Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamical System Scaling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

LES simulations of a vacuum membrane distillation channel with geometric alterations

3D LES simulations were carried out to study the performance of a vacuum membrane distillation module. A wiggly wall profile with/without embedded stiffeners was considered to alleviate axial and radial temperature polarization, the cause of performance decrease in membrane distillation. Results of the flow field show the wiggles create unsteady vortex shedding inducing intense mixing in the channel. Vortex shedding intensity increases as the Reynolds number increases or stiffeners are added. 3D results show a 56% improvement in flux when moving from a flat sheet membrane to a wiggly membrane with stiffeners at a constant Reynolds number, corresponding to an improvement from 11.7 to 41.7 in the Nusselt number, showing that the alterations improved the flux performance by enhancing the heat transfer along the membrane surface and therefore alleviating temperature polarization, a critical bottleneck in membrane distillation systems. Further, a merit criterion was defined based on the Nusselt number and friction factor, and a 40% increase in merit was shown switching from a flat to a wiggly channel, while a 97% merit increase was seen going from flat to wiggly with stiffeners. A 42% enhancement in the flux was also seen moving from a straight channel to a wiggly channel at a higher Reynolds number which highlights the importance of strategically choosing the mass flow rate, as well as inducing flow separation and vortex shedding in the channel to promote mixing and dissipate the thermal boundary layer. The variation in results between the wiggly module with stiffeners and the wiggly module at high Reynolds numbers suggests enhancing mixing structures can be more impactful on flux for this geometry than increasing the flow rate to a turbulent/transitional regime. However, both are preferable for peak system flux performance. Furthermore, a 2D approximation was used to perform simulations on more extended channels to examine the length degradation. The modules with wiggly channels performed at the same flux level with a doubling of the length. On the other hand, the flat sheet modules experienced length degradation by temperature polarization and dropped in flux yield by around 13% of the short-channel value. This work illustrates that modeling the system and understanding how the performance decreases as the membrane surface area increases are critical for a larger module (scaling up from a lab to a prototype module) to maintain high flux performance.

42 ENGINEERING↗
DOE OSTI2020

Spatiotemporal Pattern Recognition in the PMU Signals in the WECC system

Phasor measurement unit (PMU) data has been used by multiple power system applications, including state estimation, post event analysis, oscillation detection, model validation, and many others. Still, due to its big data nature and availability to general research institutions, comprehensive understanding of the spatiotemporal patterns and underlying mechanisms are incomplete. This study applies a set of signal processing and machine learning approaches aiming at deciphering the characteristic behaviors of multiple phasor measurement units (PMUs) attributes (e.g., voltage, frequency, rate of change of frequency, phase angle), including their auto-correlation, cross-dependence, similarities and discrepancies across units and temporal scales, and distributions of anomalies and their linkages to potential external factors such as weather events. Data analytics are applied to PMUs from the U.S. Western Electricity Coordinating Council (WECC) system. The PMU measurements, recorded events, outages, and weather extremes are all from real world datasets. The findings from the study and mechanistic understanding of the PMU dynamics help provide guidance on system control or preventing blackouts. The derived metrics can be directly used for adjusting or filtering simulated PMU data used for advanced algorithm development.

Hou, Zhangshuan↗
DOE OSTI2022

Multi‐Layered Systems for Permanent Geologic Storage of CO 2 at the Gigatonne Scale

Abstract The effectiveness of Carbon Capture and Storage (CCS) as an imperative decarbonization technology relies on the sealing capacity of a fine‐grained caprock to permanently store CO 2 deep underground. Uncertainties in assessing the caprock sealing capacity increase with the spatial and temporal scales and may delay CCS deployment at the gigatonne scale. We have developed a computationally efficient transport model to capture the dynamics of basin‐wide upward CO 2 migration in a multi‐layered setting over geological time scales. We find that massive capillary breakthrough and viscous flow of CO 2 , even through pervasively fractured caprocks, are unlikely to occur and compromise the storage security. Potential leakage from the injection reservoir is hampered by repetitive layering of overlying caprocks. This finding agrees with geologic intuition and should be understandable by the public, contributing to the development of climate policies around this technology with increased confidence that CO 2 will be indefinitely contained in the subsurface.

58 GEOSCIENCES↗
DOE OSTI2023

Quantum simulation of exact electron dynamics can be more efficient than classical mean-field methods

Quantum algorithms for simulating electronic ground states are slower than popular classical mean-field algorithms such as Hartree–Fock and density functional theory but offer higher accuracy. Accordingly, quantum computers have been predominantly regarded as competitors to only the most accurate and costly classical methods for treating electron correlation. However, here we tighten bounds showing that certain first-quantized quantum algorithms enable exact time evolution of electronic systems with exponentially less space and polynomially fewer operations in basis set size than conventional real-time time-dependent Hartree–Fock and density functional theory. Although the need to sample observables in the quantum algorithm reduces the speedup, we show that one can estimate all elements of the k-particle reduced density matrix with a number of samples scaling only polylogarithmically in basis set size. We also introduce a more efficient quantum algorithm for first-quantized mean-field state preparation that is likely cheaper than the cost of time evolution. We conclude that quantum speedup is most pronounced for finite-temperature simulations and suggest several practically important electron dynamics problems with potential quantum advantage.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Hysteretic temperature sensitivity of wetland CH4 fluxes explained by substrate availability and microbial activity: Model Archive

This Modeling Archive is in support of an NGEE Arctic publication "Hysteretic temperature sensitivity of wetland CH4 fluxes explained by substrate availability and microbial activity" in the Journal Biogeosciences (https://doi.org/10.5194/bg-17-5849-2020), which includes the model data used in the publication. CH4 emissions from terrestrial systems are posited to increase, which can offset mitigation efforts and accelerate climate change. Yet, the accuracy of modeled CH4 emissions is sensitive to the prescribed CH4 production (or emission) temperature dependencies that are currently uncertain. Here, we use a comprehensive biogeochemistry model (ecosys) to investigate factors modulating CH4 production and emission rates across a permafrost thaw gradient encompassing a partly thawed bog and a fully thawed fen. We find that seasonally varying substrate availability drives lower and higher modeled methanogen biomass and activity, and thereby CH4 production, during the earlier and later periods of the thawed season, respectively. Package follows the Model data archiving guidelines with data in a *.zip file with three subfolders containing *.csv files and raw model output files; a data dictionary table (data_dictionary.csv) and two model output description tables (ecosys_plantspecies_output_notes.csv and ecosys_soil_ouput_notes.csv) to explain the format and meaning of individual output variables; and a user guide as a *.pdf. A detailed model description can be found in the supplement of (Grant, 2013). The ecosys source code is available at https://doi:10.5281/zenodo.3906642. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Shrub Seedling Experiment: Environmental Conditions, Vegetation Composition, and Seedling Recruitment, Seward Peninsula, Alaska, 2018-2019

In June 2018, a manipulative seed-addition experiment was established at the Council Mile Marker 71 (CN_MM71), Quartz Creek Burn Area (Kougarok Mile Marker 86), and Quartz Creek Unburned (Kougarok Mile Marker 80) sites on the Seward Peninsula, Alaska. At each site, 5 replicate blocks were established in disturbed and intact upland tussock tundra (a total of 40 plots). Disturbed plots at Council were located on thermo-erosional (thermokarst) slopes, while disturbed plots in Quartz Creek were in burned areas affected by the Mingvk Lake fire in 2015. Using a split-plot design, an additional manual disturbance treatment (scraping to remove the surface bryophyte layer) was implemented across all blocks in June 2018. Seeds of five erect, deciduous shrubs were broadcast seeded into each plot in June 2018, and seedlings were censused in August 2018 and August 2019. The dataset includes ancillary measurements of plot-level environmental conditions (soil temperature, moisture, chemistry, thaw depth, microtopography, substrate thickness) and vegetation composition (NDVI and estimated percent cover by species and plant functional type). Dataset contains 10 csv data files (five data files with corresponding data dictionaries and one file-level metadata file) and one pdf user guide. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Organismic materials for beyond von Neumann machines

The elementary basis of intelligence in organisms with a central nervous system includes neurons and synapses and their complex interconnections forming neural circuits. In non-neural organisms such as slime mold with gel-like media, viscosity modulation enables adaptation to changing environments. At a larger scale, collective intelligence emerges via social interactions and feedback in animal colonies. Learning and memory are therefore multi-scale features that evolve as a result of constant interactions with the environment. There is growing interest in emulating such features of intelligence in computing machines and autonomous systems. Materials that can respond to their environment in a manner similar to organisms (referred to as "organismic materials") therefore may be of interest as hardware components in artificial intelligence machines. In this brief review, we present a class of semiconductors called correlated oxides as candidates for learning machines. The term "correlated" refers to the fact that electrons in such lattices strongly interact and the ground state is not what is predicted by classical band theory. Such materials can undergo insulator-metal transitions at near ambient conditions under external stimuli such as thermal or electrical fields, strain, and chemical doping. Depending on the mechanism driving the transition, intermediate states can be metastable with different volatilities, and the time scales of phase change can be controlled over many orders of magnitude. The change in electronic properties can be sharp or gradual, leading to digital or analog behavior. These properties enable the realization of artificial neurons and synapses and emulate the associative and non-associative learning characteristics found in various organisms. We examine microscopic properties concerning electronic and structural transitions leading to collective behavior and theoretical treatments of the ground state and dynamical response, showcasing VO 2 as a model system. Next, we briefly review algorithms designed from the plasticity demonstrated by phase changing systems. Finally, we conclude the brief review with suggestions for future research toward realizing non-von Neumann machines.

42 ENGINEERING↗
DOE OSTI2024

Theory of capillary tension and interfacial dynamics of motility-induced phases

The statistical mechanics of equilibrium interfaces has been well-established for over a half century. In the past decade, a wealth of observations have made increasingly clear that a new perspective is required to describe interfaces arbitrarily far from equilibrium. In this work, beginning from microscopic particle dynamics that break time-reversal symmetry, we derive the linear interfacial dynamics of coexisting motility-induced phases. Doing so allows us to identify the athermal energy scale that excites interfacial fluctuations and the nonequilibrium surface tension that resists these excitations. Our theory identifies that, in contrast to equilibrium fluids, this active surface tension contains contributions arising from nonconservative forces which act to suppress interfacial fluctuations and, crucially, is distinct from the mechanical surface tension of Kirkwood and Buff. Here we find that the interfacial stiffness scales linearly with the intrinsic persistence length of the constituent active particle trajectories, in agreement with simulation data. We demonstrate that at wavelengths much larger than the persistence length, the interface obeys surface-area minimizing Boltzmann statistics with our derived nonequilibrium interfacial stiffness playing a role identical to that of equilibrium systems.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Contrasting Carbon–Water–Energy Dynamics in Perennial and Annual Bioenergy Agroecosystems Using Eddy Covariance and Interpretable Machine Learning

Understanding how agroecosystems respond to environmental variability is fundamental to predicting productivity and sustainability under a changing climate. We analyzed 55 site-years of high-frequency eddy covariance observations from five agroecosystems—two perennial grasses (miscanthus and switchgrass), two annual rotation systems (maize–soybean and sorghum–soybean), and a restored native prairie—to examine ecosystem-scale carbon, water, and energy fluxes. Using an interpretable machine-learning framework with regression tree ensembles, Shapley Additive Explanations, and Accumulated Local Effects, we quantified how environmental and temporal factors regulate gross primary productivity (GPP), evapotranspiration (ET), water-use efficiency, and the Bowen ratio. Perennials exhibited stronger physiological buffering and maintained fluxes across a broader range of temperature and moisture conditions, reflecting deeper rooting and persistent canopy cover. Annuals, in contrast, showed greater short-term variability and stronger coupling to atmospheric demand, with GPP and ET declining rapidly under low humidity or soil moisture. Differences in temperature sensitivity of Bowen ratio further revealed that perennials sustained proportionally greater sensible heat flux under cool conditions, whereas annuals exhibited constrained energy exchange when evaporative demand was low. Together, these results demonstrate that crop life cycle and canopy structure are fundamental determinants of ecosystem-scale carbon–water–energy coupling. By integrating long-term flux observations with interpretable machine learning, this study identifies the environmental drivers that shape agroecosystem function and highlights how conversion from annual to perennial feedstocks can enhance climatic resilience and alter land–atmosphere energy feedbacks. These findings provide a data-driven basis for improving crop and Earth-system models and for guiding bioenergy landscape design under future climate scenarios.

Accumulated Local Effects↗
DOE OSTI2023

Hierarchical multi-time-scale predictive thermal management and fuel optimization for heavy-duty compression ignition engines

For heavy-duty diesel engines, NO X emissions reduction is strongly constrained by fuel efficiency. This paper presents a hierarchical model predictive controller (H-MPC) for coordinated control of tailpipe NO X emissions and fuel consumption. The H-MPC uses the separation of slow and fast dynamics that exist in the engine and its aftertreatment system. The controller is synthesized with an architecture in which a high-level MPC uses a longer prediction horizon compared to the low-level predictive controller which tracks the high-level controller command and manages the thermal dynamics of the aftertreatment system. Engine load preview enables the high-level controller to estimate the desired catalyst temperature ahead of time and addresses the selective catalytic reduction (SCR) slow thermal dynamics. Calculated by the high-level controller, the intake manifold pressure, and the start of injection (SOI) crank angle is used as reference trajectories in the low-level controller that regulates fast dynamical behaviors such as engine out NO X emissions. Hardware-in-the-loop (HIL) validation of this integrated H-MPC on a rapid prototype controller shows that when the SCR catalyst temperature is above light-off temperature (warmed-up condition), the engine operation is shifted to operate with the best fuel economy since the warmed-up SCR can efficiently reduce the engine-out NO X emissions. Results indicate that up to 0.8% benefit in cycle averaged BSFC along with a 13% reduction in tailpipe NO X compared to a stock engine calibration can be achieved with the coordinated engine and aftertreatment system through H-MPC.

Engineering↗
DOE OSTI2022

Towards Digital and Performance-Based Supervisory HVAC Control Delivery

Upgrading supervisory HVAC control in commercial buildings is one of the most attractive decarbonization tools at our disposal. Modern controls are software programs and can in theory be deployed at scale and with a low up-front carbon "pulse". In practice, however, control delivery is a disjointed and inefficient process, dominated by manual handoffs of imprecise English language documents. A particularly high barrier exists between control implementation and building energy modeling (BEM) which results in control sequences typically not being tested for correctness or performance before implementation. Together with industry partners, DOE and the national labs are developing an ecosystem of tools and standards that can support fully digital performance-based control delivery workflows. This paper describes this ecosystem, which consists of three mutually supportive efforts. Semantic models of buildings and their systems enable automatic configuration and installation of control software. Platform-neutral control descriptions separate control algorithms from control platforms and enable the creation of libraries of reference control implementations. Dynamic whole-building energy-control simulation that can execute physically realistic control sequences makes it possible to test and evaluate the performance of control sequences and then directly compile them for installation and execution in control systems. In addition to digitizing and streamlining project-level control delivery, these standards and related software support benchmarking of control algorithms, both rule-based and optimization-based, and help to both advance the state of the art and to implement ratings and programs that encourage the adoption of high-performance control.

building controls↗
DOE OSTI2026

Ground and excited state gradients with end-to-end differentiable semiempirical quantum chemistry

Accurate and efficient gradients of molecular energy with respect to nuclear degrees of freedom are essential for geometry optimization and molecular dynamics, including simulations that go beyond the Born–Oppenheimer regime. A common approach involves deriving analytical formulas for new electronic structure methods, which is often conceptually difficult and requires tedious coding. Here, we implement analytical, semi-numerical, and automatic differentiation (AD)-based gradient pathways for semiempirical Hamiltonian models in the PYSEQM software package, leveraging both graphics processing unit (GPU) and central processing unit (CPU) architectures. We further extend these capabilities to excited states calculated using the configuration interaction singles and time-dependent Hartree–Fock ansätze. We benchmark wall time, peak memory usage, and accuracy across three molecular families of varying chemical complexity, including systems of up to a thousand atoms. For ground-state simulations, analytical and AD gradients achieve near-identical GPU runtimes, while semi-numerical gradients are slower on GPU but remain competitive on CPU. For excited states, both analytical and custom AD approaches using implicit differentiation show similar performance and low memory requirements, whereas gradients with full AD are memory-limited. AD gradients match analytical ones in accuracy across all tested systems, aided by a quaternion-based diatomic frame rotation for two-center quantities that ensures smooth energy surfaces. Overall, automatic differentiation emerges as a practical alternative to analytical gradients in semiempirical quantum chemistry, offering high accuracy while allowing seamless integration in AI-driven workflows and popular packages, such as PyTorch and JAX. Our results provide actionable guidance for selecting optimal gradient strategies in large-scale ground- and excited-state molecular dynamics simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Atomic force microscopy: Emerging illuminated and operando techniques for solar fuel research

Integrated photoelectrochemical devices rely on the synergy between components to efficiently generate sustainable fuels from sunlight. The micro- and/or nanoscale characteristics of the components and their interfaces often control critical processes of the device, such as charge-carrier generation, electron and ion transport, surface potentials, and electrocatalysis. Understanding the spatial properties and structure–property relationships of these components can provide insight into designing scalable and efficient solar fuel components and systems. These processes can be probed ex situ or in situ with nanometer-scale spatial resolution using emerging scanning-probe techniques based on atomic force microscopy (AFM). In this Perspective, we summarize recent developments of AFM-based techniques relevant to solar fuel research. We review recent progress in AFM for (1) steady-state and dynamic light-induced surface photovoltage measurements; (2) nanoelectrical conductive measurements to resolve charge-carrier heterogeneity and junction energetics; (3) operando investigations of morphological changes, as well as surface electrochemical potentials, currents, and photovoltages in liquids. Opportunities for research covered here include: (1) control of ambient conditions for performing AFM measurements; (2) in situ visualization of corrosion and morphological evolution of electrodes; (3) operando AFM techniques to allow nanoscale mapping of local catalytic activities and photo-induced currents and potentials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Machine learning of Kondo physics using variational autoencoders and symbolic regression

In this work, we employ variational autoencoders to extract physical insight from a dataset of one-particle Anderson impurity model spectral functions. Autoencoders are trained to find a low-dimensional, latent space representation that faithfully characterizes each element of the training set, as measured by a reconstruction error. Variational autoencoders, a probabilistic generalization of standard autoencoders, further condition the learned latent space to promote highly interpretable features. In our study, we find that the learned latent variables strongly correlate with well known, but nontrivial, parameters that characterize emergent behaviors in the Anderson impurity model. In particular, one latent variable correlates with particle-hole asymmetry, while another is in near one-to-one correspondence with the Kondo temperature, a dynamically generated low-energy scale in the impurity model. Using symbolic regression, we model this variable as a function of the known bare physical input parameters and "rediscover" the nonperturbative formula for the Kondo temperature. The machine learning pipeline we develop suggests a general purpose approach, which opens opportunities to discover new domain knowledge in other physical systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Synergistic Integration of Multiple Wave Energy Converters with Adaptive Resonance and Offshore Floating Wind Turbines through Bayesian Optimization

We developed a synergistic ocean renewable system where an array of Wave Energy Converters (WEC) with adaptive resonance was collocated with a Floating Offshore Wind Turbine (FOWT) such that the WECs, capturing wave energy through the resonance adapting to varying irregular waves, consequently reduced FOWFT loads and turbine motions. Combining Surface-Riding WECs (SR-WEC) individually designed to feasibly relocate their natural frequency at the peak of the wave excitation spectrum for each sea state, and to obtain the highest capture width ratio at one of the frequent sea states for annual average power in a tens of kilowatts scale with a 15 MW FOWT based on a semi-submersible, Bayesian Optimization is implemented to determine the arrangement of WECs that minimize the annual representation of FOWT’s wave excitation spectra. The time-domain simulation of the system in the optimized arrangement is performed, including two sets of interactions: one set is the wind turbine dynamics, mooring lines, and floating body dynamics for FOWT, and the other set is the nonlinear power-take-off dynamics, linear mooring, and individual WECs’ floating body dynamics. Those two sets of interactions are further coupled through the hydrodynamics of diffraction and radiation. For sea states comprising Annual Energy Production, we investigate the capture width ratio of WECs, wave excitation on FOWT, and nacelle acceleration of the turbine compared to their single unit operations. We find that the optimally arranged SR-WECs reduce the wave excitation spectral area of FOWT by up to 60% and lower the turbine’s peak nacelle acceleration by nearly 44% in highly occurring sea states, while multiple WECs often produce more than the single operation, achieving adaptive resonance with a larger wave excitation spectra for those sea states. The synergistic system improves the total Annual Energy Production (AEP) by 1440 MWh, and we address which costs of Levelized Cost Of Energy (LCOE) can be reduced by the collocation.

Engineering↗
DOE OSTI2020

Parallel algorithms for hyperdynamics and local hyperdynamics

Hyperdynamics (HD) is a method for accelerating the timescale of standard molecular dynamics (MD). It can be used for simulations of systems with an energy potential landscape that is a collection of basins, separated by barriers, where transitions between basins are infrequent. HD enables the system to escape from a basin more quickly while enabling a statistically accurate renormalization of the simulation time, thus effectively boosting the timescale of the simulation. In [Kim, Perez, Voter, J Chem Phys, 139:144110, 2013)1, a local version of HD was formulated, which exploits the intrinsic locality characteristic typical of most systems to mitigate the poor scaling properties of standard HD as the system size is increased. In this paper, we discuss how both HD and local HD can be formulated to run efficiently in parallel. We have implemented these ideas in the LAMMPS MD code, which means HD can be used with any interatomic potential LAMMPS supports. Together, these parallel methods allow simulations of any size to achieve the time acceleration offered by HD (which can be orders of magnitude), at a cost 3-5x that of standard MD. As examples, we performed two simulations of a million-atom system to model the diffusion and clustering of Pt adatoms on a large patch of Pt(100) surface for 80 and 160 μs.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Coupled Microbial-Conversion and Computational-Fluid-Dynamics (CFD) Models for Butanediol Production in Micro-Aerated Reactors

Microbial conversion of substrates to macromolecules has been widely used in the synthesis of value-added products in pharmaceutical and biotechnology industries. These bioreactions are also being investigated in the production of low-value commodities such as biofuels [1]. Gas-liquid mass-transfer and transport-reaction coupling are important challenges when designing and scaling up these reactor systems. Experiments in wellmixed small-scale reactors have enabled characterization of microbial reactivity, while their coupling with macroscale transport remains relatively unexplored. In this work, we use a coupled metabolic-CFD model to study the action of a genetically engineered microbe Zymomonas mobilis [2] on sugars to produce 2,3-Butanediol (BDO). BDO is an important hydrocarbon intermediate that can be catalytically upgraded to several fuels and chemicals [3]. An important aspect to this particular microbial conversion is the need for micro-aerated environments as opposed to traditional aerobic fermentation. Slight variations in oxygen concentration can result in competing reaction pathways that disable BDO production. Hence, gas-liquid mass transfer and transport need to be optimized in large-scale reactors to maximize BDO production, for which CFD is a valuable tool. The aerobic-fermentation CFD model previously developed by the authors [5] for simulating bubble-column and airlift reactors at scale was used in this study. The Reynolds-averaged mass, momentum and energy transport equations for interpenetrating gas and liquid phase are solved in this model along with the transport and interphase mass transfer of oxygen. Our previous work used a phenomenological model for microbial oxygen uptake that neglected microbial growth and other reaction pathways. In this work, a detailed metabolic model enabled prediction of product formation and inhibition pathways. In order to manage computational cost, we used a subcycling technique [6] that takes advantage of the clear separation in transport (~ 200 sec) and reaction (~ 2-3 hours) timescales. The CFD model is first solved to steady state, after which the metabolic model is advanced at every cell in the computational domain using the local oxygen concentration. The CFD model is then run to achieve a new steady state that provides a new oxygen distribution for the metabolic model. This process, where reaction and fluid updates are interleaved together, is iterated until reactants are completely exhausted. This work will examine the performance of different reactor designs such as bubble column and airlift reactors at scale (250-500 m3). Oxygen mass-transfer coefficient and distribution are critically analyzed among reactors, and optimization studies pertaining to aeration is presented. Furthermore, it has been observed in experiments that high BDO production may be achieved by manipulating the aerobic environment over the course of reaction, such that oxygen concentration is high during the growth phase, and very low as sugar is depleted. This characteristic will be addressed by our simulations for which a timedependent scheduling strategy for aeration is presented that maximizes BDO production. [1] Humbird, D., Davis, R., and McMillan, J., Aeration costs in stirred-tank and bubble column bioreactors, Biochemical Engineering Journal, 127, 161—166, 2017 [2] Yang, S., Mohagheghi, A., Franden, M. A., Chou, Y.-C., Chen, X., Dowe, N., Himmel, M. E., and Zhang, M., Metabolic engineering of zymomonas mobilis for 2, 3-butanediol production from lignocellulosic biomass sugars. Biotechnology for biofuels, 9(1):189, 2016 [3] Kim, S. J., Sim, H. J., Kim, J. W., Lee, Y. G., Park, Y. C., and Seo, J. H., Enhanced production of 2,3-butanediol from xylose by combinatorial engineering of xylose metabolic pathway and cofactor regeneration in pyruvate decarboxylase-deficient Saccharomyces cerevisiae. Bioresource Technology, 245:1551–1557, 2017 [4] Weller, H., Tabor, G., Jasak, H. and Fureby, C., A tensorial approach to computational continuum mechanics using object-oriented techniques, Computers in physics, 12, 6, 620--631, 1998

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

3D pattern formation of a protein–membrane suspension

Many essential cellular processes, including cell division and the establishment of cell polarity during embryogenesis, are regulated by pattern-forming proteins. These proteins often need to bind to a substrate, such as the cell membrane, onto which they interact and form two-dimensional (2D) patterns. It is unclear how the membrane’s continuity and dimensionality impact pattern formation. Here, we address this gap using the MinDE system, a prototypical example of pattern-forming membrane proteins. We show that when the lipid substrate is fragmented into submicrometer-sized diffusive liposomes, adenosine triphosphate-driven protein–protein interactions generate three-dimensional (3D) spatially extended patterns, despite the complete loss of membrane continuity. Remarkably, these 3D patterns emerge at scales four orders of magnitude larger than the individual liposomes. By systematically varying protein concentration, liposome size, and density, we observed and characterized a variety of 3D dynamical patterns not seen on continuous 2D membranes, including traveling waves, dynamical spirals, and a coexistence phase. Simulations and linear stability analysis of a coarse-grained model revealed that the physical properties of the dispersed membrane effectively rescale both the protein–membrane binding rates and diffusion, two key parameters governing pattern formation and wavelength selection. These findings highlight the robustness of Min’s pattern-forming ability, suggesting that protein–membrane suspensions could serve as an adaptable template for studying out-of-equilibrium self-organization in 3D, beyond in vivo contexts.

36 MATERIALS SCIENCE↗