Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “turbulent flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

Factors Affecting Laminar Boundary Layer Measurements in a Supersonic Stream

The observed discrepancy at supersonic speeds between theoretical and apparent experimental average flat plate friction-drag coefficients calculated from boundary layer total-pressure surveys was investigated. Effects of the total-pressure probe, heat transfer through the leading edge region, change in leading-edge radius and strength of the leading-edge wave, possible early transition to turbulent flow or “bursts of turbulence,” and the slight stream-wise pressure gradient inherent in flat plate flow were investigated for plates with very sharp leading edges. Only one of these factors, the effect of the total-pressure probe, was found to be significant. Total-pressure probes of different tip heights, when placed in laminar boundary layers developing under identical conditions, were found to yield different values of friction drag coefficient. Extrapolation of these measurements indicates that a probe of vanishing size would yield the theoretical predicted values of average flat plate friction-drag coefficients. A correlation describing the relation between the friction-drag discrepancy and the probe tip height is presented.

Blue, Robert E↗
NASA NTRS1973

A study of the local pressure field in turbulent shear flow and its relation to aerodynamic noise generation

Work during the period of this report has been in three areas: (1) pressure transducer error analysis, (2) fluctuating velocity and pressure measurements in the NASA Lewis 6-inch diameter quiet jet facility, and (3) measurement analysis. A theory was developed and experimentally verified to quantify the pressure transducer velocity interference error. The theory and supporting experimental evidence show that the errors are a function of the velocity field's turbulent structure. It is shown that near the mixing layer center the errors are negligible. Turbulent velocity and pressure measurements were made in the NASA Lewis quiet jet facility. Some preliminary results are included.

Jones, B. G.↗
NASA NTRS1974

Combustion generated noise in gas turbine combustors

Experiments were conducted to determine the noise power and spectra emitted from a gas turbine combustor can exhausting to the atmosphere. Limited hot wire measurements were made of the cold flow turbulence level and spectra within the can. The fuels used were JP-4, acetone and methyl alcohol burning with air at atmospheric pressure. The experimental results show that for a fixed fuel the noise output is dominated by the airflow rate and not the fuel/air ratio. The spectra are dominated by the spectra of the cold flow turbulence spectra which were invariant with airflow rate in the experiments. The effect of fuel type on the noise power output was primarily through the heat of combustion and not the reactivity. A theory of combustion noise based upon the flame radiating to open surroundings is able to reasonably explain the observed results. A thermoacoustic efficiency for noise radiation as high as .00003 was observed in this program for JP-4 fuel. Scaling rules are presented for installed configurations.

Strahle, W. C.↗
NASA NTRS1996

Simulation of Three-Dimensional Symmetric and Asymmetric Instabilities in Attachment-Line Boundary Layers

On a swept wing, contamination along the leading edge, Tollmien-Schlichting waves, stationary or traveling crossflow vortices, and/or Taylor-Gortler vortices can cause the catastrophic breakdown of laminar to turbulent flow, which leads to increased skin-friction drag for the aircraft. The discussion in this Note will be limited to disturbances which evolve along the attachment line (leading edge of swept wing). If the Reynolds number of the attachment-line boundary layer is greater than some critical value, then the complete wing is inevitably engulfed in turbulent flow. Essentially, there are two critical Reynolds number points that must be considered. The first is for small-amplitude disturbances, and the second is for bypass transition. The present study will use direct numerical simulations to validate a linear 2D-eigenvalue prediction method based on parabolized stability equations by Lin and Malik. This method is considered because it suggests that a number of symmetric and asymmetric modes exist and are stable or unstable on the attachment line depending on the Reynolds number. If validated, the approach would predict a number of modes which are linearly damped in the Reynolds number regime 100 to 245; however, these modes may grow nonlinearly and provide an explanation to this region.

Joslin, Ronald D.↗
DOE OSTI2023

On the evolution of scalar iso-surface area density in a turbulent mixing layer

In this paper, the transport equation for scalar iso-surface area density (Σ) in a turbulent, temporally developing mixing layer is examined. Exploring the spatial and temporal evolution of the terms in the Σ transport equation is vital to improving our understanding of turbulent flows characterized by distinct interfaces, e.g. the flame surface or the turbulent/non-turbulent interface. Previous work reported by the authors identified that Σ exhibits self-similar behaviour consistent with the development of the temporal mixing layer. Accordingly, each of the terms in the Σ transport equation is found to behave in a self-similar manner, though there are notable differences in the self-similar behaviours for each term. Based on the results presented herein, it is suggested that the rate of change of Σ (∂Σ/∂t) and the advection term scale with hλ Φ /ΔU, where h is the width of the mixing layer, λ Φ is the scalar Taylor length scale and ΔU is the velocity difference. The production and destruction terms are found to scale with an additional factor (ReSc) 1/2 . In contrast, the molecular diffusion term is found to scale with a factor (ReSc) –1/2 compared to ∂Σ/∂t. Importantly, it is found that the difference between the production and destruction terms, or net surface ‘stretch’, scales with the same factor as ∂Σ/∂t and the advection term, which may have a significant impact on how the evolution of Σ is understood and modelled in turbulent flows.

42 ENGINEERING↗
DOE OSTI2022

Impact of particle size and particle-flow-wall coupling on pressurized oxy-combustion in the down-fired burner

Concerns over climate change have led to numerous efforts in developing low-carbon energy technologies. Pressurized oxy-combustion (POC) is a promising candidate to reduce carbon emissions in power generation. Designing an effective burner plays a vital role in developing new coal combustion technologies. Because of the high pressure, the volume fraction of coal particles at the fuel inlet of the burner of a pressurized oxy-combustor is close or even higher than the maximum limit that commercial CFD codes (e.g., ANSYS FLUENT) can handle. At this high particle volume fraction, the interactions among particles, fluid flow, and wall need to be re-evaluated. The present computational work is the first step of a systematic analysis of the particle influence, like releasing method, releasing locating, and particle size, in a pilot-scale POC combustor, developed at Washington University in St. Louis (WUSTL). In a POC process, pulverized coal is burned under elevated pressure and O2-CO2 environment. Specifically, a 15-bar, 100 kWth, POC combustor is modeled employing ANSYS FLUENT, using Reynolds-averaged Navier-Stokes (RANS) modeling. It is revealed that for this pilot-scale, pressurized burner, velocity profiles of the near-wall region in this POC facility exhibit some discrepancy against the near-wall turbulent flow velocity profile. In order to investigate the particle influence in the near-wall region, particle releasing location will be investigated. Numerical simulation results exhibit the coupling effect of turbulence flow and particles in this case. The particle size also demonstrates a great effect on particle trajectory, then further has an impact on flame stability and temperature.

Li, Lei↗
NASA NTRS1987

Stochastic estimation of conditional eddies in turbulent channel flow

Several long-standing issues regarding linear estimation and coherent structures are addressed, and some questions that were addressed partially, but never with the benefit of full, three-dimensional information are answered. The objectives were to: determine how well linear estimates approximate the field obtained by true conditional averaging, using events such as those in quadrant analysis; determine the extent to which the three-dimensional linearly estimated fields correspond to coherent structures, and the degree and manner in which they differ; evaluate the type and nature of the structural information gained by employing several different types of events; and learn more about the 3-D structure of important coherent motions that occur in wall turbulence. The results indicate that linear stochastic estimation can be used effectively in the study of numerical data bases consisting of three-dimensional vector fields, both velocity and vorticity. Two-point stochastic estimation yields more structural information and more detail than single-point estimation. The structures observed occurred repeatedly within the flow, but much can not be said about their dominance or the probability of their occurrence without further systematic studies of their frequency.

Adrian, R. J.↗
NASA NTRS1973

Analysis of free turbulent shear flows by numerical methods

Studies are described in which the effort was essentially directed to classes of problems where the phenomenologically interpreted effective transport coefficients could be absorbed by, and subsequently extracted from (by comparison with experimental data), appropriate coordinate transformations. The transformed system of differential equations could then be solved without further specifications or assumptions by numerical integration procedures. An attempt was made to delineate different regimes for which specific eddy viscosity models could be formulated. In particular, this would account for the carryover of turbulence from attached boundary layers, the transitory adjustment, and the asymptotic behavior of initially disturbed mixing regions. Such models were subsequently used in seeking solutions for the prescribed two-dimensional test cases, yielding a better insight into overall aspects of the exchange mechanisms.

Korst, H. H.↗
NASA NTRS1976

Laser induced fluorescence applied to turbulent reacting flows

The saturated fluorescence method makes use of the great simplifications which occur when under conditions of intense radiation the excitation process becomes saturated. A description is presented of the saturated fluorescence method, taking into account rate equations and saturation, radiative transfer, the two-level system, a multilevel system, and measurements under saturation conditions. The detectability limits of the method are investigated. Fluorescence trapping is found to place an upper limit on the number density of the fluorescing species that can be measured without signal loss. Turbulence places time and spatial constraints on the measurements, but otherwise poses no difficulties. Saturated laser induced fluorescence spectroscopy appears to be a most promising method for measuring species concentrations in flames.

Daily, J. W.↗
NASA NTRS1984

A comprehensive model to determine the effects of temperature and species fluctuations on reaction rates in turbulent reaction flows

The use of silane (SiH4) as an effective ignitor and flame stabilizing pilot fuel is well documented. A reliable chemical kinetic mechanism for prediction of its behavior at the conditions encountered in the combustor of a SCRAMJET engine was calculated. The effects of hydrogen addition on hydrocarbon ignition and flame stabilization as a means for reduction of lengthy ignition delays and reaction times were studied. The ranges of applicability of chemical kinetic models of hydrogen-air combustors were also investigated. The CHARNAL computer code was applied to the turbulent reaction rate modeling.

Magnotti, F.↗
NASA NTRS2009

Characterization of the Effect of Wing Surface Instrumentation on UAV Airfoil Performance

Recently proposed flight research at NASA Dryden Flight Research Center (DFRC) has prompted study into the aerodynamic effects of modifications made to the surfaces of laminar airfoils. The research is focused on the high-aspect ratio, laminar-flow type wings commonly found on UAVs and other aircraft with a high endurance requirement. A broad range of instrumentation possibilities, such as structural, pressure, and temperature sensing devices may require the alteration of the airfoil outer mold line as part of the installation process. This study attempts to characterize the effect of installing this additiona1 instrumentation on key airfoil performance factors, such as transition location, lift and drag curves, and stall point. In particular, the general case of an airfoil that is channeled in the spanwise direction is considered, and the impact on key performance characteristics is assessed. Particular attention is focused on exploring the limits of channel depth and low-Reynolds number on performance and stall characteristics. To quantify the effect of increased skin friction due to premature transition caused by protruding or recessed instrumentation, two simplified, conservative scenarios are used to consider two potential sources of diaturbance: A) that leading edge alterations would cause linearly expanding areas (triangles) of turbulent flow on both surfaces of the wing upstream of the natural transition point, and B) that a channel or bump on the upper surface would trip turbulent flow across the whole upper surface upstream of the natural transition point. A potentially more important consideration than the skin friction drag increment is the change in overall airfoil performance due to the installation of instrumentation along most of the wingspan. To quantify this effect, 2D CFD simulations of the flow over a representative mid-span airfoil section were conducted in order to assess the change in lift and drag curves for the airfoil in the presence of disturbed flow due to the installed instrumentation. A discussion as to the impact on high-altitude and low-speed operation of this and similar aircraft is provided.

Ratnayake, Nalin A.↗
NASA NTRS1999

Computation of Turbulent Wake Flows in Variable Pressure Gradient

Transport aircraft performance is strongly influenced by the effectiveness of high-lift systems. Developing wakes generated by the airfoil elements are subjected to strong pressure gradients and can thicken very rapidly, limiting maximum lift. This paper focuses on the effects of various pressure gradients on developing symmetric wakes and on the ability of a linear eddy viscosity model and a non-linear explicit algebraic stress model to accurately predict their downstream evolution. In order to reduce the uncertainties arising from numerical issues when assessing the performance of turbulence models, three different numerical codes with the same turbulence models are used. Results are compared to available experimental data to assess the accuracy of the computational results.

Duquesne, N.↗
NASA NTRS2001

Filtered Mass Density Function for Design Simulation of High Speed Airbreathing Propulsion Systems

The objective of this research is to develop and implement new methodology for large eddy simulation of (LES) of high-speed reacting turbulent flows. We have just completed two (2) years of Phase I of this research. This annual report provides a brief and up-to-date summary of our activities during the period: September 1, 2000 through August 31, 2001. In the work within the past year, a methodology termed "velocity-scalar filtered density function" (VSFDF) is developed and implemented for large eddy simulation (LES) of turbulent flows. In this methodology the effects of the unresolved subgrid scales (SGS) are taken into account by considering the joint probability density function (PDF) of all of the components of the velocity and scalar vectors. An exact transport equation is derived for the VSFDF in which the effects of the unresolved SGS convection, SGS velocity-scalar source, and SGS scalar-scalar source terms appear in closed form. The remaining unclosed terms in this equation are modeled. A system of stochastic differential equations (SDEs) which yields statistically equivalent results to the modeled VSFDF transport equation is constructed. These SDEs are solved numerically by a Lagrangian Monte Carlo procedure. The consistency of the proposed SDEs and the convergence of the Monte Carlo solution are assessed by comparison with results obtained by an Eulerian LES procedure in which the corresponding transport equations for the first two SGS moments are solved. The unclosed SGS convection, SGS velocity-scalar source, and SGS scalar-scalar source in the Eulerian LES are replaced by corresponding terms from VSFDF equation. The consistency of the results is then analyzed for a case of two dimensional mixing layer.

Drozda, T. G.↗
NASA NTRS1979

Investigations of coherent structures in free turbulent shear flows

The dynamics of large-scale coherent structures in general, and studies based on flow-visualization and phase-locked hot-wire measurements of the structures in the near fields of circular jets are considered. A study involving the nature of coherent structures under conditions of stable vortex pairing induced by controlled axisymmetric acoustic excitation reveals that azimuthal coherence initially enhanced by the excitation is lost before the end of the potential core through evolution of azimuthal lobe structures and turbulent breakdown. The evolution of a spark-induced spot in an axisymmetric turbulent mixing layer is also investigated, and the coherent Reynolds stress associated with the spot is found to be much higher than the background turbulence Reynolds stress. In addition, the state of organization in a high Reynolds number unperturbed axisymmetric mixing layer is examined, and it is shown that the shear layer is infrequently organized and the motions are intensely three-dimensional, while tearing and fractional pairing occur as frequently as complete pairing.

Hussain, A. K. M. F.↗
NASA NTRS2019

Weighted Least-Squares Cell-Average Gradient Construction Methods for the VULCAN-CFD Second-Order Accurate Unstructured-Grid Cell-Centered Finite-Volume Solver

The ability to solve the equations governing the hypersonic turbulent flow of a real gas on unstructured grids using a spatially-elliptic, 2nd-order accurate, cell-centered, finite-volume method has been recently implemented in the VULCAN-CFD code. The construction of cell-average gradients using a weighted linear least-squares method and the use of these gradients in the construction of the inviscid fluxes is the focus of this paper. A comparison of least-squares stencil construction methodologies is presented and approaches to augment the number of cells participating in the stencil while preserving accuracy are explored. Due to our interest in hypersonic flow, a robust multidimensional cell-average gradient limiter procedure that is consistent with the stencil used to construct the cell-average gradients is described and investigated. Canonical problems are computed to illustrate the challenges and investigate the accuracy, robustness and convergence behavior of the cell-average gradient methods on unstructured cell-centered finite-volume grids. Finally, thermally perfect, chemically frozen, Mach 8 turbulent flow of air around a blunt wedge is computed to demonstrate the robustness and convergence behavior of the new method for constructing stencils of use in a weighted linear least-squares gradient method for a hypersonic flow.

White, Jeffery A.↗
NASA NTRS2019

Boundary Layer Stability and Transition in a Chemically Reacting Martian Atmosphere Using LASTRAC

The Thermal Protection System (TPS) is a significant portion of the mass of reentry vehicles, planetary probes, and Martian entry vehicles. Reducing this mass has benefits in terms of decreased fuel requirements and increased payload; however, due to the high risk and uncertainty, the TPS or heat shields are designed conservatively by assuming fully turbulent flow. Laminar flow results in reduced heat flux, and improved transition prediction has the potential to reduce TPS mass and uncertainty in aerothermodynamic predictions. Limited previous research exists examining the problem of transition prediction for Martian atmospheric entry, with studies available on transition on the Mars Science Laboratory TPS. Although transition was demonstrated in wind-tunnel tests, uncertainty in the transition location resulted in a TPS designed for fully turbulent flow, and therefore greater mass than required for a partially laminar condition. In this work, we extend the boundary layer stability code LASTRAC, recently modified to include chemical and thermal nonequilibrium capabilities, to a model of the Martian atmosphere. LASTRAC provides Parabolized Stability Equations (PSE) as well as Linear Stability Theory (LST) to predict the stability of a boundary layer and transition with semi-empirical e(sup N) methods. Results included in this work compare disturbance growth characteristics between air and Martian atmosphere at similar non-dimensional freestream conditions on a simple flat plate geometry. Both chemical nonequilibrium and thermochemical nonequilibrium, as well as both PSE and LST, are used.

Kline, H. L.↗
NASA NTRSDate not supplied

Boundary Layer Stability and Transition in a Chemically Reacting Martian Atmosphere using LASTRAC

The Thermal Protection System (TPS) is a significant portion of the mass of reentry vehicles, planetary probes, and Martian entry vehicles. Reducing this mass has benefits in terms of decreased fuel requirements and increased payload; however, due to the high risk and un-certainty, the TPS or heat shields are designed conservatively by assuming fully turbulent flow. Laminar flow results in reduced heat flux, and improved transition prediction has the potential to reduce TPS mass and uncertainty in aerothermodynamic predictions. Limited previous research exists examining the problem of transition prediction for Martian atmospheric entry, with studies available on transition on the Mars Science Laboratory TPS. Although transition was demonstrated in wind-tunnel tests, uncertainty in the transition location resulted in a TPS designed for fully turbulent flow, and therefore greater mass than required for a partially-laminar condition. In this work, we extend the boundary layer stability code LASTRAC, recently modified to include chemical and thermal nonequilibrium capabilities, to a model of the Martian atmosphere. LASTRAC provides Parabolized Stability Equations (PSE) as well as Linear Stability Theory (LST) to predict the stability of a boundary layer and transition with semi-empirical eN methods. Results included in this work compare disturbance growth characteristics between air and Martian atmosphere at similar nondimensional freestream conditions on a simple flat plate geometry. Both chemical nonequilibrium and thermochemical nonequilibrium, as well as both PSE and LST, are used.

Heather L Kline↗
NASA NTRS1986

Modeling turbulent, reacting flow

Several of the approximations or models involved in the development of a numerical combustor flow code are examined. In the first section, the importance of numerical accuracy is illustrated, and the impact that improved-accuracy schemes have on slowing convergence is demonstrated. Solution algorithms that can speed convergence are discussed and some performance features of these algorithms are illustrated. A sample calculation displaying the importance of boundary conditions on a three-dimensional numerical prediction is presented. The inaccuracy of a current turbulence model in highly turbulent (nonequilibrium) regions is described. Finally, the surprisingly good performance of a six-flux model in describing radiation heat transfer is displayed. In all the areas examined, continued research is still needed, but valuable engineering tools are available today.

Claus, Russell W.↗