Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Large transient fault current test of an electrical roll ring

The space station uses precision rotary gimbals to provide for sun tracking of its photoelectric arrays. Electrical power, command signals and data are transferred across the gimbals by roll rings. Roll rings have been shown to be capable of highly efficient electrical transmission and long life, through tests conducted at the NASA Lewis Research Center and Honeywell's Satellite and Space Systems Division in Phoenix, AZ. Large potential fault currents inherent to the power system's DC distribution architecture, have brought about the need to evaluate the effects of large transient fault currents on roll rings. A test recently conducted at Lewis subjected a roll ring to a simulated worst case space station electrical fault. The system model used to obtain the fault profile is described, along with details of the reduced order circuit that was used to simulate the fault. Test results comparing roll ring performance before and after the fault are also presented.

Yenni, Edward J.↗
NASA NTRS1992

A high speed signal processing system for a diode-pumped YAG lidar

Usually, in acquisition of the lidar echo signal, a transient recorder has been used. However, in the case of using a high-repetitive laser, such as a diode-pumped YAG laser, as a lidar light source, the acquisition speed of a transient recorder is not fast enough. A system using a sampling and direct accumulation in a clock cycle, before transferring digital data to a computer, is necessary for a fast acquisition, and a new system which equips the necessary functions was developed and is reported.

Okumura, H.↗
NASA NTRS1992

The multiple-function multi-input/multi-output digital controller system for the AFW wind-tunnel model

A real time multiple-function digital controller system was developed for the Active Flexible Wing (AFW) Program. The digital controller system (DCS) allowed simultaneous execution of two control laws: flutter suppression and either roll trim or a rolling maneuver load control. The DCS operated within, but independently of, a slower host operating system environment, at regulated speeds up to 200 Hz. It also coordinated the acquisition, storage, and transfer of data for near real time controller performance evaluation and both open- and closed-loop plant estimation. It synchronized the operation of four different processing units, allowing flexibility in the number, form, functionality, and order of control laws, and variability in the selection of the sensors and actuators employed. Most importantly, the DCS allowed for the successful demonstration of active flutter suppression to conditions approximately 26 percent (in dynamic pressure) above the open-loop boundary in cases when the model was fixed in roll and up to 23 percent when it was free to roll. Aggressive roll maneuvers with load control were achieved above the flutter boundary. The purpose here is to present the development, validation, and wind tunnel testing of this multiple-function digital controller system.

Hoadley, Sherwood T.↗
NASA NTRS1992

The multiple-function multi-input/multi-output digital controller system for the AFW wind tunnel model

A real-time multiple-function digital controller system was developed for the Active Flexible Wing (AFW) Program. The digital controller system (DCS) allowed simultaneous execution of two control laws: flutter suppression and either roll trim or a rolling maneuver load control. The DCS operated within, but independently of, a slower host operating system environment, at regulated speeds up to 200 Hz. It also coordinated the acquisition, storage, and transfer of data for near real-time controller performance evaluation and both open- and closed-loop plant estimation. It synchronized the operation of four different processing units, allowing flexibility in the number, form, functionality, and order of control laws, and variability in selection of sensors and actuators employed. Most importantly, the DCS allowed for the successful demonstration of active flutter suppression to conditions approximately 26 percent (in dynamic pressure) above the open-loop boundary in cases when the model was fixed in roll and up to 23 percent when it was free to roll. Aggressive roll maneuvers with load control were achieved above the flutter boundary.

Hoadley, Sherwood T.↗
NASA NTRS1991

Large transient fault current test of an electrical roll ring

The Space Station Freedom uses precision rotary gimbals to provide for sun tracking of its photoelectric arrays. Electrical power, command signals, and data are transferred across the gimbals by roll rings. Roll rings have been shown to be capable of highly efficient electrical transmission and long life, through tests conducted at the NASA Lewis Research Center and Honeywell's Satellite and Space Systems Division in Phoenix, AZ. Large potential fault currents inherent to the power system's DC distribution architecture have brought about the need to evaluate the effects of large transient fault currents on roll rings. A test recently conducted at Lewis subjected a roll ring to a simulated worst case space station electrical fault. The system model used to obtain the fault profile is described, along with details of the reduced order circuit that was used to simulate the fault. Test results comparing roll ring performance before and after the fault are also presented.

Yenni, Edward J.↗
NASA NTRS1992

Multiple-function multi-input/multi-output digital control and on-line analysis

The design and capabilities of two digital controller systems for aeroelastic wind-tunnel models are described. The first allowed control of flutter while performing roll maneuvers with wing load control as well as coordinating the acquisition, storage, and transfer of data for on-line analysis. This system, which employs several digital signal multi-processor (DSP) boards programmed in high-level software languages, is housed in a SUN Workstation environment. A second DCS provides a measure of wind-tunnel safety by functioning as a trip system during testing in the case of high model dynamic response or in case the first DCS fails. The second DCS uses National Instruments LabVIEW Software and Hardware within a Macintosh environment.

Hoadley, Sherwood T.↗
NASA NTRS1991

Thermal and structural analysis of the GOES scan mirror's on orbit performance

The on-orbit performance of the GOES satellite's scan mirror has been predicted by means of thermal, structural, and optical models. A simpler-than-conventional thermal model was used to reduce the time required to obtain orbital predictions, and the structural model was used to predict on-earth gravity sag and on-orbit distortions. The transfer of data from the thermal model to the structural model was automated for a given set of thermal nodes and structural grids.

Zurmehly, G. E.↗
NASA NTRS1992

Concurrent file operations in a high performance FORTRAN

Distributed memory multiprocessor systems can provide the computing power necessary for large scale scientific applications. A critical performance issue for a number of these applications is the efficient transfer of data to secondary storage. Recently several research groups have proposed FORTRAN language extensions for exploiting the data parallelism of such scientific codes on distributed memory architectures. However, few of these high performance FORTRAN's provide appropriate constructs for controlling the use of the parallel I/O capabilities of modern multiprocessing machines. In this paper, we propose constructs to specify I/O operations for distributed data structures in the context of Vienna Fortran. These operations can be used by the programmer to provide information which can help the compiler and runtime environment make the most efficient use of the I/O subsystem.

Brezany, Peter↗
NASA NTRS1992

The distributed virtual windtunnel

An implementation of a distributed virtual environment for the shared interactive visualization of large unsteady three-dimensional flowfields is described. Computation of the visualizations is performed on a Convex C3240 computer, and the visualization data are transferred over a high-speed network to a Silicon Graphics Iris workstation for rendering. A boom-mounted six-degree-of-freedom head-position-sensitive stereo CRT (cathode ray tube) system is used for display. A hand-position-sensitive glove controller is used for controlling various tracers for the visualization of the flow. User commands are sent to the Convex, which interprets these commands and computes the corresponding visualization. With this architecture, several users may share and cooperatively control the visualization generated by the Convex. The distributed architecture is also interesting to those using conventional screen and mouse interfaces.

Bryson, Steve↗
NASA NTRS1992

Simulation of particle mixing by turbulent convective flows on the connection machine

Mixing of particles by chaotic flow fields was simulated on the Connection Machine. Each cell was assigned to the processor, and the coordinates of particles residing on the cell were kept in the local memory of the processor. This approach implies the exchange between the local memories, when a particle moves from one cell to another. Approximately 10 exp 5 particles were injected into a time-dependent flow field obtained by solving the nonlinear system of partial differential equations describing turbulent thermal convection. The flow field was calculated on a CRAY, and data were transferred to a CM-200 through a high-speed HIPPI channel.

Malevsky, A. V.↗
NASA NTRS1993

Optimization of actuator arrays for aircraft interior noise control

A numerical procedure for grouping actuators in order to reduce the number of degrees of freedom in an active noise control system is evaluated using experimental data. Piezoceramic actuators for reducing aircraft interior noise are arranged into groups using a nonlinear optimization routine and clustering algorithm. An actuator group is created when two or more actuators are driven with the same control input. This procedure is suitable for active control applications where actuators are already mounted on a structure. The feasibility of this technique is demonstrated using measured data from the aft cabin of a Douglas DC-9 fuselage. The measured data include transfer functions between 34 piezoceramic actuators and 29 interior microphones and microphone responses due to the primary noise produced by external speakers. Control inputs for the grouped actuators were calculated so that a cost function, defined as a quadratic pressure term and a penalty term, was a minimum. The measured transfer functions and microphone responses are checked by comparing calculated noise reductions with measured noise reductions for four frequencies. The grouping procedure is then used to determine actuator groups that improve overall interior noise reductions by 5.3 to 15 dB, compared to the baseline experimental configuration.

Cabell, R. H.↗
NASA NTRS1996

Assessment of thermochemical nonequilibrium and slip effects for Orbital Reentry Experiment (OREX)

Results are provided from a viscous shock layer (VSL) analysis of the reentry flowfield around the forebody of the Japanese Orbital Reentry Experiment (OREX) vehicle. This vehicle is a 50 deg. spherically blunted cone with a nose radius of 1.35 m and a base diameter of 3.4 m. Calculations are done for the OREX trajectory from 105 to 48.4 km altitude range. A 7-species chemical model is found adequate for the flowfield analysis. However, for altitudes greater than 84 km, the low density effects (such as thermal nonequilibrium and slip) are to be implemented for good agreement between the predictions and flight inferred heat-transfer rate data. Further, at altitudes lower than 84 km, a finite surface recombination probability is to be employed in place of a non-catalytic surface for better comparison between the calculations and data. VSL results are also compared with the direct simulation Monte Carlo (DSMC) predictions at high altitudes (greater than 80 km) and the electron number density data for three altitudes in the OREX trajectory. Overall, there is a good comparison between the flight data and calculated results. With the ongoing refinements in data extraction procedures, the OREX data should prove valuable for validating theoretical models employed in flowfield codes for calculation of reacting-gas flowfields.

Gupta, Roop N.↗
NASA NTRS1997

High-Performance, Reliable Multicasting: Foundations for Future Internet Groupware Applications

Network protocols that provide efficient, reliable, and totally-ordered message delivery to large numbers of users will be needed to support many future Internet applications. The Reliable Multicast Protocol (RMP) is implemented on top of IP multicast to facilitate reliable transfer of data for replicated databases and groupware applications that will emerge on the Internet over the next decade. This paper explores some of the basic questions and applications of reliable multicasting in the context of the development and analysis of RMP.

Callahan, John↗
NASA NTRS1999

NCC: A Multidisciplinary Design/Analysis Tool for Combustion Systems

A multi-disciplinary design/analysis tool for combustion systems is critical for optimizing the low-emission, high-performance combustor design process. Based on discussions between NASA Lewis Research Center and the jet engine companies, an industry-government team was formed in early 1995 to develop the National Combustion Code (NCC), which is an integrated system of computer codes for the design and analysis of combustion systems. NCC has advanced features that address the need to meet designer's requirements such as "assured accuracy", "fast turnaround", and "acceptable cost". The NCC development team is comprised of Allison Engine Company (Allison), CFD Research Corporation (CFDRC), GE Aircraft Engines (GEAE), NASA Lewis Research Center (LeRC), and Pratt & Whitney (P&W). This development team operates under the guidance of the NCC steering committee. The "unstructured mesh" capability and "parallel computing" are fundamental features of NCC from its inception. The NCC system is composed of a set of "elements" which includes grid generator, main flow solver, turbulence module, turbulence and chemistry interaction module, chemistry module, spray module, radiation heat transfer module, data visualization module, and a post-processor for evaluating engine performance parameters. Each element may have contributions from several team members. Such a multi-source multi-element system needs to be integrated in a way that facilitates inter-module data communication, flexibility in module selection, and ease of integration.

Liu, Nan-Suey↗
NASA NTRS1999

On Estimating End-to-End Network Path Properties

The more information about current network conditions available to a transport protocol, the more efficiently it can use the network to transfer its data. In networks such as the Internet, the transport protocol must often form its own estimates of network properties based on measurements per-formed by the connection endpoints. We consider two basic transport estimation problems: determining the setting of the retransmission timer (RTO) for are reliable protocol, and estimating the bandwidth available to a connection as it begins. We look at both of these problems in the context of TCP, using a large TCP measurement set [Pax97b] for trace-driven simulations. For RTO estimation, we evaluate a number of different algorithms, finding that the performance of the estimators is dominated by their minimum values, and to a lesser extent, the timer granularity, while being virtually unaffected by how often round-trip time measurements are made or the settings of the parameters in the exponentially-weighted moving average estimators commonly used. For bandwidth estimation, we explore techniques previously sketched in the literature [Hoe96, AD98] and find that in practice they perform less well than anticipated. We then develop a receiver-side algorithm that performs significantly better.

Allman, Mark↗
NASA NTRS1999

Ground-Based Gas-Liquid Flow Research in Microgravity Conditions: State of Knowledge

During the last decade, ground-based microgravity facilities have been utilized in order to obtain predictions for spacecraft system designers and further the fundamental understanding of two-phase flow. Although flow regime, pressure drop and heat transfer coefficient data has been obtained for straight tubes and a limited number of fittings, measurements of the void fraction, film thickness, wall shear stress, local velocity and void information are also required in order to develop general mechanistic models that can be utilized to ascertain the effects of fluid properties, tube geometry and acceleration levels. A review of this research is presented and includes both empirical data and mechanistic models of the flow behavior.

McQuillen, J.↗
NASA NTRS2000

Unsteady High Turbulence Effects on Turbine Blade Film Cooling Heat Transfer Performance Using a Transient Liquid Crystal Technique

Unsteady wake effect, with and without trailing edge ejection, on detailed heat transfer coefficient and film cooling effectiveness distributions is presented for a downstream film-cooled gas turbine blade. Tests were performed on a five-blade linear cascade at an exit Reynolds number of 5.3 x 10(exp 5). Upstream unsteady wakes were simulated using a spoke-wheel type wake generator. Coolant blowing ratio was varied from 0.4 to 1.2; air and CO2 were used as coolants to simulate different density ratios. Surface heat transfer and film effectiveness distributions were obtained using a transient liquid crystal technique; coolant temperature profiles were determined with a cold wire technique. Results show that Nusselt numbers for a film cooled blade are much higher compared to a blade without film injection. Unsteady wake slightly enhances Nusselt numbers but significantly reduces film effectiveness versus no wake cases. Nusselt numbers increase only slic,htly but film cooling, effectiveness increases significantly with increasing, blowing ratio. Higher density coolant (CO2) provides higher effectiveness at higher blowing ratios (M = 1.2) whereas lower density coolant (Air) provides higher 0 effectiveness at lower blowing ratios (M = 0.8). Trailing edge ejection generally has more effect on film effectiveness than on the heat transfer, typically reducing film effectiveness and enhancing heat transfer. Similar data is also presented for a film cooled cylindrical leading edge model.

Han, J. C.↗
NASA NTRS2000

Performance Assessment of OVERFLOW on Distributed Computing Environment

The aerodynamic computer code, OVERFLOW, with a multi-zone overset grid feature, has been parallelized to enhance its performance on distributed and shared memory paradigms. Practical application benchmarks have been set to assess the efficiency of code's parallelism on high-performance architectures. The code's performance has also been experimented with in the context of the distributed computing paradigm on distant computer resources using the Information Power Grid (IPG) toolkit, Globus. Two parallel versions of the code, namely OVERFLOW-MPI and -MLP, have developed around the natural coarse grained parallelism inherent in a multi-zonal domain decomposition paradigm. The algorithm invokes a strategy that forms a number of groups, each consisting of a zone, a cluster of zones and/or a partition of a large zone. Each group can be thought of as a process with one or multithreads assigned to it and that all groups run in parallel. The -MPI version of the code uses explicit message-passing based on the standard MPI library for sending and receiving interzonal boundary data across processors. The -MLP version employs no message-passing paradigm; the boundary data is transferred through the shared memory. The -MPI code is suited for both distributed and shared memory architectures, while the -MLP code can only be used on shared memory platforms. The IPG applications are implemented by the -MPI code using the Globus toolkit. While a computational task is distributed across multiple computer resources, the parallelism can be explored on each resource alone. Performance studies are achieved with some practical aerodynamic problems with complex geometries, consisting of 2.5 up to 33 million grid points and a large number of zonal blocks. The computations were executed primarily on SGI Origin 2000 multiprocessors and on the Cray T3E. OVERFLOW's IPG applications are carried out on NASA homogeneous metacomputing machines located at three sites, Ames, Langley and Glenn. Plans for the future will exploit the distributed parallel computing capability on various homogeneous and heterogeneous resources and large scale benchmarks. Alternative IPG toolkits will be used along with sophisticated zonal grouping strategies to minimize the communication time across the computer resources.

Djomehri, M. Jahed↗