Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Postbuckling of flat unstiffened graphite-epoxy plates loaded in shear

An experimental and analytical study was conducted of the postbuckling response and failure characteristics of 8-, 16-, and 24-ply unstiffened graphite/epoxy plates under shear loading, including orthotropic, quasi-orthotropic, entirely +, -45 deg ply, and (0/90)s-class plates. Postbuckling stiffness is noted to be influenced by the stacking sequence and by the inplane boundary condition imposed on the test section by a picture frame test fixture. The ratio of failure load to buckling load was higher for specimens that had higher width-to-thickness ratios. It is noted that high displacement gradients may induce transverse shear stresses, and that delamination was the failure mechanism for many of the 8-ply specimens. An adhesive failure between the composite specimen and metal edge reinforcements initiated failure of the 16- and 24-ply specimens.

Rouse, M.↗
NASA NTRS1984

Flat-plate solar array progress and plans

The results of research into the technology of flat-plate solar arrays undertaken in the Flat-Plate Solar Array Project under the sponsorship of the U.S. Department of Energy are surveyed. Topics examined include Si refinement, ribbon-sheet substrate formation, module process sequences, environmental isolation, module engineering and testing, and photovoltaic-array economics.

Callaghan, W. T.↗
NASA NTRS1985

High thermal capacity cold plate/hot plate

The results of an analytical study to determine the feasibility of a novel two-phase cold plate/hot plate (CPHP) are presented. A key feature of the CPHP is the use of capillary forces to separate the liquid and vapor phases and distribute the liquid over the evaporating/condensing surface. The liquid phase is held by capillary forces in a reservoir and is carried to the evaporating surface by a wick. The reservoir is replenished at intervals from a valved external liquid supply line. In the hot plate mode, liquid accumulates in the reservoir and is removed by an external condensate line. Performance requirements for the device were capability of handling a power density of 4 watts/sq cm, an outlet quality (percentage of vapor flow to total flow) greater than 90 percent, and operation in a 0-g environment. An analytical model of CPHP operation was developed which concentrated on the liquid and vapor flows. It was found that the liquid carrying capillary grooves of rectangular cross-section gave significantly better predicted performance than V-shaped grooves. Using the analytical model, capillary groove width and length, vapor channel dimensions, and other parameters were selected to meet the performance requirements with a 100-percent margin.

Hwangbo, H.↗
NASA NTRS1985

Accurate stratospheric particle size distributions from a flat plate collection surface

Flat plate particle collections have revealed the presence of a remarkable variety of both terrestrial and extraterrestrial material in the stratosphere. It is found that the ratio of terrestrial to extraterrestrial material and the nature of the material collected may vary significantly over short time scales. These fluctuations may be related to massive injections of volcanic ash, emissions from solid fuel rockets, or variations in the micrometeoroid flux. The variations in particle number density can be of great importance to the earth's atmospheric radiation balance, and, therefore, its climate. With the objective to assess the number density of solid particles in the stratosphere, an examination has been conducted of all particles exceeding 1 micron in average diameter for a representative suite of particles obtained from a single flat plate collection surface. Attention is given to solid particle size distributions in the stratosphere, and the origin of important stratospheric particle types.

Zolensky, M. E.↗
NASA NTRS1985

Dynamic ground effects on a two-dimensional flat plate

The effect of time-variant vortex shedding is simulated by a sequence of discrete vortices convecting downstream in the wake of a two-dimensional flat plate whose lifting condition is modeled by means of the quasi-vortex lattice method. The boundary condition of this problem is specified in such a way that the tangency condition on the surface of the flat plate is satisfied; the boundary condition also takes into account the effect of airfoil motion relative to the ground. Significant lift changes are shown to occur, due to the dynamic ground effect, that are crucial in aircraft takeoff and landing transitions.

Chen, Y.-S.↗
NASA NTRS1985

A diffuse plate boundary model for Indian Ocean tectonics

It is suggested that motion along the virtually aseismic Owen fracture zone is negligible, so that Arabia and India are contained within a single Indo-Arabian plate divided from the Australian plate by a diffuse boundary. The boundary is a zone of concentrated seismicity and deformation commonly characterized as 'intraplate'. The rotation vector of Australia relative to Indo-Arabia is consistent with the seismologically observed 2 cm/yr of left-lateral strike-slip along the Ninetyeast Ridge, north-south compression in the Central Indian Ocean, and the north-south extension near Chagos.

Wiens, D. A.↗
NASA NTRS1986

Brewster-Plate Spoiler for Laser Spectrometer

Oscillating Brewster plate reduces effects of unwanted interference fringes on absorption-spectroscopic measurements obtained with tuned diode lasers. Plate modulates optical-path length past several resonance peaks causing interference fringes to pass by rapidly and become blurred. Thus, fringe effects averaged out over time. Technique used at other wavelengths from ultraviolet to infrared and in spectrometers with short or long optical paths, including those with retroreflectors or multipass cells.

Webster, C. R.↗
NASA NTRS1986

Ion-Plated Soft Metallic Films Reduce Friction and Wear

Ion plating is ion-assisted or glow-discharge surface-deposition technique. In this process, ions or energetic atoms transfer energy, momentum, and charge to substrate and deposited surface film. Process controlled to modify physical characteristics of surface, subsurface chemical conditions, and surface and subsurface microstructures as well. Ion plating with such soft, thin metallic films as gold, silver, or lead has great potential for producing self-contained lubricating surfaces. Such films reduce friction, wear, and corrosion on sliding or rotating mechanical surfaces used in wide range of environments.

Spalvins, T.↗
NASA NTRS1986

Improved Orifice Plate for Spray Gun

Erratic spray pattern of commercial spray gun changed to repeatable one by simple redesign of two parts. In modified spray gun orifice plate and polytetrafluoroethylene bushing redesigned to assure centering and alignment with nozzle. Such improvement useful in many industrial applications requiring repeatable spray patterns. Might include spraying of foam insulation, paint, other protective coatings, detergents, abrasives, adhesives, process chemicals, or fuels. Unmodified spray gun produces erratic spray because lateral misalignment between orifice plate and nozzle.

Cunningham, W.↗
NASA NTRS1985

Effects of velocity profile and inclination on dual-jet-induced pressures on a flat plate in a crosswind

An experimental study was conducted to determine surface pressure distributions on a flat plate with dual subsonic, circular jets exhausting from the surface into a crossflow. The jets were arranged in both side-by-side and tandem configurations and were injected at 90 deg and 60 deg angles to the plate, with jet-to-crossflow velocity ratio of 2.2 and 4. The major objective of the study was to determine the effect of a nonuniform (vs uniform) jet velocity profile, simulating the exhaust of a turbo-fan engine. Nonuniform jets with a high-velocity outer annulus and a low-velocity core induced stronger negative pressure fields than uniform jets with the same mass flow rate. However, nondimensional lift losses (lift loss/jet thrust lift) due to such nonuniform jets were lower than lift losses due to uniform jets. Changing the injection angle from 90 deg to 60 deg resulted in moderate (for tandem jets) to significant (for side-by-side jets) increases in the induced negative pressures, even though the surface area influenced by the jets tended to reduce as the angle decreased. Jets arranged in the side-by-side configuration led to significant jet-induced lift losses exceeding, in some cases, lift losses reported for single jets.

Jakubowski, A. L.↗
NASA NTRS1985

Stress concentration around a small circular hole in the HiMAT composite plate

Anisotropic plate theory is used to calculate the anisotropic stress concentration factors for a composite plate (AS/3501-5 graphite/epoxy composite, single ply or laminated) containing a circular hole. This composite material is used on the highly maneuverable aircraft technology (HiMAT) vehicle. It is found that the anisotropic stress concentration factor could be greater or less than 3 (the stress concentration factor for isotropic materials), and that the locations of the maximum tangential stress points could shift with the change of fiber orientation with respect to the loading axis. The effect of hole size on the stress concentration factor is examined using the Point Stress Criterion and the Averaged Stress Criterion. The predicted stress concentration factors based on the two theories compared fairly well with the measured values for the hole size 0.3175 cm (1/8 in). It is also found that through the lamination process, the stress concentration factor could be reduced drastically, indicating an improvement in structural performance.

Ko, W. L.↗
NASA NTRS1985

Design of notched plates under compression

A failure criterion for notched plates in compression was developed. The criterion is based on experimentally observed kinking failure of fibers around a notch combined compressive and shear stresses. Experimental results for plates with a crack or a hole are used to verify the failure model, and design studies are performed to demonstrate the use of the model.

Guerdal, Z.↗
NASA NTRS1986

Equivalent plate analysis of aircraft wing box structures with general planform geometry

A new equilvalent plate analysis formulation is described which is capable of modeling aircraft wing structures with a general planform such as cranked wing boxes. Multiple trapezoidal segments are used to represent such planforms. A Ritz solution technique is used in conjunction with global displacement functions which encompass all the segments. This Ritz solution procedure is implemented efficiently into a computer program so that it can be used by rigorous optimization algorithms for application in early preliminary design. A direct method to interface this structural analysis procedure with aerodynamic programs for use in aeroelastic calculations is described. This equivalent plate analysis procedure is used to calculate the static deflections and stresses and vibration frequencies and modes of an example wing configuration. The numerical results are compared with results from a finite element model of the same configuration to illustrate typical levels of accuracy and computation times resulting from use of this procedure.

Giles, G. L.↗
NASA NTRS1986

Plate motions and deformations from geologic and geodetic data

A satellite laser ranging experiment conducted by NASA since 1972 has measured the relative motion between the North America and Pacific plates in California. Based on these measurements, the 896-km distance between San Diego and Quincy, California, is shortening at 62 + or - 9 mm/yr. This geodetic estimate is consistent with the rate of motion between the two plates, calculated from geological data to be 53 + or - 3 mm/yr averaged over the past few million years.

Jordan, T. H.↗
NASA NTRS1985

Observing tectonic plate motions and deformations from satellite laser ranging

The scope of geodesy has been greatly affected by the advent of artificial near-earth satellites. The present paper provides a description of the results obtained from the reduction of data collected with the aid of satellite laser ranging. It is pointed out that dynamic reduction of satellite laser ranging (SLR) data provides very precise positions in three dimensions for the laser tracking network. The vertical components of the stations, through the tracking geometry provided by the global network and the accurate knowledge of orbital dynamics, are uniquely related to the center of mass of the earth. Attention is given to the observations, the methodologies for reducing satellite observations to estimate station positions, Lageos-observed tectonic plate motions, an improved temporal resolution of SLR plate motions, and the SLR vertical datum.

Christodoulidis, D. C.↗
NASA NTRS1985

A clamped rectangular plate containing a crack

The general problem of a rectangular plate clamped along two parallel sides and containing a crack parallel to the clamps is considered. The problem is formulated in terms of a system of singular integral equations and the asymptotic behavior of the stress state near the corners is investigated. Numerical examples are considered for a clamped plate without a crack and with a centrally located crack, and the stress intensity factors and the stresses along the clamps are calculated.

Tang, R.↗
NASA NTRS1984

Stress concentration measurement in a rectangular plate using an array of embedded optical fibers

Embedded single mode optical fiber waveguide has been used to determine the two-dimensional stress distribution produced by point loading on a simply supported rectangular plate. Each of the fifty individual fibers in the rectangular grid array attached to the plate yields a measurement of the stress integrated along the length of that fiber on the specimen. By using information from all the fibers, both the functional form and the amplitude of the distribution may be determined. Limits on the dynamic range and spatial resolution are indicated. Applications in the measurement of internal stress and the monitoring of physically small critical structural components are suggested.

Claus, R. O.↗
NASA NTRS1986

Optical identifications of radio sources with accurate positions using the United Kingdom Schmidt Telescope (UKST) IIIa-J plates

Several programs are making use of UKST Sky Survey plates to identify southern radio sources. The fine-grain modern plates and accurate radio positions give a much improved identification rate. It seems that it will very soon be possible to determine whether or not there is a quasar redshift cut-off at z of about 4. There is an urgent need for more accurate fundamental reference star positions in the South.

Savage, A.↗