Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Plastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Strength, deformation, and equation of state of tungsten carbide to 66 GPa

Here, strength, texture, and equation of state of hexagonal tungsten monocarbide (WC) have been determined under quasi-hydrostatic and non-hydrostatic compression to 66 GPa using angle-dispersive X-ray diffraction in the diamond anvil cell. Quasi-hydrostatic compression in a Ne pressure medium demonstrates that nanocrystalline WC is slightly less incompressible than bulk-scale WC, with respective bulk moduli of K 0 = 377 ± 7 and 397 ± 7 GPa and pressure derivatives K 0 ’ = 3.8 ± 0.3 and 3.7 ±0.3. This decrease in incompressibility with grain size is similar to behavior observed in other ceramics. Under nonhydrostatic compression, WC supports a mean differential stress of ~12-15 GPa at plastic yielding, which occurs at ~30 GPa. Strength in WC is anisotropic, with the (001) plane supporting 29-42% higher stress than stresses calculated from mean strain. Simulations using an Elasto-ViscoPlastic Self-Consistent model indicate that strength inferred from lattice strain theory may be overestimated due to effects of plastic deformation. Plastic deformation generates a texture maximum near $\langle\bar{2}110\rangle$ in the compression orientation, initially through prismatic slip on the {$10\bar{1}0$}$\langle\bar{1}2\bar{1}0\rangle$ and {$10\bar{1}0$}$\langle0001\rangle$ slip systems, followed by activation of pyramidal slip on {$10\bar{1}1$}$\langle\bar{2}113\rangle$ at ~40-50 GPa.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Intermetallic particle heterogeneity controls shear localization in high-strength nanostructured Al alloys

The mechanical behavior of two nanocrystalline Al alloys, Al-Mg-Y and Al-Fe-Y, is investigated with in-situ micropillar compression testing. Both alloys were strengthened by a hierarchical microstructure including grain boundary segregation, nanometer-thick amorphous complexions, carbide nanorod precipitates with sizes of a few nanometers, and submicron-scale intermetallic particles. The maximum yield strength of the Al-Mg-Y system is measured to be 950 MPa, exceeding that of the Al-Fe-Y system (680 MPa), primarily due to a combination of more carbide nanorods and more amorphous complexions. Both alloys exhibited yield strengths much higher than those of commercial Al alloys, and therefore have great potential for structural applications. However, some micropillar specimens were observed to plastically soften through shear banding. Post-mortem investigation revealed that intermetallic-free deformation pathways of a few micrometers in length were responsible for this failure. Further characterization showed significant grain growth within the shear band. The coarsened grains maintained the same orientation with each other, pointing to grain boundary mechanisms for plastic flow, specifically grain rotation and/or grain boundary migration. Here, the presence of intermetallic particles makes it difficult for both matrix and intermetallic grains to rotate into the same orientation due to the different lattice parameters and slip systems. Therefore, we are able to conclude that a uniform distribution of intermetallic particles with an average spacing less than the percolation length of shear localization can effectively prevent the maturation of shear bands, offering a design strategy for high-strength nanocrystalline Al alloys with both high strength and stable plastic flow.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Creep and failure at metal-oxide interfaces

Small-scale bicrystal creep experiments were performed on contacts formed via in situ high-temperature diffusion bonding of metal-oxide interfaces including Ag-ZrO 2 , Pd-ZrO 2 , Pt-ZrO 2 , and Ag-high entropy oxide. This work characterizes deformation and failure at metal-oxide interfaces during mechanical loading. Interfacial sliding can be activated easily, while tensile interfacial creep was not observed at any condition of stress or temperature measured. Plastic strain, instead, localizes within the metal under tensile loading. A variety of mechanisms for plastic strain occur in the metal including lattice dislocation-mediated plasticity, twinning, low-angle grain boundary formation, and low-angle grain boundary creep. Surface and low-angle grain boundary diffusion occur under conditions where no metal-oxide tensile creep is observed, highlighting the significant differences in their interfacial mechanical response. High-temperature interfacial failure occurs when the mean curvature at the contact neck is approximately zero and the applied stresses comparable to brittle fracture stresses. The brittle fracture stresses were measured to be σ ƒ = 180 ± 90 MPa at the Ag-ZrO 2 interface at 225 °C, σ ƒ = 460 ± 160 MPa at the Pd-ZrO 2 interface at 680 °C, and σ ƒ = 640 ± 440 MPa at the Pt-ZrO 2 interface at 1010 °C.

Creep↗
DOE OSTI2021

Deformation and fracture behavior of a laser powder bed fusion processed stainless steel: In situ synchrotron x-ray computed microtomography study

Tensile plastic deformation and fracture behavior of a laser powder bed fusion processed 316L stainless steel alloy was investigated in situ using high-resolution synchrotron x-ray computed microtomography (sXCT). Three different cases were studied: (1) specimen A1, near full-density with initial porosity of 0.04%, (2) specimen B1, initial lack-of-fusion (LOF) porosity of about 3% with the major axis of defects aligned nearly perpendicular to the tensile loading direction (LD), and (3) specimen B, similar to B1 but with the major axis of LOF defects aligned nearly parallel to LD. The effects of type, density, and orientation of defects in as-printed samples on plastic deformation and failure modes were studied by analyzing sXCT image sequences and quantitative defect properties. Specifically, the evolutions of porosity, size, aspect ratio, and angle of gas pores and LOF defects were characterized as a function of applied strain. Moreover, interactions between as-printed defects and deformation-induced crack propagation were investigated. The tensile behavior of specimen A1 was comparable to that of a commercial wrought plate. Furthermore, the quantitative in-situ sXCT results showed a void-growth phenomenon in A1 but without noticeable coalescence, resulting in a ductile cup-cone failure. Specimen B1 showed damage-driven brittle failure with limited plasticity due to early and rapid propagation of open voids. On the other hand, specimen B, with a similar amount of LOF defects as B1, showed deceivingly strong and ductile tensile behavior similar to A1 without any major crack propagations due to the favorable orientation relationship between LOF defects and the LD.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Insights into the soft brittle-to-ductile transition from discrete dislocation dynamics

The Brittle-to-ductile transition (BDT) in body centered cubic metals exhibits a soft transition wherein the fracture toughness gradually rises to before the onset of ductility. The resultant brittle-to-ductile transition temperature can be described with an Arrhenius relationship whose activation energy is related to plasticity in the material. To provide further insight into the nature of the BDTT, in this work we utilized a discrete dislo- cation dynamics model with a crack to simulate the BDT and how it depends on the thermally activated nature of plasticity. The interrelationship between the BDT activation energy and the dislocation mobility parameters were determined via the calculation of first order sensitivity coefficients. This analysis allows us to demonstrate that the activation energy for the BDT is directly related to the activation energy for plasticity through an effective stress that defines this relationship. This effective stress physically is the average stress on the dislocations that move out of the crack. Lastly, we are able to show that this effective stress is dictated by the low temperature fracture toughness or cleave energy of the material and the source position, the latter of which can be affected by processing. Collectively, these results provide new insight into what controls the thermal activation of the BDT and what are the important parameters to control it.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effects of interstitial oxygen on ω transformations and twin formation in bcc NbTaTiHf multi-principal element alloy from first-principles

Transformation- and twinning-induced plasticity (TRIP and TWIP) have been reported to contribute to the low-temperature deformation of some body-centered cubic (bcc) multi-principal element alloys (MPEAs) containing large fractions of group IV transition metals. The influence of interstitial solutes on the mechanisms underlying these forms of plasticity, however, remains unclear. Using first-principles calculations, we study the effects of interstitial O atoms on the relative stability of bcc and ω phases and on unstable and twin boundary stacking fault energy profiles in a representative bcc MPEA with high group-IV elemental fraction: NbTaTiHf. We find that O additions generally promote the relaxation of ω configurations back to their parent bcc structure, therefore inhibiting ω transformation. Calculations of the Rice parameter for bulk bcc and phases, as well as bcc-ω interfaces, further show that ω formation is a potent embrittlement factor, an effect that is enhanced by O additions, suggesting that the formation of bcc-ω interfaces is energetically preferred over the formation of the bulk ω phase. By contrast, the Rice parameter for twin boundaries indicates that these interfaces do not embrittle the material, even with O atoms at twin boundaries, providing a more favorable pathway for plastic deformation compared to ω transformation.

Density functional theory↗
DOE OSTI2020

Simulation of axial tensile well deformation during reservoir compaction in offshore unconsolidated methane hydrate-bearing formation

Sand production encountered in the 2013 offshore field gas production tests at the Nankai Trough, Japan, could be attributed to well failure during reservoir compaction. In this study, well integrity under various reservoir compaction patterns for the Nankai Trough case is examined using a well-formation finite element model. Here, the modelling details include the inclusion of a cement sheath as well as the modelling of construction processes (such as cement shrinkage). Well elongation in the overburden layer becomes significant when the reservoir subsidence is localized near the wellbore under large depressurization. Results show that the maximum plastic deviatoric strain level in the cement could reach 0.7% when the maximum reservoir subsidence reaches 0.85 m and cement shrinkage is limited. When cement shrinkage rises to 0.75%, the maximum plastic deviatoric strain increases to 2.4% as the cement accumulates additional plastic strain during shrinkage due to its deformation being constrained by the casing. In order to prevent the cement from failure, it might be effective to hold the pressure drawdown at a low level (e.g., several MPa) until the hydrate dissociation front advances to a certain radius from the well (e.g., a couple of tens of metres).

58 GEOSCIENCES↗
DOE OSTI2026

Bioelectrocatalytic conversion of CO₂ to PHA bioplastics using engineered methylotrophs

The sustainable generation of biodegradable plastics represents an opportunity to capture atmospheric CO 2 while reducing plastic waste accumulation in the environment. This study implements an integrated platform for bioelectrocatalytic CO 2 conversion to medium-chain-length polyhydroxyalkanoates (mcl-PHAs). Immobilizing cobalt phthalocyanine electrocatalysts on a covalent-organic framework in a gas recirculation electrolyzer enabled CO 2 -to-methanol conversion with a carbon conversion efficiency of 98%. Integration of polymer biosynthesis pathways enabled Methylotuvimicrobium alcaliphilum 20Z R to produce ~20% mcl-PHA of the dry cell weight with a CO 2 -to-bioproducts carbon conversion efficiency of 50%. This cell line was adapted to high sodium bicarbonate media, eliminating costly intermediate separation steps while improving economic potential. Transcriptomic analysis revealed sulfate transporters and peptidoglycan biosynthesis as key pathways involved in sodium bicarbonate halotolerance. Altogether, this research presents a foundation for integrating divergent chemical and biological processes into a transformative electrobiomanufacturing platform, addressing the need for alternative pipelines for generating valuable plastics and chemicals.

CO2 utilization↗
DOE OSTI2021

Determining failure properties of as-received and hydrided unirradiated Zircaloy-4 from ring compression tests

An integrated experimental and computational approach was developed to determine the plastic strain at fracture and to investigate the fracture energy of as-received and hydrided unirradiated Zircaloy-4 nuclear cladding tubes in the hoop direction at room temperature from ring compression testing (RCT). This work builds on previous methods in the literature that were developed to obtain the mechanical properties of nuclear cladding before fracture (Young’s modulus, yield stress, and strain-hardening parameters) from experimental RCT results and extends the characterization of this material class to include material failure properties. Furthermore, a ductile damage approach was developed and implemented in a validated finite element model to predict material failure, evaluate fracture energy, and quantify the plastic strain at fracture initiation. The hydrogen content of the Zircaloy-4 specimens was varied up to 610 wppm when the failure became brittle. As expected, increasing hydrogen content caused embrittlement of the Zircaloy-4 samples tested and the plastic strain at fracture and fracture energy to decrease.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The deformation and burst behavior of Zircaloy-4 cladding tubes with hydride rim features subject to internal pressure loads

This study is motivated by the desire to conduct a separate effects test replicating specific aspects of an in-pile pulse reactor test on high exposure light water reactor (LWR) fuel rods. The principal purpose of the tests was to determine whether temperature and or hydrogen concentration thresholds exist in assessing the vulnerability of a stress relieved zirconium alloy cladding tubes to low strain ruptures. A secondary objective was to determine whether observations of the cladding stress during deformation could aid in the understanding of the crack formation and propagation in cladding tubes with hydride rim features. Here, the study utilized artificially hydrided Zircaloy-4 cladding tubes and an isothermal, internal pressure test that was controlled with an in-situ strain measurement. The test results show a clear transition in failure vulnerability between room temperature and 150 °C. Below 150 °C, cladding tubes rupture at very low uniform plastic strain—even at relatively modest cladding hydrogen levels. At and above 150 °C, cladding tubes only rupture at low uniform plastic strain if the cladding hydrogen content is greater than 500 ppm and usually experience at least some modest amount of plastic deformation prior to rupture. Post-test metallographs from non-ruptured cladding tubes show numerous primary cracks forming in the hydride rim and arresting at the metal/hydride interface. This observation combined with the decrease in bulk yielding of hydrided cladding tubes when compared to fresh non-hydrided tubes leads to the conclusion that the fracture stress of the hydride rims is related to and bounded by the yield stress of the zirconium metal. Some evidence is presented for a change in crack propagation mechanism from one of void formation on hydride plates and linkage at temperatures below 150 °C to more classical ductile shearing beneath the primary crack tip at temperatures above 150 °C. This apparent change in crack propagation mechanism may help explain the observed temperature and hydrogen concentration thresholds.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Assessment of the impact of reactor residence time distribution on non-equilibrium product selectivity of polypropylene pyrolysis using reactive molecular dynamics simulations

Mass residence time distribution (RTD) is considered to be an important factor controlling the product selectivity in the pyrolysis of biomass and plastic wastes along with the pyrolysis chemistry. However, due to the complex pyrolysis chemistry of biomass and plastic waste, the coupling between the reaction chemistry, RTD, and product selectivity is challenging to understand. Here, we introduce a reaction molecular dynamics-based method to examine pyrolysis chemistry and species timescales to assess the impact of RTD on product selectivity and yield. To validate this method, reactive molecular dynamics simulations were conducted for polypropylene pyrolysis and its non-equilibrium product selectivity using 6 different RTDs. We find that the RTD and the reaction chemistry control the peak non-equilibrium product concentrations. The peak monomer (C 3 H 6 ) concentration during pyrolysis can be increased by up to 25 % by using a narrow RTD in the case of polypropylene pyrolysis. We also find that product selectivity is strongly affected by the average residence time and RTD. This coupling between the reaction chemistry, RTD, and product selectivity highlights the need to understand detailed reaction chemistry to control RTD and optimize non-equilibrium product selectivity during polymer and biomass pyrolysis. The present method provides a new way to design RTD for reactors to reach maximized product selectivity of plastic waste and biomass.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Modeling The Effects of Loading Scenario and Thermal Expansion Coefficient on Potential Failure of Cryo-compressed Hydrogen Vessels

A multiscale thermomechanical model for a simplified Type-3 cryogenic compressed hydrogen (H2) storage vessel is developed in this paper. The model accounts for the temperature-dependent elastic-plastic behavior of the vessel carbon/epoxy composite overwrap and aluminum alloy liner. The homogenized thermo-elastic-plastic behavior for the individual laminas of the vessel layup is obtained by an incremental Eshelby-Mori-Tanka approach associated with a micromechanical failure criterion to predict lamina failure while a standard elastic-plastic constitutive model is used to describe the behavior of a typical aluminum alloy assumed for the liner. The vessel response to external loadings is achieved by a finite element method. Four loading scenarios representing four thermomechanical cycles applied to the vessel are analyzed to evaluate constituent and lamina stresses as well as the associate failure criterion during the cycle according to these scenarios. The model can provide helpful guidance to mitigate thermal stresses by an adequate selection of loading scenario, optimizing the layup and by tailoring thermomechanical properties of the resin matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Phase field modeling of hydrogen release in nitrile-butadiene rubber composites after high-pressure hydrogen exposure

Experimental data showed that a simple diffusion model doesn’t suffice to explain the hydrogen (H 2 ) release kinetics in nitrile butadiene rubber (NBR) composites (one with no filler or plasticizer, one with plasticizer only, one with fillers and plasticizer, and one with fillers only) after exposed to hydrogen gas at a pressure of 27.6 MPa. In this work, we developed a phase field model that considers the effect of H 2 gas bubble evolution on H 2 release kinetics. With the model, we simulated the effect of thermodynamic and kinetics properties on the nucleation, growth, and shrinkage of gas bubbles and H 2 release kinetics during and after decompression. Here, the results demonstrated that 1) the model built upon certain thermodynamic and kinetics properties of a given material can well describe its H 2 release kinetics measured in experiments, and 2) the model can predict the gas bubble evolution, which is associated with the material property degradation and failures, with accurate thermodynamic and kinetics properties or H 2 release data from experiments.

08 HYDROGEN↗
DOE OSTI2020

The effect of microstructure on the relationship between grain boundary sliding and slip transmission in high purity aluminum

The relationship between grain boundary sliding (GBS) and slip transmission is investigated experimentally at grain boundaries in 99.99% aluminum with a through-thickness, coarse grained microstructure deformed in tension at 190 °C. Using scanning electron microscope enabled digital image correlation (SEM-DIC) and electron backscatter diffraction (EBSD), high resolution strain fields and microstructural information were measured to examine the influence of microstructural neighborhoods on interactions between GBS and slip transmission and strain localization. Several distinct cases are presented that highlight important microstructural factors that govern deformation near grain boundaries. The findings include (1) direct transmission and GBS were anti-compatible and facilitated by opposing boundary types (low misorientation and high energy grain boundaries respectively); (2) increased GBS activity was correlated with decreased indirect transmission behavior; (3) GBS accommodation at triple junctions was enabled by intragranular plasticity; and (4) the local intragranular plastic strain discontinuity between grains determined the magnitude of GBS gradients. Finally, this work provides insight into the nature of these mechanisms and can be used to identify strain transfer criteria that can lead to improved GBS-sensitive crystal plasticity models.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Gradient microstructure induced shear band constraint, delocalization, and delayed failure in CuZr nanoglasses

The mechanical properties of metallic glasses (MGs) can be significantly tuned by introducing a nanoscale glass-glass interface microstructure. Here, we design three types of Cu 64 Zr 36 MG seamless gradient microstructures by combining glassy grain sizes from 3 to 15 nm. We perform tensile loading molecular dynamics simulations on the named gradient nanoglasses to characterize their mechanical behavior. In all cases, results indicate the generation of gradient plasticity following the gradient in grain size, i.e. local plasticity increases from large to small grain size regions. Loading parallel to the gradient direction results in initial broad necking followed by catastrophic failure. In contrast, loading perpendicular to the gradient direction results in diffused shear band propagation from large to small grain size regions, delaying the generation of a dominant shear band and further delocalizing plastic deformation. In conclusion, the results demonstrate the synergistic effects generated by heterogeneous gradient designs in the mechanical behavior of metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Discrete stochastic model of point defect-dislocation interaction for simulating dislocation climb

Dislocation climb is an important high temperature process in metals plasticity, responsible for the phenomena such as creep, swelling, or hardening. Climb is defined by the ability of dislocations to leave their original glide plane by interacting with point defects. As such, dislocation climb is controlled by point defect diffusion/absorption/emission, all of which involve thermal activation. The existing thermodynamically consistent models for climb are generally formulated in a continuum framework, through the definition of effective defect fluxes and climb propensities in response to thermodynamic driving forces. However, the point-wise discrete nature of vacancies (and/or self-interstitials) confers a highly discrete nature to the climb dynamics, which is also strongly affected by elastic forces. The combination of discreteness, thermal activation, and elasticity makes this process too challenging for direct atomistic methods such as molecular dynamics. Here we develop a kinetic Monte Carlo model that captures vacancy generation and transport kinetics acting in conjuction with the evolving elastic fields provided by discrete dislocation dynamics simulations. The two models are coupled via the applied stresses and stress gradients generated by dislocation structures at vacancy locations. Our simulations reveal two surprising results. First that climb is dominated by vacancy emission even when the background vacancy concentration is much higher than the equilibrium one. And, second, that climb velocities might be much faster than otherwise believed when one uses the classical theories of climb. These effects are due to the locality of vacancy-dislocation processes, which are not captured in classical treatments that assume smooth vacancy fluxes and homogeneous concentrations. We apply the method to study elementary climb processes in body-centered cubic iron and furnish climb mobility functions to be used in parametric dislocation dynamics and/or crystal plasticity simulations. Here, we apply the technique to study non-conservative plastic bypass of spherical precipitates by edge dislocations and point out the differences between our discrete approach and existing continuum formulations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling shock-induced void collapse in single-crystal Ta systems at the mesoscales

Understanding the role of microstructural heterogeneities on the shock wave propagation and defect evolution behavior is essential to predicting the dynamic response of metals. Heterogeneities, such as voids, provide challenges to understanding the wave propagation behavior as the shock-void interaction can collapse the void and result in large plastic strains and significant heating (hot spot formation) in the metal. Accurate modeling of this phenomenon requires predicting the void collapse mechanisms and the related heat generation and dissipation mechanisms (hotspot formation) that determine the microstructure evolution. While molecular dynamics (MD) simulations can model the void collapse behavior, the time/length scale capabilities pose a challenge to connect with continuum models or the experimental scales. Here, this study presents the capability of the newly developed quasi-coarse-grained dynamics (QCGD) method that extends the MD simulations to larger system sizes and longer times to model this phenomenon. This study uses QCGD simulations to investigate the mechanisms of shock wave interactions with pre-existing voids in single-crystal Ta microstructures for variations in shock pressures, void size, and loading orientations. For a given orientation, the plasticity contributions and rates of void collapse are observed to vary with shock pressures and void size. The larger void sizes and higher pressures result in increased temperatures (hot spots) and faster void collapse rates and unravel the variations in the plasticity contributions. In addition, QCGD simulations investigate the post-collapse microstructure evolution as a release wave travels through the hot spot region. The simulations reveal that the reduction in temperatures due to heat dissipation initiates the dynamic recrystallization behavior in the hotspot regions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ study on the compression deformation of MoNbTaVW high-entropy alloy

The excellent mechanical properties of high-entropy alloys (HEAs) make them promising materials for advances in science and technology. However, the underlying mechanism of plastic deformation is not well understood. In situ experiments are urgently required to provide a fundamental understanding of the plastic deformation under high pressure. We performed in situ synchrotron X-ray diffraction (XRD) experiments to study compression deformation behavior of the HEA MoNbTaVW in a radial diamond anvil cell (rDAC). Our results show that the strength and ratio of the stress-to-shear modulus values are ~1.5 and 3 times that of pure tungsten (W), respectively. MoNbTaVW showed plastic deformation above 5 GPa and displayed a much stronger texture. In this work, we found that the active dislocation behavior is mainly responsible for the high strength in MoNbTaVW under compression. This unique technique opens a new avenue to investigate the in situ mechanical properties and their mechanism in other types of HEAs.

36 MATERIALS SCIENCE↗