Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

General Correlations for Laminar Flow Friction Loss and Heat Transfer in Plain Rectangular Plate-Fin Cores

In this paper, new generalized correlations for predicting the average fanning friction factor f and average Nusselt number Nu for laminar flow in plain plate-fin compact cores of rectangular cross section are presented. These are based on extended experimental data, as well as three-dimensional computational simulations, obtained for a broad range of fin density and geometrical attributes. The results indicate that while the fully developed forced convection scales only with the interfin channel cross-sectional ratio α (fin spacing by fin height), the entrance region hydrodynamic and thermal performance is additionally a function of the fin-core length L, flow Reynolds number Re, and fluid Prandtl number Pr. The developing flow and convection is further shown to scale as: (fRe)~(L/d h Re) 1/2 , and Nu ~(L/d h Re) 1/2 Pr 1/3 Φ(α), where f, Re, and Nu are all based on the hydraulic diameter dh of the interfin flow channel. Generalized correlations for both (fRe) and Nu are developed by the corresponding scaling of the forced convection behavior and asymptotic matching of the entrance or developing flow (short fin-core flow length) and the fully developed flow (large fin-core flow length) region performance. Finally, the predictions from these correlations are found to be within ±15% of all available experimental data for air, water, and glycol (0.71 ≤ Pr ≤ 10), and fin cores with 0 < α ≤ 1.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure based modeling of friction stir welded joint of dissimilar metals using crystal plasticity

We report the friction stir welding (FSW) process shows promising results in joining dissimilar metals which are otherwise almost impossible to join using traditional welding techniques. Being a new technique, the deformation and the failure mechanism of the joints made by the FSW process needs to be investigated. In this work, a joint between AZ31 Mg alloy and DP590 steel is modeled using phenomenological crystal plasticity formulation on the mesoscale in the form of a representative volume element (RVE). The interface of the two materials is modeled using a cohesive zone model. A parametric study has been performed to understand the effect of grain size and interface fracture toughness as well as strength on the mechanical performance of the joint. It was found that the grain size of AZ31 Mg alloy, as well as DP590 steel, has little effect on the overall joint performance. On the other hand, interface fracture toughness and strength have a significant impact on the mechanical properties of the joint

36 MATERIALS SCIENCE↗
DOE OSTI2023

COUPLING SMOOTHED PARTICLE HYDRODYNAMICS WITH FINITE ELEMENT METHOD TO SIMULATE RESIDUAL STRESSES FROM FRICTION STIR PROCESSING

Friction stir processing (FSP) is a solid-state material processing technique that locally modifies the microstructure but also induces undesirable residual stresses. A robust numerical model for the FSP can help in mitigating these residual stresses. Heat source models within a finite element method (FEM) framework suffer from inaccuracies. In contrast, smoothed particle hydrodynamics (SPH) model that explicitly captures the material flow near the tool and the associated heat generation are accurate. However, the computational expense of SPH simulations can be prohibitive. In this work, we propose a coupled SPH-FEM framework. SPH is used to model the heat generation accurately near the tool and which is then inserted into to the FEM model as a heat source. To verify this proposed coupling approach, a test case is set up with typical FSP conditions and it is modeled in both SPH and SPH-FEM. The temperatures profiles were compared after the simulations have reached steady-state temperatures. The similarity of the temperature profiles from SPH-FEA and SPH validated the proposed coupling approach. This proposed approach achieves the accuracy of the SPH method while potentially retaining the low computational expense of FEM.

smoothed particle hydrodynamics, Finite Element Me↗
DOE OSTI2019

Formation of Microcracks in a Heterogeneous Solid (Sandstone) under the Influence of Friction

The growth rate and size of microcracks, formed in the surface layer of a heterogeneous natural solid (sandstone) under friction were studied via triboluminescence. It was discovered that destruction of the crystal lattice of plagioclase and quartz, composing sandstones, induces triboluminescence signals. Each s-ignal corresponds to a microcrack, whose surface contains electronically excited free radicals ≡Si–O{sup –} and Fe{sup 3+} ions. The size and growth rate of microcracks were assessed by means of analysis of the rate and duration of the buildup of these signals. The growth rate of microcracks turned out to be less than the elastic wave velocity (~700 m/s) and varied from ∼380 to ∼650 m/s. The size of microcracks varied from ∼4 to ∼7 μm. It was assumed that the variation in the size and growth rate of microcracks were caused by differences in value of the barriers, upon breaking which the microcracks appear.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Effect of tool pin features on process response variables during friction stir welding of dissimilar aluminum alloys

In this article, the effect of pin features and orientation/placement of the materials on advancing side were investigated for friction stir welding (FSW) of dissimilar aluminum alloys AA2050 and AA6061. Pins for FSW were produced with a 2.12 mm pitch thread having three flats/flutes. Three sets of rotational speed/welding speed were used to perform a series of welds in a butt joint arrangement. The results show that, joint quality, process response variables and welding temperature are highly affected by pin features and material orientation in FSW. Defect free joints with effective material transportation in the weld nugget zone were obtained when welding was performed with AA2050 on the advancing side. The tool also encounters less in-plane reaction force for welding with 2050 on the advancing side. Pin with thread+3 flats produces quality welds at low rotational and travel speed regardless of the location of alloys on advancing or retreating side.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Utah FORGE Core Material Friction Experiments

The following folders contain 3 friction experiments on Utah FORGE core material from depths of 6735 - 8533ft. The experiment conditions range from 100% relative humidity at room temperature to fluid-saturated at 110C. Experiments were done on both intact samples in a single-direct shear configuration, double-direct shear, and gouge.

15 GEOTHERMAL ENERGY↗
DOE OSTI2018

Friction Stir Scribe Joining of Carbon Fiber Reinforced Polymer (CFRP) to Aluminum

The purpose of this project was to develop the critical process technology, models, and tools necessary to advance the Friction Stir Scribe, FSS, joining method through experimentation, validation at the laboratory scale, and integration into a production-like robotic environment. Implementation of FSS technology for joining polymer composites to metals will enable greater use of lightweight materials by providing technology capable of joining linear configurations without the use of adhesives or other third-body fasteners by creating an in-situ joint from the parent materials. As FSS technology provides the capability to join multi-material structures on robotic platforms using linear configurations, the development of this technology for use on the BIW will impact a great diversity of CFRP joints within the vehicle; thus, allowing a greater reduction in vehicle mass through more specifically designed structures. The FSS process has been developed to include integration of the FSS tool with a stationary shoulder, which has been shown to be required to achieve the desired surface quality (i.e., crown flash level). However, the targeted joint strength has not been achieved because the resulting stirred CFRP microstructure does not provide similar performance as the as-molded composite leading to low fracture strengths despite our efforts investigating various unique alternative approaches. In support of the experimental work, a process-structure model was developed and validated for the FSS joining (FSSJ) process using surrogate materials (steel and Al). The cyclic corrosion testing of the FSS joints and self-piercing riveted (SPR) joints revealed different modes of galvanic corrosion in the two types of joints. The SPR samples exhibited a greater amount of corrosion on the external surfaces. The presence of steel rivets in these joints exacerbated the situation, with the rivets getting preferentially corroded. The FSSJ samples despite exhibiting less surface corrosion, exhibited severe corrosion under the joint overlap area.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rotary Inertia Friction Welding of Dissimilar High-Strength 422 Martensitic Stainless Steel and 4140 Low Alloy Steel for Heavy-Duty Engine Piston Fabrication

AISI 422 martensitic stainless steel with superior high temperature performance (oxidation resistance and strength) is under evaluation for replacing current heavy-duty piston crown materials, AISI 4140 martensitic steel and micro alloyed steel (MAS) 38MnSiVS5, to fabricate a multimaterial piston. This multimaterial piston concept further improved power density and fuel economy by allowing heavyduty diesel engines to operate at higher temperatures and pressures. Joining AISI 422 steel piston crowns with AISI 4140 steel piston skirts is a key manufacturing step for this multimaterial piston. However, the significant differences in strength, elevated temperature flow stress, alloy chemistry, and temper resistance between these two martensitic steels cause some weldability issues (cracking) and metallurgical challenges (alloying element migration/segregation) when using conventional fusion-based welding processes. Rotary inertia friction welding (RIFW), a solid-state welding process, has been the preferred method to join 4140 crowns to 4140 skirts (and MAS crowns to MAS skirts) in high-volume production of current heavy-duty diesel engine pistons. It has been used to join these two materials with relatively comparable alloy chemistry to fabricate pistons with MAS skirts and 4140 crowns. Meanwhile, RIFW has also been a preferred method of dissimilar metal welding. However, RIFW of dissimilar high-strength martensitic steels has yet to be widely pursued. The interfacial microstructure complexities created by the thermomechanical process and highly nonequilibrium phase transformations during RIFW are a significant challenge for understanding and predicting their joining behavior and have not been reported in detail. Here, in this work, defect-free AISI 422 steel-AISI 4140 multimaterial pistons were successfully fabricated using the RIFW process. The interfacial microstructure and mechanical properties of dissimilar 422/4140 steel RIFW in the as-welded condition were experimentally studied in detail. The results provide critical baseline information for understanding RIFW mechanisms and guiding subsequent postweld heat treatment (PWHT) practice.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Laser modification of frictional surfaces

Improvement in the physicomechanical properties and frictional characteristics of cylinder and piston surfaces in airplane internal-combustion engines is considered. A method of developing recommendations regarding the optimization of laser treatment is proposed on the basis of experiments and a model of surface wear.

42 ENGINEERING↗
DOE OSTI2019

Dynamics of a Cylinder with a Displaced Center of Gravity on a Vibrating Base with Dry Friction

Forced vibrations of a cylinder with a displaced center of gravity on a rigid base vibrating horizontally (perpendicular to the generatrix of the cylindrical surface) are investigated. At the contact point between the cylindrical surface and the base, dry friction is assumed. The problem is solved by the Bubnov–Galerkin method. The results are expressed as amplitude–frequency characteristics.

42 ENGINEERING↗
DOE OSTI2023

Microstructural, Corrosion, and Mechanical Characterization of Friction Stir Welded Al 6022-to-ZEK100 Mg Joints

Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone’s corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Crack-Free Joining of High-Strength AA7055 Sheets by Friction Based Self-Piercing Riveting with the Aid of Numerical Design

Unique friction-based self-piercing riveting (F-SPR) was employed to join high-strength, low-ductility aluminum alloy 7055 for lightweight vehicle applications. This study aimed to maximize the joint strength of the AA7055 F-SPR joint while avoiding cracking issues due to low ductility at room temperature. A fully coupled Eulerian–Lagrangian (CEL) model was employed to predict the process temperature during F-SPR, and the temperature field was then mapped onto a 2D axisymmetric equivalent model for accelerated numerical analysis. The geometry, dimensions, and material strength of the rivet, as well as the depth of the die cavity and plunging depth, were investigated to enhance joint formation. Also, a static finite-element analysis model was developed to predict and analyze the stress distribution in the rivet under different mechanical testing loading conditions. Overall, the numerical model showed good agreement with the experiment results, such as joint formation and mechanical joint strength. With the aid of virtual fabrication through numerical modeling, the joint design iterations and process development time of F-SPR were greatly reduced regarding the goal of lightweight, high-strength aluminum joining.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Study of Helium Irradiation Effect on Al6061 Alloy Fabricated by Additive Friction Stir Deposition

Additive friction stir deposition (AFS-D) is considered a productive method of additive manufacturing (AM) due to its ability to produce dense mechanical parts at a faster deposition rate compared to other AM methods. Al6061 alloy finds extensive application in aerospace and nuclear engineering; nevertheless, exposure to radiation or high-energy particles over time tends to deteriorate their mechanical performance. However, the effect of radiation on the components manufactured using the AFS-D method is still unexamined. In this work, samples from the as-fabricated Al6061 alloy, by AFS-D, and the Al6061 feedstock rod were irradiated with He+ ions to 10 dpa at ambient temperature. The microstructural and mechanical changes induced by irradiation of He+ were examined using a scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and nanoindentation. This study demonstrates that, at 10 dpa of irradiation damage, the feedstock Al6061 produced a bigger size of He bubbles than the AFS-D Al6061. Nanoindentation analysis revealed that both the feedstock Al6061 and AFS-D Al6061 samples have experienced radiation-induced hardening. These studies provide a valuable understanding of the microstructural and mechanical performance of AFS-D materials in radiation environments, offering essential data for the selection of materials and processing methods for potential application in aerospace and nuclear engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2016

The influence of quantum vacuum friction on pulsars

We first revisit the energy loss mechanism known as quantum vacuum friction (QVF), clarifying some of its subtleties. Then we investigate the observables that could easily differentiate QVF from the classical magnetic dipole radiation for pulsars with accurately measured braking indices (n). We show that this is particularly the case for the time evolution of a pulsar’s magnetic dipole direction ( ϕ-dot ) and surface magnetic field ( B-dot {sub 0}). As is well known in the context of the classic magnetic dipole radiation, n < 3 would only be possible for positive ( B-dot {sub 0}/B{sub 0}+ ϕ-dot /tanϕ), which, for instance, leads to B-dot {sub 0}>0 ( ϕ-dot >0) when ϕ (B {sub 0}) is constant. On the other hand, we show that QVF can result in very different predictions with respect to those above. Finally, even if B-dot {sub 0} has the same sign in both of the aforementioned models for a pulsar, then, for a given ϕ, we show that they give rise to different associated timescales, which could be another way to falsify QVF.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Structure, Kinematics, and Observability of the Large Magellanic Cloud’s Dynamical Friction Wake in Cold versus Fuzzy Dark Matter

Abstract The Large Magellanic Cloud (LMC) will induce a dynamical friction (DF) wake on infall to the Milky Way (MW). The MW’s stellar halo will respond to the gravity of the LMC and the dark matter (DM) wake, forming a stellar counterpart to the DM wake. This provides a novel opportunity to constrain the properties of the DM particle. We present a suite of high-resolution, windtunnel-style simulations of the LMC's DF wake that compare the structure, kinematics, and stellar tracer response of the DM wake in cold DM (CDM), with and without self-gravity, versus fuzzy DM (FDM) with m a = 10 −23 eV. We conclude that the self-gravity of the DM wake cannot be ignored. Its inclusion raises the wake’s density by ∼10%, and holds the wake together over larger distances (∼50 kpc) than if self-gravity is ignored. The DM wake’s mass is comparable to the LMC’s infall mass, meaning the DM wake is a significant perturber to the dynamics of MW halo tracers. An FDM wake is more granular in structure and is ∼20% dynamically colder than a CDM wake, but with comparable density. The granularity of an FDM wake increases the stars’ kinematic response at the percent level compared to CDM, providing a possible avenue of distinguishing a CDM versus FDM wake. This underscores the need for kinematic measurements of stars in the stellar halo at distances of 70–100 kpc.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2014

Friction Stir Welding of Line-Pipe Steels

Friction stir welding (FSW) offers both economic and technical advantages over conventional fusion welding practices for welding line-pipe. For offshore line-pipe construction, the economic savings has been shown to be considerable, approaching a calculated 25%. Offshore pipe is relatively small diameter but heavy wall compared to onshore pipe. One concern is the ability to achieve consistent full weld penetration in an on-site offshore FSW operation, e.g., on a lay-barge. In addition, depending on the size and morphology of the unwelded zone, lack of penetration at the weld root can be difficult if not impossible to detect by conventional NDE methods. Thus, an approach to assure consistent full penetration via process control is required for offshore line-pipe construction using FSW. For offshore construction, an internal structural mandrel can be used offering the opportunity to use a sacrificial anvil FSW approach. With this approach, a small volume of sacrificial material can be inserted into the structural anvil. The FSW tool penetrates into the sacrificial anvil, beyond the inner diameter of the pipe wall, thus assuring full penetration. The sacrificial material is subsequently removed from the pipe inner wall. In the work presented herein, FSW studies were completed on both 6 mm and 12 mm wall thickness line-pipe. Lastly, post-FSW evaluations including radiography, root-bend tests, and metallography demonstrated the merits of the sacrificial anvil approach to achieve consistent full penetration.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗