SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Particle-based models of crosslinked PDMS were developed at multiple resolutions for direct numerical simulations of silicone rheological properties and behavior.
Computational predictions of vaporization properties aid the de novo design of green chemicals, including clean alternative fuels, working fluids for efficient thermal energy recovery, and polymers that are easily degradable and recyclable.
Transient, near-field mixing of a supercritical fluid injected into supercritical and subcritical environments is investigated experimentally. Fuel (propane) from a 100 μm diameter Bosch diesel injector is injected into a high-pressure test rig with a steady flow of heated, low-velocity nitrogen to control the ambient pressure and temperature. The fuel supply pressure is approximately 190 bar, allowing short injections lasting 3–4 ms to be performed in quick succession to acquire statistically significant datasets to represent the unsteady fuel–air mixing. Two test cases with the same ambient density and injector inlet pressure and temperature were chosen in an attempt to isolate effects of mixture phase behavior. Microscopic rainbow Schlieren deflectometry (RSD) is used for visualization and quantitative data acquisition. In the case of the supercritical ambient, the injector inlet and exit and ambient conditions are all supercritical. The RSD analysis reveals a mixing process similar to the single phase fluid mixing, though condensation is also observed locally, and can be explained by the adiabatic mixing theory presented in the paper. For the subcritical ambient case, the injector inlet is supercritical, but the injector exit and ambient conditions are both subcritical. The results show a rapid expansion in the near-field promoting mixing between propane and nitrogen. At downstream locations, significant condensation is also observed as predicted by the adiabatic mixing theory. As a result, the supercritical ambient case exhibited longer and narrower jet penetration compared to the subcritical ambient case.
Using a uniquely configured glow discharge-based Shivalik Plasma Device-I, we demonstrate a variety of collective phenomena in dusty plasma away from the glow discharge region. The cylindrical glass device produces plasma using parallel disc-shaped electrodes with a smaller anode size than the cathode. The dust microparticles are initially sprinkled over the grounded cathode. These particles acquire a significant negative charge upon plasma formation, resulting in their levitation due to the balance between the Coulomb force and gravity. The new device supports the levitation of a big-sized (10 × 8 × 5 cm 3 ) three-dimensional dust cloud over the glass surface. It contrasts the dusty plasma formations in-between electrodes reported earlier. As the discharge voltage varies from high to low, the dust cloud travels from over the glass surface to between the electrodes. A complex interplay of dust void over the cathode, a sharp density gradient, and gravity lead to self-excitation of collective dust phenomena. It includes dust density waves (phase velocity, v ph ~4 cm/s), dust cloud oscillation (frequency, f = 5 Hz), sheared flow (flow velocity, v f ~ 1 cm/s), and multiple-sized dust vortices. These dust vortices provided an excellent platform for studying turbulent mixing phenomena. The power spectrum analysis agreed with two-dimensional Kolmogorov power-law scaling. This is an ideal dusty plasma apparatus where we can create or move the dust cloud to a location of choice from the glass surface to in-between the electrodes and excite one among many collective dust dynamics.
Diamond anvil cells are the most popular means of generating pressures above 2 GPa. However, in many experiments, such as nuclear magnetic resonance and x-ray absorption, the metallic pressurizing gasket (which confines much of the sample) represents an occluding barrier that requires a low Z gasket material (e.g., Be), a split gasket, or other means to enable better coupling of the sample to electromagnetic radiation. In this paper, we demonstrate a novel method for generating high pressures that confines the sample just above the plane of the gasket by using a diamond with a laser hole drilled into the center of the tip. The sample is then confined by the hole, which is sealed by a flat gasket that fits over the hole. When load is applied to the diamonds, metal flows from the deformed gasket into the hole thereby pressurizing the sample similarly to how a piston pressurizes gas inside a cylinder. The pressurized sample is above the metallic gasket plane just inside the tip of the diamond, and thus easily accessible via x rays or visible light that skims just above the plane of the gasket providing an enhanced aperture of radiation collection. Furthermore, we have demonstrated the utility of this method by obtaining Raman spectra of SnC 2 O 4 and x-ray diffraction spectra of seleno-DL-cystine, all at high pressures.
Anomalous transport of mixed deuterium–tritium plasma in the edge of magnetic fusion reactors is investigated using numerical solutions of resistive drift wave turbulence model equations, including finite Larmor radius effects, that are derived within the generalized Hasegawa–Wakatani framework. The anomalous cross field diffusivities of deuterium and tritium are compared in turbulence regimes with different values of the electron adiabaticity parameter controlling the existence of zonal flow. The dependence of the tritium-to-deuterium diffusivity ratio on the deuterium and tritium densities and the logarithmic density gradients is analyzed, and a scaling relation is obtained.
We report the first fully kinetic, quantum study of kinetic electrostatic electron nonlinear (KEEN) waves, showing that quantum diffraction systematically erodes the classical trapping mechanism, narrows harmonic locking to the fundamental, and hastens post-drive decay. Electrons are evolved with a second-order Strang-split 1D1V Wigner–Poisson solver that couples conservative semi-Lagrangian WENO advection to an analytic Fourier space update for the non-local Wigner term, while ions remain classical. We focus on collisionless dynamics in a weakly coupled regime, providing a controlled baseline before collisional extensions. Short, frequency-tuned ponderomotive pulses drive KEEN formation in a uniform Maxwellian plasma; as the dimensionless quantum parameter H rises from the classical limit to values relevant to warm-dense matter, doped semiconductors, and 2D electron systems, the drive threshold increases, higher harmonics are damped, trapped electron vortices diffuse, and the subplasma electrostatic energy relaxes to a lower stationary level, as confirmed by continuous wavelet analysis. These microscopic changes carry macroscopic weight. Ignition-scale capsules now compress matter to regimes where the electron de Broglie wavelength rivals the Debye length, making classical kinetic descriptions insufficient. By extending KEEN physics into this quantum domain, our results offer a potential diagnostic of non-equilibrium electron dynamics for next-generation inertial-confinement designs and high-energy-density platforms, indicating that predictive fusion modeling may benefit from the integration of kinetic fidelity with quantum effects.
Complex fluids near interfaces or confined within nanoscale volumes can exhibit substantial shifts in physical properties compared to bulk, including glass transition temperature, phase separation, and crystallization. Because studies of these effects typically use thin film samples with one dimension of confinement, it is generally unclear how more extreme spatial confinement may influence these properties. In this work, we used x-ray photon correlation spectroscopy and gold nanoprobes to characterize polyethylene oxide confined by nanostructured gratings (<100nm width) and measured the viscosity in this nanoconfinement regime to be ~500 times the bulk viscosity. Here, this enhanced viscosity occurs even when the scale of confinement is several times the polymer's radius of gyration, consistent with previous reports of polymer viscosity near flat interfaces.
Despite being a quantum two-fluid system, superfluid helium-4 (He II) is observed to behave similarly to classical fluids when a flow is generated by mechanical forcing. This similarity has brought up the feasibility of utilizing He II for high Reynolds number classical turbulence research, considering the small kinematic viscosity of He II. However, it has been suggested that the nonclassical dissipation mechanism in He II at small scales may alter its turbulent statistics and intermittency. In this work, we report our study of a nearly homogeneous and isotropic turbulence (HIT) generated by a towed grid in He II. We measure the velocity field using particle tracking velocimetry with solidified deuterium particles as the tracers. By correlating the velocities measured simultaneously on different particle trajectories or at different times along the same particle trajectory, we are able to conduct both Eulerian and Lagrangian flow analyses. Spatial velocity structure functions obtained through the Eulerian analysis show scaling behaviors in the inertial subrange similar to that for classical HIT but with enhanced intermittency. The Lagrangian analysis allows us to examine the flow statistics down to below the dissipation length scale. Interestingly, abnormal deviations from the classical scaling behaviors are observed in this regime. Lastly, we discuss how these deviations may relate to the motion of quantized vortices in the superfluid component in He II.
Molten salts are complex fluids that incorporate multi-phase behavior depending on the chemistry and the physical properties of the entrained components. These components include the carrier salt, the actinide fuel, and fission, activation, and corrosion products, the concentrations of which depends on the burnup history of the salt. Radionuclide transport from the salt into the cover gas / off-gas system depends on volatility as predicted by thermochemistry, but data from the Molten Salt Reactor Experiment (MSRE) conducted in the late 1960s suggest that bubble formation and transport are also important. Anomalously high fractions of noble metals were found in the off-gas system and were attributed to transportation with parent salt aerosols and their association with rising noble gas bubbles. The prediction of such phenomena requires coupled neutronic, thermal hydraulic, and chemical equilibrium calculations, the framework of which is being developed within the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program supported by the US Department of Energy (DOE) Office of Nuclear Energy (NE). However, separate effects tests and models of experiments using tools such as SAM and Thermochimica can guide model developers through important processes. Conversely, model development guides the choice of experiments and systems to provide data that are relevant for validation. This report describes several experiments that tracked gas transport in molten salts, ranging from small-scale systems to large-scale loops. Gas transportation in a molten salt, LiCl-KCl, has been studied using the shadowgraph technique. Sensors such as residual gas analysis, Raman spectroscopy, and laser-induced breakdown spectroscopy have been tested for off-gas measurements. These data were used to interpret how the gases move through the upstream salt / cover gas and the interface between them. Differential pressure measurements were able to detect individual gas bubbles as they popped at the liquid–gas interface. Salt aerosols were collected on a cascade impactor. Their formation was also observed directly via the shadowgraph method, and most of these aerosols were launched ballistically into the cover gas. Fine mists could also be observed. Convection currents through the salt were visualized and can be used to calculate the thermophysical properties of the salt itself. The apparatuses described in this report and in a previous work (McFarlane et al. 2023) have been commissioned and are available for use in making further measurements of salt/surrogate fission product behavior. Novel approaches using neutron imaging are planned for the study of fluoride salts, which cannot be contained in quartz, so shadowgraph visualization is not available. Bubble transport in convective flow and in a slow-moving salt column are planned. The mobile laser-induced breakdown spectroscopy (LIBS) system is available for several applications, including iodine capture in a molten hydroxide scrubber, H2 transport though molten salts to complement Raman analysis, and online tracking of salt aerosol generation, transport, and deposition. This report summarizes the findings from FY24 and the plans for FY25. The work completes milestone M2AT-24OR0702013 of the DOE-NE Advanced Reactor Technology, Molten Salt Reactor Campaign, DOE-NE-5.
The contact angle is a critical factor for determining the effective mass transfer area for carbon dioxide (CO 2 ) capture via the chemical absorption process in a packed column, and thus the overall capture efficiency of the packed column. Many widely used commercial packings involve microscale features (perforation, corrugation, etc.) that may also affect the wetting behavior. This study proposes a systematic method of using a modified Wilhelmy plate to measure the effective contact angle to characterize the solvent and featured packing interaction. In lieu of computational efforts relying on assumptions guided by semi-informed correlation, the proposed method directly measures the effective contact angle as a function of the solvent and packing thermophysical and hydrodynamic properties. The characterization of the effective contact angle is then integrated in the computational fluid dynamics modeling to reduce uncertainty in the prediction of effective mas transfer area. Experiments were conducted for stainless steel coupons using water and aqueous sodium hydroxide (NaOH) solvent for verification of the proposed experimental protocol. The surface tension of the aqueous NaOH solvent was altered using surfactant and antifoam. The effective contact angle increases with the increased value of the surface tension for flat stainless steel sheets. On the other hand, effective contact angles do not vary in Mellapak coupons for aqueous monoethanolamine (MEA) and NaOH solvent. In this case, surface textures and sheet design play a dominant role in the surface tension of solvents. Furthermore, CO 2 loading has a significant effect on the contact angle for Mellapak coupons. As expected, the contact angle decreases with the increasing temperature of CO 2 capture solvents (MEA, EEMPA). The effective contact angle measurement using the Wilhelmy plate method can provide more accurate and efficient solvents for characterizing the solvent-packing surface interactions. Subsequently, the present method enhances the accuracy of the prediction of the effective mass transfer area in carbon capture by solvent absorption.
Cyclic changes in concentration produced in fluid flowing through fixed bed of solid adsorbent, governing separation by beds wave propagation properties
Flashing injection involves expanding a fluid through an injector until a supersaturated state is reached, causing a portion of the fluid to flash to a vapor. This investigation considered the flow, atomization and spreading properties of flashing injectors with flowing liquids containing dissolved gases (Jet A/air) as well as superheated liquids (Freon-11). The use of a two-stage expansion process, separated by an expansion chamber, was found to be beneficial for good atomization properties of flashing injection - particularly for dissolved gas systems. Both locally homogeneous and separated flow models provided good predictions of injector flow properties. Conventional correlations for drop sizes from pressure and airblast injectors were successfully modified, using the separated flow model to prescribe injector exit conditions, and to correlate drop size measurements. Additional experimental results are provided for spray angles of sprays from flashing injectors.
Alternate processing methods have been investigated as a means of improving the mechanical properties of injection-molded SiC. Various mixing processes (dry, high-sheer, and fluid) were evaluated along with the morphology and particle size of the starting beta-SiC powder. Statistically-designed experiments were used to determine significant effects and interactions of variables in the mixing, injection molding, and binder removal process steps. Improvements in mechanical strength can be correlated with the reduction in flaw size observed in the injection molded green bodies obtained with improved processing methods.
An investigation was made of producing a workable model for the transient analysis of a cryogenic hydrogen filling system. A series of programs and subprograms defining the momentum, mass, and energy balances and the physical properties, transport properties, and their interactions were devised.The program was modified for a simple theoretical test fluid. Exhaustive runs and modifications were made and at this point no stability was achieved except in trivial cases.
One of the outstanding issues regarding the excitation of magnetosonic waves has been the observational evidence that obliquely propagating waves are dominant at comets and planetary foreshocks despite the predictions of linear theory that maximum growth occurs at parallel propagation. To address this issue, we have conducted a detailed linear theory using a beam-ring distribution function. The results have shown that such distribution functions are associated with four separate instabilities. Two of these instabilities are similar to the right hand resonant ion/ion and the non-resonant instabilities which are also present in the case of a field aligned beam. The other two instabilities are associated with the presence of ring part of the distribution function. One of these instabilities excites magnetosonic waves with maximum growth in the oblique directions. The other excites Alfven waves with maximum growth in the oblique directions. The importance of the former instability is that it may explain the oblique nature of the magnetosonic waves observed at planetary foreshocks and comets. In order to understand the nonlinear properties of these various instabilities, we have also conducted 2-D hybrid (particle ions, fluid electrons) simulations. We have found that when the beam density is sufficiently large so that the non-resonant instability has the largest growth rate, these waves dominate the initial wave power in the system. At later times, however, the obliquely propagating magnetosonic waves become dominant. Another important finding was that when the two instabilities which excite magnetosonic waves have the largest growth rates, the system is dominated by the obliquely propagating magnetosonic waves. This is despite the fact that the largest growth rate for one of the instabilities occurs in the parallel direction. The exact cause of this is not currently understood and is under investigation.
In a similar approach to that used for the previously issued correlation report for Coflon (CAPP/M.10), this report aims to identify any correlations between mechanical property changes and chemical/morphological changes for Tefzel, using information supplied in other MERL and TRI project reports. Differences identified with Coflon behaviour will be of scientific interest as well as appropriate to project applications, as Tefzel and Coflon are chemical isomers. Owing to the considerable chemical resistance of Tefzel, much of its testing so far has been based on mechanical properties. Where changes have occurred, chemical analysis can now be targeted more effectively. Relevant test data collated here include: tensile modulus and related properties, permeation coefficients, % crystallinity, some crack growth resistance measurements, and other observations where significant. Fluids based on methanol and amine (Fluid G), a mixture of methane, carbon dioxide and hydrogen sulphide gases plus an aqueous amine solution (Fluid F), and an aromatic oil mix of heptane, cyclohexane, toluene and 1-propanol (Fluid I) have affected Tefzel to varying degrees, and are discussed in some detail herein.
Instruments for the monitoring of hazardous gases in and near the space shuttle collect sample gas at pressures on the order of one atmosphere and analyze their properties in an ultra-high vacuum by means of a quadrupole-mass-spectrometer partial pressure transducer. Sampling systems for such devices normally produce the required pressure reduction through combinations of vacuum pumps, fluid Tees and flow restrictors (e.g. orifices, sintered metal frits or capillaries). The present work presents an analytical model of the fluid dynamics of such a pressure reduction system which enables the calculation of the pressure in the receiver vessal in terms of system parameters known from the specifications for a given system (e.g. rated pumping speeds of the pumping hardware and the diameters of two orifices situated in two branches of a fluid Tee). The resulting formulas will expedite the fine tuning of instruments now under development and the design of later generations of such devices.