Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Low-speed wind tunnel experiments have been conducted to define methods for the manipulation of a generic fighter forebody's vortices in order to generate controlled yawing moments at high alpha. Attention is given to two vortex-control schemes: one involving independently controlled forebody tip strakes, and the other individually controlled blowing ports on the forebody. The most effective methods for forebody yawing-moment control were found to be the minimization of natural asymmetry with a pair of symmetrically mounted tip strakes, and the perturbation of the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗
NASA NTRS1995

The effect of adding roughness and thickness to a transonic axial compressor rotor

The performance deterioration of a high speed axial compressor rotor due to surface roughness and airfoil thickness variations is reported. A 0.025 mm (0.001 in.) thick rough coating with a surface finish of 2.54-3.18 RMS microns (100-125 RMS microinches) is applied to the pressure and suction surface of the rotor blades. Coating both surfaces increases the leading edge thickness by 10% at the hub and 20% at the tip. Application of this coating results in a loss in efficiency of 6 points and a 9% reduction in the pressure ratio across the rotor at an operating condition near the design point. To separate the effect of thickness and roughness, a smooth coating of equal thickness is also applied to the blade. The smooth coating surface finish is 0.254-0.508 RMS microns (10-20 RMS microinches), compared to the bare metal blade surface finish of 0.508 RMS microns (20 RMS microinches). The smooth coating results in approximately half of the performance deterioration found from the rough coating. Both coatings are then applied to different portions of the blade surface to determine which portions of the airfoil are most sensitive to thickness/roughness variations. Aerodynamic performance measurements are presented for a number of coating configurations at 60%, 80%, and 100% of design speed. The results indicate that thickness/roughness over the first 10% of blade chord accounts for virtually all of the observed performance degradation for the smooth coating, compared to about 70% of the observed performance degradation for the rough coating. The performance deterioration is investigated in more detail at design speed using laser anemometer measurements as well as predictions generated by a quasi-3D Navier-Stokes flow solver which includes a surface roughness model. Measurements and analysis are performed on the baseline blade and the full-coverage smooth and rough coatings. The results indicate that coating the blade causes a thickening of the blade boundary layers. The interaction between the rotor passage shock and the thickened suction surface boundary layer then results in an increase in blockage which reduces the diffusion level in the rear half of the blade passage, thus reducing the aerodynamic performance of the rotor.

Suder, Kenneth L.↗
NASA NTRS1959

Basic Pressure Measurements at Transonic Speeds on a Thin 45 deg Sweptback Highly Tapered Wing with Systematic Spanwise Twist Variations

Pressure distributions obtained in the Langley 8-foot transonic pressure tunnel on a thin, highly tapered, twisted, 450 sweptback wing in combination with a body are presented. The wing has a cubic spanwise twist variation from 0 deg. at 10 percent of the semispan to 60 at the tip. The tip is at a lower angle of attack than the root. Tests were made at stagnation pressures of 1.0 and 0.5 atmosphere, at Mach numbers from 0 0.800 to 1.200, and at angles of attack from -4 deg. to 20 deg.

Mugler, John P., Jr.↗
NASA NTRS1959

Basic Pressure Measurements at Transonic Speeds on a Thin 45 deg Sweptback highly Tapered Wing With Systematic Spanwise Twist Variations

Pressure distributions obtained in the Langley 8-foot transonic pressure tunnel on a thin highly tapered twisted 45 deg sweptback wing-body combination are presented. The wing has a quadratic spanwise twist variation from 0 deg at 10 percent of the semispan to 6 deg at the tip. The tip is at a lower angle of attack than the root. Tests were made at stagnation pressures of both 0.5 and 1.0 atmosphere at Mach numbers from 0.800 to 1.200 through an angle-of-attack range from -4 deg to 20 deg.

Mugler, John P., Jr.↗
NASA NTRS1988

Wake model for helicopter rotors in high speed flight

Two alternative approaches are developed to calculate blade-vortex interaction airloads on helicopter rotors: second order lifting-line theory, and a lifting surface theory correction. The common approach of using a larger vortex core radius to account for lifting-surface effects is quantified. The second order lifting-line theory also improves the modeling of yawed flow and swept tips. Calculated results are compared with wind tunnel measurements of lateral flapping, and with flight test measurements of blade section lift on SA349/2 and H-34 helicopter rotors. The tip vortex core radius required for good correlation with the flight test data is about 20 percent chord, which is within the range of measured viscous core sizes for helicopter rotors.

Johnson, Wayne R.↗
NASA NTRS1972

Static performance of a 13.97 cm (5.5 inch) diameter model VTOL lift fan

A tip-turbine-driven fan of the type currently being used in wind tunnel tests of VTOL lift fan models was tested. Values of thrust, weight flow, exit total and static pressure, exit swirl angle, and turbine temperature drop were measured as a function of fan speed for several inlet and exit configurations. A standard fan performance map was also obtained.

Lowe, W. H.↗
NASA NTRS1973

Hot-wire coil probe for high-speed flows

Small-diameter-wire coil probes developed for use in a hypersonic helium tunnel are discussed. The springlike properties of the coil minimize strain-gauge effects, and allow to use a higher length-to-diameter ratio for a given flow. In addition, the coil is more rugged for sudden flow changes, and since it can be mounted straight across the support tips, there is less support interference in cross flows. In addition to measuring fluctuating quantities in a boundary layer, the probes were used with a constant temperature anemometer for measuring mean mass flow profiles, and with a constant current anemometer for measuring mean total temperature profiles.

Weinstein, L. M.↗
NASA NTRS1986

Wind-tunnel investigation of the OMAC canard configuration

Wind-tunnel tests were conducted on a 0.175-scale model of the OMAC Laser 300 canard configuration in the NASA Langley 12-Foot Low-Speed Wind Tunnel to determine its low-speed high angel-of-attack aerodynamic characteristics. The Laser 300 is a general aviation turboprop pusher aircraft utilizing a canard configuration. The design incorporates a low forward wing and a high main wing with a leading-edge droop installed on the outboard panel and tip fins mounted on the wing tips. The model was tested over a range of -6 to 50-deg angle-of-attack and 20 to -20 deg sideslip. Static force and moment data were measured, and the longitudinal and lateral-directional characteristics were determined.

Ingram, W. C.↗
NASA NTRS1984

Solid/melt interface studies of high-speed silicon sheet growth

Radial growth-rate anisotropies and limiting growth forms of point nucleated, dislocation-free silicon sheets spreading horizontally on the free surface of a silicon melt have been measured for (100), (110), (111), and (112) sheet planes. Sixteen-millimeter movie photography was used to record the growth process. Analysis of the sheet edges has lead to predicted geometries for the tip shape of unidirectional, dislocation-free, horizontally growing sheets propagating in various directions within the above-mentioned planes. Similar techniques were used to study polycrystalline sheets and dendrite propagation. For dendrites, growth rates on the order of 2.5 m/min and growth rate anisotropies on the order of 25 were measured.

Ciszek, T. F.↗
NASA NTRS1992

Noise of two high-speed model counter-rotation propellers at takeoff/approach conditions

This paper presents acoustic results for two model counter-rotation propellers which were tested in the NASA Lewis 9- x 15-ft Anechoic Wind Tunnel. The propellers had a common forward rotor, but the diameter of the aft rotor of the second propeller was reduced in an effort to reduce its interaction with the forward rotor tip vortex. The propellers were tested at Mach 0.20, which is representative of takeoff/approach operation. Acoustic results are presented for these propellers which show the effect of rotor spacing, reduced aft rotor diameter, operation at angle-of-attack, blade loading, and blade number. Limited aerodynamic results are also presented to establish the propeller operating conditions.

Woodward, Richard P.↗
NASA NTRS2022

Combined Bluntness and Roughness Effects on Cones at Hypersonic Speeds

This computational study investigates the effects of discrete roughness elements on a blunt cone at zero degrees angle of attack in a Mach 6 flow. Motivation was provided by experiments conducted in the Air Force Research Laboratory Mach 6 High Reynolds Number facility on a 7-degree half-angle cone with a roughness array located at 45 degrees from the apex on two nose tips of different blutness but equivalent roughness Reynolds number. Transition was only affected on the blunter cone, indicating that the transition onset is associated with the combined effects of bluntness and roughness. The present study investigates the 15.24 mm nose radius, 420 azimuthal wavenumber case via Navier-Stokes computations of the laminar base flow and instability analysis. Plane-marching parabolized stability equations (PSE) and inflow-resolvent analysis based on the three-dimensional, harmonic linearized Navier-Stokes equations (HLNSE) are used to calculate the amplification of disturbances along the roughness wake as well as over the roughness nearfield. Results show that the roughness shape can have a great impact on the characteristics of the most amplified wake instabilities. For the experimental configuration with cubic roughness elements of 15 μ m height, the flow is marginally unstable. For prismatic elements of 20 μ m height, the PSE predicts a logarithmic disturbance amplification ratio of N = 5.6 along its wake, but this ratio increases to N = 9.6 when the amplification over the roughness and separation regions is included in the inflow-resolvent analysis.

Boundary-layer transition↗
NASA NTRS1959

Basic Pressure Measurements at Transonic Speeds on a Thin 45 deg Sweptback Highly Tapered Wing With Systematic Spanwise Twist Variations

Pressure distributions obtained in the Langley 8-foot transonic pressure tunnel on a thin, highly tapered, twisted, 45 deg sweptback wing in combination with a body are presented. The wing has a linear span-wise twist variation from 0 deg at 10 percent of the semispan to 6 deg at the tip. The tip is at a lower angle of attack than the root. Tests were made at stagnation pressures of 1.0 and 0.5 atmosphere, at Mach numbers from 0.800 to 1.200, and at angles of attack from -4 to 12 deg.

Mugler, John P., Jr.↗
NASA NTRS1981

Fiber optics for aircraft engine/inlet control

NASA programs that focus on the use of fiber optics for aircraft engine/inlet control are reviewed. Fiber optics for aircraft control is attractive because of its inherent immunity to EMI and RFI noise. Optical signals can be safely transmitted through areas that contain flammable or explosive materials. The use of optics also makes remote sensing feasible by eliminating the need for electrical wires to be connected between sensors and computers. Using low-level optical signals to control actuators is also feasible when power is generated at the actuator. Each application of fiber optics for aircraft control has different requirements for both the optical cables and the optical connectors. Sensors that measure position and speed by using slotted plates can use lossy cables and bundle connectors if data transfer is in the parallel mode. If position and speed signals are multiplexed, cable and connector requirements change. Other sensors that depend on changes in transmission through materials require dependable characteristics of both the optical cables and the optical connectors. A variety of sensor types are reviewed, including rotary position encoders, tachometers, temperature sensors, and blade tip clearance sensors for compressors and turbines. Research on a gallium arsenide photoswitch for optically switched actuators that operate at 250 C is also described.

Baumbick, R. J.↗
NASA NTRS1981

Core compressor exit stage study. Volume 4: Data and performance report for the best stage configuration

The core compressor exit stage study program develops rear stage blading designs that have lower losses in their endwall boundary layer regions. The test data and performance results for the best stage configuration consisting of Rotor-B running with Stator-B are described. The technical approach in this efficiency improvement program utilizes a low speed research compressor. Tests were conducted in two ways: (1) to use four identical stages of blading to obtain test data in a true multistage environment and (2) to use a single stage of blading to compare with the multistage test results. The effects of increased rotor tip clearances and circumferential groove casing treatment are evaluated.

Wisler, D. C.↗
NASA NTRS1982

Moving cracks in layered composites

A three-layered composite with a crack spreading in the center layer has been analytically examined to evaluate the effect of material nonhomogeneity on a constant velocity crack. Two different loading characteristics are considered. In the first case, crack motion is maintained by uniform tensile stresses. In the other, crack deformation is caused by anti-plane shear stresses. Galilean transformation and Fourier sine and cosine transforms are used to determine dynamic crack tip stress fields. Standard Fredholm integral equations yield the dynamic stress intensity factors. The results show that the intensity of local dynamic stresses increases or decreases with crack length to layer thickness as a function of the relative magnitudes of the adjoining layer's material properties. Crack speed tends to increase the effect of material nonhomogeneity.

Sih, G. C.↗
NASA NTRS1992

Effects of curvature and rotation on turbulence in the NASA low-speed centrifugal compressor impeller

The flow in the NASA Low-Speed Impeller is affected by both curvature and rotation. The flow curves due to the following: (1) geometric curvature, e.g. the curvature of the hub and shroud profiles in the meridional plane and the curvature of the backswept impeller blades; and (2) secondary flow vortices, e.g. the tip leakage vortex. Changes in the turbulence and effective turbulent viscosity in the impeller are investigated. The effects of these changes on three-dimensional flow development are discussed. Two predictions of the flow in the impeller, one with, and one without modification to the turbulent viscosity due to rotation and curvature, are compared. Some experimental and theoretical background for the modified mixing length model of turbulent viscosity will also be presented.

Moore, Joan G.↗
NASA NTRS1993

Experimental Evaluation of a Cooled Radial-inflow Turbine

Two 14.4 inch tip diameter rotors were installed and tested in the Small Engines Component Turbine Facility (SECTF) at NASA Lewis Research Center. The rotors, a solid and a cooled version of a radial-inflow turbine, were tested with a 15 vane stat or over a set of rotational speeds ranging from 80 to 120 percent design speed (17,500 to 21,500 rpm). The total-to-total stage pressure ratios ranged from 2.5 to 5.5. The data obtained at the equivalent conditions using the solid version of the rotor are presented with the cooled rotor data. A Reynolds number of 381,000 was maintained for both rotors, whose stages had a design mass flow of 4.0 Ibm/sec, a design work level of 59.61 Btu/lbm, and a design efficiency of 87 percent. The results include mass flow data, turbine torque, turbine exit flow angles, stage efficiency, and rotor inlet and exit surveys.

Tirres, Lizet↗