Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Simultaneous X-ray and optical observations of the 7.7 second X-ray pulsar 4U 1626-67

Simultaneous X-ray and optical observations of the 7.7-s X-ray pulsar 4U 1626-67, obtained during May 29-31, 1978, reveal the presence of (1) intense, correlated optical and X-ray flares and (2) 7.7-s optical pulsations which agree in phase with the 1-3 keV X-ray pulsations to within 0.5 s (two standard deviations) and which agree in period to within 0.001 s (one standard deviation). From these data it is concluded that a substantial fraction (a minimum of 8%) and possibly all of the optical emission is produced from within approximately 0.5 light sec or 1.5 x 10 to the 10th cm of the neutron star. Furthermore, the data rule out the possibility that this optical emission comes from the X-ray heated surface of a degenerate or nondegenerate dwarf companion. It most likely comes from an accretion disk.

Mcclintock, J. E.↗
NASA NTRS1980

Simultaneous X-ray and optical observations of rapid variability in Scorpius X-1

Copernicus and SAS-3 observations of Sco X-1 during very active states show strong and rapid X-ray flickering with time scales as short as 20 sec. Simultaneous optical photometry reveals similar and remarkably well correlated flickering of lower amplitude. The level of correlation decreases when the X-ray source becomes fainter, but optical and X-ray fluxes, averaged over 1 min, are usually well correlated for B magnitudes less than 12.9. Cross-correlation analysis of the data during periods of high activity shows no really significant time delay between X-ray and optical features, although the cross-correlation function peaks systematically for positive lag values (optical following X-rays). The amplitude of the X-ray flickering exhibits a strong energy-dependence consistent with the well-known intensity versus spectral-hardness relation derived from previous observations. The highly correlated optical activity is interpreted as due to reprocessing of X-ray photons in the binary system.

Ilovaisky, S. A.↗
NASA NTRS1979

Fiber optic combiner and duplicator

The investigation of the possible development of two optical devices, one to take two images as inputs and to present their arithmetic sum as a single output, the other to take one image as input and present two identical images as outputs is described. Significant engineering time was invested in establishing precision fiber optics drawing capabilities, real time monitoring of the fiber size and exact measuring of fiber optics ribbons. Various assembly procedures and tooling designs were investigated and prototype models were built and evaluated that established technical assurance that the device was feasible and could be fabricated. Although the interleaver specification in its entirety was not achieved, the techniques developed in the course of the program improved the quality of images transmitted by fiber optic arrays by at least an order of magnitude. These techniques are already being applied to the manufacture of precise fiber optic components.

Source record↗
NASA NTRS1981

Optical processing for landmark identification

A study of optical pattern recognition techniques, available components and airborne optical systems for use in landmark identification was conducted. A data base of imagery exhibiting multisensor, seasonal, snow and fog cover, exposure, and other differences was assembled. These were successfully processed in a scaling optical correlator using weighted matched spatial filter synthesis. Distinctive data classes were defined and a description of the data (with considerable input information and content information) emerged from this study. It has considerable merit with regard to the preprocessing needed and the image difference categories advanced. A optical pattern recognition airborne applications was developed, assembled and demontrated. It employed a laser diode light source and holographic optical elements in a new lensless matched spatial filter architecture with greatly reduced size and weight, as well as component positioning toleranced.

Casasent, D.↗
NASA NTRS1981

Simultaneous X-ray, ultraviolet, optical, and radio observations of the flare star Proxima Centauri

Results of coordinated program of observations in the X-ray, UV, optical and radio regions of the dM5e flare star Proxima Centauri are presented. Simultaneous observations of the star were obtained on March 6 and March 7, 1979, by the Einstein Observatory IPC, the IUE SWP and LWR cameras at low dispersion, three ground-based optical telescopes in Australia and the Parkes 64-m radio telescope. A total of 10 radio bursts and six optical flares was detected during three nights of simultaneous radio and optical observations, which appear to be broadly correlated. A major X-ray flare event was detected with temperatures of 1.7 x 10 to the 7th and 1.2 x 10 to the 7th K during the rise and decay phases, respectively, respective X-ray fluxes of 3.0 x 10 to the -11th and 3.7 x 10 to the -11th ergs/sq cm per sec, and changes in spectral flux distribution. No radio, optical or UV flare emission corresponding to the X-ray flare was detected. The X-ray flare is interpreted in terms of an arch model with cooling predominantly by X-ray radiation, with an electron density of 1.0 x 10 to the 11th/cu cm during the decay phase and a total arch length comparable to the size of the star itself. The X-ray flare observed is thus more similar to a typical strong solar flare than heretofore seen on a flare star.

Haisch, B. M.↗
NASA NTRS1980

Optical alignment of high resolution Fourier transform spectrometers

Remote sensing, high resolution FTS instruments often contain three primary optical subsystems: Fore-Optics, Interferometer Optics, and Post, or Detector Optics. We discuss the alignment of a double-pass FTS containing a cat's-eye retro-reflector. Also, the alignment of fore-optics containing confocal paraboloids with a reflecting field stop which relays a field image onto a camera is discussed.

Breckinridge, J. B.↗
NASA NTRS1981

Optical recognition of statistical patterns

Optical implementation of the Fukunaga-Koontz transform (FKT) and the Least-Squares Linear Mapping Technique (LSLMT) is described. The FKT is a linear transformation which performs image feature extraction for a two-class image classification problem. The LSLMT performs a transform from large dimensional feature space to small dimensional decision space for separating multiple image classes by maximizing the interclass differences while minimizing the intraclass variations. The FKT and the LSLMT were optically implemented by utilizing a coded phase optical processor. The transform was used for classifying birds and fish. After the F-K basis functions were calculated, those most useful for classification were incorporated into a computer generated hologram. The output of the optical processor, consisting of the squared magnitude of the F-K coefficients, was detected by a T.V. camera, digitized, and fed into a micro-computer for classification. A simple linear classifier based on only two F-K coefficients was able to separate the images into two classes, indicating that the F-K transform had chosen good features. Two advantages of optically implementing the FKT and LSLMT are parallel and real time processing.

Lee, S. H.↗
NASA NTRS1982

Integrated optics technology study

The materials and processes available for the fabrication of single mode integrated electrooptical components are described. Issues included in the study are: (1) host material and orientation, (2) waveguide formation, (3) optical loss mechanisms, (4) wavelength selection, (5) polarization effects and control, (6) laser to integrated optics coupling,(7) fiber optic waveguides to integrated optics coupling, (8) souces, (9) detectors. The best materials, technology and processes for fabrication of integrated optical components for communications and fiber gyro applications are recommended.

Chen, B.↗
NASA NTRS1982

A digital optical torquemeter for high rotational speed applications

A digital optical torquemeter system designed for applications at high rotational speeds was fabricated and tested for zero stability at speeds up to 20,000 rpm. Data obtained in a spin rig and with simulated inputs demonstrate that the system is capable of measuring torque bar twist to within 0.03 degrees at speeds of 30,000 rpm. The optical system uses fiber optic bundles to transmit light to the torque bar and to silicon avalanche detectors. The system is microcomputer based and provides measurements of average torque and torque as a function of angular shaft position. The torquemeter requires no bearings or other contact between the rotating torque bar and the nonrotating optics, and tolerates movement of the torque bar as large as 1 mm relative to the optics.

Lesco, D. J.↗
NASA NTRS1983

Submillisecond Optical Knife-Edge Testing

Fast computer-controlled sampling of optical knife-edge response (KER) signal increases accuracy of optical system aberration measurement. Submicrosecond-response detectors in optical focal plane convert optical signals to electrical signals converted to digital data, sampled and feed into computer for storage and subsequent analysis. Optical data are virtually free of effects of index-of-refraction gradients.

Thurlow, P.↗
NASA NTRS1983

Application of optical fibers to wide-band differential interferometry

A broadband differential optical interferometer that uses an optical-fiber waveguide to transmit coherent light to a surface under inspection is discussed. Input laser light is coupled into two single-mode optical fibers in a stationary input optics enclosure. The fibers transmit the light to a small, remote detection head where it is used in a wide-band differential interferometer to detect continuous and pulsed surface-particle displacements. The effective separation between the input optics and the detection head allows simple surface scanning and probe alignment. Detection of simulated acoustic emission pulses by a prototype test unit is reported.

Garg, A. O.↗
NASA NTRS1983

Size of a gamma-ray burster optical emitting region

Measured limits on the quiescent optical and IR flux of the Nov. 19, 1978 gamma ray burster event are presented and used to establish a lower limit to the size of the optically emitting region. A total of 305 min of exposure was made, using a CCD with a UV cutoff at 3800 A. It was determined that the size of the optical emitting region is more than an order of magnitude larger than a neutron star. The size of the optical emitting region did not, however, coincide with that of the gamma ray emitting region, indicating that the optical emissions originate from a different area of the region, i.e., from a companion star or accretion disk rather than a neutron star.

Schaefer, B. E.↗
NASA NTRS1983

LU and Cholesky decomposition on an optical systolic array processor

Direct solutions of matrix-vector equations on an optical systolic array processor are considered. The solutions are discussed and a parallel algorithm for LU matrix decomposition that is very attractive for an optical realization is formulated. It is noted that when direct techniques are used, it is preferable to realize the matrix decomposition on an optical system and to utilize a digital processor for the solution of the simplified resultant matrix-vector problem. One method of realizing LU matrix decomposition on a new frequency-multiplexed optical systolic array matrix-matrix processor is described. A simple method for extending the process of LU decomposition to Cholesky decomposition on the optical processor is discussed.

Casasent, D.↗
NASA NTRS1984

Definition, analysis and development of an optical data distribution network for integrated avionics and control systems. Part 2: Component development and system integration

Fiber optic transmission is emerging as an attractive concept in data distribution onboard civil aircraft. Development of an Optical Data Distribution Network for Integrated Avionics and Control Systems for commercial aircraft will provide a data distribution network that gives freedom from EMI-RFI and ground loop problems, eliminates crosstalk and short circuits, provides protection and immunity from lightning induced transients and give a large bandwidth data transmission capability. In addition there is a potential for significantly reducing the weight and increasing the reliability over conventional data distribution networks. Wavelength Division Multiplexing (WDM) is a candidate method for data communication between the various avionic subsystems. With WDM all systems could conceptually communicate with each other without time sharing and requiring complicated coding schemes for each computer and subsystem to recognize a message. However, the state of the art of optical technology limits the application of fiber optics in advanced integrated avionics and control systems. Therefore, it is necessary to address the architecture for a fiber optics data distribution system for integrated avionics and control systems as well as develop prototype components and systems.

Yen, H. W.↗
NASA NTRS1982

Integration and compaction of optical systems in the mid-infrared

Problems in the design of optical systems for use with mid-IR (MIR; 10.6-micron) lasers are reviewed. The cryogenically operated lead-chalcogenide tunable diode lasers currently used as sources emit complex far-field patterns and require sophisticated beam collection, shaping, and guide optics. Since conventional optics using large mirrors and Ge lenses are often awkward to use and sensitive to vibration, and since optical fibers for the MIR have not been perfected, current research concentrates on hollow flexible rectangular metallic pipes. These pipes are shown to provide transmission of 95 percent or better over a 1-m length, with beam shaping and polarization control. The low transmission losses and wideband IR transmission of single-crystal alkali halides suggest the feasibility of their use in MIR optical fibers and waveguides.

Yu, C.↗
NASA NTRS1984

The use of an optical data acquisition system for bladed disk vibration analysis

A new concept in instrumentation was developed by engineers at NASA Lewis Research Center to collect vibration data from multi-bladed rotors. This new concept, known as the optical data acquisition system, uses optical transducers to measure bladed tip delections by reflection light beams off the tips of the blades as they pass in front of the optical transducer. By using an array of transducers around the perimeter of the rotor, detailed vibration signals can be obtained. In this study, resonant frequencies and mode shapes were determined for a 56 bladed rotor using the optical system. Frequency data from the optical system was also compared to data obtained from strain gauge measurements and finite element analysis and was found to be in good agreement.

Lawrence, C.↗
NASA NTRS1985

Fiber optic Raman thermometer for Space Shuttle main engine preburner profiling

The feasibility of combustion gas temperature measurements in the SSME fuel preburner using nonintrusive optical diagnostics was investigated. Temperature profiles are desired in the high pressure, hydrogen-rich preburner stream to evaluate designs to alleviate thermal stressing of the fuel pump turbine blades. Considering the preburner operating conditions and optical access restrictions, a spontaneous Raman backscattering system, implemented with optical fibers to couple to the combustion device, was selected as the most practical for gas temperature probing. A system is described which employs a remotely-located argon-ion laser to excite the molecular hydrogen Raman spectrum. The laser radiation is conveyed to the combustor through an optical fiber and focused through a window into the chamber by an optical head attached to the combustor. The gas temperature is determined from the distribution of rotational populations represented in the Raman spectrum.

Shirley, J. A.↗
NASA NTRS1984

Optically thick ablation fronts

The physical characteristics of optically thick ablation fronts such as interstellar clouds are analyzed. Attention is given to cold clumps in both planar and spherical geometries and modifications caused by accelerations in a gravitational field or by evaporation of the clumps when encountered hot gas. The effects of ablation on the appearance of the Rayleigh-Taylor instability are examined in both linear and nonlinear regimes. The results of the calculations are applied to the astrophysical phenomena of cold clumps immersed in a supersonic flow, optically thick jets, and ablation in stellar envelopes. Evaporation in an optically thick front is projected to be orders of magnitude larger than evaporation in electron-conduction fronts in optically thin conditions. The optically thick processes could then be useful for modeling flows from, e.g., newly formed stars and active galactic nuclei.

Konigl, A.↗