Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Cycle Simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

Adsorption modeling for off-gas treatment

Off-gas generated from the reprocessing of used nuclear fuel contains a mixture of several radioactive gases including {sup 129}I{sub 2}, {sup 85}Kr, HTO, and {sup 14}CO{sub 2}. Over the past few decades, various separation and recovery processes have been studied for capturing these gases. Adsorption data for gaseous mixtures of species can be difficult to determine experimentally. Therefore, procedures capable of predicting the adsorption behavior of mixtures need to be developed from the individual isotherms of each of the pure species. A particular isotherm model of interest for the pure species is the Generalized Statistical Thermodynamic Adsorption isotherm. This model contains an adjustable number of parameters and will therefore describe a wide range of adsorption isotherms for a variety of components. A code has been developed in C++ to perform the non-linear regression analysis necessary for the determination of the isotherm parameters, as well as the least number of parameters needed to describe an entire set of data. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigations into the Gas Phase Reactions of Zirconium Tetrachloride (ZrCl) from UNF Cladding

Zirconium-based cladding materials that surround used nuclear fuel (UNF) rods represent a significant fraction of the total amount of high level waste that must be disposed of in long term geological repositories. The decontamination, recovery and reuse of these materials would significantly reduce the high level waste associated with light water reactors and could provide a new source of hafnium free zirconium for the fabrication of new nuclear components. A step in a strategy to recycle zirconium from used cladding materials is the high yield chlorination of Zircaloys to produce zirconium tetrachloride (ZrCl{sub 4}). The ZrCl, is contaminated with other metal chloride species that originate from the alloying metals as well as contaminants from oxide layers on the cladding, trace fission products, fuel residues, activation byproducts, and tritium. The properties of these complex mixtures must be better understood before purification protocols can be developed that will allow zirconium chloride to be recycled further. First order thermodynamic modeling of high temperature mixtures of ZrCl, and other metal chlorides in the gas phase may not accurately predict their properties. Computational modeling studies indicate that mixed metal adducts may form under the conditions of sublimation-based purification protocols. In light of these predictions, alternate strategies may also be needed to obtain pure ZrCl, from such mixtures. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Updated Phase Calculation Method for Metallic Nuclear Fuel in BISON

Zirconium based metallic nuclear fuel undergoes significant redistribution of its constituents, resulting in several different phases present within a single fuel pin. Primarily dominated by the movement of zirconium in U-Pu-Zr and UZr fuels, phase changes result in a three (or more) zoned fuel structure clearly visible during post-irradiation examination (PIE). Each of these regions may posses differing material properties, requiring knowledge of the relative concentration of each phase in order for fuel performance codes to capture the relevant fuel behavior. The model described here was implemented into the fuel performance code BISON, similar to previous work for modeling zirconium redistribution in U-Pu-Zr fuel. However, the modules have since been updated with several key assumptions for easier use in future zirconium redistribution work and other phase-dependent material properties implementation, as discussed in the following sections. A new material model has been implemented in BISON to calculate the fractional phase concentrations as a function of temperature and zirconium concentration. Instead of smoothing the material properties to ensure numerical convergence, the new model smoothes the phase contributions directly, allowing easier implementation of material properties. By comparing the zirconium distribution for different smoothing parameters, it was shown that the smoothing parameters utilized here was adequate for the parameters of interest, while decreasing computational expense. The calculated phase information has been used to determine phase-dependent diffusivities, and is available for other phase-dependent properties. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Simulated Fission Gas Behavior in Silicide Fuel at LWR Conditions

As a promising candidate for the accident tolerant fuel (ATF) used in light water reactors (LWRs), the fuel performance of uranium silicide (U 3 Si 2 ) at LWR conditions needs to be well-understood. However, existing experimental post-irradiation examination (PIE) data are limited to the research reactor conditions, which involve lower fuel temperature compared to LWR conditions. This lack of appropriate experimental data significantly affects the development of fuel performance codes that can precisely predict the microstructure evolution and property degradation at LWR conditions, and therefore evaluate the qualification of U 3 Si 2 as an AFT for LWRs. Considering the high cost, long timescale, and restrictive access of the in-pile irradiation experiments, this study aims to utilize ion irradiation to simulate the inpile behavior of the U 3 Si 2 fuel. Both in situ TEM ion irradiation and ex situ high-energy ATLAS ion irradiation experiments were employed to simulate different types of microstructure modifications in U 3 Si 2 . Multiple PIE techniques were used or will be used to quantitatively analyze the microstructure evolution induced by ion irradiation so as to provide valuable reference for the development of fuel performance code prior to the availability of the in-pile irradiation data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Optimization of Depletion Modeling and Simulation for the High Flux Isotope Reactor

Monte Carlo based depletion tools used for the high-fidelity modeling and simulation of the High Flux Isotope Reactor (HFIR) come at a great computational cost; finding sufficient approximations is necessary to make the use of these tools feasible. The optimization of the neutronics and depletion model for the HFIR is based on two factors: (i) the explicit representation of the involute fuel plates with sets of polyhedra and (ii) the treatment of depletion mixtures and control element position during depletion calculations. A very fine representation (i.e., more polyhedra in the involute plate approximation) does not significantly improve simulation accuracy. The recommended representation closely represents the physical plates and ensures sufficient fidelity in regions with high flux gradients. Including the fissile targets in the central flux trap of the reactor as depletion mixtures has the greatest effect on the calculated cycle length, while localized effects (e.g., the burnup of specific isotopes or the power distribution evolution over the cycle) are more noticeable consequences of including a critical control element search or depleting burnable absorbers outside the fuel region.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Simulated performance of biomass gasification based combined power and refrigeration plant for community scale application

Thermal performance analysis and sizing of a biomass gasification based combined power and refrigeration plant (CPR) is reported in this study. The plant is capable of producing 100 kWe of electrical output while simultaneously producing a refrigeration effect, varying from 28-68 ton of refrigeration (TR). The topping gas turbine cycle is an indirectly heated all-air cycle. A combustor heat exchanger duplex (CHX) unit burns producer gas and transfer heat to air. This arrangement avoids complex gas cleaning requirements for the biomass-derived producer gas. The exhaust air of the topping GT is utilized to run a bottoming ammonia absorption refrigeration (AAR) cycle via a heat recovery steam generator (HRSG), steam produced in the HRSG supplying heat to the generator of the refrigeration cycle. Effects of major operating parameters like topping cycle pressure ratio (r{sub p}) and turbine inlet temperature (TIT) on the energetic performance of the plant are studied. Energetic performance of the plant is evaluated via energy efficiency, required biomass consumption and fuel energy savings ratio (FESR). The FESR calculation method is significant for indicating the savings in fuel of a combined power and process heat plant instead of separate plants for power and process heat. The study reveals that, topping cycle attains maximum power efficiency of 30%in pressure ratio range of 8-10. Up to a certain value of pressure ratio the required air flow rate through the GT unit decreases with increase in pressure ratio and then increases with further increase in pressure ratio. The capacity of refrigeration of the AAR unit initially decreases up to a certain value of topping GT cycle pressure ratio and then increases with further increase in pressure ratio. The FESR is found to be maximized at a pressure ratio of 9 (when TIT=1100°C), the maximum value being 53%. The FESR is higher for higher TIT. The heat exchanger sizing is also influenced by the topping cycle pressure ratio and GT-TIT.

09 BIOMASS FUELS↗

TRISO-Fuel Element Performance Modeling for the Hybrid LIFE Engine with Pu Fuel Blanket

A TRISO-coated fuel thermo-mechanical performance study is performed for the hybrid LIFE engine to test the viability of TRISO particles to achieve ultra-high burnup of a weapons-grade Pu blanket. Our methodology includes full elastic anisotropy, time and temperature varying material properties for all TRISO layers, and a procedure to remap the elastic solutions in order to achieve fast fluences up to 30 x 10{sup 25} n {center_dot} m{sup -2} (E > 0.18 MeV). In order to model fast fluences in the range of {approx} 7 {approx} 30 x 10{sup 25} n {center_dot} m{sup -2}, for which no data exist, careful scalings and extrapolations of the known TRISO material properties are carried out under a number of potential scenarios. A number of findings can be extracted from our study. First, failure of the internal pyrolytic carbon (PyC) layer occurs within the first two months of operation. Then, the particles behave as BISO-coated particles, with the internal pressure being withstood directly by the SiC layer. Later, after 1.6 years, the remaining PyC crumbles due to void swelling and the fuel particle becomes a single-SiC-layer particle. Unrestrained by the PyC layers, and at the temperatures and fluences in the LIFE engine, the SiC layer maintains reasonably-low tensile stresses until the end-of-life. Second, the PyC creep constant, K, has a striking influence on the fuel performance of TRISO-coated particles, whose stresses scale almost inversely proportional to K. Obtaining more reliable measurements, especially at higher fluences, is an imperative for the fidelity of our models. Finally, varying the geometry of the TRISO-coated fuel particles results in little differences in the scope of fuel performance. The mechanical integrity of 2-cm graphite pebbles that act as fuel matrix has also been studied and it is concluded that they can reliable serve the entire LIFE burnup cycle without failure.

42 ENGINEERING↗

Quantitative evaluation of an air-monitoring network using atmospheric transport modeling and frequency of detection methods

A methodology to quantify the performance of an air monitoring network in terms of frequency of detection has been developed. The methodology utilizes an atmospheric transport model to predict air concentrations of radionuclides at the samplers for a given release time and duration. Frequency of detection is defined as the fraction of “events” that result in a detection at either a single sampler or network of samplers. An “event” is defined as a release of finite duration that begins on a given day and hour of the year from a facility with the potential to emit airborne radionuclides. Another metric of interest is the network intensity, which is defined as the fraction of samplers in the network that have a positive detection for a given event. The frequency of detection methodology allows for evaluation of short-term releases that include effects of short-term variability in meteorological conditions. The methodology was tested using the U.S. Department of Energy Idaho National Laboratory (INL) Site ambient air monitoring network consisting of 37 low-volume air samplers in 31 different locations covering a 17,630 km 2 region. Releases from six major INL facilities distributed over an area of 1,435 km 2 were modeled and included three stack sources and eight ground-level sources. A Lagrangian Puff air dispersion model (CALPUFF) was used to model atmospheric transport. The model was validated using historical 125 Sb releases and measurements. Relevant one-week release quantities from each emission source were calculated based on a dose of 1.9 × 10 –4 mSv at a public receptor (0.01 mSv assuming release persists over a year). Important radionuclides considered include 241 Am, 137 Cs, 238 Pu, 239 Pu, 90 Sr, and tritium. Results show the detection frequency is over 97.5% for the entire network considering all sources and radionuclides. Network intensities ranged from 3.75% to 62.7%. Evaluation of individual samplers indicated some samplers were poorly situated and add little to the overall effectiveness of the network. As a result, using the frequency of detection methods, optimum sampler placements were simulated that could substantially improve the performance and efficiency of the network.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Computational Evaluation of Neutron Multiplicity Measurements of Polyethylene-Reflected Plutonium Metal

Simulations of neutron multiplicity measurements of a highly multiplicative plutonium sphere measured with a moderated array of 3 He proportional counters have consistently overpredicted the mean and variance of the measured multiplicity distribution. In contrast, identical experiments using a 252 Cf source have been accurately simulated. This paper outlines a sensitivity analysis of several key parameters that could account for the overprediction in the simulation of the plutonium sphere. Parameters that were analyzed include source-detector distance, detector dead time, variations in density and volume of the plutonium, and the value of v for 239 Pu-induced fission. Of these parameters, the only factor that accounted for the overprediction within reasonable bounds was a change in the value of the 239 Pu $\bar{v}$ . The sensitivity analysis showed that a small change (1.14% reduction) in the value of $\bar{v}$ dramatically improved the simulated results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Distinguishing Plutonium Metal from Plutonium Oxide Using Fast Neutrons, Preliminary Experimental Results

This report is the experimental counterpart of a paper in which algorithms were developed (a) to distinguish chemical forms of plutonium, and (b) to extract the multiplication of a plutonium measurement using liquid scintillators for fast neutron measurements. While we had tested our algorithms using Monte Carlo simulations in Ref. [1], we now propose to apply the same algorithms to experimental measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BISON Contact Algorithm Improvements in Support of Pellet Cladding Mechanical Interaction Modeling

The thermal and mechanical behavior of the gap between the fuel and cladding plays an extremely important role in determining the response of light water reactor (LWR) fuel under irradiation. This is especially true during situations when pellet-cladding mechanical interactions (PCMI) have a significant effect on the behavior of the fuel/cladding system. The BISON code, which is being used as the fuel performance simulation tool for the CASL program, employs contact detection and enforcement algorithms to realistically simulate the thermal and mechanical interactions across the fuel/cladding interaction in LWR fuel. These contact algorithms permit accurate representation of these interactions even when there is significant relative movement between the two surfaces, which is typically the case in many regions of an LWR fuel rod. This report summarizes work done during the 2017 fiscal year to further improve the accuracy and robustness of the contact enforcement algorithms in BISON. This work will benefit all BISON simulations, but will particularly benefit simulations scenarios where PCMI is of interest.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Design Study of the Parallel-Slit Ring Collimator for Fast Neutron Emission Tomography of Spent Fuel

For the past 18 months, Oak Ridge National Laboratory has been developing a passive fast-neutron emission tomography capability. The goal of this development is a new passive capability to detect diversion of single fuel pins (rods) from spent or used nuclear fuel assemblies by performing neutron emission tomography. At present, a laboratory prototype imager is under construction. The purpose of the prototype imager is to demonstrate imaging capability sufficient to resolve individual fuel pins in a spent nuclear fuel assembly. This report documents the results of simulation studies to optimize the design of the prototype imager.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigation of Luminescent Ceria as a Plutonium Oxide Simulant. Final Report

Plutonium oxide powders from various production lines at Los Alamos National Laboratory are stored and transported in specially designed “SAVY-4000”, “Hagan”, or other containment systems. Cerium oxide powder has been used as a less-hazardous simulant powder for testing accidental release from these containers under various operational scenarios. This work investigates the development and use of fluorescent cerium oxide powders as a more easily detectable, and potentially quantifiable, simulant powder for plutonium oxide container systems

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of molecular dynamics potential for uranium silicide fuels

Use of uranium–silicide (U-Si) in place of uranium dioxide (UO2) is one of the promising concepts being proposed to increase the accident tolerance of nuclear fuels. This is due to a higher thermal conductivity than UO2 that results in lower centerline temperatures. U-Si also has a higher fissile density, which may enable some new cladding concepts that would otherwise require increased enrichment limits to compensate for their neutronic penalty. However, many critical material properties for U-Si have not been determined experimentally. For example, silicide compounds (U3Si2 and U3Si) are known to become amorphous under irradiation. There was clear independent experimental evidence to support a crystalline to amorphous transformation in those compounds. However, it is still not well understood how the amorphous transformation will affect on fuel behavior. It is anticipated that modeling and simulation may deliver guidance on the importance of various properties and help prioritize experimental work. In order to develop knowledge-based models for use at the engineering scale with a minimum of empirical parameters and increase the predictive capabilities of the developed model, inputs from atomistic simulations are essential. First-principles based density functional theory (DFT) calculations will provide the most reliable information. However, it is probably not possible to obtain kinetic information such as amorphization under irradiation directly from DFT simulations due to size and time limitations. Thus, a more feasible way may be to employ molecular dynamics (MD) simulation. Unfortunately, so far no MD potential is available for U-Si to discover the underlying mechanisms. Here, we will present our recent progress in developing a U-Si potential from ab initio data. This work is supported by the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program funded by the U.S. Department of Energy, Office of Nuclear Energy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Test Plan Proposal for an International Joint Project for Transient Testing of Fast Reactor Fuels

EXECUTIVE SUMMARY An international joint project for transient testing of fast reactor fuels is proposed. Input from several countries is provided regarding their advanced/fast reactor programs, and the objectives and methods are given based on both historical projects and modern tools and methods. The full package would include irradiation testing using TREAT, use of existing facilities for non destructive exams/evaluations (NDE) and post irradiation exams (PIE), and integration of current state-of-the-art modeling and simulation (M&S) tools to aid in both experiment design, and prediction of experimental results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Swelling and Fission Gas Release of U-10Mo and U-17Mo Following Neutron Irradiation at 250 – 500°C

The performance of metallic fuel alloys, U-10Mo and U-17Mo, was examined using the MiniFuel test system in the High Flux Isotope Reactor. Approximately 0.8 mm thick disks were irradiated at target temperatures of 250°C, 350°C, 450°C, and 500°C up to three different fission densities, culminating at a maximum fission density of 6.8 × 10 20 cm −3 . Fission rates decayed from 3 – 6 × 10 13 cm −3 s −1 to 2 – 4 × 10 13 cm −3 s −1 over the course of the longest, eight cycle, irradiation as the 235 U was consumed and the 239 Pu concentration accumulated. Actual irradiation temperature on the last day of irradiation was measured via dilatometry using the SiC passive thermometry recovered from the MiniFuel subcapsules and compared favorably with the thermal calculations using as-built geometry and test conditions. Furthermore, average simulated temperatures were within 50°C of the target temperatures, except for the 500°C irradiation, for which the temperature variation was 62°C, 32°C, and 90°C in the in two, four, and eight cycle irradiations, respectively. Fission gas release (FGR) measurements showed no release above recoil for any U-17Mo fuels or for the U-10Mo fuel irradiated at 250°C. Finally, significant (40%–80%) FGR was found for the medium- to highest-burnup U-10Mo samples irradiated at target temperatures 350°C–500°C. Significant FGR correlated with sample thickness swelling, which was as high as 13%–35% for high-release samples and below 7% for all other (low–gas release) samples.

FGR↗

Simulated Verification of Fuel Element Inventory in a Small Reactor Core Using the Nuclear Materials Identification System (NMIS)

The International Panel on Climate Change projects that by 2050 the world energy demand may double. Although the primary focus for new nuclear power plants in industrialized nations is on large plants in the 1000-1600 MWe range, there is an increasing demand for small and medium reactors (SMRs). About half of the innovative SMR concepts are for small (<300 MWe) reactors with a 5–30-year life without on-site refueling. This type of reactor is also known as a battery-type reactor. These reactors are particularly attractive to countries with small power grids and for non-electrical purposes such as heating, hydrogen production, and seawater desalination. Traditionally, this type of reactor has been used in a nautical propulsion role. This type of reactor is designed as a permanently sealed unit to prevent the diversion of the uranium in the core by the user. However, after initial fabrication it will be necessary to verify that the newly fabricated reactor core contains the quantity of uranium that initially entered the fuel fabrication plant. In most instances, traditional inspection techniques can be used to perform this verification, but in certain situations the core design will be considered sensitive. Non-intrusive verification techniques must be utilized in these situations. The Nuclear Materials Identification System (NMIS) with imaging uses active interrogation and a fast time correlation processor to characterize fissile material. The MCNP-PoliMi computer code was used to simulate NMIS measurements of a small, sealed reactor core. Because most battery-type reactor designs are still in the early design phase, a more traditional design based on a Russian icebreaker core was used in the simulations. These simulations show how the radiography capabilities of the NMIS could be used to detect the diversion of fissile material by detecting void areas in the assembled core where fuel elements have been removed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗