Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Airframes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

Application of the joined wing to tiltrotor aircraft

A study was made to determine the potential speed improvements and other benefits resulting from the application of the joined wing concept to tiltrotor aircraft. Using the XV-15 as a baseline, the effect of replacing the cantilever wing by a joined-wing pair was studied. The baseline XV-15 cantilever wing has a thickness/chord ratio of 23 percent. It was found that this wing could be replaced by a joined-wing pair of the same span and total area employing airfoils of 12 percent thickness/chord ratio. The joined wing meets the same static strength requirements as the cantilever wing, but increases the limiting Mach Number of the aircraft from M=0.575 to M=0.75, equivalent to an increase of over 100 knots in maximum speed. The joined wing configuration studied is lighter than the cantilever and has approximately 11 percent less wing drag in cruise. Its flutter speed of 245 knots EAS is not high enough to allow the potential Mach number improvement to be attained at low altitude. The flutter speed can be raised either by employing rotors which can be stopped and folded in flight at speeds below 245 knots EAS, or by modifying the airframe to reduce adverse coupling with the rotor dynamics. Several modifications of wing geometry and nacelle mass distribution were investigated, but none produced a flutter speed above 260 knots EAS. It was concluded that additional research is required to achieve a more complete understanding of the mechanism of rotor/wing coupling.

Wolkovitch, Julian↗

Opportunities for improved understanding of supersonic and hypersonic flows

This overview describes some of the diverse applications which are foreseen in the supersonic and hypersonic regime, and points out both the need and the opportunity for improved understanding of the subject. New facilities and experimental test techniques combined with computational fluid dynamics methods are described to illustrate challenging flows over supersonic wings, separated free-shear mixing layers, and in scramjet-airframe integration.

Jones, Robert A.↗

Proposed definition of the term en route in en route aircraft noise

The problem of en route aircraft noise was examined in a formal, dedicated, setting. Whereas the general meaning of the term en route might be intuitively understood, it is suggested that a precise formal definition of the term en route would be opportune from the outset, especially since the scientific and technical investigation of the problem of noise immissions on the ground from aircraft in flight away from the airspace of an airport may conceivably lead to administrative, regulatory, and legal consequences that would mandatorily require a precise definition of the term en route. Five flight segments, with their differing airframe configurations, engine thrusts, and airspeed management, should form the basis for the differential consideration of the noise immissions perceived on the ground underneath or near the defined segments of the flightpath in en route flight, from the end of the initial climb from an airport after takeoff until the final approach to an airport.

Garbell, Maurice A.↗

Hot gas ingestion characteristics and flow visualization of a vectored thrust STOVL concept

A 9.2 percent scale short takeoff and vertical landing (STOVL) hot gas ingestion model was designed and built by McDonnell Douglas Corporation (MCAIR) and tested in the NASA Lewis Research Center 9- by 15-Foot Low Speed Wind Tunnel (LSWT). Hot gas ingestion, the entrainment of heated engine exhaust into the inlet flow field, is a key development issue for advanced short takeoff and vertical landing aircraft. The Phase 1 test program, conducted by NASA Lewis and McDonnell Douglas Corporation, evaluated the hot ingestion phenomena and control techniques and Phase 2 test program which was conducted by NASA Lewis are both reported. The Phase 2 program was conducted at exhaust nozzles temperatures up to 1460 R and utilized a sheet laser system for flow visualization of the model flow field in and out of ground effects. Hot gas ingestion levels were measured for the several forward nozzle splay configurations and with flow control/lift improvement devices which reduced the hot gas ingestion. The model support system had four degrees of freedom, heated high pressure air for nozzle flow, and a suction system exhaust for inlet flow. The headwind (freestream) velocity for Phase 1 was varied from 8 to 90 kn, with primary data taken in the 8 to 23 kn headwind velocity range. Phase 2 headwind velocity varied from 10 to 23 kn. Results of both Phase 1 and 2 are presented. A description of the model, facility, a new model support system, and a sheet laser illumination system are also provided. Results are presented over a range of main landing gear height (model height) above the ground plane at a 10 kn headwind velocity. The results contain the compressor face pressure and temperature distortions, total pressure recovery, compressor face temperature rise, and the environmental effects of the hot gas. The environmental effects include the ground plane temperature and pressure distributions, model airframe heating, and the location of the ground flow separation. Results from the sheet laser flow visualization test are also shown.

Johns, Albert L.↗

NASA Langley Research Center National Aero-Space Plane Mission simulation profile sets

To provide information on the potential for long life service of oxidation resistant carbon-carbon (ORCC) materials in the National Aero-Space Plane (NASP) airframe environment, NASP ascent, entry, and cruise trajectories were analytically flown. Temperature and pressure profiles were generated for 20 vehicle locations. Orbital (ascent and entry) and cruise profile sets from four locations are presented along with the humidity exposure and testing sequences that are being used to evaluate ORCC materials. The four profiles show peak temperatures during the ascent leg of an orbital mission of 2800, 2500, 2000, and 1700 F. These profiles bracket conditions where carbon-carbon might be used on the NASP vehicle.

Ohlhorst, Craig W.↗

In-flight investigation of shuttle tile pressure orifice installations

To determine shuttle orbiter wing loads during ascent, wing load instrumentation was added to Columbia (OV-102). This instrumentation included strain gages and pressure orifices on the wing. The loads derived from wing pressure measurements taken during STS 61-C did not agree with those derived from strain gage measurements or with the loads predicted from the aerodynamic database. Anomalies in the surface immediately surrounding the pressure orifices in the thermal protection system (TPS) tiles were one possible cause of errors in the loads derived from wing pressure measurements. These surface anomalies were caused by a ceramic filler material which was installed around the pressure tubing. The filler material allowed slight movement of the TPS tile and pressure tube as the airframe flexed and bent under aerodynamic loads during ascent and descent. Postflight inspection revealed that this filler material had protruded from or receeded beneath the surface, causing the orifice to lose its flushness. Flight tests were conducted at NASA Ames Research Center Dryden Flight Research Facility to determine the effects of any anomaly in surface flushness of the orifice installation on the measured pressures at Mach numbers between 0.6 and 1.4. An F-104 aircraft with a flight test fixture mounted beneath the fuselage was used for these flights. Surface flushness anomalies typical of those on the orbiter after flight (STA 61-C) were tested. Also, cases with excessive protrusion and recession of the filler material were tested. This report shows that the anomalies in STS 61-C orifice installations adversely affected the pressure measurements. But the magnitude of the affect was not great enough to account for the discrepancies with the strain gage measurements and the aerodynamic predictions.

Moes, Timothy R.↗

Advancements in frequency-domain methods for rotorcraft system identification

A new method for frequency-domain identification of rotorcraft dynamics is presented. Nonparametric frequency-response identification and parametric transfer-function modeling methods are extended to allow the extraction of state-space (stability and control derivative) representations. An interactive computer program DERIVID is described for the iterative solution of the multi-input/multi-output frequency-response matching approach used in the identification. Theoretical accuracy methods are used to determine the appropriate model structure and degree-of-confidence in the identified parameters. The method is applied to XV-15 tilt-rotor aircraft data in hover. Bare-airframe stability and control derivatives for the lateral/directional dynamics are shown to compare favorably with models previously obtained using time-domain identification methods and the XV-15 simulation program.

Tischler, Mark B.↗

Scaling effects in the impact response of graphite-epoxy composite beams

In support of crashworthiness studies on composite airframes and substructure, an experimental and analytical study was conducted to characterize size effects in the large deflection response of scale model graphite-epoxy beams subjected to impact. Scale model beams of 1/2, 2/3, 3/4, 5/6, and full scale were constructed of four different laminate stacking sequences including unidirectional, angle ply, cross ply, and quasi-isotropic. The beam specimens were subjected to eccentric axial impact loads which were scaled to provide homologous beam responses. Comparisons of the load and strain time histories between the scale model beams and the prototype should verify the scale law and demonstrate the use of scale model testing for determining impact behavior of composite structures. The nonlinear structural analysis finite element program DYCAST (DYnamic Crash Analysis of STructures) was used to model the beam response. DYCAST analysis predictions of beam strain response are compared to experimental data and the results are presented.

Jackson, Karen E.↗

A computational study of the impingement region of an unsteady subsonic jet

Vertical/Short Take-Off and Landing (V/STOL) aircraft may encounter operating difficulties while hovering near the ground. Lift loss, hot gas and debris ingestion, and landing surface damage are some of the potential problems which can result from the interaction of the propulsive jets with the airframe and ground. The purpose of the present work is to develop a detailed understanding of a flowfield, a jet exiting from a flat plate impacting a ground plane, that contains much of the essential physics of the complex flows encountered by V/STOL aircraft in hover. To achieve this, a high-resolution time-accurate numerical simulation of the impinging jet flow was performed. The numerical simulation is based on the solution of the laminar compressible Navier-Stokes equations using the Beam-Warming algorithm. Complex start-up and periodic jet and jet-induced vortex structures were captured, including the formation of primary and secondary jet-induced vortices and wall-jet separation. The formation and development of these phenomena are supported by experimental measurements and smoke visualization. Results are compared with appropriate experiments.

Jalamani, Zakaria A.↗

Calculation of hypersonic forebody/inlet flow fields

The National Aero-Space Plane (NASP) is unique in its integration of the airframe and propulsion system. The performance of the NASP propulsion system (scramjet) is dependent upon the quality of the flow into the scramjet inlet. Hence, the calculation of the inlet flow field must be coupled to the forebody flow field for accurate performance predictions. The Compressible Navier-Stokes code has been extended to perform both external and internal hypersonic flow fields. Computations are presented that validate these changes and demonstrate the capability to perform coupled forebody/inlet computations for hypersonic flows.

Bennett, Bradford C.↗

Analysis of airframe/engine interactions - An integrated control perspective

Techniques for the analysis of the dynamic interactions between airframe/engine dynamical systems are presented. Critical coupling terms are developed that determine the significance of these interactions with regard to the closed loop stability and performance of the feedback systems. A conceptual model is first used to indicate the potential sources of the coupling, how the coupling manifests itself, and how the magnitudes of these critical coupling terms are used to quantify the effects of the airframe/engine interactions. A case study is also presented involving an unstable airframe with thrust vectoring for attitude control. It is shown for this system with classical, decentralized control laws that there is little airframe/engine interaction, and the stability and performance with those control laws is not affected. Implications of parameter uncertainty in the coupling dynamics is also discussed, and effects of these parameter variations are also demonstrated to be small for this vehicle configuration.

Schmidt, David K.↗

Convertible engine system for high speed rotorcraft

The identification of engine technology needed for high speed rotorcraft and to also provide suitable propulsion data for the High Speed Rotor Craft is presented. The several objectives are: (1) to generate technology planning data for NASA, (2) to help understand the propulsion requirements of new aircraft types being considered, and (3) to have a source of consistent engine data for the airframe companies doing the studies. This study is primarily directed at Folding Tilt Rotor types with some consideration given to the X-Wing type.

Hirschkron, R.↗

3-D Euler calculations for aft-propfan integration

The problem of reducing engine-airframe installation drag for a transport aircraft with an aft-mounted propfan or turboprop engine is investigated. A three-dimensional Euler code is used for the analysis. Installation drag effects are inferred from a qualitative analysis of the computed velocity and pressure distributions. The basic design philosophy is to alleviate flow acceleration near the strut/nacelle junction by aerodynamic means. This involves minor reshaping and relocation of the propulsion system.

Naik, Dinesh A.↗

Hypersonic CFD applications for the National Aero-Space Plane

Design and analysis of the NASP depends heavily upon developing the critical technology areas that cover the entire engineering design of the vehicle. These areas include materials, structures, propulsion systems, propellants, integration of airframe and propulsion systems, controls, subsystems, and aerodynamics areas. Currently, verification of many of the classical engineering tools relies heavily on computational fluid dynamics. Advances are being made in the development of CFD codes to accomplish nose-to-tail analyses for hypersonic aircraft. Additional details involving the partial development, analysis, verification, and application of the CFL3D code and the SPARK combustor code are discussed. A nonequilibrium version of CFL3D that is presently being developed and tested is also described. Examples are given of portion calculations for research hypersonic aircraft geometries and comparisons with experiment data show good agreement.

Richardson, Pamela F.↗

Rotor systems research aircraft risk-reduction shake test

A shake test and an extensive analysis of results were performed to evaluate the possibility of and the method for dynamically calibrating the Rotor Systems Research Aircraft (RSRA). The RSRA airframe was subjected to known vibratory loads in several degrees of freedom and the responses of many aircraft transducers were recorded. Analysis of the transducer responses using the technique of dynamic force determination showed that the RSRA, when used as a dynamic measurement system, could predict, a posteriori, an excitation force in a single axis to an accuracy of about 5 percent and sometimes better. As the analysis was broadened to include multiple degrees of freedom for the excitation force, the predictive ability of the measurement system degraded to about 20 percent, with the error occasionally reaching 100 percent. The poor performance of the measurement system is explained by the nonlinear response of the RSRA to vibratory forces and the inadequacy of the particular method used in accounting for this nonlinearity.

Wellman, J. Brent↗

The Integrated Airframe/Propulsion Control System Architecture program (IAPSA)

The Integrated Airframe/Propulsion Control System Architecture program (IAPSA) is a two-phase program which was initiated by NASA in the early 80s. The first phase, IAPSA 1, studied different architectural approaches to the problem of integrating engine control systems with airframe control systems in an advanced tactical fighter. One of the conclusions of IAPSA 1 was that the technology to construct a suitable system was available, yet the ability to create these complex computer architectures has outpaced the ability to analyze the resulting system's performance. With this in mind, the second phase of IAPSA approached the same problem with the added constraint that the system be designed for validation. The intent of the design for validation requirement is that validation requirements should be shown to be achievable early in the design process. IAPSA 2 has demonstrated that despite diligent efforts, integrated systems can retain characteristics which are difficult to model and, therefore, difficult to validate.

Daniel L Palumbo↗

A three-dimensional application with the numerical grid generation code: EAGLE (utilizing an externally generated surface)

Program EAGLE (Eglin Arbitrary Geometry Implicit Euler) is a multiblock grid generation and steady-state flow solver system. This system combines a boundary conforming surface generation, a composite block structure grid generation scheme, and a multiblock implicit Euler flow solver algorithm. The three codes are intended to be used sequentially from the definition of the configuration under study to the flow solution about the configuration. EAGLE was specifically designed to aid in the analysis of both freestream and interference flow field configurations. These configurations can be comprised of single or multiple bodies ranging from simple axisymmetric airframes to complex aircraft shapes with external weapons. Each body can be arbitrarily shaped with or without multiple lifting surfaces. Program EAGLE is written to compile and execute efficiently on any CRAY machine with or without Solid State Disk (SSD) devices. Also, the code uses namelist inputs which are supported by all CRAY machines using the FORTRAN Compiler CF177. The use of namelist inputs makes it easier for the user to understand the inputs and to operate Program EAGLE. Recently, the Code was modified to operate on other computers, especially the Sun Spare4 Workstation. Several two-dimensional grid configurations were completely and successfully developed using EAGLE. Currently, EAGLE is being used for three-dimension grid applications.

Houston, Johnny L.↗

Concept development of a Mach 4 high-speed civil transport

A study was conducted to configure and analyze a 250 passenger, Mach 4 High Speed Civil Transport with a design range of 6500 n.mi. The design mission assumed an all-supersonic cruise segment and no community noise or sonic boom constraints. The study airplane was developed in order to examine the technology requirements for such a vehicle and to provide an unconstrained baseline from which to assess changes in technology levels, sonic boom limits, or community noise constraints in future studies. The propulsion, structure, and materials technologies utilized in the sizing of the study aircraft were assumed to represent a technology availability date of 2015. The study airplane was a derivative of a previously developed Mach 3 concept and utilized advanced afterburning turbojet engines and passive airframe thermal protection. Details of the configuration development, aerodynamic design, propulsion system, mass properties, and mission performance are presented. The study airplane was estimated to weigh approx. 866,000 lbs. Although an aircraft of this size is a marginally acceptable candidate to fit into the world airport infrastructure, it was concluded that the inclusion of community noise or sonic boom constraints would quickly cause the aircraft to grow beyond acceptable limits using the assumed technology levels.

Domack, Christopher S.↗