SEARCH · Engineering Papers

Results for “BENDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Properties and performance of fine-filament bronze-process Nb3Sn conductors

Fine-filament bronze-process Nb3Sn superconductors were fabricated to fulfill stringent requirements on critical current under tension in a one-inch bend diameter, current density, stability, and conductor losses. A large fraction of niobium filaments was incorporated in a bronze matrix, and a cable containing 4453 2-micron diameter filaments in each of six strands provided a current density of 85,000 A/sq cm at 10 to the -11th ohm-cm, 10 T, and 4.2 K. The next step was to incorporate copper stabilizer in a conductor with 20,538 filaments. These conductors, fabricated so that bend strains of about 1% would be experienced by the filaments in the one-inch bend, stably carried currents in the 200-500 A range. A quench current of 540 A in a 5-cm bend corresponds to 158,000 A/sq cm in the bronze and filament area, believed to be the highest critical current density reported for multifilamentary Nb3Sn.

Walker, M. S.↗

NASA NTRS1979

The structural behavior of a graphite-polymide honeycomb sandwich panel with quasi-isotropic face sheets and an orthotropic core

The results of a series of tests of graphite-polyimide honeycomb sandwich panels are presented. The panels were 1.22 m long, 0.508 m wide, and approximately 13.3 m thick. The face sheets were a T-300/PMR-15 fabric in a quasi-isotropic layup and were 0.279 mm thick. The core was Hexcel HRH 327-3/16 - 4.0 glass reinforced polyimide honeycomb, 12.7 mm thick. Three panels were used in the test: one was cut into smaller pieces for testing as beam, compression, and shear specimens; a second panel was used for plate bending tests; the third panel was used for in-plane stability tests. Presented are the experimental results of four point bending tests, short block compression tests, core transverse shear modulus, three point bending tests, vibration tests, plate bending tests, and panel stability tests. The results of the first three tests are used to predict the results of some of the other tests. The predictions and experimental results are compared, and the agreement is quite good.

Hyer, M. W.↗

NASA NTRS1981

Measurements of laminar and turbulent flow in a curved duct with thin inlet boundary layers

Laser Doppler velocimetry was used to measure the laminar and turbulent flow in a 90 deg square bend of strong curvature. The boundary layers at the inlet to the bend were approximately 25 percent and 15 percent of the hydraulic diameter for the laminar and turbulent flows, respectively. The development of the pressure driven secondary motion is more rapid for laminar flow: the maximum cross stream component measured was 60 percent of the bulk velocity in contrast to 40 percent for turbulent flow. The streamwise isotachs show that, for laminar flow, large velocities are found progressively nearer to the outer radius of the bend and along the sidewalls. For turbulent flow, the isotachs move towards the inner radius until about 60 deg around the bend where strong secondary motion results in a similar redistribution. Turbulence level and shear stress measurements are also presented.

Taylor, A. M. K. P.↗

NASA NTRS1981

An improved transverse shear deformation theory for laminated antisotropic plates

An improved transverse shear deformation theory for laminated anisotropic plates under bending is presented. The theory eliminates the need for an arbitrarily chosen shear correction factor. For a general laminate with coupled bending and stretching, the constitutive equations connecting resultants with average displacements and rotations are derived. Simplified forms of these relations are also obtained for the special case of a symmetric laminate with uncoupled bending. The governing equation for this special case is obtained as a sixth-order equation for the normal displacement requiring prescription of the three physically natural bounday conditions along each edge. For the limiting case of isotropy, the present theory reduces to an improved version of Mindlin's theory. Numerical results are obtained from the present theory for an example of a laminated plate under cylindrical bending. Comparison with results from exact three-dimensional analysis shows that the present theory is more accurate than other theories of equivalent order.

Murthy, M. V. V.↗

NASA NTRS1982

Developing flow in S-shaped ducts. 1: Square cross-section duct

Laser-Doppler velocimetry was used to measure the laminar and turbulent flow in an S-duct formed with two 22.5 deg sectors of a bend with ratio of mean radius of curvature to hydraulic diameter of 7.0. The boundary layers at the inlet to the bend were about 25% and 15% of the hydraulic diameter for the laminar and turbulent flows, respectively. Pressure-driven secondary flows develop in the first half of the S-duct and persist into the second half but are largely reversed by the exit plane as a consequence of the change in the sense of curvature. There is, however, a region near the outer wall of the second bend where the redistribution of the streamwise isotachs results in a reinforcement of the secondary flow which was established in the first half of the S-duct. The net redistribution of the streamwise isotachs is comparable to that occurring in unidirectional bends of stronger curvature. The wall pressure distribution was also measured for the turbulent flow and quantifies the expected large variations in the longitudinal pressure gradient distributions which occur at different radial locations.

Taylor, A. M. K. P.↗

NASA NTRS1982

Curved ducts with strong secondary motion - Velocity measurements of developing laminar and turbulent flow

Two orthogonal components of velocity and associated Reynolds stresses are determined in a square-sectioned, 90 degree bend of 2.3 radius ratio by utilizing laser-Doppler velocimetry for Reynolds numbers of 790 and 40,000. Results show that boundary layers at the bend inlet of 0.25 and 0.15 of the hydraulic diameter create secondary velocity maxima of 0.6 and 0.4 of the bulk flow velocity, respectively. It is concluded that the boundary layer thickness is important to the flow development, mainly in the first half of the bend, especially when it is reduced to 0.15 of the hydraulic diameter. Smaller secondary velocities are found for turbulent flow in an identical duct with a radius ratio of 7.0 than in the strongly curved bend, although their effect is more important to the streamwise flow development because of the smaller pressure gradients. In addition, the detail and accuracy of the measurements make them suitable for evaluation of numerical techniques and turbulence models.

Taylor, A. M. K. P.↗

NASA NTRS1984

Rapidly solidified NiAl and FeAl

Melt spinning was used to produce rapidly solidified ribbons of the B2 intermetallics NiAl and FeAl. Both Fe-40Al and Fe-45Al possessed some bend ductility in the as spun condition. The bend ductility of Fe-40Al, Fe-45Al, and equiatomic NiAl increased with subsequent heat treatment. Heat treatment at approximately 0.85 T (sub m) resulted in significant grain growth in equiatomic FeAl and in all the NiAl compositions. Low bend ductility in both FeAl and NiAl generally coincided with intergranular failure, while increased bend ductility was characterized by increasing amounts of transgranular cleavage fracture.

Gaydosh, D. J.↗

NASA NTRS1985

Flow control in a diffusing S-Duct

Accurate measurements have been made of secondary flow in a 1.51 area ratio diffusing 30 deg - 30 deg S-Duct with circulair cross section. Turbulent flow was entering the duct at Mach number of 0.6, the boundary layer thickness at the duct entrance was ten percent of the duct inlet diameter. Through measurements made, local flow velocity vector as well as static and total pressures mapping of the flow at several stations were obtained. Strong secondary flow was measured in the first bend which continued into the second bend with new vorticity produced in there in the opposite direction. Surface oil flow visualization and wall pressures indicated a region of separated flow starting at theta approximately equal to 22 deg on the inside of the first bend up to theta approximately equal to 44 deg on the outside of the second bend. The flow separated in 'cyclone' form and never reattached in the duct. As a result of the secondary flow and the flow separation, significant total pressure distortion was observed at the exit of the duct. Using flow control devices the separation was eliminated while the exit distortion was improved.

Vakili, A. D.↗

NASA NTRS1985

A nonlinear analysis of infinitely long graphite-epoxy cylindrical panels loaded with internal pressure

The structural response of internally pressurized composite cylindrical panels, representative of a transport aircraft's fuselage skins, is predicted by means of a one-dimensional, geometrically nonlinear analysis. An analytical study is conducted for the response of 4-, 8-, and 16-ply graphite/epoxy skins. The results obtained indicate that the response is geometrically nonlinear, and that a boundary layer with a severe bending gradient exists at the panel edges. The importance of through-the-thickness shearing deformations in the bending boundary layer is illustrated through comparison of analyses based on Kirchhoff-Love and shear deformation theories. Numerical results for the bending boundary layer lengths of the different panels are presented, and two bending boundary layers are predicted with the shear deformation theory.

Boitnott, R. L.↗

NASA NTRS1985

Rapidly solidified NiAl and FeAl

Gaydosh, D. J.↗

NASA NTRS1989

The prediction of secondary flow in curved ducts of square cross-section

A three-dimensional, fully-viscous Navier-Stokes code designated INS3D is presently used for the prediction of secondary and axial flows in curved ducts of square cross-section. Attention is given to a 90-deg bend, an S-shaped duct with two 22.5-deg bends, and an 180-deg bend. The sensitivity of predicted axial and secondary flows to grid resolution and artificial dissipation is investigated in the 90-deg bend case. Good agreement is found between predicted and experimentally measured flow components.

Mcconnaughey, P. K.↗

NASA NTRS1988

Experimental study of thin-walled composite beams

Thin-walled rectangular section composite beams are built out of graphite-epoxy prepreg tape using an autoclave molding technique. Cantilevered beams are tested under static loads using a specially-built apparatus and bending slope and elastic twist at a station are measured using a laser system. Measured bending slope and bending-induced twist distributions are correlated with predicted results obtained using a simple beam analysis as well as a refined finite element analysis. Natural vibration characteristics at different rotational speeds are determined experimentally by testing beams in a specially built 10 ft diameter vacuum chamber. The rotor is excited by piezo-electric crystals and response is determined from strain gages mounted on the surface. For composite beams with bending-twisting couplings (symmetric layup), effects of section warping and transverse shear on structural response are found to be substantial. These results were substantiated by the analyses.

Chandra, Ramesh↗

NASA NTRS1989

Cantilever clamp fitting

A device is disclosed for sealing and clamping a cylindrical element which is to be attached to an object such as a wall, a pressurized vessel or another cylindrical element. The device includes a gland having an inner cylindrical wall, which is threaded at one end and is attached at a bendable end to a deformable portion, which in turn is attached to one end of a conical cantilever structure. The other end of the cantilever structure connects at a bendable area to one end of an outer cylindrical wall. The opposite end of cylindrical wall terminates in a thickened portion, the radially outer surface of which is adapted to accommodate a tool for rotating the gland. The terminal end of cylindrical wall also includes an abutment surface, which is adapted to engage a seal, which in turn engages a surface of a receiver. The receiver further includes a threaded portion for engagement with the threaded portion of gland whereby a tightening rotation of gland relative to receiver will cause relative movement between cylindrical walls and of gland. This movement causes a rotation of the conical structure and thus a bending action at bending area and at the bending end of the upper end of inner cylindrical wall. These rotational and bending actions result in a forcing of the deformable portion radially inwardly so as to contact and deform a pipe. This forcible contact creates a seal between gland and pipe, and simultaneously clamps the pipe in position.

Melton, Patrick B.↗

NASA NTRS1991

Computational study of duct and pipe flows using the method of pseudocompressibility

A viscous, three-dimensional, incompressible, Navier-Stokes Computational Fluid Dynamics code employing pseudocompressibility is used for the prediction of laminar primary and secondary flows in two 90-degree bends of constant cross section. Under study are a square cross section duct bend with 2.3 radius ratio and a round cross section pipe bend with 2.8 radius ratio. Sensitivity of predicted primary and secondary flow to inlet boundary conditions, grid resolution, and code convergence is investigated. Contour and velocity versus spanwise coordinate plots comparing prediction to experimental data flow components are shown at several streamwise stations before, within, and after the duct and pipe bends. Discussion includes secondary flow physics, computational method, computational requirements, grid dependence, and convergence rates.

Williams, Robert W.↗

NASA NTRS1986

Gravitropism in higher plant shoots. IV - Further studies on participation of ethylene

Various hypotheses regarding the influence of ethylene on gravitropism in higher plant shoots were experimentally tested. It was found that ethylene at 1.0 and 10.0 cu cm/cu m decreased the rate of gravitropic bending in cocklebur stems, while 0.1 cm/cu m of ethylene had little effect. Treating cocklebur plants with 1.0 mmol aminoethoxyvinylglycine (AVG, an ethylene synthesis inhibitor) delayed stem bending compared with controls, but adding 0.1 cu cm/cu m ethylene in the surrounding atmosphere partially restored the rate of bending of AVG-treated plants. Virtually all newly synthesized ethylene appeared in bottom halves of horizontal stems, where ethylene concentrations were as much as 100 times those in upright stems or in top halves of horizontal stems. Auxin applied to one side of a vertical stem caused extreme bending away from that side; gibberellic acid, kinetin, and abscisic acid were without effect.

Wheeler, Raymond M.↗

NASA NTRS1935

Strength Tests of Thin-walled Duralumin Cylinders of Elliptic Section

This report is the fifth of a series presenting the results of strength tests of thin-walled cylinders and truncated cones of circular and elliptic section; it includes the results obtained from torsion tests on 30 cylinders, pure bending tests on 30 cylinders, and combined transverse shear and bending tests on 60 cylinders. All the cylinders tested were elliptic section with the ends clamped to rigid bulkheads. In the pure bending and combined transverse shear and bending tests the loads were applied in the plane of the major axis. The results of the tests on elliptic cylinders are correlated with the results of corresponding tests on circular cylinders and are presented in charts suitable for use in design.

STRESSED SKIN - CYLINDERS, ELLIPTIC - STRENGTH↗

NASA NTRS1943

Round Heat-treated Chromium-molybdenum-steel Tubing Under Combined Loads

The results of tests of round heat-treated chromium-molybdenum-steel tubing are presented. Tests were made on tubing under axial load, bending load, torsional load, combined bending and axial load, combined bending and torsional load, and combined axial, bending, and torsional load. Tensile and compressive tests were made to determine the properties of the material. Formulas are given for the evaluation of the maximum strength of this steel tubing under individual or combined loads. The solution of an example is included to show the procedure to be followed in designing a tubular cantilever member to carry combined loads.

Osgood, William R↗

NASA NTRS1942

Torsion Test of a Monocoque Box

A monocoque box beam consisting of a 24S-T aluminum-alloy sheet reinforced by four bulkheads and by longitudinal stringers and corner posts was subjected to bending loads as follows: pure bending about the lift axis, cantilever bending about the lift axis, and pure bending about both lift and drag axis. Longitudinal strains were measured for loads up to a load at which permanent set became measurable. The loads were sufficient to produce buckling of the sheet between stringers on the compression side of the box. The only noticeable effect of this buckling was a small increase in extreme-fiber strain on the compression side. The measured strains and measured deflections differed less than 10 percent from those computed from the simple beam theory after taking account of the effective width of the buckled sheet. The effect of the bulkheads on the distribution of stringer strain was negligible.

Mcpherson, Albert E↗