Space shuttle aerothermodynamics - An overview
Space shuttle aerothermodynamics, discussing heat transfer measurements, phase change patterns, electron beam flow visualization and boundary layer transition
Henderson, A., Jr.↗
SEARCH · Engineering Papers
Results for “Flow Visualization”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An experimental investigation of trailing vortices behind a wing with a vortex dissipator
Trailing vortices behind wing tip with vortex dissipator, using wind tunnel flow visualization and flight tests
Chigier, N.↗
Detailed investigation of flowfields within large scale hypersonic inlet models
Analytical and experimental investigations were conducted to determine the characteristics of the internal flows in model passages representative of hypersonic inlets and also sufficiently large for meaningful data to be obtained. Three large-scale inlet models, each having a different compression ratio, were designed to provide high performance and approximately uniform static-pressure distributions at the throat stations. A wedge forebody was used to simulate the flowfield conditions at the entrance of the internal passages, thus removing the actual vehicle forebody from consideration in the design of the wind-tunnel models. Tests were conducted in a 3.5 foot hypersonic wind tunnel at a nominal test Mach number of 7.4 and freestream unit Reynolds number of 2,700,000 per foot. From flowfield survey data the inlet entrance, the entering inviscid and viscous flow conditions were determined prior to the analysis of the data obtained in the internal passages. Detailed flowfield survey data were obtained near the centerlines of the internal passages to define the boundary-layer development on the internal surfaces and the internal shock-wave configuration. Finally, flowfield data were measured across the throats of the inlet models to evaluate the internal performance of the internal passages. These data and additional results from surface instrumentation and flow visualization studies were utilized to determine the internal flowfield patterns and the inlet performance.
Seebaugh, W. R.↗
A method for increasing thrust reverser utilization on STOL aircraft.
A technique for increasing the utilization of thrust reversers on STOL aircraft is described. The technique involves asymmetric orientation of the reversed exhaust in such a manner as to avoid the problems of self-ingestion, even in the presence of a cross wind, and cross ingestion between adjacent engines. Experimental results of ingestion in a single nacelle inlet are discussed and flow visualization pictures are presented. An analytical model of ingestion is described and sample results are shown.
Tatom, J. W.↗
Investigation of the stability of the tip vortex generated by hovering propellers and rotors.
The objective of this experimental and theoretical investigation was to determine what factors and mechanisms are involved in vortex interaction and instability and how these phenomena manifest themselves. To answer these questions, the schlieren method of flow visualization was used to observe the wakes generated by two- and four-bladed model propellers and rotors. A concurrent free-wake analysis was conducted for comparative purposes. Schlieren pictures showing wake asymmetry, interaction, and instability are presented. Various factors and mechanisms believed to be responsible for these are discussed along with the effects produced by the number of blades, collective pitch, and tip speed. Free-wake calculations that qualitatively confirm those factors responsible for wake asymmetry and interaction are also presented.
Tangler, J. L.↗
Results of investigations on a 0.0405 scale model PRR version of the NR-SSV orbiter in the North American Aeronautical Laboratory low speed wind tunnel
Experimental aerodynamic investigations were conducted in a low speed wind tunnel on a scale model space shuttle vehicle (SSV) orbiter. The purpose of the test was to investigate the longitudinal and lateral-directional aerodynamic characteristics of the space shuttle orbiter. Emphasis was placed on model component, wing-glove, and wing-body fairing effects, as well as elevon, aileron, and rudder control effectiveness. Angles of attack from - 5 deg to + 30 deg and angles of sideslip of - 5 deg, 0 deg, and + 5 deg were tested. Static pressures were recorded on base, fuselage, and wing surfaces. Tufts and talc-kerosene flow visualization techniques were also utilized. The aerodynamic force balance results are presented in plotted and tabular form.
Kingsland, R. B.↗
Results of investigations on a 0.0405 scale model ATP version of the NR-SSV orbiter in the North American Aeronautical Laboratory low speed wind tunnel
Experimental aerodynamic investigations were conducted on a scale model space shuttle vehicle (SSV) orbiter. The purpose of the test was to investigate the longitudinal and lateral-directional aerodynamic characteristics. Emphasis was placed on model component, wing-glove, and wing-body fairing effects, as well as elevon, aileron, and rudder control effectiveness. Angles of attack from - 5 deg to + 30 deg and angles of sideslip from - 5 deg to + 10 deg were tested. Static pressures were recorded on base, fuselage, and wing surfaces. Tufts and talc-kerosene flow visualization techniques were also utilized. The aerodynamic force balance results are presented in plotted and tabular form.
Mennell, R.↗
Hypersonic aerodynamic characteristics of NR-ATP orbiter, orbiter with external tank, and ascent configuration
A scale model of the North American Rockwell ATP Orbiter with and without the external tank has been tested in a 22-inch helium tunnel at Mach 20 and a Reynolds number based on model length, of 2.14 times one million. Longitudinal and lateral-directional data were determined for the orbiter alone while only longitudinal characteristics and elevon roll effectiveness were investigated for the orbiter/tank combination. Oil flow and electron beam flow visualization studies were conducted for the orbiter alone, orbiter with external tank and the ascent configuration.
Ashby, G. C., Jr.↗
An experimental investigation of vortex stability, tip shapes, compressibility, and noise for hovering model rotors
Schlieren methods of flow visualization and hot-wire anemometry for velocity measurements were used to investigate the wakes generated by hovering model propellers and rotors. The research program was directed toward investigating (1) the stability of the tip vortex, (2) the effects produced by various tip shapes on performance and tip vortex characteristics, and (3) the shock formation and noise characteristics associated with various tip shapes. A free-wake analysis was also conducted for comparison with the vortex stability experimental results. Schlieren photographs showing wake asymmetry, interaction, and instability are presented along with a discussion of the effects produced by the number of blades, collective pitch, and tip speed. Two hot-wire anemometer techniques, used to measure the maximum circumferential velocity in the tip vortex, are discussed.
Tangler, J. L.↗
Aerodynamic characteristics of Lockheed delta-body orbiter and stage-and-one-half launch vehicle
An experimental wind tunnel test program was conducted to investigate the subsonic through high supersonic aerodynamic characteristics of the Lockheed delta lifting body orbiter and stage-and-one-half launch vehicle. Analyses and results of these data are presented. A 0.01-scale model of the LS 200-5 system was designed and fabricated for testing in wind tunnels. Orbiter and launch configurations were tested over a speed range of Mach 0.6 to 2.0, whereas only the orbiter was tested over a speed range of Mach 2.3 to 4.6. Six-component force and moment data, base pressures, and schlieren photos were obtained at various angles-of-attack and sideslip. A 0.03-scale model of the orbiter was also designed, fabricated, and tested in a wind tunnel. Six-component force and moment data, base pressure, and a limited amount of tuft flow visualization data were obtained on a variety of configuration combinations.
Velligan, F. A.↗
The effects of leading-edge serrations on reducing flow unsteadiness about airfoils.
High frequency surface pressure measurements were obtained from wind-tunnel tests over the Reynolds number range 1.2 x 1,000,000 to 6.2 x 1,000,000 on a rectangular wing of NACA 63-009 airfoil section. A wide selection of leading-edge serrations were also added to the basic airfoil. Under a two-dimensional laminar bubble very close to the leading edge of the basic airfoil there is a large peak in rms pressure, which is interpreted as an oscillation in size and position of the bubble. The serrations divide the bubble into segments and reduce the peak rms pressures. A low Reynolds number flow visualization test on a hydrofoil in water was also conducted. A von Karman vortex street was found trailing from the rear of the foil. Its frequency is at a much lower Strouhal number than in the high Reynolds number experiment, and is related mathematically to the airfoil trailing-edge and boundary-layer thicknesses.
Schwind, R. G.↗
Effects of spanwise rotation on the structure of two-dimensional fully developed turbulent channel flow.
Experiments on fully developed turbulent flow in a channel which is rotating at a steady rate about a spanwise axis are described. The Coriolis force components in the region of two-dimensional mean flow affect both local and global stability. Three stability-related phenomena were observed or inferred: (1) the reduction (increase) of the rate of wall-layer streak bursting in locally stabilized (destabilized) wall layers; (2) the total suppression of transition to turbulence in a stabilized layer; (3) the development of large-scale roll cells on the destabilized side of the channel by growth of a Taylor-Gortler vortex instability. Local effects of rotational stabilization, such as reduction of the turbulent stress in wall layers, can be related to the local Richardson number in a simple way. This paper not only investigates this effect, but also, by methods of flow visualization, exposes some of the underlying structure changes caused by rotation.-
Johnston, J. P.↗
The effects of leading-edge serrations on reducing flow unsteadiness about airfoils, an experimental and analytical investigation
High frequency surface pressure measurements were obtained from wind-tunnel tests over the Reynolds number range 1.2 times one million to 6.2 times one million on a rectangular wing of NACA 63-009 airfoil section. Measurements were also obtained with a wide selection of leading-edge serrations added to the basic airfoil. Under a two-dimensional laminar bubble very close to the leading edge of the basic airfoil there is a large apatial peak in rms pressure. Frequency analysis of the pressure signals in this region show a large, high-frequency energy peak which is interpreted as an oscillation in size and position of the bubble. The serrations divide the bubble into segments and reduce the peak rms pressures. A low Reynolds number flow visualization test on a hydrofoil in water was also conducted. A von Karman vortex street was found trailing from the rear of the foil. Its frequency is at a much lower Strouhal number than in the high Reynolds number experiment, and is related to the trailing-edge and boundary-layer thicknesses.
Schwind, R. G.↗
Effect of sweep angle on the pressure distributions and effectiveness of the ogee tip in diffusing a line vortex
Low-speed wind tunnel tests were conducted to study the influence of sweep angle on the pressure distributions of an ogee-tip configuration with relation to the effectiveness of the ogee tip in diffusing a line vortex. In addition to the pressure data, performance and flow-visualization data were obtained in the wind tunnel tests to evaluate the application of the ogee tip to aircraft configurations. The effect of sweep angle on the performance characteristics of a conventional-tip model, having equivalent planform area, was also investigated for comparison with the ogee-tip configuration. Results of the investigation generally indicate that sweep angle has little effect on the characteristics of the ogee in diffusing a line vortex.
Balcerak, J. C.↗
Effect of reaction control system jet-flow field interactions on a 0.015 scale model space shuttle orbiter aerodynamic characteristics
The effects of the reaction control system (RCS) jet-flow field interactions on the space shuttle orbiter system during entry are discussed. The primary objective of the test program was to obtain data for the shuttle orbiter configuration to determine control amplification factors resulting from jet interaction between the RCS plumes and the external flow over the vehicle. A secondary objective was to provide data for comparison and improvement of analytic jet interaction prediction techniques. The test program was divided into two phases; (1) force and moment measurements were made with and without RCS blowing, investigating environment parameters (R sub e, Alpha, Beta), RCS plume parameters (Jet pressure ratio, momentum ratio and thrust level), and geometry parameters (RCS pod locations) on the orbiter model, (2) oil flow visualization tests were conducted on a dummy balance at the end of the test.
Monta, W. J.↗
An experimental investigation of leading-edge vortex augmentation by blowing
A wind tunnel test was conducted to determine the effects of over-the-wing blowing as a means of augmenting the leading-edge vortex flow of several pointed-tip, sharp-edged planforms. Arrow, delta, and diamond wings with leading-edge sweeps of 30 and 45 degrees were mounted on a body-of-revolution fuselage and tested in a low-speed wind tunnel at a Mach number of 0.2. Nozzle location data, pitch data, and flow-visualization pictures were obtained for a range of blowing rates. Results show pronounced increases in vortex lift due to the blowing.
Bradley, R. G.↗
Wind-tunnel free-flight investigation of a model of a spin-resistant fighter configuration
An investigation was conducted to provide some insight into the features affecting the high-angle-of-attack characteristics of a high-performance twin-engine fighter airplane which in operation has exhibited excellent stall characteristics with a general resistance to spinning. Various techniques employed in the study included wind-tunnel free-flight tests, flow-visualization tests, static force tests, and dynamic (forced-oscillation) tests. In addition to tests conducted on the basic configuration tests were made with the wing planform and the fuselage nose modified. The results of the study showed that the model exhibited good dynamic stability characteristics at angles of attack well beyond that for wing stall. The directional stability of the model was provided by the vertical tail at low and moderate angles of attack and by the fuselage forebody at high angles of attack. The wing planform was found to have little effect on the stability characteristics at high angles of attack. The tests also showed that although the fuselage forebody produced beneficial contributions to static directional stability at high angles of attack, it also produced unstable values of damping in yaw. Nose strakes located in a position which eliminated the beneficial nose contributions produced a severe directional divergence.
Grafton, S. B.↗
Phase change paint tests on Rockwell orbiter/tank and orbiter alone configurations (OH3A/OH3B)
Wind tunnel tests were conducted on scale models of the space shuttle orbiter and external tank. The tests were designed to determine the basic heating rate and interference effects on the orbiter-tank configuration and to analyze the effectiveness of the thermal protective system on the reentry vehicle. The phase change paint techniques were used to determine areodynamic heating rates. Oil flow and schlieren photographs were used for flow visualization.
Quan, M.↗