Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LEAD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Application of the leading edge suction analogy to prediction of longitudinal load distribution and pitching moments for sharp edged delta wings

The leading-edge-suction analogy of Polhamus has been used to develop the longitudinal load distribution of the vortex lift for delta wings. This distribution is shown to be similar in shape to that of the potential-flow longitudinal loading for delta wings having aspect ratios of 2 or less. The totals of the two theoretical distributions for delta wings with an aspect ratio near 1 are in good agreement with the experimentally determined loadings over the angle-of-attack range from 0 to 30 deg. The corresponding predicted pitching moments show slightly more stability than those measured, because of loss of lift near the wing tips.

Snyder, M. H., Jr.↗
NASA NTRS1973

Beam lead forming tool

Tool was designed for table-top manual operation that can bend leads to any desired angle up to 90 degrees. It can be readily adapted to electrical, hydraulic, or pneumatic operation. This innovation may be of interest to electronics, sheet metal, and appliance industries.

Clemons, P. W.↗
NASA NTRS1972

A study of the microstructure and optical properties of thin lead-dielectric cermet films

A transmission electron microscopy study involving direct and replicating techniques is directed to a definition of the microstructure of radio frequency-sputtered, thin lead-dielectric cermet films. Once defined, this microstructure is used to obtain theoretical film refractive indices. The Maxwell Garnett theory provides a basis for the theoretical results. Measurements of film transmission and reflectivity are used to obtain rough experimental values for film refractive indices by the Tekucheva method. More exact values are obtained via ellipsometry. The rough Tekucheva values are used to determine the range over which computer calculations interpreting the ellipsometric results must be made. This technique yields accurate values for the film refractive indices.

Owen, R. B.↗
NASA NTRS1973

Leading edge serrations which reduce the noise of low-speed rotors

Acoustic effects of serrated brass strips attached near the leading edges of two different size rotors were investigated. The two bladed rotors were tested in hover. Rotor rotational speed, blade angle, serration shape, and serration position were varied. The serrations were more effective as noise suppressors at rotor tip speeds less than 135 m/sec (444 ft/sec) than at higher speeds. high frequency noise was reduced but the low frequency rotational noise was little affected. Noise reductions from 4 to 8 db overall sound pressure level and 3 to 17 db in the upper octave bands were achieved on the 1.52 m (5.0 ft) diameter rotor. Noise reductions up to 4 db overall sound pressure level were measured for the 2.59 m (8.5 ft) diameter rotor at some conditions.

Soderman, P. T.↗
NASA NTRS1972

Volatilized lead from Apollo 12 and 14 soils.

Lead in some Apollo-12 and -14 soils and breccias was volatilized under vacuum at temperature intervals of 0 to 600 C, 600 to 800 C, 800 to 1000 C, and 1000 to 1350 C. It is found that the Pb(206)/Pb(204) ratio increases and the Pb(207)/Pb(206) ratio decreases in the temperature range between 600 and 1000 C. The Pb(208)/Pb(206) ratios decrease from a value of 2 at 600 C to a value of 0.7 at 1350 C. These and other data suggest a secondary isochron age of about 4200 million years.

Doe, B. R.↗
NASA NTRS1973

Initial development of an ablative leading edge for the Space Shuttle orbiter.

A state-of-the-art preliminary design for typical wing areas is developed. Seven medium-density ablators (with/without honeycomb, flown on Apollo, Prime, X15A2) are evaluated. The screening tests include (1) leading-edge models sequentially subjected to ascent heating, cold soak, entry heating, post-entry pressure fluctuations, and touchdown shock, and (2) virgin/charred models subjected to bondline strains. Four materials (none molded) are found acceptable. The ESA 3560 HF and MOD 7 Hc (an AVCO 30 pcf elastomer) are selected. Roughness/recession degradation of low speed aerodynamics appears acceptable. The design, including attachments, substructure and joints, is presented.

Daforno, G.↗
NASA NTRS1973

High-speed leading edge problem.

The sharp leading edge problem has been studied for both monatomic and diatomic gases using the Boltzmann equation with the Bhatnagar-Gross-Krook type models as the governing equation and the discrete ordinate method with a closed-boundary value approach as a tool. Plate length relative to the freestream mean free path is taken to be 52. The gas-surface interaction law is assumed to be diffuse reflection. The local distribution functions of molecular velocities and internal energies (for the diatomic gas) for the entire flowfield have been calculated for a freestream Mach number of 6.1. Comparisons are made between the calculated results and experimental data.

Huang, A. B.↗
NASA NTRS1974

Wind tunnel tests of a full-scale model of a light twin-engine airplane with fixed auxiliary airfoil or leading-edge slot

An investigation has been conducted by means of wind-tunnel tests of a full-scale mockup of a light twin-engine airplane configuration to determine the effects of outboard partial-span slots and of auxiliary airfoils ahead of the leading edge of the wing in improving aerodynamic characteristics at high angles of attack. Both of the stall-control devices gave considerable improvement in high angle-of-attack characteristics with the auxiliary airfoil giving the more favorable results, but neither device performed as well as might have been expected.

Fink, M. P.↗
NASA NTRS1974

Improvement of electric characteristics of lead accumulators under the action of ultrasounds

Results are given of experiments conducted in order to improve the electric characteristics of lead accumulators by ultrasonic irradiation of their electrolytes. The experimental results discussed complete the research conducted on static Le2, Le3 and D. Quaiser cells whose solutions were irradiated beforehand with ultrasounds of the frequency of 1 MHz. It is demonstrated that the discharge currents and capacitances of the investigated cells keep to higher values even 1 year after ultrasonic irradiation of the electrolyte. The experimental results are discussed.

Mihu, V. P.↗
NASA NTRS1974

Initial development of an ablative leading edge for the space shuttle orbiter

A state-of-the-art preliminary design for typical wing areas is developed. Seven medium-density ablators (with/without honeycomb, flown on Apollo, Prime, X15A2) are evaluated. The screening tests include: (1) leading-edge models sequentially subjected to ascent heating, cold soak, entry heating, post-entry pressure fluctuations, and touchdown shock, and (2) virgin/charred models subjected to bondline strains. Two honeycomb reinforced 30 pcf elastomeric ablators were selected. Roughness/recession degradation of low speed aerodynamics appears acceptable. The design, including attachments, substructure and joints, is presented.

Daforno, G.↗
NASA NTRS1974

High current electrical lead

An electrical lead has insulators imbedded in an inner conductor rod to form an annulus between the rod and a surrounding outer sheath. This annular space is filled with gas which conducts heat and prevents electrical leakage.

Kaufman, W. B.↗
NASA NTRS1974

Extension of leading-edge-suction analogy to wings with separated flow around the side edges at subsonic speeds

A method for determining the lift, drag, and pitching moment for wings which have separated flow at the leading and side edges with subsequently reattached flow downstream and inboard is presented. Limiting values of the contribution to lift of the side-edge reattached flow are determined for rectangular wings. The general behavior of this contribution is computed for rectangular, cropped-delta, cropped-diamond, and cropped-arrow wings. Comparisons of the results of the method and experiment indicate reasonably good correlation of the lift, drag, and pitching moment for a wide planform range. The agreement of the method with experiment was as good as, or better than, that obtained by other methods. The procedure is computerized and is available from COSMIC as NASA Langley computer program A0313.

Lamar, J. E.↗
NASA NTRS1974

Cascade tests of serrated leading edge blading at high subsonic speeds

Cascade tests of two-dimensional fan rotor blade rows were performed to investigate the effects of leading edge serration on acoustic and aerodynamic performance. The test configurations covered a range of serration tooth geometries. Tests were performed to investigate effects of inlet air angle and velocity on performance. Aerodynamic performance was determined by flow surveys at the mid-span of the blade exit. Acoustic performance was determined by wake turbulence surveys and sound measurements in the semireverberent exhaust chamber. Measured acoustic and aerodynamic performance was comparable and indicated that a serration length of about six percent blade chord yields minimum noise generation and minimum total pressure losses.

Smith, E. G.↗
NASA NTRS1974

Tables for determining lead, uranium, and thorium isotope ages

Tables for determining lead, uranium, and thorium isotope ages are presented in the form of computer printouts. Decay constants, analytical expressions for the functions evaluated, and the precision of the calculations are briefly discussed.

Schonfeld, E.↗
NASA NTRS1975

An approximate closed-form solution for lead lag damping of rotor blades in hover

Simple stability methods are used to derive an approximate, closed-form expression for the lead-lag damping of rotor blades in hover. Destabilizing terms are shown to be a result of two dynamic mechanisms. First, the destabilizing aerodynamic forces that can occur when blade lift is higher than a critical value are maximized when the blade motion is in a straight line equidistant from the blade chord and the average direction of the air flow velocity. This condition occurs when the Coriolis terms vanish and when the elastic coupling terms align the blade motion with this least stable direction. Second, the nonconservative stiffness terms that result from pitch-flap or pitch-lag coupling can add or subtract energy from the system depending upon whether the motion of the blade tip is clockwise or counterclockwise.

Peters, D. A.↗
NASA NTRS1975

Prediction of unsteady aerodynamic loadings caused by leading edge and trailing edge control surface motions in subsonic compressible flow: Computer program description

A digital computer program has been developed to calculate unsteady loadings caused by motions of lifting surfaces with leading edge or trailing edge controls based on the subsonic kernel function approach. The pressure singularities at hinge line and side edges have been extracted analytically as a preliminary step to solving the integral equation by collocation. The program calculates generalized aerodynamic forces for user supplied deflection modes. Optional intermediate output includes pressure at an array of points, and sectional generalized forces. From one to six controls on the half span can be accommodated.

Redman, M. C.↗
NASA NTRS1975

Theoretical effect of modifications to the upper surface of two NACA airfoils using smooth polynomial additional thickness distributions which emphasize leading edge profile and which vary linearly at the trailing edge

An investigation was conducted on a CDC 7600 digital computer to determine the effects of additional thickness distributions to the upper surface of airfoils. The additional thickness distribution had the form of a continuous mathematical function which disappears at both the leading edge and the trailing edge. Results were obtained at a Mach number of 0.2 with an angle of attack of 6 deg. All calculations employed the full potential flow equations for two dimensional flow. The relaxation method of Jameson was used for solution of the potential flow equations. It is shown that increasing the thickness and variations in shape increases the lift and the adverse pitching moment coefficients.

Hague, D. S.↗