Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

Dual ion beam deposition of carbon films with diamondlike properties

A single and dual ion beam system was used to generate amorphous carbon films with diamond like properties. A methane/argon mixture at a molar ratio of 0.28 was ionized in the low pressure discharge chamber of a 30-cm-diameter ion source. A second ion source, 8 cm in diameter was used to direct a beam of 600 eV Argon ions on the substrates (fused silica or silicon) while the deposition from the 30-cm ion source was taking place. Nuclear reaction and combustion analysis indicate H/C ratios for the films to be 1.00. This high value of H/C, it is felt, allowed the films to have good transmittance. The films were impervious to reagents which dissolve graphitic and polymeric carbon structures. Although the measured density of the films was approximately 1.8 gm/cu cm, a value lower than diamond, the films exhibited other properties that were relatively close to diamond. These films were compared with diamondlike films generated by sputtering a graphite target.

Mirtich, M. J.↗

Dual-ion-beam deposition of carbon films with diamond-like properties

A single and dual ion beam system was used to generate amorphous carbon films with diamond like properties. A methane/argon mixture at a molar ratio of 0.28 was ionized in the low pressure discharge chamber of a 30-cm-diameter ion source. A second ion source, 8 cm in diameter was used to direct a beam of 600 eV Argon ions on the substrates (fused silica or silicon) while the deposition from the 30-cm ion source was taking place. Nuclear reaction and combustion analysis indicate H/C ratios for the films to be 1.00. This high value of H/C, it is felt, allowed the films to have good transmittance. The films were impervious to reagents which dissolve graphitic and polymeric carbon structures. Although the measured density of the films was approximately 1.8 gm/cu cm, a value lower than diamond, the films exhibited other properties that were relatively close to diamond. These films were compared with diamond like films generated by sputtering a graphite target.

Mirtich, M. J.↗

Black Carbon Aerosol Deposition Study (BCADS) Field Campaign Report

Black carbon (BC) absorbs incident solar radiation, perturbs temperature gradients in the atmosphere, and indirectly impacts cloud formation and optical properties (Koch and Del Genio 2010). Deposition of BC to snow and ice surfaces alters albedo and enhances snow melt (Hansen and Nazarenko 2004; Flanner et al., 2007). The impact of BC on regional and global climates through these processes depends on its atmospheric concentration, and thus on the relative rates of emission and loss. Combustion of fossil fuels and biofuel, biomass burning, and wildfires are major sources of BC (Bond et al., 2004). Significant sinks include wet and dry deposition. Wet deposition occurs through scavenging by cloud droplets, ice crystals, and precipitation, while dry deposition refers to the direct removal of particles in the atmosphere to planetary surfaces (e.g., plant, soil, ocean, ice surfaces). Bond et al. (2013) and references therein have focused on the source, aging, and optical properties of BC, while deposition components of the BC lifecycle remain poorly constrained. This is predominantly due to the lack of observations of both total aerosol and BC deposition. Removal rates of refractory and non-refractory sub-micron aerosol by wet and dry deposition are one of the most uncertain aspects of modelling cloud condensation nuclei (CCN; Lee et al., [2013]). BC is an ideal tracer for particle deposition because it is non-volatile and effectively chemically inert, though it can become mixed with other species in the atmosphere. Unlike other aerosol species, BC remains ‘intact’ in water and has no confounding gas-phase contribution to precipitation measurements, and can thus be used to examine the relative importance of wet and dry deposition. Thus, measurements of BC deposition are not only essential for constraining BC sinks and atmospheric lifetime, but also useful for investigating aerosol deposition more broadly.

Southern Great Plains, black carbon, aerosols, sin↗

Turbulence radiation coupling in boundary layers of heavy-duty diesel engines

The lack of accurate submodels for in-cylinder radiation and heat transfer has been identified as a key shortcoming in developing truly predictive, physics-based computational fluid dynamics (CFD) models that can be used to develop combustion systems for advanced high-efficiency, low-emissions engines. Recent measurements of wall layers in engines show discrepancies of up to 100% with respect to standard CFD boundary-layer models. And recent analysis of in-cylinder radiation based on the most recent spectral property databases and high-fidelity radiative transfer equation (RTE) solvers has shown that at operating pressures and exhaust-gas recirculation levels typical of modern heavy-duty compression-ignition engines, radiative emission can be as high as 40% of the wall heat losses, that molecular gas radiation (mainly CO2 and H2O) can be more important than soot radiation, and that a significant fraction of the emitted radiation can be reabsorbed before reaching the walls. That is, radiation not only contributes to heat losses, but also changes the in-cylinder temperature distribution, which in turn affects combustion and emissions. The goal of this research is to develop models that explicitly account for the potentially strong coupling between radiative and turbulent boundary layer heat transfer. For example, for optically thick conditions, a simple diffusion model might be formulated in terms of an absorption-coefficient-dependent turbulent Prandtl number.

Sircar, Arpan↗

Boosting the Activity of Pd Single Atoms by Tuning Their Local Environment on Ceria for Methane Combustion

Abstract Supported Pd single atom catalysts (SACs) have triggered great research interest in methane combustion yet with contradicting views on their activity and stability. Here, we show that the Pd SAs can take different electronic structure and atomic geometry on ceria support, resulting in different catalytic properties. By a simple thermal pretreatment to ceria prior to Pd deposition, a unique anchoring site is created. The Pd SA, taking this site, can be activated to Pd δ + (0< δ <2) that has greatly enhanced activity for methane oxidation: T 50 lowered by up to 130 °C and almost 10 times higher turnover frequency compared to the untreated catalyst. The enhanced activity of Pd δ + site is related to its oxygen‐deficient local structure and elongated interacting distance with ceria, leading to enhanced capability in delivering reactive oxygen species and decomposing reaction intermediates. This work provides insights into designing highly efficient Pd SACs for oxidation reactions.

Yang, Weiwei↗

Use of FGD gypsum in fire resistant panels

Gypsum from power plant flue gas desulphurization units (FGD gypsum) is a combustion by-product produced in high quantities. In this paper, gypsum panels composed of 100% FGD gypsum from two power plants have been subjected to different physico-chemical (density, pH, humidity), mechanical (flexural and compressive strength, surface hardness, impact resistance), fire resistance and environmental tests (leaching and radioactivity). The results obtained have been compared with the requirements established in some European standards for commercial gypsum and other standards for similar products. In addition, the panels manufactured have been compared with commercial gypsum panels in order to determine the recycling possibilities of this kind of material in this application.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The role of Sr doping on structure and microstructural properties of LaFeO{sub 3}

The doping of Strontium in LaFeO{sub 3} and its influence on the structural and microstructure properties were studied thoroughly. A few sets of Sr doping in La{sub (1-x)}Fe{sub x}O{sub 3}, where x=0.00, 0.02, and 0.06 were made through the solution combustion synthesis method using urea as fuel. X-ray diffraction was applied to get information about the structure and purity. The Rietveld refinement on X-ray diffraction peaks have been done, in order to calculate various structural parameters. The morphology of La{sub (1-x)}Sr{sub x}FeO{sub 3} nanoscale particles has been confirmed by field emission scanning electron microscopy (FESEM) technique. Differential scanning calorimetry (DSC) signals demonstrated the antiferromagnetic to paramagnetic transition (T{sub N}). The FTIR spectra was provided the information about various vibration modes in samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High Entropy Rare-earth Oxide (HERO) Coatings for Refractory Alloys

The HERO coating was developed to protect refractory alloys for application in the harsh hot section of the turbine engine environment addressing ARPA-E ULTIMATE Project Topic 2: Coating Development. The effort was both innovative in its utilization of high entropy rare earth oxides as well as transformational in our approach: holistic design of a single layer thermal/environmental barrier coating (T/EBC) for refractory alloys, with an excellent coefficient of thermal expansion (CTE) match to the alloy substrate, chemical compatibility with the underlying alloy, low oxidant permeability, stability in combustion environments, low thermal conductivity, thermal shock resistance, and resistance to degradation by siliceous debris (calcium magnesium alumino-silicates-CMAS). The high entropy rare earth oxide approach enables two critical coating properties: tailoring CTE match to the substrate and, most significantly, substantially reduced thermal conductivity. The summation of these proposed coating capabilities goes well beyond the technical requirements specified in the ULTIMATE program objectives, and additionally is essential for a successful first stage turbine blade application.

36 MATERIALS SCIENCE↗

Simulation Of The Internal-Combustion Engine

Program adapts to available information about particular engine. Mathematical model of internal-combustion engine constructed and implemented as computer program suitable for use on large digital computer systems. ZMOTTO program calculates Otto-cycle performance parameters as well as working-fluid compositions and properties throughout cycle for number of consecutive cycles and for variety of input parameters. Written in standard FORTRAN IV.

Zeleznik, Frank J.↗

Doppler-shifted fluorescence imaging of velocity fields in supersonic reacting flows

The application of Doppler-shifted fluorescence imaging of velocity fields in supersonic reacting flows is analyzed. Focussing on fluorescence of the OH molecule in typical H2-air Scramjet flows, the effects of uncharacterized variations in temperature, pressure, and collisional partner composition across the measurement plane are examined. Detailed measurements of the (1,0) band OH lineshape variations in H2-air combustions are used, along with single-pulse and time-averaged measurements of an excimer-pumped dye laser, to predict the performance of a model velocimeter with typical Scramjet flow properties. The analysis demonstrates the need for modification and control of the laser bandshape in order to permit accurate velocity measurements in the presence of multivariant flow properties.

Allen, M. G.↗

Time-History Statistics of Soot Formation in A Model Gas Turbine Combustor

Soot formation is a complex dynamic and intermittent process determined by properties of the fuel, combustor design, and combustor operation. Although the major steps in soot formation (i.e., formation of precursors, inception, growth and evolution) are similar for a variety of carbonaceous fuels, applications, and operating conditions, it remains unclear when the temporal transition between these steps occurs. An engineering prediction tool coupled with computational fluid physics (CFD), therefore needs to accurately model all these complex steps. To develop such a model, we propose the time-history concept for understanding the time dependency of soot formation as a function of local properties (i.e., temperature, velocity, local fuel air ratio, etc.). We continue our previous work with modeling the DLR aero-combustor [1] with our updated in-house CFD code, Open National Combustion Code (OpenNCC), that now includes a Multiple Time-Scale Flamelet Progress Variable approach and a the semi-empirical two-equation soot model. We injected massless tracer particles upstream of the injector region of the combustor to collect time-history statistics of the solution variables. The correlations between the collected statistics with respect to the experimental soot volume fraction data showed that time-history effect of certain flow variables, including turbulent kinetic energy (TKE), and multiple species is indeed important for soot formation. We then conducted a time-history based correlation analysis to determine the key species and the concentration ranges critical for soot formation (C6H5-based nucleation, acetylene-based surface growth, and oxidation with OH and O2). Based on the time-history correlation coefficient (THCC) analysis, we propose possible modifications to improve the current two-equation model.

LES↗

A computational investigation of diesel and biodiesel combustion and NOx formation in a light-duty compression ignition engine

Diesel and biodiesel combustion in a multi-cylinder light duty diesel engine were simulated during a closed cycle (from IVC to EVO), using a commercial computational fluid dynamics (CFD) code, CONVERGE, coupled with detailed chemical kinetics. The computational domain was constructed based on engine geometry and compression ratio measurements. A skeletal n-heptane-based diesel mechanism developed by researchers at Chalmers University of Technology and a reduced biodiesel mechanism derived and validated by Luo and co-workers were applied to model the combustion chemistry. The biodiesel mechanism contains 89 species and 364 reactions and uses methyl decanoate, methyl-9- decenoate, and n-heptane as the surrogate fuel mixture. The Kelvin-Helmholtz and Rayleigh-Taylor (KH-RT) spray breakup model for diesel and biodiesel was calibrated to account for the differences in physical properties of the fuels which result in variations in atomization and spray development characteristics. The simulations were able to capture the experimentally observed pressure and apparent heat release rate trends for both the fuels over a range of engine loads (BMEPs from 2.5 to 10 bar) and fuel injection timings (from 0° BTDC to 10° BTDC), thus validating the overall modeling approach as well as the chemical kinetic models of diesel and biodiesel surrogates. Moreover, quantitative NOx predictions for diesel combustion and qualitative NOx predictions for biodiesel combustion were obtained with the CFD simulations and the in-cylinder temperature trends were correlated to the NOx trends.

Wang, Zihan↗

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics

Highlights: • Briquetting was used to produce solid fuels from municipal solid waste and recycled plastics. • Optimal drying, processing temperature and pressure were found to produce stable briquettes. • Addition of waste plastics yielded heating values comparable with typical coal feedstocks. • This processing method improves utilization of paper and plastic diverted from landfills. - Abstract: Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in higher heating value. Analysis of the post-processing water uptake and compressive strength showed a correlation between density and stability to both mechanical stress and humid environment. Proximate analysis indicated heating values comparable to coal. The results showed that mechanical and moisture uptake stability were improved when the moisture and air contents were optimized. Moreover, the briquette sample composition was similar to biomass fuels but had significant advantages due to addition of waste plastics that have high energy content compared to other waste types. Addition of PP and HDPE presented better benefits than addition of PET due to lower softening temperature and lower oxygen content. It should be noted that while harmful emissions such as dioxins, furans and mercury can result from burning plastics, WTE facilities have been able to control these emissions to meet US EPA standards. This research provides a drop-in coal replacement that reduces demand on landfill space and replaces a significant fraction of fossil-derived fuel with a renewable alternative.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Leaching behaviour of bottom ash from RDF high-temperature gasification plants

This study investigated the physical properties, the chemical composition and the leaching behaviour of two bottom ash (BA) samples from two different refuse derived fuel high-temperature gasification plants, as a function of particle size. The X-ray diffraction patterns showed that the materials contained large amounts of glass. This aspect was also confirmed by the results of availability and ANC leaching tests. Chemical composition indicated that Fe, Mn, Cu and Cr were the most abundant metals, with a slight enrichment in the finest fractions. Suitability of samples for inert waste landfilling and reuse was evaluated through the leaching test EN 12457-2. In one sample the concentration of all metals was below the limit set by law, while limits were exceeded for Cu, Cr and Ni in the other sample, where the finest fraction showed to give the main contribution to leaching of Cu and Ni. Preliminary results of physical and geotechnical characterisation indicated the suitability of vitrified BA for reuse in the field of civil engineering. The possible application of a size separation pre-treatment in order to improve the chemical characteristics of the materials was also discussed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2009 Laser Diagnostics in Combustion GRC

Non-intrusive laser diagnostics for the spatially and temporally resolved measurement of temperature, chemical composition, and flow parameters have emerged over the last few decades as major tools for the study of both fundamental and applied combustion science. Many of the important advances in the field can be attributed to the discussions and ideas emanating from this meeting. This conference, originating in 1981 and held biennially, focuses on laser-based methods for measurement of both macroscopic parameters and the underlying microscale physical and chemical processes. Applications are discussed primarily to elucidate new chemical and physical issues and/or interferences that need to be addressed to improve the accuracy and precision of the various diagnostic approaches or to challenge the community of diagnosticians to invent new measurement techniques. Combustion environments present special challenges to the optical diagnostics community as they address measurements relevant to turbulence, spray and mixture formation, or turbulence/chemistry interactions important in practical combustion systems as well as fundamental chemical reactions in stationary laminar flames. The diagnostics considered may be generally classed as being incoherent, where the signals are radiated isotropically, or coherent, where the signals are generated in a directed, beam-like fashion. Both of the foregoing may employ either electronic or Raman resonance enhancement or a combination of both. Prominent incoherent approaches include laser induced fluorescence (LIF), spontaneous Raman scattering, Rayleigh scattering, laser induced incandescence, molecular flow tagging, and Mie scattering and their two- and three-dimensional imaging variants. Coherent approaches include coherent anti-Stokes Raman scattering (CARS), degenerate four wave mixing (DFWM), polarization spectroscopy (PS), laser induced grating spectroscopy (LIGS) and laser-based absorption spectroscopy. Spectroscopic modelling and validation are key elements to extract accurate parameter measurements and discussions focusing on key energy transfer processes, collisional models, and lineshapes. The properties and behaviour of lasers, optical arrangements and techniques, spectrally-selective and dispersive instruments and detectors are also important determinants of successful measurements and are discussed in detail. Recent developments in the conference have highlighted the application of techniques developed for combustion research that find application in other areas such as biological, atmospheric, chemical engineering or plasma processes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Addition of gaseous olefin to produce boiler fuel and stability studies

As a renewable liquid fuel, bio‐oil produced from fast pyrolysis of biomass is receiving increasing attention. However, bio‐oil has some negative properties, such as polymerization over time, high water content, high viscosity, and low energy value. It must be upgraded to be used as a fuel. The objective of this study was to develop an upgrading method by esterification and olefination reactions to produce bio‐oil with lower water content and higher energy value for combustion as a boiler fuel. Loblolly pine wood was pyrolyzed at a feed rate of ∼7 kg/h in a Mississippi State University proprietary auger reactor to produce bio‐oil with 65% yield. Upgrading reactions were performed in a high‐pressure batch autoclave. Bio‐oil was reacted with alcohols and gaseous olefins in the presence of a heterogeneous catalyst to produce upgraded bio‐oil. The influence of reaction conditions such as reaction time, reaction temperature, and catalyst content were evaluated. Physical and chemical properties such as acid value, higher heating value, water content, and optimal conditions were identified. The result of olefination shows improved bio‐oil quality and increased energy density. Accelerated aging tests were also performed. © 2014 American Institute of Chemical Engineers Environ Prog, 2014 34: 933–941, 2015

Tao, Jingming↗

From electronic structure to model application of key reactions for gasoline/alcohol combustion: Hydrogen-atom abstractions by $CH_3\dot{O}$ radical

H-atom abstraction by methoxy radical ($CH_3\dot{O}$) plays an important role in capturing the kinetics of reactions between gasoline components and alcohols. This study focuses on determining the reaction rates and thermodynamic properties of methoxy radical reactions with five gasoline fuel components: n-heptane, iso-octane, 1-hexene, cyclopentane and toluene. Electronic structure calculations were per-formed for all the stationary points with M06-2X/6 -311 ++ g(d,p) method. G3 composite method with atomization method is used for determining Δ f H 0 of all the closed shell and radical species, using which the necessary thermodynamic data of all the species was determined. Coupled cluster theory QCISD(T)/cc-pVXZ (where X = D and T) and Møller-Plesset perturbation theory MP2/cc-pVXZ (where X = D, T and Q) were used to calculate single point energies. Subsequently, rate constants for all hydrogen atom ab-straction channels have been performed using conventional transition state theory with unsymmetric tunneling corrections. A systematic comparison of rates for abstraction from different sites within the same species and same site from different species is done in order to get insights into this reaction class. Here, the computed thermodynamic properties and rate constants were incorporated into a recent gasoline mechanism to investigate the impact of the calculations performed in this work. A shift in predicted NTC (negative temperature coefficient) behavior and significant reduction in model reactivity is observed upon incorporating the rates calculated herein.

33 ADVANCED PROPULSION SYSTEMS↗

Structural and Magnetic Characteristics of Ferroxplana Co{sub 2}Y Nanoferrites Synthesized via Two Chemical Routes

Barium Y-type hexaferrite Ba{sub 2}Co{sub 2}Fe{sub 12}O{sub 22} nanopowders have been purposefully tailored using two different chemical wet methods, namely sol-gel auto-combustion (SGA) and co-precipitation (CP) routes. The impact of the pre-annealing and the annealing temperature of the formed precursors synthesized using two strategies on the structural, microstructure, and magnetic properties was investigated using x-ray diffraction (XRD), scanning electron microscopic (SEM), Fourier transform infrared spectroscopy (FT-IR), and vibrating sample magnetometer (VSM). For instance, well-defined Ba{sub 2}Co{sub 2}Fe{sub 12}O{sub 22} hexagonal plate-like particles was observed using SGA and CP routes for the precursors pre-annealed at 600 {sup ∘}C for 4 h and then annealed at low temperature 1000 {sup ∘}C for 2 h. The magnetic properties measured at room temperature evinced that hexaferrite Co{sub 2}Y particles have ferromagnetic characteristics. Good magnetic properties involving saturation magnetization (M{sub s}) of 23.64 and 24.37 emu/g and the coercivity (H{sub c}) of 417.76 and 280.92 Oe were accomplished for the samples pre-annealed at 600 {sup ∘}C for 4 h and then annealed at 1000 {sup ∘}C for 2 h for SGA and CP methods, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗