SEARCH · Engineering Papers

Results for “surface cracks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Through-the-thickness fatigue crack closure behavior in an aluminum alloy

The variation in fatigue crack closure behavior across the thickness of aluminum alloy specimens was investigated. The specimen geometries examined were the middle crack tension M(T) and compact tension C(T). The fatigue crack closure behavior was determined using remote displacement and strain gages, near tip strain gages, and fatigue striations. A hybrid experimental/numerical method was also used to infer the crack opening loads. The results indicate a variation in crack opening load, of 0.2 in the specimen interior to 0.4 to 0.5 at the surface.

Dawicke, D. S.↗

NASA NTRS1993

Spring-Tab Lock Washer

Improved spring-tab lock washer offers alternative to such positive-locking devices as cotter pins and lock wires and to conventional split-ring lock washers. Does not dig into fastened parts with sharp edges; less likely to inflict scratches causing cracks. Contains three winglike spring tabs and three alignment pips, pressed into mating dimples in surface of part to be fastened. Spring tabs on lock washer allow only clockwise rotation (tightening) of bolt or nut.

Finckenor, Jeff↗

NASA NTRS1997

Investigation of Teflon FEP Embrittlement on Spacecraft in Low Earth Orbit

Teflon(registered trademark) FEP (fluorinated ethylene-propylene) is commonly used on exterior spacecraft surfaces in the low Earth orbit (LEO) environment for thermal control. Silverized or aluminized FEP is used for the outer layer of thermal control blankets because of its low solar absorptance and high thermal emittance. FEP is also preferred over other spacecraft polymers because of its relatively high resistance to atomic oxygen erosion. Because of its low atomic oxygen erosion yield, FEP has not been protected in the space environment. Recent, long term space exposures such as on the Long Duration Exposure Facility (LDEF, 5.8 years in space), and the Hubble Space Telescope (HST, after 3.6 years in space) have provided evidence of LEO environmental degradation of FEP. These exposures provide unique opportunities for studying environmental degradation because of the long durations and the different conditions (such as differences in altitude) of the exposures. Samples of FEP from LDEF and from HST (retrieved during its first servicing mission) have been evaluated for solar induced embrittlement and for synergistic effects of solar degradation and atomic oxygen. Micro-indenter results indicate that the surface hardness increased as the ratio of atomic oxygen fluence to solar fluence decreased for the LDEF samples. FEP multilayer insulation (MLI) retrieved from HST provided evidence of severe embrittlement on solar facing surfaces. Micro-indenter measurements indicated higher surface hardness values for these samples than LDEF samples, but the solar exposures were higher. Cracks induced during bend testing were significantly deeper for the HST samples with the highest solar exposure than for LDEF samples with similar atomic oxygen fluence to solar fluence ratios. If solar fluences are compared, the LDEF samples appear as damaged as HST samples, except that HST had deeper induced cracks. The results illustrate difficulties in comparing LEO exposed materials from different missions. Because the HST FEP appears more damaged than LDEF FEP based on depth of embrittlement, other causes for FEP embrittlement in addition to atomic oxygen and ultraviolet (UV) radiation, such as thermal effects and the possible role of soft x-ray radiation, need to be considered. FEP that was exposed to soft x-rays in a ground test facility, showed embrittlement similar to that witnessed in LEO, which indicates that the observed differences between LDEF and HST FEP might be attributed to the different soft x-ray fluences during these two missions.

deGroh, Kim K.↗

NASA NTRS2002

Micro-Cracking Detection in Laminated Composites

Porosity and fatigue cracking are two critical factors that affect the performance and safety of cryogenic fuel tanks and feedlines made from unlined laminated or weaved carbon/epoxy materials. This paper presents the experiments to induce fatigue cracking of laminated composites through thermal cycling as well as the feasibility of using Thermography and Ultrasound Spectroscopy technology (UT) to detect and measure such micro-cracking. Carbon/epoxy laminated composite panels were built and cut into strips. These specimens were partially submerged in liquid nitrogen while subjected to various loads on a test machine. Edges of some specimens were polished and etched to determine the degree of micro-cracking. The rest of specimens were then examined with Thermography and Ultrasound Spectroscopy NDE systems to investigate the feasibility of finding such micro-cracking in the laminated composites. Thermography is utilized to determine changes in thermal diffusivity. The degree of cracking may reduce the apparent thermal diffusivity and therefore change the thermal response on the surface. Thermography testing was conducted on a group of specimens where it is desired to have some correlation between the predetermined stress and the thermography data. Ultrasound Spectroscopy was used to determine peak changes between the pre-stressed and stressed samples. Data from the inspections were analyzed and the results are presented in this paper.

Chu, Tsuchin↗

NASA NTRS2021

Small Volcanic Vents of the Tharsis Volcanic Province, Mars

Distributed-style volcanism is an end member of terrestrial volcanism that produces clusters of small volcanoes when isolated magma bodies ascend from broad magma source regions. Volcano clusters can develop over millions of years, one volcano at a time, and can be used to infer unobserved geologic phenomena, including subsurface stresses and cracks during eruption periods. The Tharsis Volcanic Province covers approximately one quarter of the Martian surface and hosts a large concentration of small volcanoes that formed from distributed volcanism. We present a catalog of 1106 small volcanic vents identified within Tharsis Volcanic Province. This catalog includes morphologic measurements for each cataloged vent. Vent lengths range from 71 m to 51 km, widths range from 40 m to 3.1 km, and 90% of vents have lengths at least 1.5 times their widths. Additionally, 90% of edifices associated with vents have topographic prominences <100 m. Vents are found throughout Tharsis, though they generally form clusters near large volcanoes or among large graben sets. Older regions with volcanic eruption ages of >1 Ga are found at the Tharsis periphery in the Tempe-Mareotis region and Syria Planum. Vents in the Tharsis interior have reported ages <500 Ma. Regional trends in vent orientation and intervent alignment are dependent on nearby central volcanoes and fossae. We use these findings to hypothesize that within the most recent 500 Ma, magma was present under and to the east of the Tharsis Montes and that some of this magma erupted and built hundreds of small volcanoes in this region.

Distributed volcanism↗

NASA NTRS2019

Temperature Mapping at the Thermal Barrier Coating/Bond Coat Interface by Luminescence Lifetime Imaging Using Integrated Erbium-Doped Sublayers

Full-field temperature mapping of thermal barrier coated components by either infrared thermography or phosphor thermometry has been limited to surface temperature mapping even though temperature mapping at the thermal barrier coating (TBC)/bond coat interface is more relevant for evaluating the TBC thermal protection performance. For the first time, 2D temperature mapping at the TBC/bond coat interface has now been achieved by full-field luminescence lifetime imaging measurements of emission from a thin erbium-doped yttria-stabilized zirconia (YSZ) sensing layer integrated into the TBC below the overlying undoped YSZ. This new capability was applied to map temperatures at the TBC/bond coat interface for TBC-coated specimens subjected to a heat flux produced by the NASA Glenn high heat flux laser facility. In particular, thermal gradients at the TBC/bond coat interface were mapped in regions where the TBC was subjected to erosion or to mechanically induced delamination crack propagation. Finally, temperature mapping of the TBC/bond coat interface was used to evaluate the effectiveness of surface air film cooling at the TBC/bond coat interface.

Eldridge, Jeffrey I.↗

DOE OSTI2023

Plasma surface ionization wave interactions with single channels

Abstract The study of plasma surface ionization waves (SIWs) in recent years has primarily focused on planar surfaces and periodic two dimensional structures. In application, substrates are likely to have non-planar morphology such as cracks, pores, and steps. Additionally, targets for the applications of medicine or catalysis may have targets with heterogeneous composition. This classification of targets are brought under the umbrella of complex interfaces. In this work, plasma SIWs were incident on a complex target consisting of a single channel cut into glass slides. The SIW velocities for the in-channel portion of the wave and radially propagating portion of the wave were tracked. It was found that surface wave velocities are not significantly affected by channel geometry, but primarily increase with pulse energy. A third propagation direction for the SIW is characterized in the azimuthal direction relative to the radial portion of the wave. Channel geometry is found to greatly effect the area treated by the plasma but not the propagation velocity of the surface wave. Surface wave morphology and the impact on application is also discussed. A simple model was introduced to understand the mechanisms behind SIW escape from a channel. It was found that the ratio of pulse energy to a geometry dependent minimum energy can predict the escape angle of a SIW from single channels.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Suppressing strain propagation in ultrahigh-Ni cathodes during fast charging via epitaxial entropy-assisted coating

Surface reconstruction and the associated severe strain propagation have long been reported as the major cause of cathode failure during fast charging and long-term cycling. Despite tremendous attempts, no known strategies can simultaneously address the electro-chemomechanical instability without sacrificing energy and power density. Here we report an epitaxial entropy-assisted coating strategy for ultrahigh-Ni LiNi x Co y Mn 1-x-y O 2 (x ≥ 0.9) cathodes via an oriented attachment-driven reaction between Wadsley-Roth phase-based oxides and the layered-oxide cathodes. Further, the high anti-cracking and anti-corrosion tolerances as well as the fast ionic transport of the entropy-assisted surface effectively improved the fast charging/discharging capability, wide temperature tolerance and thermal stability of the ultrahigh-Ni cathodes. Comprehensive analysis from the primary and secondary particle level to the electrode level using multi-scale in situ synchrotron X-ray probes reveals greatly reduced lattice dislocations, anisotropic lattice strain and oxygen release as well as improved bulk/local structural stability, even when charging beyond the threshold state of charge (75%) of layered cathodes. Layered Ni-rich oxide cathodes are susceptible to challenges with surface reconstruction and strain propagation, limiting their cyclability. The authors propose a solution involving oriented attachment-driven reactions, utilizing Wadsley-Roth nanocrystals and layered oxide to induce an epitaxial entropy-assisted coating, effectively addressing these issues.

25 ENERGY STORAGE↗

DOE OSTI2021

An investigation into the effects of cyclic strain rate on the high cycle and very high cycle fatigue behaviors of wrought and additively manufactured Inconel 718

Additive Manufacturing (AM) has increasingly been used to fabricate parts in aerospace applications, which may require service lives beyond ten-million cycles due to the imposed high loading frequencies. Understanding the very high cycle fatigue (VHCF) behavior of these additive manufactured (AM) parts is an important step towards their design and qualification processes. This study focuses on the high cycle fatigue (HCF) and VHCF behaviors of both wrought and laser beam-powder bed fusion (LB-PBF) fabricated Inconel 718 in machined/polished surface condition, emphasizing on the influence of test frequency (i.e., cyclic strain rate). Uniaxial, fully-reversed force- and stress-controlled fatigue tests were conducted utilizing a servo-hydraulic and an ultrasonic test system operating at 5 Hz and 20 kHz, respectively, on wrought as well as LB-PBF vertically and diagonally built specimens. Fatigue cracks in the majority of the specimens were found to initiate from intra-granular slip bands near or at the surface, which gives rise to strong anisotropy in fatigue resistance in LB-PBF specimens due to the presence of columnar grains along the build directions. Longer fatigue lives were obtained at 20 kHz, which was ascribed to possibly lower-than-intended stresses applied in the ultrasonic tests. The corrected stress-life fatigue data at 20 kHz were found to converge to the one obtained from conventional testing at 5 Hz, implying no effect of cyclic strain rate on the fatigue behavior of Inconel 718 regardless of the fabrication process. The findings of this work confirm the use of ultrasonic fatigue testing to expedite generation of AM materials data to keep up with the current demand; however, the applied stress may need to be corrected.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Propagation of Cryogenic Thermal Fractures from Unconfined PMMA Boreholes

In cryogenic fracturing, a rock surface exposed to cryogenic fluids undergoes a large thermal gradient, and the resultant local tensile stress overcomes rock strength and initiates fractures. This study investigates the development of cracks generated from the cryogenic treatment of a borehole under no external confining stress on specimens. The experiments were performed on transparent PMMA specimens to observe fracture proliferation around boreholes. Liquid nitrogen was flowed through the boreholes to cool the borehole surface. The results show that initial fracture growth is characterized by abrupt starts and stops, and as the fracture propagates outward, the growth appears more continuous. In an early stage, horizontal/radial fractures and vertical fractures are the defining patterns. Horizontal fractures tend to be separated by a specific exclusion distance (i.e., spacing between cracks). While distinct horizontal/vertical fractures and exclusion distance manifest themselves at an early stage, fractures resulting from fracture interactions and curvatures can develop into complex shapes at later stages. Cryogenic thermal loading induces distinctively curved fractures. The tendency of curvature may prevent greater penetration. An increase in the borehole pressure during liquid nitrogen flow, however, can lessen fracture tortuosity and facilitate radial propagation. A high flow pressure and rate are also advantageous in that they accelerate cooling and fracture propagation.

42 ENGINEERING↗

NASA NTRS2017

Tutorial on Atomic Oxygen Effects and Contamination

Atomic oxygen is the most predominant specie in low Earth orbit (LEO) and is contained in the upper atmosphere of many other planetary bodies. Formed by photo-dissociation of molecular oxygen, it is highly reactive and energetic enough to break chemical bonds on the surface of many materials and react with them to form either stable or volatile oxides. The extent of the damage for spacecraft depends a lot on how much atomic oxygen arrives at the surface, the energy of the atoms, and the reactivity of the material that is exposed to it. Oxide formation can result in shrinkage, cracking, or erosion which can also result in changes in optical, thermal, or mechanical properties of the materials exposed. The extent of the reaction can be affected by mechanical loading, temperature, and other environmental components such as ultraviolet radiation or charged particles. Atomic oxygen generally causes a surface reaction, but it can scatter under coatings and into crevices causing oxidation much farther into a spacecraft surface or structure than would be expected. Contamination can also affect system performance. Contamination is generally caused by arrival of volatile species that condense on spacecraft surfaces. The volatiles are typically a result of outgassing of materials that are on the spacecraft. Once the volatiles are condensed on a surface, they can then be fixed on the surface by ultraviolet radiation andor atomic oxygen reaction to form stable surface contaminants that can change optical and thermal properties of materials in power systems, thermal systems, and sensors. This tutorial discusses atomic oxygen erosion and contaminate formation, and the effect they have on typical spacecraft materials. Scattering of atomic oxygen, some effects of combined environments and examples of effects of atomic oxygen and contamination on spacecraft systems and components will also be presented.

Earth orbital environments↗

DOE OSTI2021

Piezoelectric response and failure behavior of cement paste under external loading

We study the elastic behavior and rupture mechanism of Calcium Silicate Hydrates (C-S-H) in response to tensile loading. For the three tensile axes, initial defects are spotted in the interlayer regions. However, the crack propagation is rather different depending on the axis of tensile. The cup-and-cone failure surface shows the ductile feature of C-S-H in the x and y directions; while the devastating rupture mode confirms the brittle feature of C-S-H in the z direction. Piezoelectricity was investigated using the charge fluctuation method. The polarization variation in response to small strain was also investigated and piezoelectric coefficients were derived. Furthermore, dependence of elastic and piezoelectric properties over external pressure was analyzed. Results reveal an improvement of the mechanical properties and the ultimate strength especially in the z direction; whereas the non-piezoelectricity remains unchanged despite the rearrangement of atoms induced by the external applied pressure.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Summary of Alloy 617 and Alloy 709 Elevated Temperature Crack Growth Test Results from the Planned FY24 Crack Growth Test Activities

This report covers the results from crack growth rate testing performed at Idaho National Laboratory in the fiscal year 2024. It includes two creep crack growth rate tests and two creep-fatigue crack growth rate tests. Results are shown for each of these tests, included crack growth measured during the test using direct current potential drop, and measurements based off of the fracture surface. Load line displacement, as well as load, were also collected during the tests. Detailed analysis of the results will continue into the next fiscal year, however, a number of potential improvements to the equipment and testing procedures were identified that will increase testing reliability and throughput, as well as decrease complications with the analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1997

Effects of Interface Modification on Mechanical Behavior of Hi-Nicalon Fiber-Reinforced Celsian Matrix Composites

Unidirectional celsian matrix composites having approx. 42 volume percent of uncoated or BN/SiC-coated Hi-Nicalon fibers were tested in three-point bend at room temperature. The uncoated fiber-reinforced composites showed catastrophic failure with strength of 210 +/- 35 MPa and a flat fracture surface. In contrast, composites reinforced with BN/SiC-coated fibers exhibited graceful failure with extensive fiber pullout. Values of first matrix cracking stress and strain were 435 +/- 35 MPa and 0.27 +/- 0.01 %, respectively, with ultimate strength as high as 960 MPa. The elastic Young's modulus of the uncoated and BN/SiC-coated fiber-reinforced composites were measured as 184 q 4 GPa and 165 +/- 5 GPa, respectively. Fiber push-through tests and microscopic examination indicated no chemical reaction at the uncoated or coated fiber-matrix interface. The low strength of the uncoated fiber-reinforced composite is probably due to degradation of the fibers from mechanical surface damage during processing. Because both the coated and uncoated fiber reinforced composites exhibited weak interfaces, the beneficial effect of the BN-SiC dual layer is primarily the protection of fibers from mechanical damage during processing.

Bansal, Narottam P.↗

DOE OSTI2021

SNF Interim Storage Canister Corrosion and Surface Environment Investigations (FY21 Status Report)

This progress report describes work performed during FY21 at Sandia National Laboratories (SNL) to assess the localized corrosion performance of canister materials used in the interim storage of spent nuclear fuel (SNF). Of particular concern is stress corrosion cracking (SCC), by which a through-wall crack could potentially form in a canister outer wall over time intervals that are shorter than possible dry storage times. In FY21, modeling and experimental work was performed that further defined our understanding of the potential chemical and physical environment present on canister surfaces at both marine and inland sites. Research also evaluated the relationship between the environment and the rate, extent, and morphology of corrosion, as well as the corrosion processes that occur. Finally, crack growth rate testing under relevant environmental conditions was initiated.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1981

Further Study of near Solidus Intergranular Cracking in Inconel 718

A series of tests, performed to determine the strain necessary to initiate intergranular cracking in Inconel 718 as a function of temperature, contained enough scatter near the melting temperature that questions remained as to the best curve of curves to fit to the data. Fracture surface analysis showed that the scatter was due to incipient melting in the grain boundary region. The melting contributed to low fracture strain but had only a small on the incipient cracking strain. Gleeble tests, which could be interrupted by water quenching, were used to study the incipient intergranular melting of Inconel 718. This modified weld simulation test provided a sufficiently rapid quench to preserve the intergranular microstructure created during incipient melting. This structure was studied both microscopically and with energy dispensive X-ray analysis. The implications of incipient melting and low-strain incipient cracking on the development of microfissuring envelopes are discussed.

Thompson, R. G.↗

DOE OSTI2020

Facile and scalable dry surface doping technique to enhance the electrochemical performance of LiNi 0.64 Mn 0.2 Co 0.16 O 2 cathode materials

Lithium nickel manganese cobalt oxide (NMC) is one of the dominant cathode materials in lithium-ion batteries. In this study a simple, efficient and scalable surface doping technique is successfully demonstrated, which can be readily used in mass production of cathode materials. For the first time neodymium oxide (Nd 2 O 3 ) has been employed as the surface doping agent. The Nd-doped NMC shows greatly improved cycling and rate performance, and the enhanced cycling stability has been demonstrated in full pouch cells, with a 17.5% increase in capacity retention after 300 cycles. Fewer cracks have been observed in the doped NMC after cycling, and in situ X-ray diffraction reveals the suppressed lattice collapse by Nd doping. Greatly suppressed surface phase change has been confirmed by HR-TEM and EELS. The result suggests great promise in using this dry doping technique to enhance the electrochemical performance of NMC cathodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Oxidation of 3D-printed SiC in air and steam environments

Here, the high-temperature oxidation of additively manufactured and chemically vapor infiltrated (3D-printed SiC) has been compared to chemical vapor deposited (CVD) SiC. 100-h isothermal exposures were conducted at 1425° and 1300°C at 1 atm under both dry air and steam environments. A SiC reaction tube was utilized to reduce silica volatility. After steam oxidation at 1425° and 1300°C, on the 3D-printed SiC surface, which was intrinsically rougher than the CVD surface, scales were 70%–90% thicker at the convex regions compared to concave/flat regions. In the convex regions, large cracks perpendicular to the oxidizing interface were observed. After dry air oxidation, scale thicknesses were comparable between 3D-printed SiC and CVD SiC, regardless of geometry. Finite element modeling, conducted to elucidate the relationship between SiC geometry and ß- to α-cristobalite transformation stress, determined cristobalite transformation tensile stresses to be on the order of 103 MPa during cool down, assuming a 6 vol% reduction. Compared to flat SiC substrates, tensile transformation stresses were elevated at concave regions and relaxed at convex regions. Combined with specimen mass gain (accounting for the rougher surface) of 3D-printed SiC being 15%–32% higher for 3D-printed SiC after 1300°C and 1425°C steam oxidation, the work presented concludes that the increased oxidation of 3D-printed SiC is primarily caused by tensile hoop stresses driven by oxidation volume expansion. Lastly, the efficacy of the 3D-printing method is demonstrated through the production of tristructural isotropic imbedded 3D-printed SiC fuel forms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗