↗

Noise reduction of EBF propulsive-lift systems

In a recently completed program, static and wind tunnel measurements have been made of the basic noise, noise reduction, and performance characteristics of externally blown flap (EBF) propulsive-lift systems. The static tests were performed on an outdoor model rig. Noise evaluations were made for parameters such as basic system geometry, flap slot dimension variation, elimination of flap slots, sweep angle variation, passive flap trailing edge modifications, active (blowing) trailing edge modifications, and for an ejector/decayer exhaust system. The wind tunnel evaluation determined forward speed effects on EBF systems noise characteristics. The results from the experimental programs are discussed as to their application to full scale short haul aircraft.

Gibson, J. S.↗

Full-scale upper-surface-blown flap noise

A highly noise-suppressed TF 34 engine was used to investigate the noise of several powered lift configurations involving upper-surface-blown (USB) flaps. The configuration variables were nozzle type (i.e. slot and circular with deflector), flap chord-length, and flap angle. The results of velocity surveys at both the nozzle exit and the flap trailing edge are used for correlation of the noise data. Configurations using a long flap design were 4 dB quieter than a short flap typical of current trends in USB flap design. The lower noise for the long flap is attributed primarily to the greater velocity decay of the jet at the flap trailing edge. The full-scale data revealed substantially more quadrupole noise in the region near the deflected jet than observed in previous sub-scale tests.

Heidelberg, L. J.↗

Study of viscous flow about airfoils by the integro-differential method

An integro-differential method was used for numerically solving unsteady incompressible viscous flow problems. A computer program was prepared to solve the problem of an impulsively started 9% thick symmetric Joukowski airfoil at an angle of attack of 15 deg and a Reynolds number of 1000. Some of the results obtained for this problem were discussed and compared with related work completed previously. Two numerical procedures were used, an Alternating Direction Implicit (ADI) method and a Successive Line Relaxation (SLR) method. Generally, the ADI solution agrees well with the SLR solution and with previous results are stations away from the trailing edge. At the trailing edge station, the ADI solution differs substantially from previous results, while the vorticity profiles obtained from the SLR method there are in good qualitative agreement with previous results.

Wu, J. C.↗

Vector thrust induced lift effects for several ejector exhaust locations on a V/STOL wind tunnel model at forward speed

The results and analysis of aerodynamic force data obtained from a small scale model of a V/STOL research vehicle in a low speed wind tunnel are presented. The analysis of the data includes the evaluation of aerodynamic-propulsive lift performance when operating twin ejector nozzles with thrust deflected. Three different types of thrust deflector systems were examined: 90 deg downward deflected nozzle, 90 deg slotted nozzle with boundary layer control, and an externally blown flap configuration. Several nozzle locations were tested, including over and underwing positions. The interference lift of the nacelle and model due to jet exhaust thrust is compared and results show that 90 deg turned nozzles located over the wing (near the trailing edge) produce the largest interference lift increment for an untrimmed aircraft, and that the slotted nozzle located under the wing near the trailing edge (in conjunction with a BLC flap) gives a comparable interference lift in the trimmed condition. The externally blown flap nozzle produced the least interference lift and significantly less total lift due to jet thrust effects.

Sharon, A. D.↗

A study of noise source location on a model scale augmentor wing using correlation techniques

An experimental investigation, conducted on a model-scale augmentor wing to identify the sources of far-field noise, is examined. The measurement procedure followed in the investigation involved the cross-correlation of far field sound pressures with fluctuating pressures on the surface of the augmentor flap and shroud. In addition pressures on the surfaces of the augmentor were cross-correlated. The results are interpreted as showing that the surface pressure fluctuations are mainly aerodynamic in character and are convected in the downstream direction with a velocity which is dependent on the jet exhaust velocity. However the far field sound levels in the mid and high frequency ranges are dominated by jet noise. There is an indication that in the low frequency range trailing edge noise, associated with interaction of the jet flow and the flap trailing edge, plays a significant role in the radiated sound field.

Wilby, J. F.↗

Development and demonstration of a flutter-suppression system using active controls

The application of active control technology to suppress flutter was demonstrated successfully in the transonic dynamics tunnel with a delta-wing model. The model was a simplified version of a proposed supersonic transport wing design. An active flutter suppression method based on an aerodynamic energy criterion was verified by using three different control laws. The first two control laws utilized both leading-edge and trailing-edge active control surfaces, whereas the third control law required only a single trailing-edge active control surface. At a Mach number of 0.9 the experimental results demonstrated increases in the flutter dynamic pressure from 12.5 percent to 30 percent with active controls. Analytical methods were developed to predict both open-loop and closed-loop stability, and the results agreed reasonably well with the experimental results.

Sandford, M. C.↗

Prediction of rotating-blade vortex noise from noise of nonrotating blades

Measurements were conducted in an acoustic wind tunnel to determine vortex noise of nonrotating circular cylinders and NACA 0012 airfoils. Both constant-width and spanwise tapered models were tested at a low turbulence level. The constant-diameter cylinder and constant-chord airfoil also were tested in the turbulent wake generated by an upstream cylinder or airfoil. Vortex noise radiation from nonrotating circular cylinders at Reynolds numbers matching those of the rotating-blade tests were found to be strongly dependent on surface conditions and Reynolds number. Vortex noise of rotating circular cylinder blades, operating with and without the shed wake blown downstream, could be predicted using data for nonrotating circular cylinders as functions of Reynolds number. Vortex noise of nonrotating airfoils was found to be trailing-edge noise at a time frequence equal to that predicted for maximum-amplitude Tollmein-Schlichting instability waves at the trailing edge.

Fink, M. R.↗

Test-section noise of the Ames 7 by 10-foot wind tunnel no. 1

An investigation was made of the test-section noise levels at various wind speeds in the Ames 7- by 10-Foot Wind Tunnel No. 1. No model was in the test section. Results showed that aerodynamic noise from various struts used to monitor flow conditions in the test section dominated the wind-tunnel background noise over much of the frequency spectrum. A tapered microphone stand with a thin trailing edge generated less noise than did a constant-chord strut with a blunt trailing edge. Noise from small holes in the test-section walls was insignificant.

Soderman, P. T.↗

OTW noise correlation for variations in nozzle/wing geometry with 5:1 slot nozzles

Acoustic data obtained from a model-scale study with 5:1 slot nozzles are analyzed and correlated in terms of apparent noise sources. Variations in nozzle geometry include roof angle and sidewall cutback. In addition, geometry variations in wing size and flap deflection are included. Three dominant noise sources were evident in the data and correlated: fluctuating lift noise, trailing edge noise and a redirected jet mixing noise that included the effect of reflection of jet noise by the surface. Pertinent variables in the correlations include the shear layer thickness and peak jet flow velocity at the trailing edge.

Vonglahn, U.↗