Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Smoothing methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Pin-loaded holes in large orthotropic plates

Pin-loaded holes commonly occur in engineering structures. However, accurate analysis of such holes presents formidable difficulties because of the load-dependent contact of the pin with the plate. Significant progress has recently been achieved in the analysis of holes in isotropic plates. This paper develops a simple and accurate method for the partial contact analysis of pin-loaded holes in composites. The method is based on an inverse formulation that seeks to determine loads in a given contact-separation configuration. A unified approach for all types of fit was used. Continuum solutions were obtained for infinitely large plates of various typical orthotropic properties with holes loaded by smooth rigid pins. These solutions were then compared with those for isotropic plates. The effects of orthotropy and the type of fit were studied through load-contact relationships, distribution of stresses and displacements, and their variation with load. The results are of direct relevance to the analysis and design of pin joints in composite plates.

Mangalgiri, P. D.↗
NASA NTRS1989

Analysis of extreme wind shear

New methods utilizing extreme value statistical theory are applied in the analysis of the largest wind component shear in a wind profile as a function of shear layer thickness and season. Seasonal variability of extreme shear decreases as the shear layer thickness decreases. Wind profile measurement system smoothing and its effect upon extreme wind shear statistics is simulated by application of digital low-pass filters to Jimsphere wind profiles.

Adelfang, Stanley I.↗
NASA NTRS1991

On-board congestion control for satellite packet switching networks

It is desirable to incorporate packet switching capability on-board for future communication satellites. Because of the statistical nature of packet communication, incoming traffic fluctuates and may cause congestion. Thus, it is necessary to incorporate a congestion control mechanism as part of the on-board processing to smooth and regulate the bursty traffic. Although there are extensive studies on congestion control for both baseband and broadband terrestrial networks, these schemes are not feasible for space based switching networks because of the unique characteristics of satellite link. Here, we propose a new congestion control method for on-board satellite packet switching. This scheme takes into consideration the long propagation delay in satellite link and takes advantage of the the satellite's broadcasting capability. It divides the control between the ground terminals and satellite, but distributes the primary responsibility to ground terminals and only requires minimal hardware resource on-board satellite.

Chu, Pong P.↗
NASA NTRS2009

Construction of Low Dissipative High Order Well-Balanced Filter Schemes for Non-Equilibrium Flows

The goal of this paper is to generalize the well-balanced approach for non-equilibrium flow studied by Wang et al. [26] to a class of low dissipative high order shock-capturing filter schemes and to explore more advantages of well-balanced schemes in reacting flows. The class of filter schemes developed by Yee et al. [30], Sjoegreen & Yee [24] and Yee & Sjoegreen [35] consist of two steps, a full time step of spatially high order non-dissipative base scheme and an adaptive nonlinear filter containing shock-capturing dissipation. A good property of the filter scheme is that the base scheme and the filter are stand alone modules in designing. Therefore, the idea of designing a well-balanced filter scheme is straightforward, i.e., choosing a well-balanced base scheme with a well-balanced filter (both with high order). A typical class of these schemes shown in this paper is the high order central difference schemes/predictor-corrector (PC) schemes with a high order well-balanced WENO filter. The new filter scheme with the well-balanced property will gather the features of both filter methods and well-balanced properties: it can preserve certain steady state solutions exactly; it is able to capture small perturbations, e.g., turbulence fluctuations; it adaptively controls numerical dissipation. Thus it shows high accuracy, efficiency and stability in shock/turbulence interactions. Numerical examples containing 1D and 2D smooth problems, 1D stationary contact discontinuity problem and 1D turbulence/shock interactions are included to verify the improved accuracy, in addition to the well-balanced behavior.

Wang, Wei↗
NASA NTRSDate not supplied

Validation Experiments for Turbulent Separation over an Axisymmetric Body of Revolution

Historically, the flow physics involved with most turbulent separated flows have presented fundamental challenges to validating numerical approaches. As recognized by the CFD Vision 2030 study commissioned by NASA, validation of Reynolds-averaged Navier-Stokes (RANS) models and other scale-resolving methods for turbulent separated flow requires data from advanced, high-fidelity experiments designed specifically for CFD implementation. In accordance with this effort, a new test platform, referred to as the NASA Axisymmetric Afterbody, was designed to obtain detailed measurements of the flow field undergoing a smooth, adverse pressure gradient induced separation for a fixed Reynolds number, Re = 180,000. The parametric body offers a range of flow states progressing from fully attached, to incipient separation, and finally to small-scale separated flow based on variable afterbody geometries. In an initial effort to evaluate RANS turbulence model capabilities, the present configurations of the axisymmetric model host a mild adverse pressure gradient over the contoured boattail section, inducing incipient turbulent separation, as well as a slightly larger adverse pressure gradient, inducing a small-scale region of turbulent separation. Experiments include steady pressure measurements and 2-D PIV to provide the preliminary dataset for simulation studies, which examine the effect of variable grid domains and RANS turbulence models. This is done in an effort to understand and evaluate the critical variability between solutions for the present model configurations. Results indicate potential discrepancies may be due to the effect of the square tunnel test section walls, relatively large blockage ratio, and slight variability in reference parameters. Ongoing work will focus on higher fidelity experimental campaigns to obtain surface flow visualizations and Stereo-Particle Image Velocimetry (SPIV) to deliver higher spatial resolution of the three-dimensional flow field to aid turbulence modelers.

Validation↗
DOE OSTI2025

Development and transferability of neural-network models for plasma-surface interactions

Plasma-surface interactions are increasingly critical to modern technologies; yet, accurate molecular dynamics simulations remain limited by the capabilities of interatomic potentials. Deep Potentials (DPs) promise to revolutionize the field by providing a systematic method for producing accurate interatomic potentials. The primary challenge of DP development is selecting a dataset, which efficiently spans the set of atomic environments one expects to encounter in the subsequent molecular dynamics simulations. The computational cost of density functional theory calculations, which are the typical basis for DP development, makes it impossible to directly verify the quality of a given DP. To address this challenge, we explore the development of a deep-learned interatomic potential, “DeepREBO,” trained to reproduce the behavior of the REBO2 empirical potential, enabling direct validation of training methodology and transferability. Using an active learning framework, we begin with a minimal dataset and iteratively expand it to train a Deep Potential-Smooth Edition model that faithfully reproduces REBO2 results for 25 eV hydrogen bombardment of diamond (001), a particularly challenging case. We show that small, carefully curated datasets can outperform large, unguided ones, with effective models requiring fewer than 15 000 snapshots. Subsequent transferability tests demonstrate that while DeepREBO generalizes well to diamond (111) surfaces, performance degrades for amorphous carbon or higher-energy impacts, highlighting the need for use-case-specific training data. We also evaluate methods to improve short-range repulsion. This study outlines best practices for training robust deep potentials and underscores the importance of dataset design for predictive plasma simulations.

Ab-initio molecular dynamics↗
DOE OSTI2023

Classification Analytics of Pu-239 and U-235 Source Signatures Using Gamma Spectral Regions

Machine learning detection methods using gamma signatures from spectral measurements of low-intensity Pu-239 and U-235 sources are studied. NaI detectors located at different distances fromthe source have been used to collect the training and independent testing data sets. The source is introduced via a shielded conduit into the facility where it is surrounded by 21 NaI detectors deployed over 6 x 6 meters area in the formation of two concentric circles and a spiral. The counts in gamma spectral regions associated with these two sources are estimated at 1 second intervals for each NaI detector, and are used as classifier features for detecting the source presence. Eight different classifiers with five basic properties — namely, smooth, non-smooth, statistical, structural, and hyper-parameter tuning — are trained and tested using the background and source measurements collected over multiple experimental runs. While the overall classifier performance improved as detectors closer to the source are used, some identically produced detectors under-performed but differently between two sources. Some classifiers achieved lower training error but their testing error based on independent measurements is higher for both sources. Overall, these results indicate significant over-fitting by these methods, and illustrate the complexity of training and selecting the machine learning methods to solve these detection problems.

Rao, Nageswara↗
DOE OSTI2023

BeyondPlanck: V. Minimal ADC Corrections for Planck LFI

We describe the correction procedure for Analog-to-Digital Converter (ADC) differential non-linearities (DNL) adopted in the Bayesian end-to-end BEYONDPLANCK analysis framework. This method is nearly identical to that developed for the official Planck Low Frequency Instrument (LFI) Data Processing Center (DPC) analysis, and relies on the binned rms noise profile of each detector data stream. However, rather than building the correction profile directly from the raw rms profile, we first fit a Gaussian to each significant ADC-induced rms decrement, and then derive the corresponding correction model from this smooth model. The main advantage of this approach is that only samples which are significantly affected by ADC DNLs are corrected, as opposed to the DPC approach in which the correction is applied to all samples, filtering out signals not associated with ADC DNLs. The new corrections are only applied to data for which there is a clear detection of the non-linearities, and for which they perform at least comparably with the DPC corrections. Out of a total of 88 LFI data streams (sky and reference load for each of the 44 detectors) we apply the new minimal ADC corrections in 25 cases, and maintain the DPC corrections in 8 cases. All these corrections are applied to 44 or 70 GHz channels, while, as in previous analyses, none of the 30 GHz ADCs show significant evidence of non-linearity. By comparing the BEYONDPLANCK and DPC ADC correction methods, we estimate that the residual ADC uncertainty is about two orders of magnitude below the total noise of both the 44 and 70 GHz channels, and their impact on current cosmological parameter estimation is small. However, we also show that non-idealities in the ADC corrections can generate sharp stripes in the final frequency maps, and these could be important for future joint analyses with the Planck High Frequency Instrument (HFI), Wilkinson Microwave Anisotropy Probe (WMAP), or other datasets. We therefore conclude that, although the existing corrections are adequate for LFI-based cosmological parameter analysis, further work on LFI ADC corrections is still warranted.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

In Tube Condensation Heat Transfer and Pressure Drop for R454B and R32—Potential Replacements for R410A

The heating, ventilation and air conditioning (HVAC) industry in the United States seeks near-term alternative refrigerants to replace R-410A in unitary equipment. Two potential replacement refrigerants are R-454B and R-32. It is of interest to investigate the capability and accuracy of existing heat exchanger design methods when applied to these replacement refrigerants. To that end, this work presents empirical condensation quasi-local heat transfer coefficient and pressure drop data for R-454B and R-32. These data were obtained in a $\frac{3}{8}$ in. (9.52 mm) outside diameter (OD) smooth copper tube with a wall thickness of 0.032 in. (0.81 mm). The experimental variables and their ranges included refrigerant absolute pressure ( 1960 ≤ P a b s ≤ 3196 kPa), condensation temperature ( 35 ≤ T c o n d ≤ 50 °C), mass flux ( 100 ≤ G ≤ 200 kg m -2 s -1 ), vapor quality ( 0 ≤ x ≤ 1 ), and heat flux ( 32.9 ≤ q ″ ≤ 62.97 kW m -2 ). It was found that the heat transfer correlation developed by Cavallini et al. Cavallini et al. (2006) predicted the experimental condensation heat transfer data, for both R-454B and R-32, with the greatest accuracy. Using the Cavallini et al. correlation, it was found that the mean absolute percentage error (MAPE) was 10.5% and 15.1% for R-454B and R-32, respectively. Additionally, the pressure drop correlation developed by Friedel Friedel (1979) predicted the experimentally determined pressure gradient with a MAPE of 7.7% and 5.5% for R-454B and R-32, respectively. These results will assist the practicing thermal engineer to choose the most appropriate design correlation for these near-term replacement refrigerants.

42 ENGINEERING↗
DOE OSTI2021

Modulating effect of evanescent waves on thin film growth

Atomic-scale smooth thin films are keys to successful integration and proper function of many multilayer-structured devices. However, the intrinsic islandlike growth mode prevents human beings from realizing such ultrasmooth films of many important functional materials. To solve this problem, we propose a negative entropy-infusing method that employs evanescent waves to enhance the downward interlayer diffusion of adatoms and thus transform the islandlike growth mode to the layer-by-layer growth mode. In this work, the formulas of the optical force and the lowered diffusion barrier were derived, and the application of this theory on a simplified example demonstrates significantly improved surface morphologies through numerical simulations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1985

Development of an impact- and solvent-resistant thermoplastic composite matrix, phase 3

The polyimide from BTDA 1,6-hexanediamine and m-phenylenediamine was selected from a prior study for the present study. Methods to prepare prepreg which would provide low void composites at low molding pressures from the thermoplastic polyimide were studied. Cresol solutions of the polyimide were applied to a balanced weave carbon fabric and the cresol removed prior to composite molding. Low void composites were prepared from smoothed prepregs at high pressures (34.5 MPa) and temperatures as low as 260 C. Lower molding pressures lead to higher void composites. Need for a lower melt viscosity in the neat resin is suggested as a requirement to achieve low void composites at low pressures. Some mechanical properties are included.

Delano, C. B.↗
NASA NTRS1990

Users manual for AUTOMESH-2D: A program of automatic mesh generation for two-dimensional scattering analysis by the finite element method

AUTOMESH-2D is a computer program specifically designed as a preprocessor for the scattering analysis of two dimensional bodies by the finite element method. This program was developed due to a need for reproducing the effort required to define and check the geometry data, element topology, and material properties. There are six modules in the program: (1) Parameter Specification; (2) Data Input; (3) Node Generation; (4) Element Generation; (5) Mesh Smoothing; and (5) Data File Generation.

Hua, Chongyu↗
NASA NTRS1991

Applications of diamond films and related materials; Proceedings of the 1st International Conference, Auburn, AL, Aug. 17-22, 1991

The present conference discusses the nucleation and growth of diamond from hydrocarbons, the cutting tool performance of CVD thick-film diamond, the characterization of CVD diamond grinding powder, industrial applications of crystalline diamond-coated tools, standardized SEM tribometry of diamond-coated substrates, residual stress in CVD diamond films, the optical properties of CVD diamond films, polycrystalline diamond films for optical applications, and diamond growth on ferrous metals. Also discussed are ion beam-irradiation smoothing of diamond films, electronic circuits on diamond substrates, diamond-laminated surfaces for evaporative spray cooling, electron devices based on the unique properties of diamond, diamond cold cathodes, thin-film diamond microstructure applications, Schottky diodes from flame-grown diamond, diamond films for thermionic applications, methods of diamond nucleation and selective deposition, high-rate/large-area diamond film production, halogen-assisted diamond growth, the economics of diamond technology, and the optical and mechanical properties of diamondlike films.

Tzeng, Yonhua↗
NASA NTRS1998

Surface Morphology of Undoped and Doped ZnSe Films

Rare-earth doped ions in polar II-VI semiconductors have recently played an important role in the optical properties of materials and devices. In this study, undoped ZnSe and erbium doped ZnSe films were grown by radio frequency (RF) magnetron sputtering method. Atomic Force Microscopy (AFM) was used together with optical microscopy and UV-Vis spectroscopy to characterize the films. Doped samples were found to have higher surface roughness and quite different surface morphology compared to that of undoped samples. The grown films generally show a relatively smooth and uniform surface indicating that they are of overall good quality. The impact of plasma etching on ZnSe:Er film examined under AFM is also discussed.

George, T.↗
NASA NTRS2004

Frequency Domain Calculations Of Acoustic Propagation

Two complex geometry problems are solved using the linearized Euler equations. The impedance mismatch method1 is used to impose the solid surfaces without the need to use a body-fitted grid. The problem is solved in the frequency domain to avoid long run times. Although the harmonic assumption eliminates all time dependence, a pseudo-time term is added to allow conventional iterative methods to be employed. A Jameson type, Runge-Kutta scheme is used to advance the solution in pseudo time. The spatial operator is based on a seven-point, sixth-order finite difference. Constant coefficient, sixth-derivative artificial dissipation is used throughout the domain. A buffer zone technique employing a complex frequency to damp all waves near the boundaries is used to minimize reflections. The results show that the method is capable of capturing the salient features of the scattering, but an excessive number of grid points are required to resolve the phenomena in the vicinity of the solid bodies because the wavelength of the acoustics is relatively short compared with the size of the bodies. Smoothly transitioning into the immersed boundary condition alleviates the difficulties, but a fine mesh is still required.

Lockard, David P.↗
NASA NTRS2004

An Ellipsoidal Particle-Finite Element Method for Hypervelocity Impact Simulation

A number of coupled particle-element and hybrid particle-element methods have been developed for the simulation of hypervelocity impact problems, to avoid certain disadvantages associated with the use of pure continuum based or pure particle based methods. To date these methods have employed spherical particles. In recent work a hybrid formulation has been extended to the ellipsoidal particle case. A model formulation approach based on Lagrange's equations, with particles entropies serving as generalized coordinates, avoids the angular momentum conservation problems which have been reported with ellipsoidal smooth particle hydrodynamics models.

Shivarama, Ravishankar↗
NASA NTRSDate not supplied

Validation Experiments of Incipient Turbulent Separation over an Axisymmetric Afterbody

Historically, the flow physics involved with most turbulent separated flows have presented fundamental challenges in validation between experimental and numerical approaches. As recognized by the CFD Vision 2030 study commissioned by NASA, validation of Reynolds-averaged Navier-Stokes (RANS) models and other scale-resolving methods for turbulent separated flow requires the support of advanced, high-fidelity experiments designed specifically for CFD implementation. In accordance with this effort, a new test platform, referred to as the NASA Axisymmetric Afterbody, was designed to obtain detailed information of the flow field over a smooth body, undergoing adverse pressure gradient induced separation for a fixed Reynolds number, Re = 180,000. The parametric body offers a range of flow states from fully attached,incipient separation, to fully separated flow based on variable afterbody geometries. In an initial effort to evaluate RANS turbulence model capabilities, the present configuration of the axisymmetric model features a mild adverse pressure gradient over the contoured boattail section, inducing incipient turbulent separation. Experiments include steady pressure measurements to serve as preliminary comparisons to simulation studies, which examine the effect of variable grid domains and RANS turbulence models, in an effort to understand and evaluate the critical variability between solutions for the present configuration. Results indicate potential discrepancies may be due to the effect of the square tunnel test section walls, relatively large blockage ratio, and inconsistent reference parameters. Ongoing work will focus on the experimental campaigns to obtain surface flow visualizations and high-resolution, off-body flow field measurements using Stereoscopic Particle Image Velocimetry (SPIV) and Laser Doppler Velocimetry (LDV) techniques to provide a detailed benchmark dataset to aid turbulence modelers.

axisymmetric afterbody↗
DOE OSTI2024

MFANS 2024 - Formally Proving Characteristics of Cyber-Physical Systems

Cyber-physical systems (CPS) are engineered systems that rely on the smooth integration of computational algorithms and physical elements. This integration presents new challenges for verifying that systems will behave as expected. The goal of this presentation is to present current challenges and potential solutions for the formal verification of cyber-physical systems. For cyber systems, formal methods refer to systematically rigorous mathematical techniques employed in the specification, development, analysis, and verification of both software and hardware systems. Recent advancements in computer science have yielded sophisticated tools specifically designed to address challenges associated with formal methods in complex systems. These tools leverage various foundational concepts such as logic, formal languages, program semantics, type systems, type theory, and automata theory. A notable achievement in the application of formal methods is the seL4 microkernel, claimed to be the first general-purpose operating-system kernel to be verified. Its proof implies the absence of bugs and guarantees that the kernel meets specifications. For physical systems, dynamic and control theory has a history of using rigorous analytic techniques to prove functional correctness. Lyapunov, optimal, classical, modern, and robust control theories all provide rigorous mathematical methods both to analyze system performance and to design controller that can be guaranteed to meet certain objectives. Recent computational techniques like level set theory and reachability analysis provide assertions that a system's state will avoid unsafe regions. Even though success has been independently achieved for cyber systems and physical systems, the integration of such systems creates new challenges. In particular, there is an obvious discrepancy between finite-state machines and infinite-state systems, resulting in different approaches for modeling and analyzing these system. While it is possible to simulate hybrid systems, this provides only a demonstration of a performance and not proof. For hybrid systems, current formal methods and system analysis approaches typically require a workarounds to work on hybrid systems like CPS. This paper will outline the state of the art and limits of current practice for formally verifying CPS and will identify possible research directions that require attention.

97 MATHEMATICS AND COMPUTING↗