Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mexico”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mechanistic understanding of carbon mineralization in fracture systems using microfluidics

Carbon mineralization in mafic and ultramafic rocks presents an opportunity for permanent carbon storage in the Earth's subsurface. However, due to their lower permeability, pre-existing fracture networks are key for mineralization to occur. Therefore, to fully develop this technology, a mechanistic understanding of the mineralization behavior in fractures with the consideration of hydrodynamic components is required. We use high-pressure microfluidics to investigate key mechanisms influencing dissolution–precipitation in a fracture network. The experiments were conducted in micromodels made of natural rocks with a comb-shaped flow channel to mimic a fracture network. This enabled studying the effect of injection rate on coupled dissolution–precipitation in advection and diffusion-dominated flow paths. We used gypsum carbonation as an analog reaction to allow for realistic experimental time frames due to its rapid reaction kinetics. The experimental work is coupled with high-fidelity numerical simulations to enhance our understanding of the parameters affecting the mineralization reaction. Our results demonstrate the importance of flow rate on the rate and nature of the gypsum carbonation reaction revealing that higher flow rates enable deeper penetration of the mineral precipitation front into the dead-end channels. This is an important finding since for sustained mineralization in a fracture network, precipitation in dead-ends while still allowing for flowing fractures is critical. Detailed characterization of the precipitates showed that lower flow rates led to porous and loose precipitates in the form of aragonite while higher flow rates mimicked supersaturation behavior leading to the formation of calcite. The reactive transport simulations further demonstrated the significance of flow velocity in advection-dominated channels to influence the efficiency of carbon mineralization in diffusion-dominated channels, potentially clogging of dead-end channels. These findings highlight the need for coupling chemical, mechanical, and hydrodynamic processes to evaluate the nature and extent of carbon mineralization in fractured media critical for permanent storage in mafic and ultramafic formations. This research further highlights the need for more investigation in potential subsurface fracture generation techniques to aid carbon mineralization.

25 ENERGY STORAGE↗
DOE OSTI2025

Cobalt promotion of the InO x –TiO 2 heterojunction for dual photothermal reduction of CO 2

A series of cobalt-promoted indium–titanium composite oxides was synthesized using a microemulsion method. Their functional properties were investigated for the photothermal reduction of carbon dioxide. In this series, the indium content varied between 2.5 and 20%, while the cobalt percentage was kept constant at 4% throughout the series. In all cases, carbon monoxide formation occurred selectively through the reverse water gas shift reaction. The sample with 2.5% In maximized the synergistic use of the two energy sources, while the sample with 10% In showed the highest catalytic activity under both thermal and dual photo-thermo conditions. A physicochemical characterization was performed for all samples. The use of microscopy and X-ray absorption spectroscopy demonstrated that sub-nanometric indium entities, in combination with atomically dispersed cobalt oxide entities, achieved a balance between high thermal activity and significant synergy between light and heat in a catalytic process. The system with 10% indium is thus able to improve the thermal catalytic process through the use of light, providing an intensification procedure for the classic process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Beyond traditional diagnostics: Identifying active galactic nuclei using spectral energy distribution fitting in DESI data

Active galactic nuclei (AGN) are typically identified through their distinctive X-ray or radio emissions, mid-infrared (MIR) colors, or emission lines. However, each method captures different subsets of AGN due to signal-to-noise (S/N) limitations, redshift coverage, and extinction effects, underscoring the necessity for a multiwavelength approach for comprehensive AGN samples. This study explores the effectiveness of spectral energy distribution (SED) fitting as a robust method for AGN identification. Using CIGALE optical-MIR SED fits on DESI Early Data Release galaxies, we compare SED-based AGN selection (AGNFRAC ≥ 0.1) with traditional methods including BPT diagrams, WISE colors, X-ray, and radio diagnostics. The SED fitting identifies ∼70% of narrow- and broad-line AGN and 87% of WISE-selected AGN. Incorporating high S/N WISE photometry reduces star-forming galaxy contamination from 62% to 15%. Initially, ∼50% of SED-AGN candidates are undetected by standard methods, but additional diagnostics classify ∼85% of these sources, revealing low-ionization nuclear emission-line regions and retired galaxies potentially representing evolved systems with weak AGN activity. Further spectroscopic and multiwavelength analysis will be essential to determine the true AGN nature of these sources. SED fitting provides complementary AGN identification, unifying multiwavelength AGN selections. This approach enables more complete – albeit somewhat contaminated – AGN samples, which are essential for upcoming large-scale surveys where spectroscopic diagnostics may be limited.

Seyfert↗
DOE OSTI2024

Fault localization in a microfabricated surface ion trap using diamond nitrogen-vacancy center magnetometry

Here, as quantum computing hardware becomes more complex with ongoing design innovations and growing capabilities, the quantum computing community needs increasingly powerful techniques for fabrication failure root-cause analysis. This is especially true for trapped-ion quantum computing. As trapped-ion quantum computing aims to scale to thousands of ions, the electrode numbers are growing to several hundred, with likely integrated photonic components also adding to the electrical and fabrication complexity, making faults even harder to locate. In this work, we used a high-resolution quantum magnetic imaging technique, based on nitrogen-vacancy centers in diamond, to investigate short-circuit faults in an ion trap chip. We imaged currents from these short-circuit faults to ground and compared them to intentionally created faults, finding that the root cause of the faults was failures in the on-chip trench capacitors. This work, where we exploited the performance advantages of a quantum magnetic sensing technique to troubleshoot a piece of quantum computing hardware, is a unique example of the evolving synergy between emerging quantum technologies to achieve capabilities that were previously inaccessible.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Bridge connectivity effects on photoinduced ground-state electron spin polarization

Transient electron paramagnetic resonance (TREPR) spectroscopy has been used to probe photoinduced electron spin polarization in the recovered ground states of four radical-elaborated (CAT)Pt(bpy) donor-acceptor complexes (CAT = catechol; bpy = 4,4'-di-tert-butyl-2,2'-bipyridine). These complexes are comprised of one or two S = 1/2 nitronyl nitroxide radicals attached through different phenylethynyl bridges to the 3- or 3,6 positions of the CAT donor. In this paper, we demonstrate the effects of substitution patterns on the magnitude of the TREPR signal, thereby guiding future design principles for generating and understanding the origin of photoinduced electron spin polarization in these and related chromophores.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Low energy backgrounds and excess noise in a two-channel low-threshold calorimeter

Here, we describe observations of low energy excess (LEE) events, background events observed in all light dark matter direct detection calorimeters, and noise in a transition edge sensor based two-channel silicon athermal phonon detector with 375 meV baseline energy resolution. We measure two distinct LEE populations: “shared” multichannel events with a pulse shape consistent with substrate athermal phonon events and sub-eV events that couple nearly exclusively to a single channel with a significantly faster pulse shape. These “singles” are consistent with events occurring within the aluminum athermal phonon collection fins. Similarly, our measured detector noise is higher than the theoretical expectation. Measured noise can be split into an uncorrelated component, consistent with shot noise from small energy depositions within the athermal phonon sensor itself, and a correlated component, consistent with shot noise from energy depositions within the silicon substrate's phonon system.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Para-particle oscillator simulations on a trapped-ion quantum computer

Deformed oscillators allow for a generalization of the standard fermions and bosons, namely, for the description of para-particles. Such particles remain hypothetical and unobserved in nature; yet, they can model physical phenomena, such as topological phases of matter. Here, we report the digital quantum simulation of para-particle oscillators by mapping para-particle states to the state of a qubit register, which allows us to identify the para-particle oscillator Hamiltonian as an XY model and further digitize the system onto a universal set of gates. In both instances, the gate depth grows polynomially with the number of qubits used. To establish the validity of our results, we experimentally simulate the dynamics of para-fermions and para-bosons, demonstrating full control of para-particle oscillators on a quantum computer. Furthermore, we compare the overall performance of the digital simulation of dynamics of the driven para-Fermi oscillator to a recent analog quantum simulation result.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

The impact of pulse width modulation on heat accumulation in AlGaN channel HEMTs

The poor thermal properties of Aluminum–Gallium Nitride (AlGaN) channel High Electron Mobility Transistors (HEMTs) on sapphire limit the device’s maximum switching frequency due to high channel temperatures. Extracting the correct thermal time constants can provide guidelines for the device’s safe frequency operation. This study experimentally quantifies the impact of pulse width and duty cycle on the transient thermal dynamics of multi-finger AlGaN channel HEMTs. In most transient thermal metrology, lock-in averaging approaches are leveraged to increase signal-to-noise ratio and measure the device’s relative temperature rise. Assuming no heat accumulation, the temperature rise is used to quantify the device’s thermal resistance under continued pulsed biasing. For devices grown on sapphire substrates, however, heat accumulation leads to elevated reference temperatures and causes the differential measurement to underestimate the peak temperature. This study demonstrates the capability of transient Gate Resistance Thermometry (tGRT) to measure the absolute temperature, which is required to precisely evaluate the device’s thermal resistance. When an absolute temperature measurement is not feasible (such as thermoreflectance imaging), a solution is proposed to derive the peak temperature under pulsed biasing based on the differential temperature under pulsing and the steady-state thermal resistance (which is typically easier to obtain). Finally, additional tGRT (without averaging) is performed to demonstrate the temperature-dependent thermal time constants required to minimize heat accumulation effects.

Field effect transistors↗
DOE OSTI2025

Noise limits for dc SQUID readout of high- Q resonators below 300 MHz

We present the limits on noise for the readout of cryogenic high-Q resonators using dc Superconducting Quantum Interference Devices (SQUIDs) below 300 MHz. This analysis uses realized first-stage SQUIDs (previously published), whose performance is well described by Tesche–Clarke (TC) theory, coupled directly to the resonators. We also present data from a prototype second-stage dc SQUID array designed to couple to this first-stage SQUID as a follow-on amplifier with high system bandwidth. This analysis is the first full consideration of dc SQUID noise performance referred to a high-Q resonator over this frequency range and is presented relative to the standard quantum limit. We include imprecision, backaction, and backaction–imprecision noise correlations from TC theory, the noise contributed by the second-stage SQUIDs, wiring, and preamplifiers, and optimizations for both on-resonance measurements and off-resonance scan sensitivity. This architecture has modern relevance due to the increased interest in axion searches and the requirements of the DMRadio-m 3 axion search, which uses dc SQUIDs in this frequency range.

Bosons↗
DOE OSTI2026

Prospects for detecting UF6 hydrolysis intermediates by mass spectrometry, resonance Raman, and NQR spectroscopy

Simulations are performed to consider several spectrometric and spectroscopic candidates for elucidating the mechanism of the hydrolysis of uranium hexafluoride (UF6). This study is among the first to benchmark the def-mTZVP basis sets for actinide-containing molecules, and it is shown to be a suitable basis set for surveying geometrical structures and vibrational spectra when used in conjunction with density functional theory. An experiment is proposed coupling mass spectrometric ion selection with vibrational spectroscopy, and supporting infrared and Raman spectral simulations demonstrate that ionization blue-shifts bands and can change their qualitative features. Ultraviolet resonance Raman is shown to have good prospects for discriminating U–O–U bridged intermediates, evidence for which was observed recently [L. E. McNamara et al., J. Phys. Chem. A 130, 775–786 (2026)]. As a more speculative approach, we also consider the prospect of addressing 233U or 235U nuclei by quadrupole resonance (NQR) spectroscopy for assigning early stage intermediate complexes. In doing so, we provide a first order-of-magnitude estimate for the collision-induced NQR signal for the UF6 dimer, which is of interest for the interpretation of a fast decoherence time observed in liquid-phase nuclear magnetic resonance. Having provided critical insights into the formation and stability of UF6 hydrolysis intermediates in previous studies, this computational spectroscopy survey is expected to help guide and expedite future laboratory campaigns.

Lutz, Jesse J. [Center for Computing Research, San↗
DOE OSTI2026

Platform for 100 s Mbar equation of state measurements on the National Ignition Facility

Equation of state (EOS) measurements in the 100 s Mbar range are needed to underwrite models employed in the simulation of high energy density plasmas. To this end, a platform has been developed for fielding on the National Ignition Facility, capable of producing high-quality impedance match EOS data, wherein a planar, high-pressure, steady shock is driven into a sample package, and sample and reference standard shock velocities are measured. This platform, dubbed planar high pressure, or PHP, was fielded with an initial proof-of-concept shot in January 2023. The first PHP shot, aiming to study gold, demonstrated a pressure close to 400 Mbar, two orders of magnitude higher than previously reported gold EOS data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Multiscale and multidimensional modeling of particle acceleration and transport in solar flares

Multi-messenger, multi-viewpoint, and time-resolved observations of solar flares are now providing unprecedented constraints on particle acceleration sites, energy conversion, and energy transport. The interpretation of current observations, including microwave imaging spectroscopy from EOVSA, hard x-ray (HXR) imaging from Solar Orbiter/STIX, gamma-ray diagnostics from Fermi, and in situ measurements from Parker Solar Probe and Solar Orbiter, collectively demands modeling frameworks that go beyond traditional spatially unresolved, one-zone models or single-mechanism descriptions. This review surveys multiscale and multidimensional modeling approaches, including kinetic, magnetohydrodynamic (MHD), and macroscopic particle models, that are being developed to meet the need. Kinetic simulations reveal that three-dimensional (3D) effects, including field-line chaos and self-generated turbulence, are essential for sustained power-law particle acceleration. MHD simulations now capture flux-rope eruptions, plasmoid-unstable current sheets, and turbulent flare regions in realistic magnetic topologies. Macroscopic models coupling MHD with energetic-particle models produce spatially resolved electron distributions and synthetic HXR and microwave emissions for direct comparison with observations. Despite these advances, outstanding challenges remain in bridging kinetic and global scales, improving MHD simulations and macroscopic particle models, and achieving quantitative model-observation closure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Application of an Empirical Density Law via Python for Aqueous Plutonium Chloride Systems for MCNP6

Criticality safety models for aqueous plutonium chloride systems often contain a significant bias due to assumptions in material compositions. These systems are currently modeled as a fictitious metal-water mixture because little is known about the true solution density. Furthermore, no predictive density tools or capabilities for modeling aqueous plutonium chloride systems are approved for use at Los Alamos National Laboratory. Recent density measurements of this ternary system (PuCl 3 -HCl-H 2 O) have allowed for the development of a more realistic density law, which is applied in this work via an empirical method based in Python. This tool, entitled PuCS (Plutonium Chloride Solution tool) may be used to determine solution density and composition based on the plutonium content, acid content, and temperature for MCNP6 inputs. PuCS has been found to predict density within 2% of experimental data. In conclusion, MCNP6 calculations have found that crediting minimal amounts of free acid (0.5 M) may correspond to a ~12% decrease in peak reactivity in comparison to current modeling methods.

42 ENGINEERING↗
DOE OSTI2025

Foliar elemental distribution in Blepharidium guatemalense assessed by synchrotron X-ray fluorescence spectroscopy and colorimetric optical microscopy

The hyperaccumulation phenomenon holds significant potential for Ni agromining in ultramafic areas; however, data on tropical hyperaccumulator species, particularly regarding metal distribution and tolerance mechanisms, remain scarce. Here, this study characterized the foliar elemental distribution of Blepharidium guatemalense, analyzed its metal localization at both tissue and cellular levels, and quantified its Ni accumulation when grown in Brazilian ultramafic soil. Plants were grown in pots for 90 days, and Ni concentrations in the aerial biomass and bio-ore were determined. Synchrotron-based micro-X-ray fluorescence (S-µXRF) was used to assess metal distribution in tissues, supplemented by microscopic examination with dimethylglyoxime (DMG) to visualize Ni accumulation in specific cell types. B. guatemalense reached 19,000 mg kg −1 Ni in leaves. Processing leaf biomass produced ash containing 24 wt% Ni, indicating promising metal-recovery potential for the species. S-µXRF revealed that Ni was predominantly localized in the central and secondary veins of the leaves, suggesting efficient vascular transport. Microscopic analysis using the colorimetric reagent DMG further showed that Ni accumulation occurs near the epidermis and phloem, suggesting that B. guatemalense employs specific physiological mechanisms for Ni translocation, potentially supporting both defense and growth functions. These results establish B. guatemalense as a promising candidate for large-scale Ni agromining in tropical regions.

36 MATERIALS SCIENCE↗
DOE OSTI2026

SALSAA: a statistical approach to line shapes from an average atom

Ion-Stark line broadening is a key density diagnostic for hot dense plasmas relevant to inertial fusion and astrophysics. It is caused by interactions of a radiating ion with nearby perturbing ions, whose electric microfields lead to changes in bound-bound transition energies. Ion-Stark broadening becomes increasingly difficult to compute for complex, many-electron ions with myriad transitions. In this paper, we propose a simplified approach to ion-Stark broadening based on self-consistent ion distributions and electronic structure from an average-atom model. We find that this approach reproduces the line shape predictions of one traditional method for high-n K-shell emission lines in aluminum ions with accuracy sufficient for density diagnostics in thermal plasmas with equal ion and electron temperatures. We expect that this approach can be extended to provide a reasonable picture of ion-Stark broadening in many-electron ions, enabling rapid calculations of line profiles in complex spectra.

average-atom↗
DOE OSTI2024

QCD evolution of entanglement entropy

Entanglement entropy has emerged as a novel tool for probing nonperturbative quantum chromodynamics (QCD) phenomena, such as color confinement in protons. While recent studies have demonstrated its significant capability in describing hadron production in deep inelastic scatterings, the QCD evolution of entanglement entropy remains unexplored. Here, in this work, we investigate the differential rapidity-dependent entanglement entropy within the proton and its connection to final-state hadrons, aiming to elucidate its QCD evolution. Our analysis reveals a strong agreement between the rapidity dependence of von Neumann entropy, obtained from QCD evolution equations, and the corresponding experimental data on hadron entropy. These findings provide compelling evidence for the emergence of a maximally entangled state, offering new insights into the nonperturbative structure of protons.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Post-inflationary enhancement of adiabatic perturbations in modular cosmology

We show that multi-field inflationary models with negligible turning in field space during inflation can lead to an effective sourcing of adiabatic from entropic perturbations afterthe end of inflation. We illustrate this general phenomenon with a detailed analysis of an inflationary model whose scalar potential is determined by modular invariance. Its entropic perturbations are frozen during inflation, but instead, they are converted into adiabatic perturbations in the first post-inflationary e-folds. The curvature power spectrum, giving rise to CMB fluctuations, reaches a novel and enhanced plateau in this process; we address the implications for the inflationary observables As , n s and r.

cosmological perturbation theory↗